Phone

    00852-6915 1330

switch Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

Resistors

What is a Toggle Switch?

CatalogⅠ IntroductionⅡ What is a Toggle Switch?Ⅲ Structure of a Toggle Switch3.1 Lever3.2 Spring3.3 O-ring3.4 Plunger3.5 Moving Armature3.6 Case3.7 BaseⅣ Types of Toggle Switches4.1 SPST (Single Pole Single Throw) Toggle Switches4.2 SPDT (Single Pole Double Throw) Toggle Switches4.3 DPST (Double Pole Single Throw) Toggle Switches4.4 DPDT (Double Pole Double Throw) Toggle SwitchesⅤ Toggle Switch Accessories5.1 Switch Guards5.2 Rubber BootⅥ Applications of Toggle SwitchesⅦ How to Wire a Toggle SwitchⅧ How to Install a Toggle Switch8.1 Installing a Switch in Your Device's Panel8.2 Connecting Your Toggle Switch to Your Device's WiringⅨ Precautions for the Use of the Toggle SwitchⅩ Frequently Asked Questions About Toggle Switches Ⅰ IntroductionYou may not understand what toggle switches are or how they function, but I'm sure you've seen them. Even if you've never seen one in person, you've probably seen old war movies. Consider an image of an ancient airplane cockpit or perhaps an old vehicle dashboard. Toggle switches are the small shiny levers that pilots or drivers use to turn on and off.  A toggle switch is an electromechanical device that flips a lever back and forth to turn on and off a circuit or switch between numerous circuits. This article will show the datails of toggle switches to help you learn more about them. Ⅱ What is a Toggle Switch?The toggle switch is a type of electrical switch distinguished by the presence of a handle or lever that allows the flow of electrical power from a power supply to a device of some kind  to be controlled. An electrical toggle switch can be utilized in a variety of applications, both commercial and residential. Switches of this sort are very straightforward to use and can endure for many years before needing to be replaced. A toggle switch has become a catch-all name for almost any sort of electrical control that uses a handle, lever, or other type of rocking mechanism to manage the flow of electrical current. Some switches, particularly industrial toggles, are quite massive and are built with a metal lever with a handle situated in the centre of the lever. These industrial designs frequently require a tremendous deal of effort to move from one position to another for safety concerns, and may be supplied with locks or timed mechanisms as part of the safety precautions. Other types of switches of this type include little devices that can be controlled with a finger. One of the more popular types of toggles found today is in the home. The toggle light switch is a device that controls the passage of power from the home's main wiring to the wiring of an appliance or fixture. This sort of toggle is typically installed in the wall and covered with a basic switch cover that exposes the lever. It is possible to turn on overhead lights or give electricity to outlets wired directly to the switch by sliding the toggle up and down. In some home designs, a toggle switch right inside the front door controls plugs in the adjacent room, allowing you to easily turn on lamps plugged into those outlets and flood the space with light upon entering the space. While push buttons and virtual keypads are becoming more popular in homes and some commercial and corporate settings, toggle switches remain the most popular choice for directing the flow of power from a source to a device. The switch's simplicity ensures that the possibilities of it breaking down or malfunctioning are low, making it an appealing alternative. Even if the switch finally wears out, the procedure of replacing a toggle switch may usually be completed in minutes and with very little effort. Ⅲ Structure of a Toggle SwitchThis is an example of an ultra subminiature toggle switch with ingress protection that meets the IEC 60529 standard's IP64 standards.It is made up of a lever, a spring, O-rings, a plunger, a moving armature, a case, and a base.  3.1 LeverThe user can toggle between ON and OFF by pressing the lever in the working direction. Levers are often composed of plastic, however on larger devices, some are constructed of metal to boost longevity. 3.2 SpringThe spring is contained within the lever. It pushes the lever outwards and is always in touch with the base. 3.3 O-ringThese are circular rubber components that protect the moving parts in the case and lever from foreign items by sealing the connections between the base and the case. 3.4 PlungerThe plunger is a resin component attached to the bottom of the lever that is designed to be in constant contact with the bottom of the base to limit the lever's movement range. 3.5 Moving ArmatureA U-shaped contact is incorporated in the lever. The tip of the U-shape contact travels with the lever, and the terminal is placed between the tips to activate the switch mechanism's ON state. This makes extraneous things difficult to come between the contacts. 3.6 CaseThe case protects the switch's internal components. It also supports the lever through the upper surface hole. 3.7 BaseThe base, together with the casing, are used to safeguard the switch's internal components. The switch terminals extend from the bottom of the base. Ⅳ Types of Toggle SwitchesWhen choosing a toggle switch, like with any other electrical component, it is critical to evaluate the characteristics of your circuit. Toggle switches are available in a number of voltages, amperages, and power ratings, and are made from a variety of materials. Aside from rating, toggle switches are classified mostly depending on their operating designs. They are classified based on the number of unique positions into which the levers can be switched. A 2-position toggle switch is the most basic kind. This is frequently toggled on and off. Toggle switches are also commonly encountered in three-position configurations. This is where the ease of use ends. There are 4-position, 5-position, and 6-position circuits available, and you can order as many as you need. These multiple position toggle switches, on the other hand, are made for specific applications and are more difficult to find. However, the most common way to categorize toggle switches is by the number of poles and throws. The number of independent circuits that the switch may manage at the same time is referred to as its pole. The number of various outputs that each switch may link its input to is referred to as its throw. Toggle switches are categorised as SPST, SPDT, DPST, DPDT, and unique switches that are not classified under the four popular classifications. 4.1 SPST (Single Pole Single Throw) Toggle Switches SPST On-Off SPST toggle switches control a single circuit. It has two operational modes: ON and OFF. By switching between these two locations, the connection between the conductors linked to its two terminals is either closed or opened. 4.2 SPDT (Single Pole Double Throw) Toggle Switches Single pole double throw toggle switches come in two varieties. They are the two-position ON/ON variation and the three-position ON/OFF/ON variant. *SPDT ON/ON SPDT On-On This is a three-terminal switch that regulates only one circuit. The input is connected to the middle terminal, known as the common. The output is represented by the two outer terminals, which are commonly referred to as A and B. The switch lever has two locations, allowing the input to be connected to either terminal A or B. *SPDT ON/OFF/ON SPDT On-Off-On This is another three-terminal switch that regulates a single circuit. The input, like SPDT ON/OFF, is connected to the common. The main difference with this switch is that the lever has three positions. The circuit is switched between terminals A and B by the end positions. The center position, on the other hand, is an off position. This indicates it does not link the input terminal to either of the output terminals. 4.3 DPST (Double Pole Single Throw) Toggle Switches DPST On-Off This is two SPST switches joined together and controlled by the same lever. This switch has four terminals, two inputs and two outputs. They function as ON/OFF switches. DPST switches are commonly used with 220V equipment to open and close both 110V lines simultaneously. 4.4 DPDT (Double Pole Double Throw) Toggle Switches DPDT toggle switches are classified into three categories. There are two ON/ON positions, as well as three ON/OFF/ON and ON/ON/ON positions. *DPDT ON/ON DPDT On-On This is made up of two SPDT ON/OFF switches that are linked together and controlled by a single lever. It is a six-terminal switch with two independent circuits. The input or common terminals are linked to both A and B terminals at the same time. On the lever, there are only two places. *DPDT ON/OFF/ON DPDT On-Off-On This switch has six terminals and controls two distinct circuits. The lever, on the other hand, has three positions. The inputs are connected to both A and B terminals via the two end locations. However, the middle position does not link the input to any of the output terminals, resulting in an open or off circuit. *DPDT ON/ON/ON  This one is a little more difficult. It is also a three-position switch, with the input going to the center terminals. The lever's two end locations link the input to either both A or both B terminals at the same time. The middle position is what distinguishes this switch. When the lever is centered, one of the inputs is linked to its corresponding A terminal and the other to its corresponding B terminal. As it goes to the middle position, the switch only moves one circuit at a time. There are two types that are utilized to distinguish which side switches over first. These switches are most frequently found on electric guitars. Ⅴ Toggle Switch AccessoriesIf further accessories are required for your project, our toggle switches are available. 5.1 Switch Guards Toggle switch guards are primarily used to safeguard the switch and prevent it from being accidentally switched off or on. The toggle is protected from inadvertent movement by the solid shell. 5.2 Rubber Boot To protect against dust and moisture, a toggle switch rubber boot is employed. The boot completely encloses the base, resulting in a dust-tight seal. Ⅵ Applications of Toggle SwitchesTelecommunications and Networking Equipment (Wireless Network Cards, Handheld Devices, Reset Switches)Instrumentation (Shut-Off Switches, Controllers)Industrial Controls (Grips, Joysticks, Power Supplies)Test and Measurement EquipmentElevator ControlsFood Processing EquipmentBoat and Marine Control PanelsMilitary Applications (Communication Switches)Medical Equipment (Wheelchair Motor Switch)Off-Highway and Construction EquipmentSecurity Systems and Metal Detectors Ⅶ How to Wire a Toggle Switch Step 1Using a test light, locate a fused line as close to the intended location for the toggle switch as practicable. Step 2Install the toggle switch. You can utilize a switch panel for this or drill a hole through which the switch will be mounted. Check your switch; this hole should be 1/2 inch in most cases, but some switches require a larger opening. Step 3Connect a wire from the fused source to the toggle switch's center terminal. Insulated solderless connectors should be used to connect to the switch. How to Wire a Toggle Switch Connect another wire from the switch's second terminal to the device being controlled by the switch. There is no need to run a second wire for ground because vehicles and trucks use the body as the ground side of the circuit. Ⅷ How to Install a Toggle Switch8.1 Installing a Switch in Your Device's PanelStep 1: Before you begin, turn off all power to the device. Before beginning work on your equipment, as with practically all sorts of electrical repair, make sure there is no risk of electric shock. Attempting to change a "live" device is a sure way to injure yourself or produce a short circuit that will permanently ruin your device. *The exact method for detaching your device from its power supply varies based on the device. Disconnect the negative terminal of the battery, for example, in a car, whilst other gadgets may require you to unplug or physically disconnect the power source in some other method. Step 2: Remove the device's panel or casing. To install a toggle switch on a device, you must first obtain access to the item's internal wiring, which normally necessitates the removal of the device's outside paneling or enclosure. Instead of removing the paneling from the entire object, try to remove it solely from the section of the gadget where you plan to place the switch. *For example, if you're putting a toggle switch in your car, you should remove a tiny section of the dash paneling where you wish to install the switch rather than the full dash panel. *Screwdrivers, pry bars, "panel poppers," and other specialist tools may be required. Step 3: The diameter of the switch bushing that will protrude through the panel should be measured. To make room for your toggle switch, you'll normally need to cut a hole in the paneling or casing of your item. Measure the dimensions of the switch bushing (the part of the switch where the "lever" is situated) to determine the size of your hole. *A round hole is typically used for simple toggle switches, however depending on the type of switch, other shapes may be required. Step 4: To fit your hole, drill or cut a hole in the panel. Next, drill a hole in your device's paneling to accommodate your switch. This means drilling with a bit slightly larger than the diameter of the switch bushing for the most basic toggle switches with circular bushings. You may need to use a jigsaw, sandpaper, and/or other equipment to create different-shaped holes. *To drill into wood, plastic, or mild steel, use an HSS (high-speed steel) twist drill bit. If you are drilling through wood, you can also use a spade bit. Step 5: Install the switch from the panel's underside. Finally, insert your switch into the hole you have made for it from the underside. With its mount, secure the toggle switch in place. This normally entails placing the mount over the hole, inserting the toggle switch, and securing it with a nut. *In a basic toggle switch configuration, for example, you may need to thread a jam nut onto the switch's bushing to secure it to the panel mount, then tighten the nut with an adjustable wrench. 8.2 Connecting Your Toggle Switch to Your Device's WiringStep 1: Follow the instructions that came with your switch or device. The electrical setups of the devices on which you would want to put a toggle switch will vary substantially. As a result, no single guide is likely to offer a one-size-fits-all solution. The instructions in this section are intended to serve as general guidelines for constructing a simple on-off ((single pole, single throw or SPST) toggle switch. They should never take precedence over any instructions contained with your toggle switch or the device into which it is being installed. *To save time and avoid unintended damage, call a trained electrician when in doubt. Step 2: Remove the power supply line from your gadget. You must connect your toggle switch to the device's power supply in order for it to act as an on/off switch. Use wire cutters to cut the supply wire of your device at a spot that allows you to route either or both ends of the wire to the switch. Using a wire stripper, remove roughly 12 inch (1.3 cm) of insulation from each end of the wire. Step 3: If neither end of the cable reaches the switch, use a pigtail. A pigtail is a short length of wire with both ends stripped (typically approximately 6 inches (15 cm)). As a sort of "extender," it can be linked to cables that aren't quite long enough to reach your toggle switch. Add a pigtail like this: *Find a wire of the same color and gauge as the present wire. *Cut a length of wire long enough to reach from the supply wire's cut end to the toggle switch. *Remove 12 inch (1.3 cm) of insulation from either end of this wire. *Connect one end of the pigtail wire to the supply wire by twisting the wire ends clockwise together. Twist a wire nut of the appropriate size clockwise over the wire joint until it is snug. Step 4: Connect the power supply to the toggle switch. You've built a break in the device's supply line at this point, so you'll need to install your toggle switch in the middle of the break to regulate the flow of energy through the circuit. The method you use is determined by the sort of toggle switch you have. Please see the following: *If your toggle switch includes wire leads, twist the end of each lead to one of the supply wires (or pigtail extensions) and tighten each wire connection with a wire nut. *If your toggle switch has screw terminals, unscrew the terminal screws, loop the supply wire ends, and hook each loop over a terminal screw so that the loops point clockwise around the shaft of each terminal screw. The terminal screws should then be tightened. *If the toggle switch is soldered, wrap the wire ends around the switch terminals. Needle-nose pliers could come in handy. While holding the end of the solder wire in contact with the terminal, heat each terminal with a soldering iron (but not in direct contact with the soldering iron tip). Withdraw the soldering iron tip when the solder begins to melt, allowing the melting solder to flow and cover the wire-terminal connection. Step 5: Check your switch. When your toggle switch is properly wired, carefully reconnect the device's power supply and test the toggle switch's functionality. If everything functions as it should, you can replace the panel or device housing. Congratulations! You have now installed a toggle switch. Ⅸ Precautions for the Use of the Toggle Switch1. If a load is supplied to the toggle switch terminals while soldering, there may be loosening, distortion, and deterioration of electrical properties due to various situations. Please use it with caution. 2. Because the effects of thermal stress alter when utilizing through-hole printed circuit boards and non-recommended circuit boards, please thoroughly confirm the soldering circumstances ahead of time. 3. Welding twice should be done when the first welding part has returned to normal temperature. Continuous heating can deform the perimeter, loosen terminals, cause them to fall off, and degrade electrical properties. 4. It is vital to confirm the actual mass production conditions while setting welding conditions. 5. The product is developed and manufactured with a DC resistance load in mind. Please confirm individually when employing different loads [inductive load, capacitive load]. 6. Please refer to the suggested dimensions indicated in the product drawing for the mounting holes and patterns of the printed circuit board. 7. The switch should be utilized in structures where the switch is operated directly by humans. It should not be used for mechanical detection. 8. When operating the toggle switch, if a load more than the specified amount is applied, the switch may be damaged. Take cautious not to apply more force to the switch than is specified. 9. Please refrain from touching the operational portion from the side. 10. For the flat shaft rod type, press the switch center as hard as possible. Please keep in mind that the pressing location of the shaft will move when the hinge structure is pressed. 11. After installing the switch, please consult a professional when going through the regenerative hardening furnace due to the hardening of other components' adhesive. 12. If corrosive gas is formed from the surrounding materials of the entire machine when using the switch, it may cause problems such as poor contact, so please confirm thoroughly in advance. 13. The carbon contact point has the property that the contact resistance changes as the pressing load changes. Please utilize it after adequate confirmation when employed in a voltage divider circuit, for example. 14. Be aware of the infiltration of alien stuff in models other than the contained type. Ⅹ Frequently Asked Questions About Toggle Switches1. Is a toggle switch an analogue or digital?A toggle switch is an analog device that cannot generate digital signals. When used as an input with a device such as a microcontroller, it can generate digital signals that the microcontroller can interpret as 1's and 0's. 2. Where would you use a toggle switch?Toggle switches are ideal for modifying the state of system functionalities and preferences. To allow users to choose between two opposed states, toggles can substitute two radio buttons or a single checkbox. It can be difficult to decide which user interface element to employ — radio buttons, checkboxes, or toggles — at times. 3. What is toggle switch used for?The toggle switch is a type of electrical switch distinguished by the presence of a handle or lever that allows the flow of electric current/signal from a power supply to a device or within a device to be controlled. It is a hinged switch that may be set to one of two states: ON or OFF. 4. How do you wire a push button toggle switch?Toggle Switch(1)Drill a hole in the desired area for the switch.(2)Push the switch wire into the hole and connect it to the vehicle's power supply wire with a terminal connector.(3)Using the nut that came with the switch, secure the switch to the hole. 5. How do you start a car with a toggle switch?To begin, crank the ignition key to unlock the steering wheel and the transmission gear shift lock. To start the engine, press the ignition switch. If the starter switch is not spring-loaded, it should be turned off as soon as the engine begins, or the starter will remain engaged. 6. How do you wire a SPST to a toggle switch?(1)Begin by crimping the wire terminals on the wire run you'll be using for the circuit.(2)After that, connect the power wire to the switch's center terminal.(3)After that, connect the wires for your accessory to the top terminal on your switch. 7. What does a toggle light switch look like?The typical toggle switch fits into a small rectangular space in wall plates; switches flick up and down to turn on and off lights. Although most of us are familiar with basic toggle switches, there are a few different types of toggle switches available for toggle switch plates and other plate apertures. 8. What is the difference between button and a toggle switch?Designers frequently confuse toggle switches with toggle buttons because they both control states, but there is a significant distinction. Toggle switches represent system states, while toggle buttons represent contextual states. A switch is a "button" that activates the condition. 9. What is a toggle switch in a circuit?Toggle switches are a form of electronic switch, and they are one of the most fundamental and commonly used electrical components. Electronic switches enable binary on-off control for electrical circuits by halting or resuming current flow. Toggle switches are actuators, which turn a machine on or off. 10. Is a toggle a button?A toggle button allows the user to switch between two states of a setting. Android 4.0 (API level 14) features a new type of toggle button called a switch, which has a slider control and can be added with a Switch object. 11. Can you use a toggle switch as a light switch?The typical toggle switch fits into a small rectangular space in wall plates; switches flick up and down to turn on and off lights. Available in 15A and 20A models, as well as single pole, 3-way, and 4-way configurations. Purchase toggle switches or toggle light switch covers. 12. What is momentary toggle switch?The Greengate Lighting Control Panels feature the Momentary Toggle Switch, which is a low voltage contact closure switch. When toggled up or down, the switch sends a "On" signal to the lighting control panel for a brief period of time and has a center "Off" position. 
kynix On 2022-05-13   2291
Resistors

What is a Motion Sensor?

 CatalogIntroduction of Motion SensorRelated VideoTypes of Motion SensorsⅠ Active Motion SensorsⅡ Passive Motion SensorsHow Do Smart Motion Sensors Work?Pros and ConsA DIY GuideFAQIntroduction of Motion SensorA motion sensor or motion detector is an electronic device that uses sensors to detect nearby human beings or objects. Unlike many other types of sensors, motion sensors are typically embedded systems consisting of three main components: a sensor unit, an embedded computer, and hardware (or consisting of mechanical components). When the motion sensor detects a moving object, it will perform data analysis and data comparison in the system, and send an alarm message to your mobile device through the Internet, so that you will know immediately if there is a security problem in the detection area. In addition, if you subscribe to a merchant's monitoring service, you can even set up motion sensors to automatically send alerts to the monitoring team. Related VideoVideo: Motion Sensors as Fast As PossibleVideo Description:Motion sensors have changed pretty significantly in the last 20 years. We even have sensors that detect their own motion! Wait... how does that work? Types of Motion SensorsActive motion sensors and passive motion sensors are two types of motion sensors. Ⅰ Active Motion SensorsIn a specific region or area, active motion sensors continuously emit energy in the form of infrared light or an electrical field. When people or objects with heat or temperature pass through this area, they cause temperature disturbances that can be detected by the motion sensor.Active motion sensors include both emitter and reflection detection circuits, but they use more energy than passive motion detectors. Active motion detectors are classified into three types: microwave, tomographic, and ultrasonic.Microwave SensorsThese sensors generate microwave pulses and then calculate their reflection off of objects to determine whether or not the objects are moving. Microwave sensors are extremely sensitive; the frequency at which the waves emitted differs if the waves are reflected by any moving object. However, these can sometimes be seen in nonmetallic objects that can be detected moving objects outside of the target range. Because it consumes a significant amount of power, these sensors are frequently designed to cycle ON and OFF. If you understand the cycles, you can acquire past them. Microwave sensors are used in electronic guard dogs. Tomographic SensorsWhen waves goes wrong, these sensors generate radio waves and detect them. They can see through walls and objects and are frequently embedded in a network of radio waves capable of covering large areas. Because these sensors are expensive, they are commonly used in warehouses, storage units, and other commercial-level security situations. Because these sensors do not require line of sight, they can detect movement in concealed areas up to 5,000 square feet high. When a disturbance in the grid network is detected, the sensor activates the motion sensor alarm. Ultrasonic SensorsUltrasonic sensors can be active (or) passive, with passive ones listening for specific sounds such as metal on metal or glass breaking. These sensors are extremely sensitive, but they are often prohibitively expensive and prone to false alarms. Active ones generate ultrasonic wave (sound wave) pulses and then determine how these waves are reflected off a moving object. Animals such as cats, dogs, and fish can hear these sound waves, so an active ultrasonic alarm could startle them. An ultrasonic detector, in theory, emits high-frequency sound waves that are reflected back to the sensor. If the sound waves are interrupted, the active ultrasonic sensor may sound an alarm. Ⅱ Passive Motion SensorsPassive motion sensors are opposite to active sensors in that they do not emit anything but simply detect infrared energy. Passive detectors detect infrared (heat) energy levels. Passive sensors scan the room or area, looking for infrared heat emitted by living beings.Passive Infrared Sensor (PIR)The PIR sensor is a pyroelectric sensor that is divided into two halves so that whenever a moving object emits infrared radiation, each half cancels the other half if both halves have the same IR radiation – then the sensors do not sense – but if it finds any more or less IR radiation, the PIR sensor senses. There are various PIR sensors available with varying coverage areas.Because the PIR Motion detector is easily obstructed by the variability of heat sources and sunlight, it is better suited for indoor movement detection within a closed environment. Dual-technology Motion SensorsIn addition to active and passive sensors, the progress of motion sensor technology has also developed dual-technology sensors, that is, combining different motion sensor technology to develop motion sensors, reducing the false trigger sensor. The early motion sensors discussed in this article can fail in certain situations, such as the PIR sensor that can be incorrectly activated by changes in heat and light without the object actually moving. Similarly, if something causes the sensor to activate motion, the microwave sensor can also be activated incorrectly. Therefore, in order to avoid these disadvantages, we can combine sensors, such as PIR and microwave sensors to improve efficiency. Here, by using two sensors at the same time, even the PIR sensor can be activated by changes in heat or light without involving object motion, but the microwave sensor can't be activated, so the motion sensor switch can't be activated either. Similarly, the motion sensor switch cannot be activated by the combined sensor even if the passive arm of the microwave sensor is activated and the PIR sensor is not. How Do Smart Motion Sensors Work?The majority of smart motion sensors employ passive infrared (PIR) technology. PIR sensors detect infrared energy emitted by humans and other animals as body heat. As a result, if the temperature suddenly rises, your device will detect it and notify your system's control panel. PIR sensors can be programmed to ignore minor temperature changes, so you don't have to worry about your pets accidentally setting off alarms. Motion sensors can be used to turn on a light when someone approaches your home, to sound an alarm when movement is detected in your living room, or to trigger a motion sensor camera to begin recording when someone enters your home. Pros and ConsPros of motion sensor:The following are the benefits of active and passive motion sensors:1.It is suitable for use in harsh environments with irregular heat cycles (Active Motion Sensor).2.It has a longer lifespan of approximately 100000 hours (Active type).3.It reliably detects motion in both light and dark conditions indoors. (Sensor of Passive Motion)4.It contributes to security by detecting suspicious movement.5.Motion sensors are simple to install. Cons of motion sensor:The following are the drawbacks of active and passive motion sensors:1.High-powered radio frequency is hazardous to humans (active type).2.Microwave radio frequencies do not penetrate metal objects (active type).3.Passive motion sensors do not work above 350 degrees Celsius.4.Passive sensors only work in LOS (Line of Sight) areas and do not work in non-LOS areas.5.The passive type is unaffected by very slow object motion.6.The Passive Infrared (PIR) Sensor can detect humans within a 10 meter range.7.The PIR sensor type can be triggered by any moving object. A DIY Guide A guide for your DIY sensor system:If you want to do your own security, make sure to follow the instructions that come with the sensor. Here are some pointers for installing motion detectors in your home or business: Install sensors near entrances. Motion detectors designed specifically for doors and windows are available. Set them up in high-traffic areas. Installing the sensor in a hallway, stairwell, or other area where people must pass through increases the likelihood of catching an intruder. It's also a good idea to put sensors in rooms with particularly valuable items, where thieves are likely to go first. Install PIR sensors away from heat sources. PIR sensors analyze temperature fluctuations in a given area and can cause a false alarm if installed too close to a vent, furnace, or fireplace. Don't obstruct the sensor. If the sensors are obstructed, they will not function properly. An impediment may not be obvious at first. For example, if you install a motion sensor light above your driveway, your parked car may interfere with its ability to detect motion on the sidewalk or in the street. Install the sensor in an area where there is no obstruction. Wipe the sensor clean after installation to ensure an unobstructed lens, and remember to clean it on a regular basis after that. FAQ1.Should I have motion sensor lights installed in my home?Indoor motion detector lights are less common than outdoor motion detector lights, but they do exist. These are typically LED models that are energy-efficient and designed to illuminate garages, workspaces, or dark hallways. They can also be used to install in-home entryways, eliminating the need to fumble around for the light switch when you arrive home at night. 2.What is a smart motion sensor?Smart motion sensors detect movement in and around your home and initiate an action in response. When a smart motion sensor detects you entering a room, it can automatically turn on the lights. Alternatively, they can send you an alert if an intruder attempts to enter your home. Finally, the goal of motion sensors is to provide peace of mind while also making your home run more smoothly and efficiently. 3.What is a PIR Sensor?The PIR is a motion sensor with a white cover that you may have seen when entering a restroom or an office space. They are small, low-power, simple to operate, and inexpensive. It detects movement by detecting temperature differences between the background and a warm body. 4.How microwave sensors work?Microwave sensors detect motion by using continuous waves of microwave radiation, similar to how a radar speed gun works. It sends out a high radio frequency and detects a frequency shift to measure the reflection off an object. If a frequency shift is detected, the motion detector is activated. 5.How do you reset an outdoor motion sensor light?Turning off and back on for 30 seconds or longer is the best way to reset a motion sensor light. A homeowner can also turn off the power to it at the breaker to give it time to reset itself. If that doesn't work, the sensor or the bulb may be at fault. 6.Can you add a motion sensor to an existing light?For both residential and commercial lighting, a motion sensor adds safety, security, and convenience. If an existing light is in good working order, adding a light sensor does not necessitate replacing it. Rather, use a motion sensor adapter to convert existing lights to motion sensor lights. 7.How do you adjust a motion sensor switch?Users can change the settings of the motion sensor light switch by switching toggles under the cover or pressing buttons on the surface. Auxiliary buttons or toggles behind the cover plate are used to program many of the classic motion sensor light switches. 8.How to fix a motion sensor light?Turning off and back on for 30 seconds or longer is the best way to reset a motion sensor light. 9.Why is motion sensor lighting a good investment?Installing a motion detector light is a simple task that is well suited to the homeowner who is willing to put a few minutes into improving their home. The task depicted in the photos here, showing the replacement of a defective light, took only about 15 minutes and no special tools. 10.Where are motion sensors used?A motion sensor (or motion detector) is a type of electronic device that detects and measures movement. Motion sensors are most commonly found in home and business security systems, but they are also found in phones, paper towel dispensers, game consoles, and virtual reality systems. 
kynix On 2022-05-09   1991
Transistors

Transistor Working Regions and Switch Circuit Characteristics

Executive Summary: Transistors in 2026The semiconductor transistor remains the fundamental building block of modern electronics. As of January 2026, the industry has shifted toward Gate-All-Around (GAAFET) architectures at the 2nm process node, enabling AI chips like NVIDIA's Blackwell B200 to pack over 208 billion transistors. This guide updates legacy concepts with 2026 standards, covering operation modes, NPN/PNP switching circuits, and the latest market statistics approaching a $1 Trillion valuation.What is a Semiconductor Transistor in 2026?A semiconductor transistor is an active semiconductor device used to amplify, control, and generate electrical signals and power. It functions as a variable current switch capable of controlling output current based on input voltage. Unlike ordinary mechanical switches (such as relays), transistors use electrical signals to control their own opening and closing, allowing for switching speeds in the gigahertz (GHz) range—critical for modern 5G and AI applications.Key 2026 Insight: While traditional Bipolar Junction Transistors (BJTs) are still used in analog circuits, modern high-speed computing relies on GAAFET (Gate-All-Around Field Effect Transistor) technology, which has replaced FinFET at the 3nm and 2nm nodes to minimize power leakage.Video: Transistors Basics Explained Ⅰ How do Electrons and Holes Function in a Transistor?The transistor is a current-controlled device (BJT) or voltage-controlled device (FET) that facilitates signal amplification, oscillation, and modulation. Its operation relies on the movement of charge carriers: electrons (negative charge) and holes (positive charge carriers).A standard BJT has three terminals (Emitter, Base, Collector), three regions, and two PN junctions. Understanding the internal structure is key to grasping how 2026 hardware manages billions of switching operations per second.Figure 1. Transistor Structure (NPN Configuration)Movement of Charge Carriers:Figure 2. Movement of Charge CarriersHoles vs. Electrons: The hollow circles in Figure 2 represent positively charged holes, while solid dots are negatively charged electrons. "Hole movement" is effectively the macroscopic result of electrons filling vacancies.Emitter (E): Heavily doped to emit a large number of electrons. When forward-biased, it injects carriers into the base.Base (B): Very thin and lightly doped. In an NPN transistor, the P-type base allows most electrons from the emitter to diffuse directly to the collector, with very few recombining with holes (creating the small base current, IB).Collector (C): Large surface area designed to collect electrons drifting through the base. It dissipates the most heat, especially in power transistors used in 2026 EV inverters.Current Equation: IE (Emitter Current) = IC (Collector Current) + IB (Base Current).Ⅱ What are the Key Characteristics of Transistors?Transistors define the logic of all digital circuits. Their behavior is governed by the following core principles:1) Current Control (BJT): The small base current (IB) controls the large collector current (IC).NPN Current Direction: Base → Emitter.PNP Current Direction: Emitter → Base.2) Amplification Factor (β): Transistors amplify signals by a factor of β (Beta). If IB = 1mA and β = 100, then IC = 100mA. This principle amplifies weak sensor signals in IoT devices.3) Saturation (Switch ON): When IB is sufficient (e.g., ≥1mA for small signal transistors), the voltage drop Vce ≈ 0.3V. The transistor acts as a closed switch.4) Cutoff (Switch OFF): When Vbe < 0.7V (for Silicon), the transistor is fully off. Vce is high (equal to supply voltage), acting as an open switch.Design Tip for 2026: For NPN switching circuits, connect the load to the Collector and the Emitter to Ground (GND). For PNP, connect the Emitter to Power (VCC) and the load to the Collector. NPN is generally preferred in modern logic due to higher electron mobility compared to hole mobility. Ⅲ What are the Three Operational Regions of a Transistor?To effectively use a transistor in AI hardware or power regulators, one must understand its three operational states: Cut-off, Active, and Saturation.Figure 3. Transistor Circuit And Operational Regions(1) Cut-off Region (Digital "0"): The transistor is OFF. Ube < Threshold (0.7V). IB = 0, IC ≈ 0. The switch is open.(2) Active Region (Amplification): Used for analog signal processing (audio, radio). The Emitter junction is forward-biased, and the Collector junction is reverse-biased. IC = β * IB.(3) Saturation Region (Digital "1"): The transistor is fully ON. Both junctions are forward-biased. IC cannot increase further even if IB increases. Uce is minimal (~0.2V).In embedded systems and logic gates (like those in the newest 2nm chips), transistors toggle rapidly between Cut-off and Saturation, avoiding the Active region to minimize power loss.Figure 4. Voltage CharacteristicⅣ How to Analyze Input and Output Characteristics?4.1 Input CharacteristicsThe input characteristic curve relates the base current (IB) to the base-emitter voltage (VBE). It resembles the curve of a standard diode.Figure 5. Input CharacteristicWhen VCE increases, the collector's ability to "sweep" electrons improves, slightly reducing the recombination in the base. This shifts the curve to the right, meaning less IB flows for the same VBE.4.2 Output CharacteristicsThe output characteristic relates the collector current (IC) to the collector-emitter voltage (VCE) for various fixed values of IB.Figure 6. Output CharacteristicUnderstanding the Graph: The horizontal axis is VCE. The initial steep rise is the Saturation Region (switch closed). The flat horizontal lines represent the Active/Amplification Region, where IC is constant regardless of VCE (acting as a constant current source controlled by IB). Ⅴ What Causes Saturation and Cutoff Distortion?Signal distortion occurs when a transistor amplifier is improperly biased, causing the output waveform to be "clipped" at the top or bottom.5.1 Waveform Analysis of Basic Common Emitter Amplifier CircuitFigure 7. Waveform Analysis of Common-emitter Amplifier CircuitSaturation Distortion (Bottom Clipping): Occurs when the static operating point (Q-point) is too high. IB is too large, causing UCE to drop near 0V during the positive half-cycle of the input.Cutoff Distortion (Top Clipping): Occurs when the Q-point is too low. IB is too small, causing the transistor to turn OFF during the negative half-cycle of the input.5.2 Why use Transistors as Switches?Feasibility: The distinct "ON" (Saturation) and "OFF" (Cutoff) states allow transistors to replace mechanical switches. Modern SiC (Silicon Carbide) transistors can switch high voltages in EVs with minimal efficiency loss.Necessity: Microcontrollers (CPUs/MCUs) operate at low voltages (3.3V or 5V) and cannot directly drive high-power loads like motors or LED arrays. A transistor acts as the bridge, allowing a weak software signal to control massive power. Ⅵ How to Design Transistor Switching Circuits?6.1 Basic Switching Circuit of NPN TransistorsFigure 8. NPN Transistor Switch CircuitLow-Side Switching: In an NPN circuit, the Load (R1) is connected between VCC and the Collector. The Emitter connects to Ground. When the Base receives a High signal (e.g., 3.3V from a GPIO pin), current flows from C to E, turning the load ON.6.2 Basic Switching Circuit of PNP TransistorsFigure 9. Basic Switching Circuit of PNP TransistorHigh-Side Switching: Common PNP models like the 8550 are used here. The Emitter connects to VCC. The Load connects between the Collector and Ground. Logic: A LOW signal (0V) at the Base turns the PNP transistor ON. A HIGH signal turns it OFF. This is often used for driving buzzers or indicators where the ground path must remain common. Ⅶ Frequently Asked Questions About Transistors (2026 Update)1. How does a semiconductor transistor work?A transistor works by using a small control current at the Base (or voltage at the Gate) to regulate a much larger current flowing between the Collector and Emitter (or Source and Drain). This allows it to act as an amplifier or a high-speed electronic switch.2. How is a transistor used as a switch?The transistor operates as a solid-state switch by toggling between the Cutoff region (Open circuit, OFF) and the Saturation region (Short circuit, ON). It eliminates moving parts, allowing for billions of operations per second in modern CPUs.3. What is the PN junction of a transistor?A BJT contains two PN junctions. The Emitter-Base junction is forward-biased to inject carriers, while the Collector-Base junction is typically reverse-biased to collect them. These junctions form the potential barriers that control current flow.4. How many PN junctions are there in a transistor?2 PN JunctionsA Bipolar Junction Transistor (BJT) has two PN junctions (Base-Emitter and Base-Collector). Field Effect Transistors (FETs) rely on channel conductivity rather than junction injection.5. What are the two basic types of transistors?The two primary categories are Bipolar Junction Transistors (BJT) (current-controlled) and Field Effect Transistors (FET) (voltage-controlled). As of 2026, FETs (specifically MOSFETs and GAAFETs) dominate digital electronics.6. What are the terminals of a transistor called?For BJTs: Emitter, Base, and Collector. For FETs/MOSFETs: Source, Gate, and Drain.7. What is the difference between NPN and PNP?An NPN transistor turns ON with a positive current to the Base (High-Side control usually requires voltage > Emitter). A PNP transistor turns ON when the Base is pulled Low (voltage < Emitter). NPN is more common in switching applications due to better electron mobility.8. What is the most popular transistor in 2026?The MOSFET remains the most widely used transistor globally, accounting for 99.9% of all transistors. However, for cutting-edge AI chips (like NVIDIA Blackwell), GAAFET (Gate-All-Around) is the new standard, while SiC and GaN dominate power electronics in electric vehicles.{ "@context": "https://schema.org", "@type": "Article", "headline": "What is a Semiconductor Transistor? 2026 Comprehensive Guide", "datePublished": "2019-01-01", "dateModified": "2026-01-05", "description": "A deep dive into semiconductor transistors, covering electrons/holes, NPN/PNP characteristics, and 2026 industry standards like GAAFET and AI chip architectures.", "author": { "@type": "Organization", "name": "Kynix Semiconductor" }, "mainEntity": { "@type": "FAQPage", "mainEntity": [ { "@type": "Question", "name": "How does a semiconductor transistor work?", "acceptedAnswer": { "@type": "Answer", "text": "A transistor works by using a small control current at the Base (or voltage at the Gate) to regulate a much larger current flowing between the Collector and Emitter, effectively acting as an amplifier or switch." } }, { "@type": "Question", "name": "What are the two basic types of transistors?", "acceptedAnswer": { "@type": "Answer", "text": "The two main types are Bipolar Junction Transistors (BJT) and Field Effect Transistors (FET). In 2026, FETs (specifically MOSFETs and GAAFETs) are the dominant technology for digital processors." } }, { "@type": "Question", "name": "How acts a transistor as a switch?", "acceptedAnswer": { "@type": "Answer", "text": "It acts as a switch by driving the transistor into saturation (fully ON) or cutoff (fully OFF), thereby completing or breaking the circuit path for the load." } }, { "@type": "Question", "name": "What is the difference between NPN and PNP transistors?", "acceptedAnswer": { "@type": "Answer", "text": "NPN transistors are 'active high' switches that turn on when current enters the base. PNP transistors are 'active low' switches that turn on when the base is pulled to ground." } } ] }}
Kynix On 2022-03-10   3249
Mosfets

Difference and Relation Between IGBTs and MOSFETs

Introduction IGBT and MOSFET are fully controlled devices and are voltage-driven, that is, the device is turned on or off by controlling the gate voltage. In fact, the structure of the IGBT is an NPN-type MOSFET plus a P-junction, that is, an NPNP structure, which is a P-type BJT driven by MOS in principle. So what is the difference between them? What is the specific connection of them? MOSFET BJT or IGBT - Brief Comparison Catalog Introduction Ⅰ MOSFET & IGBT Review Ⅱ Si IGBT vs SiC MOSFET Ⅲ Different Requirements for Si IGBT and SiC MOSFET 3.1 ON & OFF State 3.2 Short-Circuit Protection 3.3 Interference and Delay Ⅳ IGBT Working Principle by Analogy with MOSFET Ⅴ FAQ Ⅰ MOSFET & IGBT Review MOSFET is a metal-oxide-semiconductor field effect transistor, or metal-insulator-semiconductor. The source and drain of it can be swapped, and they are both N-type regions formed in the P-type backgate. In most cases, these two regions are the same, even if the two ends are reversed, it will not affect the performance of the device. Such devices are considered symmetrical. According to the polarity of its "channel" (working carrier), MOSFET can be divided into two types: N-type and P-type, usually also called NMOSFET and PMOSFET, abbreviations including NMOS, PMOS, etc.IGBT (insulated gate bipolar transistor), is a composite fully controlled voltage-driven power semiconductor device composed of BJT (bipolar transistor) and MOS. Have the advantages of high input impedance of MOSFET and the low on-voltage drop of the GTR. When the GTR saturation voltage is reduced, the current carrying density is large, but the driving current is large; the MOSFET driving power is small, the switching speed is fast, but the on-state voltage drop is large, and the current carrying density is small. The IGBT combines the advantages of the above two devices, and the driving power is small and the saturation voltage is reduced. In simple terms, an IGBT is equivalent to a thick base PNP transistor driven by a MOS. Figure 1. N-MOSFET Architecture Ⅱ Si IGBT vs SiC MOSFET Since the differences between IGBT and MOSFET in structure, working principle and application range are quite detailed, it is impossible to express clearly in one sentence. Next, we will compare the differences between silicon (Si) IGBTs and silicon carbide (SiC) MOSFETs in detail.The electrical parameters and characteristics of Si IGBT and SiC MOS drivers are quite different. The requirements for driving of SiC MOS are also different from those of traditional silicon devices. They have the characteristics of low on-resistance and small switching loss, which can reduce device loss and improve system efficiency, and more suitable for high frequency circuits. It is widely used in new energy vehicle motor controller, vehicle power supply, solar inverter, charging pile, UPS, PFC power supply and other fields.The difference between the two is mainly reflected in the GS turn-on voltage, GS turn-off voltage, short-circuit protection, signal delay and anti-interference, as follows: Characteristic Si IGBT SiC MOSFET Drive Requirements Switching Frequency Low, >30kHz High, 50~500kHz 1) Use high power gate resistors. 2) Optimize the cooling environment. 3) Improve the efficiency of the DC-DC conversion circuit and reduce the overall loss of driving power. Threshold Voltage 5V-6V 1.6V-4.5V Negative pressure shutdown/Miller clamp to prevent false turn-on Switching Time 300ns 50ns 1) Use digital isolation driver chip, the signal transmission delay can reach 50ns, and it has relatively high consistency, and the transmission jitter is less than 5ns. 2) the low transmission delay push-pull chip is selected. Switching-On Time 15V 15V~22V 1) Priority is given to stabilizing the negative voltage to ensure that the shutdown voltage is stable. 2) A negative voltage clamping circuit is added to ensure that it does not exceed the standard during shutdown. Switching-Off voltage -15V~-5V -5V~0V Short-Circuit Withstand Time <10μs 2~5μs A diode or a resistor string is used to detect short circuits, and the shortest short-circuit protection time is limited to about 1.5μs. CMTI 15kV/μs 100kV/μs 1) The common mode anti-interference ability reaches 100kV/μs to transmit the isolation chip for signal transmission. 2) The optimized isolation transformer design is adopted, and its primary side and the secondary side are shielded to reduce mutual crosstalk. 3) The Miller clamp is used to prevent the influence of the switch of the same bridge arm.   Ⅲ Different Requirements for Si IGBT and SiC MOSFET For a fully-controlled switching device, configuring an appropriate on-off voltage is of great significance for the safety and reliability of the device. Due to the difference between IGBT and MOSFET, the requirements for the two are also different.IGBT is a field-controlled device whose turn-on and turn-off are determined by the voltage between the gate(G) and the emitter(E). The working principle of MOS tube (enhancement mode NMOSFET) is to use VGS to control the amount of "induced charges" to change the condition of the conductive channel, and then to control the drain current. 3.1 ON & OFF State 1) Silicon IGBT: Silicon IGBTs of various manufacturers have the same turn-on and turn-off voltage requirements.· The typical turn-on voltage is required to be 15V.· The shutdown voltage value range is -5V~-15V, and customers can choose the appropriate value according to their needs. The common values are -8V, -10V, -15V.· Prioritize stable positive voltage to ensure stable turn-on.2) Silicon carbide MOSFET: Different manufacturers have different switching voltage requirements:· The turn-on voltage is required to be higher than 22V~15V.· The shutdown voltage is required to be higher -5V~-3V.· Prioritize negative voltage stabilization to ensure stable turn-off voltage.· Increase the negative voltage clamping circuit to ensure that it does not exceed the standard when it is turned off. 3.2 Short-Circuit Protection The switching device has the risk of short circuit during operation, and configuring a suitable short circuit protection circuit can effectively reduce the damage caused by the short circuit during the use of the switching device. Compared to Si IGBTs, SiC MOSFETs have shorter short-circuit withstand times.1) Silicon IGBTThe time of surrender and short-circuit of Si IGBT is generally less than 10μs. When designing the short-circuit protection circuit of it, set the detection delay and corresponding time of short-circuit protection to 5-8μs.2) SiC MOSFETGenerally, the short-circuit withstand capability of SiC MOSFET modules is less than 5μs, and short-circuit protection is required to work within 3μs. A diode or a resistor string is used to detect short circuits, and the protection time is limited to about 1.5μs. 3.3 Interference and Delay 1) The impact of high dv/dt and di/dt on the system.When the switching action is performed under the condition of high voltage and high current, the switching of the silicon carbide MOSFET device will generate high dv/dt and di/dt, which will affect the driver circuit. It is very important to improve the anti-interference ability of the driver circuit for the reliable operation of the system. the following way to achieve.· Add common mode choke coil and filter inductor to the input power supply, which reduce the interference of driver EMI to low voltage power supply.· A low-pass filter is added to the rectification part of the secondary side power supply, which reduce the interference of the driver to the high-voltage side.· Use an isolation chip with a common mode immunity of 100kV/μs for signal transmission.· Optimize the isolation transformer design, and use shielding layer on primary side and secondary side to reduce crosstalk between each other.· Use Miller clamp to prevent the influence of the switch of the same bridge arm. 2) Low transmission delayUsually, the application switching frequency of silicon IGBT is less than 40kHZ, and the recommended application switching frequency of SiC MOSFET is greater than 100kHz. The increase of application frequency makes MOS require the driver to provide lower signal delay time. The transmission delay of the SiC MOSFET drive signal should be less than 200ns, and the transmission delay jitter should be less than 20ns, which can be achieved by the following methods.· Using digital isolation driver chip, the signal transmission delay can reach 50ns, and it has relatively high consistency, and the transmission jitter is less than 5ns.· Select push-pull chips with low transmission delay and short rise & fall time. Due to the conductance modulation effect, the on-state specific resistance of high voltage SiC IGBTs is much lower than that of power SiC MOSs, and does not change much as the blocking voltage rating increases. When the conductance modulation effect is fully exerted, the on-state voltage drop of the IGBT drift region is only related to the bipolar diffusion coefficient and bipolar lifetime of the carriers, and will not change with the increase of the on-current. When the operating temperature changes, the on-state voltage drop of the SiC high voltage IGBT decreases with the increase of the junction temperature. This is mainly because the bipolar lifetime of the extra carriers in the SiC epitaxial layer will increase with the increase of temperature. Although the diffusion coefficient will shrink to some extent with the increase of temperature, the greater prolongation of lifetime will eventually make the the bipolar diffusion length increased, thereby reducing the on-state voltage drop. It is especially true in n-channel devices.This is in sharp contrast to the larger increase in the forward voltage drop of the power MOS at high temperature. Silicon carbide p-channel IGBTs have higher on-state voltage drop than n-channel IGBTs at the same current density due to their larger channel resistance, but their volt-ampere characteristics do not change much with temperature. As for the applications, this is undoubtedly an advantage. Figure 2. Comparison of characteristics between SiC IGBT and power MOS under the Same Condition of Withstand Voltage of 20kV. It is not difficult to calculate from the intersection of the equal power consumption curve in the figure and the on-state characteristic curves of these devices: corresponding to the same power consumption of 300W/cm2, the ratio of the on-state current of the silicon carbide IGBT to the silicon carbide power MOS versus p-channel devices and n-channel devices are different, they are 1.5 and 1.8 at room temperature, respectively, and increase to 2.7 and 3.5 at 225°C, indicating that high-voltage and high-current SiC IGBTs are more suitable for high-temperature applications.In a word, compared with Si IGBT, SiC MOSFET not only improves system efficiency, power density and operating temperature, but also puts forward higher requirements for the driver. In order to make silicon carbide MOSFET better in the system, it is necessary to give SiC MOSFET a appropriate driver.   Ⅳ IGBT Working Principle by Analogy with MOSFET IGBT is a Darlington pair composed of GTR and MOSFET: part of which is MOSFET driver, and the other part is thick-base PNP transistor. Figure 3. IGBT Architecture Its simplified equivalent circuit is shown in the figure below, and RN in the figure is the modulation resistance in the base area of the PNP transistor. It can be clearly seen from this circuit that the IGBT is a composite device of Darlington configuration composed of transistors and MOSFET, where the transistor in the figure is a PNP transistor, and the MOSFET is an N-channel field effect transistor, so the IGBT of this structure is called an N-channel IGBT, and its symbol is N-IGBT. Similarly there are P-channel IGBTs, namely P-IGBTs. Figure 4. Simplified Equivalent Circuit The electrical graphic symbols of the IGBT are shown in the figure. IGBT is a field-controlled device, and its turn-on and turn-off are determined by the voltage UGE between the gate and the emitter. When the gate-emitter voltage UCE is positive and greater than the turn-on voltage UCE (th), a channel is formed in the MOSFET and is a PNP. The N-type transistor provides the base current to turn on the IGBT. At this time, the holes (minority carriers) injected into the N- region from the P+ region modulate the conductance of the N- region, reduce the resistance RN of the N- region, and make the IGBT also has a small on-state voltage drop. When no signal or reverse voltage is applied between the gate and emitter, the channel in the MOSFET disappears, the base current of the PNP transistor is cut off, and the IGBT is turned off. It can be seen that the driving principle of IGBT is basically the same as that of MOSFET.① When UCE is negative: J3 junction is in reverse bias state, and the device is in reverse blocking state.② When UCE is positive: UC< UTH, the channel cannot be formed, and the device is in a forward blocking state; UG> UTH, an N-channel is formed under the insulating gate, and conductance is generated in the N- region due to the interaction of carriers modulation so that the device is conducting forward. Figure 5. Hybrid Switch Using Si IGBT and SiC MOSFET 1) ONThe structure of IGBT silicon is very similar to that of power MOSFET, and the main difference is that JGBT adds a P+ substrate and an N+ buffer layer, in terms of it, one MOS drives two bipolar devices (devices with two polarities). The application of the substrate creates a J junction between the P, and N+ regions of the tube. When the positive gate bias causes the inversion of the P base region under the gate, an N-channel is formed, and an electron flow occurs at the same time, and a current is generated exactly in the manner of a power MOSFET. If the voltage produced by this electron flow is in the range of 0.7V, J1 will be forward biased, some holes will be injected into the N- region, and the resistivity between N- and N+ will be adjusted, which reduces the power conduction the total loss of the pass and initiates a second charge flow. The end result is the temporary emergence of two different current topologies within the semiconductor layer: an electron flow (MOSFET current), and a hole current (bipolar). When UCE is greater than the turn-on voltage UCE(th), a channel is formed in the MOSFET to provide base current for the transistor, and the IGBT is turned on. 2) On-State Voltage DropThe conductance modulation effect reduces the resistance RN and reduces the on-state voltage drop. The so-called on-state voltage drop refers to the tube voltage drop UDS when the IGBT enters the on-state, and this voltage decreases with the rise of UCS. 3) Shut DownWhen a negative bias is applied to the gate or the gate voltage is lower than the threshold value, the channel is disabled and no holes are injected into the N-region. In any case, if the current of the MOSFET decreases rapidly during the switching phase, the collector current decreases gradually. This is because there are still minority carriers in the N layer after the commutation starts. This reduction in residual current value (wake) is entirely dependent on the charge density at turn-off, which in turn is related to several factors, such as the number and topology of dopants, layer thickness and temperature. The decay of minority carriers makes the collector current have a wake waveform. Collector current will cause increased power dissipation and cross-conduction problems, especially on devices that use freewheeling diodes.Considering that the wake is related to the recombination of minority carriers, the current value of the wake should be closely related to the Tc, IC of the chip, and has a close relationship with the mobility of holes. Therefore, depending on the temperature reached, it is feasible to reduce the undesirable effects of this current on the end equipment design. When a back pressure or no signal is applied between the gate and the emitter, the channel in the MOS disappears, the base current of the transistor is cut off, and the IGBT is turned off. 4) Reverse BlockingWhen a reverse voltage is applied to the collector, the junction is reverse biased and the depletion layer expands to the N-region. Because the thickness of this layer is reduced too much, an effective blocking ability will not be obtained, so this mechanism is very important. In addition, if the size of this region is increased too much, the voltage drop will continuously increase. 5) Forward BlockingWhen the gate and emitter are shorted and a positive voltage is applied at the collector terminal, the junction is controlled by the reverse voltage. At this time, the depletion layer of the N drift region is still subjected to the externally applied voltage. 6) LatchICBT has a parasitic PNPN thyristor between the collector and the emitter. Under special conditions, this parasitic device will turn on. This phenomenon increases the amount of current between the collector and the emitter, reduces the controllability of the equivalent MOSFET, and often causes device breakdown problems. The thyristor turn-on phenomenon is known as IGBT latch-up. Specifically, the causes of such defects vary, but are closely related to the state of the devices.   Ⅴ FAQ 1. Are there SiC IGBT?Along with the increasing maturity for the material and process of the wide bandgap semiconductor silicon carbide (SiC), the insulated gate bipolar transistor (IGBT) representing the top level of power devices could be fabricated by SiC successfully. 2. Where are SiC MOSFETs used?The primary automotive applications for SiC power MOSFETs, diodes, and modules are onboard electric vehicle (EV) chargers, DC/DC converters, and drivetrain inverters. Plug-in hybrid EVs and battery EVs (BEVs) use onboard chargers to “refuel” the vehicle battery either at home or at a public charging station. 3. What is SiC MOSFET?Silicon Carbide (SiC) MOSFETs exhibit higher blocking voltage, lower on state resistance and higher thermal conductivity than their silicon counterparts. SiC MOSFETs are designed and essentially processed the same way as silicon MOSFETs. 4. Can MOSFET replace IGBT?Due to the higher usable current density of IGBTs, it can usually handle two to three times more current than a typical MOSFET it replaces. This means that a single IGBT device can replace multiple MOSFETs in parallel operation or any of the super-large single power MOSFETs that are available today. 5. What are the advantages of silicon carbide?Silicon carbide MOSFETs have a critical breakdown strength that is 10x of silicon, and silicon carbide MOSFETs can operate at much higher temperatures, provide higher current density, experience reduced switching losses, and support higher switching frequencies. 6. What are the advantages of silicon carbide (SiC) over silicon (Si)?The advantage of SiC starts in the material itself having a 10x higher dielectric breakdown field strength, 2x higher electron saturation velocity, 3x higher energy bad gap and 3x higher thermal conductivity than Silicon. 7. What is the difference between silicon and silicon carbide?Silicon has a breakdown voltage of around 600V, while silicon carbide can withstand voltages 5-10 times higher. ... Silicon carbide can switch at nearly ten times the rate of silicon, which results in smaller control circuitry. 8. What is SiC in semiconductor?SiC (silicon carbide) is a compound semiconductor composed of silicon and carbide. SiC provides a number of advantages over silicon, including 10x the breakdown electric field strength, 3x the band gap, and enabling a wider range of p- and n-type control required for device construction. 9. Which is better MOSFET or IGBT?When compared to the IGBT, a power MOSFET has the advantages of higher commutation speed and greater efficiency during operation at low voltages. What's more, it can sustain a high blocking voltage and maintain a high current. ... The IGBT is also a three terminal (gate, collector, and emitter) full-controlled switch. 10. Why use an IGBT instead of a MOSFET?The main advantages of IGBT over a Power MOSFET and a BJT are: 1. It has a very low on-state voltage drop due to conductivity modulation and has superior on-state current density. ... It canbe easily controlled as compared to current controlled devices (thyristor, BJT) in high voltage and high current applications. 11. Why is MOSFET preferred?Mosfet provides a very good isolation between the gate and the other two terminals compared to bjt. Mosfet can handle more power compared to BJT. The mosfet has a very low power loss and a high speed. Voltage signals can easily operate a mosfet, so it is used in many digital circuits. 12. Where are MOSFETs used?Power MOSFETs are commonly used in automotive electronics, particularly as switching devices in electronic control units, and as power converters in modern electric vehicles. The insulated-gate bipolar transistor (IGBT), a hybrid MOS-bipolar transistor, is also used for a wide variety of applications. 13. Why IGBT is very popular nowadays?With its lower on-state resistance and conduction losses as well as its ability to switch high voltages at high frequencies without damage makes the Insulated Gate Bipolar Transistor ideal for driving inductive loads such as coil windings, electromagnets and DC motors. 14. How many terminals are in a MOSFET?four terminalsThe MOSFET has four terminals: drain, source, gate, and body or substrate. 15. Why is IGBT bipolar?IGBTs is a bipolar device that utilizes two types of carriers, electrons and holes, resulting from the complex configuration that features a MOSFET structure at the input block and bipolar output, making it a transistor that can achieve low saturation voltage (similar to low ON resistance MOSFETs) with relatively fast. 16. How many types of IGBT are there?two typesInsulated Gate Bipolar Junction Transistor (IGBTs) are normally classified into two types. (ii) Punch Through [PT-IGBT]. These IGBTs are also referred to as symmetrical and asymmetrical IGBTs. These varieties of IGBT differ widely with regard to their fabrication technology, structural details etc. 17. What is full MOSFET?MOSFET stands for metal-oxide-semiconductor field-effect transistor. It is a field-effect transistor with a MOS structure. Typically, the MOSFET is a three-terminal device with gate (G), drain (D) and source (S) terminals. 18. How does an IGBT work as a switch?As defined by being a transistor, an IGBT is a semiconductor with three terminals which work as a switch for moving electrical current. Just as the word “gate” suggests, when voltage is applied to the gate, it opens or “turns on” and creates a path for current to flow between the layers. 19. Can I use transistor instead of MOSFET?It very much depends on the application. BJTs can be cheaper than FETs. This is especially true for high voltage switching where the much larger die area of FETs make them much more expensive. 20. Can IGBT conduct in reverse direction?No. The IGBT cannot conduct current in the reverse direction (from emitter to collector) even with a positive Vge applied to it, because it has a bipolar-type structure. ... However, the gate has no control over this reverse current flow; it is simply the forward biasing of the diode that allows it.
Ivy On 2022-01-28   2217
Transistors

What is IGBT? Structure Explained and Disassembled

Introduction As a power semiconductor device, IGBT(insulated-gate bipolar transistor) is widely used in the fields of rail transit, smart grid, industrial energy saving, electric vehicles and new energy equipment. It has the characteristics of energy saving, convenient installation and easy maintenance, and stable heat dissipation. It is the core device for energy conversion and transmission. A brief overview, IGBT can be said to be a combination of MOSFET(metal–oxide–semiconductor field-effect transistor) and BJT(bipolar junction transistor). That is, it combines the gate voltage control transistor (high input impedance) of the MOSFET, and uses the dual carriers of the BJT to achieve the purpose of large current (voltage-controlled bipolar device). So what is the internal structure of such a combination? This article will explain in detail with examples. What is IGBT and Its Applications Catalog Introduction Ⅰ IGBT Module Explained Ⅱ IGBT Internal Structure Ⅲ IGBT Internal Current Flow Ⅳ How to Disassemble IGBT Module? Ⅴ FAQ Ⅰ IGBT Module Explained The model of the IGBT module to be disassembled as an example is: FF1400R17IP4. The appearance and equivalent circuit of the module are shown in Figure 1. The length, width and height of this module are: 25cmx8.9cmx3.8cm. The module contains two IGBTs, which are what we often call half-bridge modules. The rated voltage and current of each IGBT are 1.7kV and 1.4kA. Figure 1. FF1400R17IP4 Part 8, 9, 10, 11, and 12 are power terminals and need to be connected to a power circuit.1, 2, 3, 4, and 5 are auxiliary control terminals, which need to be connected to the gate drive circuit.6 and 7 are NTC thermistors, used for temperature detection or over-temperature protection.After having a general understanding of its structure, what can we do with such a black module with this structure? Take an example around us: new electric vehicles, everyone should be familiar with it. Three such black modules can be used as a three-phase motor driver. If it is equipped with a battery, it can drive an electric bus. Of course, this module is also used in many other applications. Figure 2. IGBT in Electric Bus   Ⅱ IGBT Internal Structure After having a preliminary understanding of the external structure and application of the IGBT module, let us enter the subject of this article to see what the inside of this high-tech black module looks like. Figure 3 is the internal picture of the IGBT module with the black casing removed. It should be noted that the most common copper and aluminum are inside the IGBT module. Figure 3. IGBT Internal Structure Figure 4 is a cross-sectional view of the IGBT module. If the black casing and external connection terminals are removed, the IGBT module mainly contains 3 components, the heat dissipation substrate, the DBC substrate and the silicon chip (including the IGBT chip and the Diode chip), and the rest is mainly solder layers and interconnecting wires are used to connect IGBT chips, Diode chips, power terminals, control terminals and DBC(Direct Bond Copper). Below we will briefly introduce each part. Figure 4. IGBT Section View ① Heat Sink SubstrateThe bottom of the IGBT module is the heat dissipation substrate, the main purpose is to quickly transfer the heat generated by the IGBT switching process. Since copper has better thermal conductivity, the substrate is usually made of copper, and the thickness of it is 3-8mm. Of course, there are also substrates made of other materials, such as aluminum silicon carbide (AlSiC), both of which have their own advantages and disadvantages. ② DBCDBC (Direct Bond Copper) is a ceramic surface metallization technology, which contains 3 layers. Have a ceramic insulating layer in the middle and a copper clad layer above and below respectively, as shown in Figure 5(a). Simply put, it is to cover both sides of an insulating material with a copper layer, and then etch a pattern that can carry current on the front side, and the back side must be directly soldered to the heat sink substrate. Figure 5. BDC Base vs PCB The main function of DBC needs to ensure the electrical insulation capacity between the silicon chip and the heat dissipation substrate and good thermal conductivity, while also providing a certain current transmission capacity. The DBC substrate is similar to a 2-layer PCB circuit board. The insulating material in the middle of the PCB is generally FR4, while the commonly used ceramic insulating materials for DBC are aluminum oxide (Al2O3) and aluminum nitride (AlN).For the IGBT module analyzed in this article, there are 6 DBCs inside, and each has 4 IGBT chips and 2 Diode chips. Among them, 2 IGBT chips and 1 Diode chip are used as the upper tube, and the rest are used as the lower tube. As shown in Figure 6. Figure 6. DBC Diagram and Equivalent Circuit ③ IGBT ChipThe IGBT chip model used inside the module is: IGCT136T170. The manual can be downloaded from Infineon official website. Figure 7 shows the top view and basic parameters of the IGBT chip. The gate and emitter of the IGBT are above the chip (front side), and the collector is below (back side). The thickness of the chip is 200um. After the IGBT powers on, the current flows from bottom to top, so the IGBT of this structure can also be called a vertical device. Chip Type VCE ICn1) Die Size IGC136T170S8RH2 1700A 117.5A 17.72×7.7mm2 Figure 7. IGBT Chip Diagram If you make a vertical cut on the 200um chip, you can get the internal structure shown in Figure 8, which is a combination of P-type or N-type semiconductors with different doping. Figure 8 shows the well-known equivalent circuit of an IGBT, which is usually understood as a MOS-controlled PNP transistor. When start to learn about power electronics, you may feel that this picture is a bit strange. Why not draw the collector on the top and the emitter on the bottom? Until you understand that the IGBT current flows from bottom to top, it is not difficult to explain. Figure 8. IGBT Chip Structure and Equivalent Circuit Let’s have a general understanding of the electrical parameters of this IGBT chip. This chip can pass a DC current of 117.5A at 100°C. It can be seen from Figure 4 that a single IGBT device inside the module contains a total of 12 IGBT chips, so the total current is: 117.5*12=1412A, which is basically the same as the 1400A rated current in the IGBT module manual.In order to ensure the current sharing effect between IGBT chips, a 11.5Ω resistor has been integrated inside the gate of each chip. At the same time, considering the current sharing between the DBCs, the two chips on each DBC share a gate resistor externally, as shown in Figure 10. When measuring it with a multimeter, and the resistance is about 4.13Ω. You can calculate it in conjunction with Figure 9 to see if it is consistent with the 1.6Ω in the IGBT module manual. Of course, you can refer to the official manual for more detailed parameters of the IGBT chip. Figure 9. IGBT Equivalent Circuit ④ Diode ChipFigure 10 is a top view of the Diode chip, with the anode on the front and the cathode on the back. The current direction of the diode is from top to bottom, which is exactly the opposite of the current direction of the IGBT. The rated current of the diode chip is 235A, and each IGBT is composed of 6 diodes in parallel, and the total current can reach 1410A, which is basically the same as the 1400A in the module manual. The thickness of diode chip is the same as IGBT, it is also 200um. For more detailed parameters of the diode chip, please refer to the official manual. Chip Type VR IFn1) Die Size SIDC130D170H 1700A 235A 16.3×8mm2 Figure 10. Diode Diagram Such a thin semiconductor material can have kV voltage and hundreds of amperes of current on and off, it’s amazing. This is why the price of high-power semiconductor devices is so very expensive.The upper copper layer interconnection of IGBT chip, Diode chip and DBC is generally realized by bonding wires. Commonly used bonding wires are aluminum wire and copper wire. Among them, the aluminum wire bonding process is mature and the cost is low, but the electrical and thermodynamic properties of the aluminum wire bonding are poor, and the expansion coefficient mismatch is large, which affects the service life of the IGBT. The copper wire bonding process has the advantages of excellent electrical and thermodynamic properties, high reliability, and is suitable for modules with high power density and efficient heat dissipation.   Ⅲ IGBT Internal Current Flow After having a basic understanding of the internal structure of the IGBT module, let us go back and interconnect all the above components to see how the current flows inside the IGBT module. Here we take the upper tube IGBT in one of the DBCs as an example to illustrate the current flow. Red represents the current direction of the upper tube IGBT (S1 and S2), and blue represents the current direction of the diode D1. Figure 11(b) is a left cross-sectional view and a schematic diagram of the current direction of the module of Figure . Figure 11(a). IGBT Current Flow Figure 11(b). IGBT Current   Ⅳ How to Disassemble IGBT Module? Some friends may be curious about how to disassemble this module, but it is actually very simple. You only need to prepare two screwdrivers and a small hammer. Figure 12. IGBT Disassemble Step 1: Unscrew the 4 screws at the bottom of the IGBT module.Step 2: Use a flat-blade screwdriver to pry open all the terminals on the front of the IGBT module. This step is very important. It is necessary to ensure that all the terminals after being pried are vertical to the module substrate.Step 3: You need to fix the IGBT in one place, or use a flat-blade screwdriver to align any position of the connection between the plastic casing of the IGBT module and the substrate, hit the screwdriver with a hammer, and pry the casing from the substrate with the screwdriver. After prying open one position, place something on it, and then pry another position, repeat that, after slowly prying open, just pry open with your hands directly.   Ⅴ FAQ 1. What is IGBT module?An IGBT is a is power semiconductor die and is the short form of insulated-gate bipolar transistor. ... An IGBT power module functions as an electronic switching device. By alternate switching direct current (DC) can be transformed to alternating current (AC) and vice versa. 2. How does IGBT module work?The IGBT combines the simple gate-drive characteristics of power MOSFETs with the high-current and low-saturation-voltage capability of bipolar transistors. The IGBT combines an isolated-gate FET for the control input and a bipolar power transistor as a switch in a single device. 3. What is the purpose of IGBT?The IGBT combines, in a single device, a control input with a MOS structure and a bipolar power transistor that acts as an output switch. IGBTs are suitable for high-voltage, high-current applications. They are designed to drive high-power applications with a low-power input. 4. How many layers are there in IGBT?Working of IGBTIGBT is constructed with 4 layers of semiconductor sandwiched together. The layer closer to the collector is the p+ substrate layer above that is the n- layer, another p layer is kept closer to the emitter and inside the p layer, we have the n+ layers. 5. Which are the terminals of IGBT?The three terminals of IGBT are Gate, Collector and Emitter. 6. How many terminals Mosfet has?four terminalsThe MOSFET has four terminals: drain, source, gate, and body or substrate. 7. What is the function of injecting layer in IGBT?The p+ substrate is also called injector layer because it injects holes into n- layer. The n- layer is called drift region. The next p layer is called the body of IGBT. The n- layer in between the p+ & p region serves to accommodate the depletion layer of pn- junction i.e. J2. 8. Can I replace IGBT with MOSFET?Due to the higher usable current density of IGBTs, it can usually handle two to three times more current than a typical MOSFET it replaces. This means that a single IGBT device can replace multiple MOSFETs in parallel operation or any of the super-large single power MOSFETs that are available today. 9. What are the three terminals of an IGBT and how does it function?The IGBT (insulated gate bipolar transistor) is a three-terminal electronic component, and these terminals are termed as emitter (E), collector(C) and gate(G). Two of its terminals namely collector and emitter are associated with a conductance path and the remaining terminal 'G' is associated with its control. 10. What is an IGBT describe its construction?IGBT – Working, Types, Structure, Operation & Applications. ... The IGBT (Insulated Gate Bipolar Transistor) takes the best parts of both BJT and MOSFET into a single transistor. It takes the input characteristics (high input impedance) of MOSFET (Insulated Gate) and the output characteristics of BJT (Bipolar nature). 11. How does IGBT convert DC to AC?The IGBT act as a switch (when a signal is applied to the gate, they turn on and then turn off when the signal is removed). By closing Q1 and Q4, a positive d.c. supply is applied to the load. Q2 and Q3 will result in a negative d.c. supply across the load. 12. What is the advantage of IGBT?The main advantages of IGBT over a Power MOSFET and a BJT are: It has a very low on-state voltage drop due to conductivity modulation and has superior on-state current density. So smaller chip size is possible and the cost can be reduced. 13. What is drift layer in IGBT?The drift region (electric field or movement of charge) of the IGBT works as a base of the PNP transistor . The current gain of the transistor depends upon the width and doping level of the transistor. 14. What is the structure of IGBT?The structure of IGBT is very much similar to that of PMOSFET, except one layer known as injection layer which is p+ unlike n+ substrate in PMOSFET. This injection layer is the key to the superior characteristics of IGBT. Other layers are called the drift and the body region. The two junctions are labeled J1 and J2. 15. What are the advantages of IGBTs?Advantages of IGBT:Simple drive circuitLow on-resistanceHigh voltage capacityFast switching speedEasy of driveLow switching lossLow on stage power dissipationLow gate drive requirement 16. Why IGBT is very popular nowadays?With its lower on-state resistance and conduction losses as well as its ability to switch high voltages at high frequencies without damage makes the Insulated Gate Bipolar Transistor ideal for driving inductive loads such as coil windings, electromagnets and DC motors. 17. Why diode is used in IGBT?We know that MOSFET or IGBT is a unidirectional device, they only conduct current in forward bias and block the current in reverse bias. ... For this reason, an external diode is connected across the MOSFET or IGBT or SCR to provide a path for reverse current.
kynix On 2022-01-05   5998
Relays

Latching Relay Definition, Basic Functions and Selection

Introduction Latching relay is a new type of relay and also an automatic switch. Like other electromagnetic relays, it turns on and off the circuit automatically. The difference is that the normally closed or normally open state of it is completely dependent on the action of permanent magnets, and the switching state of it is triggered by a pulse electric signal of a certain width. It has the characteristics of power saving, stable performance, small size, large carrying capacity, and superior performance than general relays. Latching Relay Basics in 2 Minutes Catalog Introduction Ⅰ Working Principle 1.1 Action Principle 1.2 Action Process Ⅱ Main Functions and Advantages 2.1 Average View 2.2 Function Lists 2.3 Application Area Lists 2.4 Latching Relay Advantages Ⅲ Tech Parameters Ⅳ Latching Relay Test 4.1 Measuring Contact Resistance 4.2 Measuring Coil Resistance 4.3 Set Voltage and Current 4.4 Reset Voltage and Current Ⅴ Relay Selection 5.1 The Necessary Conditions 5.2 Relevant Information Search 5.3 Installation Layout Consideration Ⅵ FAQ Ⅰ Working Principle 1.1 Action Principle The on and off state of the latching relay is usually held by the magnetic force generated by the permanent magnet. When the contacts of the relay need to be opened or closed, only the positive (reverse) DC pulse voltage is needed to excite the coil, and the relay completes the state transition between opening and closing in an instant. Usually when the contact is in the holding state, the coil does not need to continue to be energized, and the state of the relay can be maintained unchanged only by the permanent magnet force.   1.2 Action Process When the contacts of the relay need to be set, it is only necessary to excite the coil J2 with a positive DC pulse voltage. The magnetic poles generated by the coil J2 after excitation interact with the magnetic poles of the permanent magnet. As we all known, the same polarities repel each other, but the opposite polarities attract each other. The state transition from reset to set is completed in an instant. The following schematic diagrams demonstrates the specific state transition process. The process of the latching relay changing from the set state to the reset state, which are the same. Figure 1. Reset Latching Relay Figure 2. Constant-Current Pulse Monment Figure 3. Constant-Current Pulse Monment Figure 4. Latching Relay Reset   Ⅱ Main Functions and Advantages 2.1 Average View Latching relay is an automatic switching element with isolation function. It is widely used in remote control, telemetry, communication, automatic control, mechatronics and power electronic equipment. It is one of the most important control elements in electricity.Magnetic latching relays generally have an induction mechanism (input part) that can reflect certain input variables (such as current, voltage, power, impedance, frequency, temperature, pressure, speed, light, etc.). It has the ability to turn on/off the controlled circuit. In addition, between the input part and output part of the relay, there is an intermediate mechanism (drive part) for coupling and isolating the input, functional processing and driving the output part. 2.2 Function Lists The latching relay has the following functions:1) ExpansionFor example, when the control signal of a multi-contact relay reaches a certain value, multiple circuits can be switched, disconnected, and connected at the same time according to different forms of contact groups.2) AmplificationFor example, magnetic latching relays can control a large-power circuit with a very small control quantity.3) IntegrationFor example, when a plurality of control signals are input to a multi-winding relay in a prescribed form, they will be compared and integrated to achieve a predetermined control effect.4) Automation, remote control and monitoringFor example, on the automatic device and other electrical appliances, magnetic latching relays can form a program control circuit to realize automatic operation. 2.3 Application Area Lists 1) Smart meters: IC card meters, prepaid meters, single-phase meters, three-phase meters.2) Reactive power compensation: synchronous switch, composite switch, smart capacitor.3) Intelligent control: smart home, solar street light control, automation equipment, etc. 2.4 Latching Relay Advantages 1) They only need pulse excitation, and can work with single and double coils.2) Small size, easy installation.3) Low power consumption and strong load capacity.4) Safe and reliable, long service life. Figure 5. General Relay Structure Ⅲ Tech Parameters 1) Rated VoltageIt refers to the voltage required by the coil when the relay is working normally. Depending on the model of the relay, it can be AC voltage or DC voltage.2) DC ResistanceIt refers to the DC resistance of the relay coil, which can be measured by a multimeter.3) Pull-in CurrentIt refers to the minimum current that the relay can produce the pull-in action. In normal use, the given current must be slightly larger than the pull-in current, so that the relay can work stably. As for the working voltage applied to the coil, generally do not exceed 1.5 times the rated working voltage, otherwise it will generate a larger current and burn the coil.4) Release CurrentIt refers to the maximum current that the relay generates to release the action. When the current in the pull-in state of the relay is reduced to a certain level, it will return to the unpowered release state. The current at this time is much smaller than the pull-in current.5) Switch Voltage and CurrentThis refers to the voltage and current that the relay allows to load. It determines the magnitude of the voltage and current that the relay can control, and you cannot be exceeded this value during use, otherwise it is easy to damage the contacts of the relay.6) Coil Resistance RThe resistance produced by winding a T circle with an enameled wire with a diameter of Φ: R=£*(T/Φ).7) TemperatureThe higher the temperature, the greater the resistance, and the lower the resistance, the smaller the resistance. Generally speaking, the coil resistance refers to the coil resistance at 20°C. When the temperature is higher or lower than 20℃, there is a calculation formula: Rt=R20[1+(T℃-20℃)×0.004].8) Contact Resistance CRIt is the resistance between the contacts of the relay. And it is the sum of the shrinkage resistance Re and the surface film resistance Rf: Rk=Re+Rf.Note:🔺The factors that form shrinkage resistance Re:♦️The size of the contact pressure determines the size of the shrink resistance. The relationship between the two is inversely proportional, the greater the contact pressure, the smaller the shrinkage resistance.🔺The factors that form the surface film resistance Rf:♦️Dust in the air.♦️Harmful gases in the air: H2S, SO2, etc.♦️Organic vapor in the air: plastic, glue and rosin.♦️Oil stains on the contact surface during the production process.9) Pull-in VoltageThe minimum voltage required to close the relay contacts.10) Release voltageThe minimum voltage required to open the relay contacts.11) Insulation ResistanceThe resistance value that appears when measured with a specified DC voltage between conductive parts that are insulated from each other.12) Medium Withstand VoltageAlso known as dielectric degree, it refers to the maximum voltage that can withstand between two conductive parts without breakdown.13) Reversing RetentionThe minimum force applied on the armature assembly handle to open or close the contacts.14) Contact PressureThe interaction force generated between the moving and static contacts is equal to the contact pressure equal to the reaction force generated by the over-travel of the reed head. Figure 6. Latching Relay Product Ⅳ Latching Relay Test 4.1 Measuring Contact Resistance Use the resistance profile of the universal meter to measure the resistance of the normally closed contact and the moving point, which should be 0. The contact resistance can be measured in a more accurate way within 100 milliohms, while the resistances of the normally-open contact and the moving point should infinite. From this, it can be distinguished which is a normally-closed contact or a normally-open contact.   4.2 Measuring Coil Resistance The resistance value of the relay coil can be measured with the universal meter R×10Ω, so as to judge whether there is an open circuit phenomenon in the coil.   4.3 Set Voltage and Current Get an adjustable regulated power supply and an ammeter, input the set voltage to the relay, and insert an ammeter in the power supply loop for monitoring. Slowly increase the power supply voltage, and when you hear the sound of the relay picking up, write down the set voltage and set current. In order to be accurate, you can try several times. Pay attention to, the setting current should be the average value, and the setting voltage should be the maximum value.   4.4 Reset Voltage and Current Repeat the above operation. But there is a little difference that the reset current is the average value, and the reset voltage is the maximum value.   Ⅴ Relay Selection 5.1 The Necessary Conditions ① The power supply voltage of the control circuit, the maximum current that can be provided.② The voltage and current in the controlled circuit.③ How many sets and types of contacts are needed for the controlled circuit. When selecting a relay, the power supply voltage of the general control circuit can be used as the basis for selection. The control circuit should be able to provide enough working current to the relay, otherwise the relay will be unstable when it is closed.   5.2 Relevant Information Search After consulting the relevant information to determine the conditions of use, you can search for the relevant information to find out the model and specification number of the required relay. If you already have a relay on hand, you can check whether it can be used based on the data. Finally, consider whether the size is appropriate.   5.3 Installation Layout Consideration If it is used for general electrical appliances, in addition to considering the volume of the case, it is necessary to consider the installation layout of the circuit board. For small electrical appliances, such as toys and remote control devices, ultra-small relay products should be used.   Ⅵ FAQ 1. What is magnetic latching?The design of a Magnetic Latching Relay is such that when a short pulse of electrical energy is applied to the solenoid coil, sufficient magnetic force is generated to over-come the force of the relay' return mechanism. 2. How does a latching relay work?One latching type has two opposing coils with an over-center spring or permanent magnet hold the contacts in position after the coil is de-energized. A pulse to one coil turns the relay on and a pulse to the opposite coil turns the relay off. 3. Where is latching relay used?This type of relay is most suitable in applications like ON/OFF devices from multiple places with push-button or momentary switch. For example, it is used in a lighting circuit or conveyer to control from different locations. 4. What is a magnetic latching relay used for?A magnetic latching relay is a device in which the solenoid principle is applied to open and close light-current electrical circuits. The same device applied in heavy-current circuits is called a contactor, or circuit breaker. 5. How does a latching relay reset?Resetting is very simple. The coil circuit needs to be opened and shortened to the coils ground potential. The capacitor will be discharged through the coil and drives a current pulse with opposite polarity through the coil.
kynix On 2021-12-18   1866

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.