Phone

    00852-6915 1330

ics Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

Resistors

LED Drivers Tutorial: Failure Analysis and Maintenance

IntroductionLED lights cannot directly use the conventional mains grid voltage, because of the characteristics of LED lighting. In order to meet the special voltage and current requirements of LEDs, a specially designed voltage conversion device must be used to make LEDs work normally. This device is an LED driver. LED drivers are usually switching mode devices that convert the input voltage (Typically 120-220 VAC or 12 VDC) into a voltage at which the current drawn by the LED's is equal to its drive current. The drive current is regulated for optimum brightness, led service life, and battery life. A drive current lower than the maximum drive current of an LED can greatly prolong service life. As a key part of LED lighting, the quality of LED drivers directly affects the performance of LED lighting.Choose the Correct LED Drivers For LED LightsNo matter how good the quality of the LED driver is, failure and maintenance are inevitable. This article will analyze the 10 failures in LED lighting design and its application based on the relevant technology and practical experience of the LED driver.CatalogIntroductionⅠ LED Driver Failure Analysis1.1 Forward Voltage Drop (Vf) Range1.2 Power Margin and Derating Requirements1.3 LED Working Characteristics1.4 Test Session1.5 Different Load with Different Test Results1.6 LED Driver Circuit Problem1.7 Wrong Phase Wring1.8 Grid Fluctuation1.9 Frequent Line Trips1.10 Drive CoolingⅡ LED Driver Maintenance2.1 Multimeter to Detect LED Driver2.2 Identify LED Power SupplyⅢ LED Driver Circuit Modulation3.1 Pulse Width Modulation (PWM)3.2 Pulse Frequency Modulation (PFM)3.3 Sliding-Mode ModulationⅣ One Question Related to LED DriverⅠ LED Driver Failure AnalysisThe LED driver is measuring current passing through LEDs using sense resistor and then increase or decrease the voltage to maintain constant current continuously. LEDs are kind of diode so they need DC voltage to operate so most of the LED drivers are boost and can vary output supply in wide range (example, 16V to 38V). They also have dimming control by PWM signal from microcontroller OR by having a manual potentiometer to change sense resistor. According to them, LED driver failures are complex, but we can follow the steps below to analyse.1.1 Forward Voltage Drop (Vf) RangeLED lamp load end is generally composed of a number of LEDs connected in series, and its working voltage Vo=Vf×Ns, where Ns represents the number of LEDs. And the Vf of an LED varies with temperature. Generally, at a constant current, Vf becomes lower at high temperatures and becomes higher at low temperatures. The LED lamp load working voltage is VoL at high temperature, and VoH represents a value at low temperature. When selecting an LED driver, consider that the driver output voltage range is greater than VoL~VoH.If the maximum output voltage of the LED driver is lower than VoH, the maximum power of the lamp may not reach the actual power required at low temperature. If the minimum voltage of the selected LED driver is higher than VoL, the output of the driver may exceed the working range at high temperature. And LED driver will work unstable, making the lights flicker.Considering the overall cost and lamp efficiency, don’t blindly pursue the ultra-wide output voltage range of the LED driver. Because the driver voltage is only in a certain range, its efficiency is the highest. When the range is exceeded, the efficiency and power factor (PF) will deteriorate. In addition, if the design of the driver output voltage range is too wide, high costs and unoptimized efficiency will be made. 1.2 Power Margin and Derating RequirementsIn general, the nominal power of the LED driver refers to the data measured under the rated environment and rated voltage. Taking into account different applications, most LED driver suppliers will provide power derating curves in their product specifications (common load vs. ambient temperature derating curves and load vs. input voltage derating curves).As shown in Figure 1, the red curve represents the power derating curve when the input is 120Vac, and its load varies with the ambient temperature. When the ambient temperature is lower than 50℃, the LED driver is allowed to be 100% full load. When the ambient temperature is as high as 70℃, the LED driver can only be derated to 60% of the load. When the ambient temperature changes between 50℃~70℃, the driver load varies with the temperature linearly.Figure 1. Power Derating Curve (Load vs Ambient Temperature)The blue curve represents the power derating curve when the input is 230Vac or 277Vac, and its load varies with the ambient temperature. The principle is similar to the above mentioning.As shown in Figure 2, the blue curve represents the derating curve of the LED driver when the ambient temperature is 55°C, its output power varies with the input voltage. When the input voltage is 140Vac, the load of the driver is allowed to be 100%, and the input voltage will be adjusted downward. If the output power remains the same, the input current will rise, resulting in input terminal loss and lower efficiency. When the device temperature rises, exceeding the rated temperature, which may cause the device to fail.Figure 2. Power Derating Curve (Load vs Input Voltage)Therefore, when the input voltage is less than 140Vac, the output load of the LED driver is required to linearly decrease as the input voltage decreases. According to the above derating curve and corresponding requirements, when choosing a LED driver, actual applying needs are important, as well as the derating margin. 1.3 LED Working CharacteristicsWhen the required input power is a fixed value, such as a fixed error of 5%, the output current can only be adjusted to the specified power for each lamp. Due to different working ambient temperature and different lighting time, the power of each lamp will vary greatly.Although there are considerations for marketing and business factors. However, the volt-ampere characteristic of the LED lamp determines that the LED driver is a constant current source, and its output voltage varies with the series voltage Vo of the LED load. When the efficiency of the driver is basically unchanged, its input power changes with Vo. And meanwhile, the overall efficiency of the LED driver will increase after thermal equilibrium. Under the same output power, the input power will decrease compared to the boot time.Therefore, when formulating requirements, LED driver users should first understand the operating characteristics of LEDs. Avoid suggesting indicators that do not meet the principles of operating characteristics, and indicators that far exceed actual requirements, resulting in excess quality and cost waste. 1.4 Test SessionSample test problems, for example, multi-brand LED driver samples all failed during the test. The reason is that a self-dual voltage regulator is used to directly power the LED driver for testing. After power on, the voltage regulator is gradually adjusted from 0Vac to the rated operating voltage of the LED driver. This kind of test operation can easily make the LED driver start and work with the load when the input voltage is very small, but this situation will cause the input current to be far greater than the rated value. And the internal input terminal related components, such as fuses, rectifier bridges, thermistors, etc. will fail due to excessive current or overheating, damaging the LED driver.The correct test method is to adjust the voltage regulator to the rated operating voltage range of the LED driver, and then connect the driver to power-on test. Of course, technically improving the design can also avoid the failure caused by this kind of test misoperation. That is, a starting voltage limit circuit and an input undervoltage protection circuit are set at the input of the driver. When the input does not reach the start-up voltage set by the driver, the driver does not work. When the input voltage drops to the input undervoltage protection point, the driver enters the protection state. Although the driver has a self-protection function and will not fail, you must carefully understand whether the purchased LED driver product has this protection before testing (considering the actual application environment of the LED driver, most LED drivers currently do not have this set). 1.5 Different Load with Different Test ResultsOn the one hand, when the LED driver is tested with LED lights, the result is normal; on the other hand, when driver tested with an electronic load, the result may be abnormal. Usually this phenomenon has the following reasons:1) The output instantaneous voltage or power of the driver exceeds the working range of the electronic load instrument. (Especially in CV mode, the maximum test power should not exceed 70% of the maximum power of the load. Otherwise, the load may instantaneously have overpower protection when loading, causing the driver to fail to work.)2) The characteristics of the electronic load instrument used are not suitable for measuring constant-current device. And the load voltage gear jumping, result in the drive to fail to work.3) Because there is a large capacitor inside the input of the electronic load meter. The test is equivalent to connecting a large capacitor in parallel with the driver output, which may cause the driver's current sampling work to be unstable. As we all known, the LED driver is designed to meet the working characteristics of LED lamps. The most practical test method is to use the LED lamp as a load, and connects an ammeter and a voltmeter in series to test. 1.6 LED Driver Circuit ProblemThe following conditions often cause damage to the LED driver:Connect AC to the DC output terminal of the driver, causing the driver to fail.Connect AC to the DC/DC output or input of the driver, causing the driver to fail.Connect the output terminal of the constant current to the dimming light, causing the driver to fail.Connect the phase wire to the ground wire causing the driver has no output and the housing is charged. 1.7 Wrong Phase WringTake an international example: the rated working voltage between each phase line and the neutral line is 220V, and the voltage between the phase line and the phase line is 380V. If the driver is connected to two phase wires, after power on, the LED driver input voltage exceeds the rated range, which cause the product to fail.As shown in Figure 3, V1 represents the first phase voltage, V2 represents the second phase voltage, and R1 and R2 respectively represent the drivers normally installed on the line. When the neutral line (N) on the circuit is disconnected, the drivers R1 and R2 on the two branches are connected to the 380V voltage after being connected in series. Because of the difference in input internal resistance, when one of the drivers is charged to start, the internal resistance becomes smaller. Most of the voltage may be applied to another driver, causing the overvoltage damage. Therefore, it is recommended that switches or short-circuiters on the same distribution branch should be disconnected together, not just cut off the neutral line. What’s more, do not put the power distribution fuse on the neutral line to avoid bad effect of the neutral line on the circuit.Figure 3. Neutral Line Open Circuit Diagram 1.8 Grid FluctuationWhen wires of a transformer grid branch is too long and there is large power equipment on the branch, the grid voltage will fluctuate sharply when the large equipment starts and stops. It even causes the grid to be unstable. When the grid voltage exceeds 310V, the drive may be damaged (even if there is an LED lightning protection device, it is useless. Because the lightning protection device is to deal with pulse spikes of tens of uS level, and the fluctuation of the grid may reach tens of mS, or even hundreds of mS) . Therefore, special attention should be paid when there is large electric machinery on the street lighting branch power grid. It is best to monitor the fluctuation range of the power grid or to supply power to the grid transformer separately. 1.9 Frequent Line TripsToo many lights are connected on the same branch, which leads to overload on a certain phase and uneven power distribution among the phases, resulting in frequent line trips. 1.10 Drive CoolingAlthough the LED has high luminous efficiency, only a small part of the energy flowing through the LED is radiated in the form of visible light. And most of the remaining energy is consumed in the LED in the form of heat, so the LED generates more serious heat. When the driver is installed in a non-ventilated environment, the driver housing should be in contact with the lamp housing as much as possible. If possible, apply thermal glue or a thermal pad on the contact surface between the housing and the lamp housing to improve the heat dissipation of the LED driver and ensure the reliability of the driver.Ⅱ LED Driver Maintenance2.1 Multimeter to Detect LED DriverMeasuring the output voltage of the no-load LED driver with a multimeter, if the output voltage is not detected, does it mean that the driver is broken? Look at the following steps:1) The voltage of the non-isolated LED power supply in the no-load state is about 300V tested with a multimeter, and it is about 220V with a PFC.2) Isolating the LED power supply, the voltage in the no-load state, tested with a multimeter, is about 3-5V more than the total voltage of the rated LED series. However, although the output voltage can be tested under no load, it does not mean that it can be normal under load. At this time, it is necessary to connect the corresponding LED light board to see the performance of the LED lighting. If there is no flicker, the output voltage is also equal to the total voltage of LED lights in series connection. This situation can be considered normal, otherwise it fails. If there is no output voltage at no load, the power supply must be broken. 2.2 Identify LED Power SupplyThe LED power supply is widely used in many applications. So how to distinguish the quality of LED power supply is particularly important. A few methods are briefly introduced below. LED Driver ICThe power of IC drive, the quality of IC directly affects the whole power supply. The lighting manufacturer should understand the IC design solution and calculate the cost of the driver, so as to purchase power products at a reasonable price. TransformersThe control chip can be regarded as the brain center of the power supply, while the transformers determine the power and temperature resistance. The transformer is responsible for the transfer of "AC to DC". However, the energy overload will damage the device. The core of the transformer is the magnetic core and the wire package. Electrolytic Capacitors and Ceramic CapacitorsThe quality and life requirements of input electrolytic capacitors are important. However, people tend to ignore the quality requirements of the output capacitor. In fact, the life of the output capacitor also has a great impact on the life of the power supply. The output end has a switching frequency of up to 60,000 times per second, which causes the parasitic resistance of the capacitor to heat up and produce substances similar to scale. Finally, the electrolyte heats up and bursts. Ceramic capacitors: The materials are divided into X7R, X5R and Y5V, and the actual capacitance value of Y5V can only reach 1/10 of the actual value. In addition, the nominal capacitance value only refers to when a capacitor works at 0V. Therefore, this tiny chip with poor options will also lead to a price difference in cost and greatly shorten the life of the power supply. Circuit Design and Welding ProcessJudgment of the pros and cons of the design: Aside from the professional point of view, it can be distinguished by some intuitive methods, such as the neat layout of the components, and soldering points. As for flying leads and manually adding components, it is a serious lack of techniques and efficiency. As we all know, the quality of mechanized production of wave soldering process is definitely better than manual welding. Because the machining process is more neat and uniform. Identification method: whether there is red glue on the back board.The flashing phenomenon of the lamp after a period of use is basically caused by the power supply or the weak welding of the lamp beads. However, it is extremely difficult to detect the virtual welding of products through aging, so AOI must be used to detect the quality of the power supply. Batch Inspection of Aging Racks and High Temperature Aging RoomsNo matter how good the power products are controlled by materials and production processes, they still need to be tested for aging. Because the incoming inspection of electronic components and transformers is difficult to control. Only through the aging of the entire batch of power supplies and the high temperature sampling inspection of the high temperature room. This is a wide-ranging screening to determine whether the materials have safety hazards. Ⅲ LED Driver Circuit ModulationThe LED driver circuit is divided into constant-voltage type and constant-current type according to the power supply to the LED. Constant-current switch type LED driver circuit samples the current flowing through the LED lamp, and gives the output control signal to control the on and off of the switching power tube, which aims to adjust the output current as the set value. The dimming control circuit mainly includes SCR dimming circuit, pulse width modulation (PWM), pulse frequency modulation (PFM), sliding mode control, PWM_PFM, PSM, etc. Let's take pulse width modulation (PWM), pulse frequency modulation (PFM), and sliding mode modulation to introduce in detail below. 3.1 Pulse Width Modulation (PWM)Pulse width modulation, shown in the figure below, refers to the stability of the output voltage by changing the on-time of the switching power tube in each cycle at a specific frequency. That is adjusting the duty cycle to obtain stable output voltage. When the output voltage changes due to the working environment, noise and other factors, the error amplifier samples the voltage change and sends the signal to the control circuit. The control circuit adjusts the duty cycle of the switching power tube signal to maintain the stability of the output voltage.Figure 4. PWM Modulation Based on BUCK StructureFigure 4 (a). Voltage ModeFigure 4 (b). Peak Current ModeFigure 4 (c). Average Current Mode3.1.1 Advantages of PWM(1) The PWM modulation method has high efficiency under heavy load, and has a good dynamic response to load changes.(2) The output ripple voltage is small and the linearity is high.(3) The frequency is stable, the duty cycle adjustment is not restricted, the control is simple, and both the current control mode and the voltage control mode are applicable.3.1.2 Disadvantages of PWM(1) The efficiency of PWM modulation method decreases at light load.(2) The transient response is slow during constant-voltage driving, and a more complicated compensation circuit is required.(3) Accurate current detection circuit is required for constant-current driving. 3.2 Pulse Frequency Modulation (PFM)The pulse frequency modulation is shown in the figure below. Under the condition of a certain on-time of the switching power tube, the output voltage can be controlled by adjusting the off time. When the output voltage changes, the error amplifier samples the feedback signal and sends the output signal compared with the reference signal to the control circuit. The control circuit analyzes the error signal and generates a square wave signal with constant pulse width and varying frequency to control the switch power tube to maintain the stability of the output voltage.Figure 5. Pulse Frequency Modulation Based on BUCK Structure3.2.1 Advantages of PFM(1) The PFM modulation has very high efficiency, better frequency characteristics and higher voltage regulation rate at light load.(2) The PFM modulation has a relatively high transmission signal-to-noise ratio and a good anti-interference ability.(3) The output voltage has a large adjustable range and low power consumption.3.2.2 Disadvantages of PFM(1) The efficiency of the PFM modulation will decrease under heavy load.(2) The frequency spectrum of the output ripple is scattered and irregular.(3) The load adjustment range is very small, resulting in high filtering costs. 3.3 Sliding-Mode ModulationSliding-mode modulation mode, the full name is sliding mode variable structure control,  is a discontinuous control. As shown in Figure 6, the sliding mode makes the system structure change purposefully according to its current state, which force the system to make small amplitude and high frequency up and down movements along the designed trajectory under response conditions. That is, sliding mode movement. Reduce the system's sensitivity to disturbances and load jumps.Figure 6. Sliding Mode Control Based on BUCK Structure3.3.1 Advantages and Disadvantage of Sliding ModeIt has the advantages of fast dynamic response, strong robustness and wide stability range, but it also has a problem that the operating frequency is not fixed. Ⅳ One Question Related to LED Driver4.1 QuestionHow long do LED drivers last?4.2 AnswerWhile the light function of an LED may last for years, drivers can give out much sooner. This is why we recommend name brand LED bulbs for the home, especially those with 25,000 hour rated lives. In general, high power white LEDs use much more current, and need of more complicated drivers. Frequently Asked Questions about LED Drivers Failure Analysis and Maintenance1. What is a LED driver IC?They are configured as either inductorless (charge pump) or switching regulator-based LED drivers that support driving white LEDs in series, parallel or combination. ... Topologies include boost regulator, buck regulator, buck/boost, SEPIC topology LED drivers, and more. 2. What is a LED driver used for?LED drivers are electrical devices that prevent damage to LEDs by regulating the forward voltage (VF) of the LED that changes with temperature, avoiding thermal runaway while delivering a constant current to the LED. LED drivers also aid efforts to meet new energy requirements (e.g., Energy Star). 3. How do I choose an LED driver?Use an LED driver with at least the same value as your LED(s). The driver must have a higher output power than your LEDs require for extra safety. If the output is equivalent to the LED power requirements, it is running at full power. Running at full power may cause the driver to have a shorter life span. 4. Why do LED drivers fail?LED FailureThe LEDs usually fail, because they have been connected to a constant LED driver in parallel. If the LEDs have failed you may want to also replace the LED driver. We usually recommend using a model with an adjustable output, and trimming down the output voltage slightly, to avoid over powering the LEDs. 5. How long do LED drivers last?Namely, the life of the driving circuit expires prior to when the LED stops emitting light or has its brightness dropped. The typical nominal lifetime of these elements is often times less than 25,000 hours, while the lifetime of LED itself could be as long as 50,000-100,000 hours. 6. Why do my LED drivers get hot?If the LED driver is trying to draw DC (not a balanced load circuit) then that can also cause the transformer to overheat.7. What is the difference between a transformer and an LED driver?LED drivers and electronic transformers for retrofit LED lighting are not interchangeable. They differ in output and load compatibility i.e. which LED lights they will work with. The fundamental difference between the two is that LED drivers output DC while electronic halogen transformers output 12VAC.
kynix On 2020-09-11   13306
Resistors

Oscillator Basics: Oscillator Circuit Types Explanation

IntroductionSimply put, an oscillator is a device that can convert DC power into AC power without external signal excitation. The so-called "oscillation" implies alternating current. This article will mainly explain the circuits of different sine wave oscillators, including their working principles, how to realize their functions, circuit composition and comparison of advantages and disadvantages of different forms of circuits. This article uses a large number of circuit diagrams and formulas to explain in detail, which can help you understand in a better way.Basics of oscillators and their different typesCatalogIntroductionCatalogI The Principle of Feedback Oscillator1.1 How Does the Feedback Oscillator Work?1.2 Equilibrium Conditions1.3 Starting Conditions of the Oscillator1.4 Stable Conditions of the Oscillator1.5 General Composition of Sine Wave OscillatorII LC Oscillator Circuit2.1 The Composition Principle of the Oscillator2.2 Capacitive Feedback Oscillator2.3 Inductive feedback oscillatorIII RC Oscillator Circuit3.1 Brief Introduction of RC Oscillator and its Circuit3.2 RC Phase Shift Oscillator3.3 Wien Bridge OscillatorIV Quartz Crystal Oscillator Circuit4.1 What is a Quartz Crystal Oscillator?4.2 Quartz Crystal4.3 Quartz Crystal Oscillator CircuitV Non-sine Wave Generating Circuit5.1 What is a Non-sine Wave Generating Circuit?5.2 Rectangular Wave Generator5.3 Triangle Wave and Sawtooth Wave Signal GeneratorVI QuizⅦ FAQI The Principle of Feedback Oscillator1.1 How Does the Feedback Oscillator Work?The feedback oscillator is when the power is turned on, the various electrical disturbance signals in the loop are selected by the frequency selection network, and the signal of a certain frequency is fed back to the input terminal, and then the cycle of amplification → feedback → amplification → feedback , The amplitude of the signal increases continuously, and the oscillation is established from small to large. As the signal amplitude increases, the amplifier will enter a non-linear state, and the gain will decrease. When the feedback voltage is exactly equal to the input voltage, the oscillation amplitude will no longer increase and enter a balanced state. As can be seen from the figure below, the feedback oscillator is a closed loop composed of an amplifier and a feedback network. The amplifier is usually a tuned amplifier with an oscillation circuit as a load. The feedback network is generally a linear network composed of passive components.Figure1. Block Diagram of Feedback OscillatorIn order to generate self-oscillation, there must be positive feedback, that is, the signal fed back to the input terminal and the signal at the input terminal of the amplifier have the same phase. For the above figure, suppose the voltage amplification factor of the amplifier is K(s), the voltage feedback coefficient of the feedback network is F(s), and the closed-loop voltage amplification factor is Ku(s), thenby We can writeIf a certain frequency ω1=ω, then T(jω1) is equal to 1. From the above formula, we can see that Ku(jω) will tend to infinity. This shows that there is no external signal, and self-excited to produce signal output, namely self-oscillation. Therefore, the condition of self-oscillation is that the loop gain is 1.Definition:1.2 Equilibrium ConditionsThe equilibrium condition of the oscillator isthis can also be expressed asIf a certain frequency ω1=ω, then T(jω1) is equal to 1. From the above formula, we can see that Ku(jω) will tend to infinity. This shows that there is no external signal, and self-excited to produce signal output, namely self-oscillation. Therefore, the condition of self-oscillation is that the loop gain is 1. The above two formulas are the amplitude and the phase equilibrium conditions respectively. Equilibrium conditions are also called "two conditions for maintaining self-oscillation". The amplitude balance condition determines the amplitude of the oscillator output signal, and the phase equilibrium condition determines the frequency of the oscillator output signal. But it must be pointed out that the loop can only meet the phase equilibrium condition at a certain frequency (f), which is the resonant frequency (f0) of the loop.1.3 Starting Conditions of the OscillatorWhen the oscillator is in actual application, there should be no external signal Us(s) shown in Figure 1. The initial source of oscillation is electrical signals such as electrical shock and various thermal noises that inevitably exist when the oscillator is switched on.It can be seen from the establishment process of the oscillation that in order to make the oscillator start-up, the feedback voltage Uf and the input voltage Ui should be in phase at the beginning of the oscillation (that is, positive feedback); Uf>Ui should be required in amplitude, that is:Vibration conditions: φA+φF=2nπ(n=0,1,2,•••)AF>1 Simply put, as we know, the condition of unity gain must be met to make the oscillation continue. But to start the oscillation, the voltage gain of the positive feedback loop must be greater than 1, so that the amplitude of the output voltage can reach the required potential. Then the gain must be reduced to 1, so that the output voltage can be maintained at the required potential and the oscillation phenomenon can continue. Transition from |T(jω)|>1 to |T(jω)|=1 when the oscillator is workingThe amplifier must work in the linear amplification region of the transistor when amplifying small signals.When the oscillation is started, the amplifier works in the linear region. At this time, the output of the amplifier increases linearly with the increase of the input signal; as the amplitude of the input signal increases, the amplifier gradually enters the saturation or cut-off region from the amplification region, and enters a nonlinear state. The closed-loop gain of will decrease with the increase of the input signal, as shown in the figure below:Figure2. Graphical Representation of Amplitude ConditionsWhen the loop gain drops to |T(jω)|=1, the growth process of the amplitude will stop, and the oscillator will reach a balanced state and perform constant amplitude oscillation. It can be seen that the transition of the oscillator from amplified oscillation to steady amplitude oscillation is realized by the non-linear characteristics of the amplifier. When the oscillating circuit is powered on, the current of the transistor increases abruptly from zero, and the sudden change current contains a wide spectrum component. The start-up process of the circuit is very short! As long as the circuit satisfies the starting conditions, after the oscillator is powered on, there will be an output signal with stable amplitude at the output.Figure3. Circuit Start-up Process1.4 Stable Conditions of the OscillatorIf the loop gain characteristic has two equilibrium points A and B, among them, point A is stable and point B is unstable.Figure4. Stable Conditions of the OscillatorIt can be seen from the above discussion that in order to stabilize the equilibrium point, |T(ω0)| must have a negative slope change near UiA.Stable conditions are divided into amplitude stable conditions and phase stable conditionsTo make the amplitude stable, the oscillator must have the ability to prevent amplitude changes at its equilibrium point. Then the amplitude stability condition should beSince the feedback network is a linear network, which means the size of the feedback coefficient does not change with the input signal, so the amplitude stability condition can be written asThe phase stability depends on the increase of ω, and the decrease of , meaning that the phase characteristic of the parallel oscillator circuit ensures the phase stability.Therefore, the phase stability condition is. The higher the Q value of the loop,  the larger of the value of , and the better phase stability.1.5 General Composition of Sine Wave Oscillator(1) Amplifying circuit-realize energy control.(2) Positive feedback network-meets the conditions for starting vibration.(3) Frequency selection network-only one frequency satisfies the oscillation condition to obtain a sine wave output of a single frequency. Commonly used frequency selection networks include RC frequency selection and LC frequency selection(4) Amplitude stabilization link-makes the circuit easy to start and oscillate stably, with little waveform distortion. Examples of oscillation circuits:High frequency resonant amplifier and sine wave oscillatorFigure5. High Frequency Small Signal Resonant AmplifierFigure6. Mutual Inductance Coupled OscillatorII LC Oscillator CircuitLC oscillators can be divided into three types: mutual inductance coupled oscillators, inductive feedback oscillators and capacitive feedback oscillators according to their different feedback networks.This section focuses on different types of feedback LC oscillators and three-point oscillators.2.1 The Composition Principle of the OscillatorFigure7. General Form of Three-terminal OscillatorThe basic circuit is the so-called three-terminal (also called three-point) oscillator, which means the circuit formed by connecting the three terminals of the LC loop and the three electrodes of the transistor respectively, as shown in the figure. The three-terminal LC oscillator is a feedback type LC oscillator. In order to obtain positive feedback, the feedback circuit must make the instantaneous polarity of the transistor's AC voltage meet a certain phase relationship: when Vbe is negative, Vce should be positive, namely, Vbe and Vce are in reverse phase, and Veb and Vce are in phase. Only when the reactance Xce and Xeb have the same properties can they be guaranteed to be in phase. When the resistance of the loop element is very small, its influence can be ignored, and the influence of the input impedance and output impedance of the transistor can also be ignored. To maintain oscillation, the circuit must meet the requirements. Otherwise, the loop resonance condition cannot be met.The criteria for the three-terminal oscillator circuit to meet the phase equilibrium condition is as follows:(1) The reactance properties of Xce and Xeb are the same, but the reactance properties of Xcb are opposite. That is, ce and be are the same resisting piece, and cb resisting piece.(2) The oscillation frequency should satisfy 1Xo+Xcl-XolBased on this criterion, it can be quickly judged whether the oscillating circuit composition is reasonable or not.Three-terminal LC oscillatorThe three-terminal LC oscillation circuit is often used, and its operating frequency is about a few MHz to a few hundred MHz. The frequency stability is also higher than that of the transformer coupled oscillation circuit, which is about 10-3~10-4. After some frequency stabilization measures, it can be higher. There are many types of three-terminal LC oscillators, mainly: Inductance three-terminal type, also known as Hartley oscillator; capacitor three-terminal type, also known as Colpitts oscillator; series type improved capacitor three-terminal type, also known as Clapp parallel type improved capacitor three-terminal type , Also known as Sellier oscillator. The three-terminal oscillator has two basic circuits, as shown in the figure below.Figure8. Capacitive Feedback Oscillator and Inductive Feedback Oscillator2.2 Capacitive Feedback OscillatorCapacitive feedback three-terminal oscillator is an electronic component, also called Colpitts oscillator, which is a kind of self-excited oscillator. It is composed of a series capacitor, an inductance circuit and a positive feedback amplifier. It is named because the three end points of the two series capacitors of the oscillating circuit are connected to the three pins of the oscillating tube respectively.Figure9. Capacitive Feedback OscillatorAs shown in the figure, use C2 to feed back part of the voltage of the resonant tank to the base. The three end points of the LC resonant tank are respectively connected to the three electrodes of the transistor, so it is called a capacitive feedback three-terminal oscillator, or Colpitts oscillator. The vector analysis method can be used to prove that the circuit meets the phase balance condition. As long as the ratio of C1 and C2 is appropriately selected and the amplifier has enough amplification, the circuit can oscillate.Figure10. Capacitive Feedback OscillatorAdvantages of Colpitts circuit:(1) Good oscillation waveform;(2) The frequency stability of the circuit is high. If the capacitance of the circuit is increased appropriately, the influence of unstable factors on the oscillation frequency can be reduced;(3) The operating frequency of the three-terminal circuit of the capacitor can be made higher. The output and input capacitors of the oscillator tube can be directly used as the oscillation capacitor of the loop, and the operating frequency can reach a very high frequency range of tens of MHz to hundreds of МHz. Disadvantages of Colpitts circuit:When adjusting C1 and C2 to change the oscillation frequency, the feedback coefficient will also change, which will affect the starting conditions and working status. But as long as a variable capacitor is connected to both ends of L and C1 and C2 are fixed capacitors, the feedback coefficient will not be affected when the frequency is adjusted.2.3 Inductive feedback oscillator(1) Circuit compositionIn order to overcome the shortcomings that the transformer primary coil and the secondary coil in the transformer feedback oscillation circuit are not tightly coupled, the N1 and N2 of the transformer feedback oscillation circuit can be combined into one coil. As shown in the figure below, in order to strengthen the resonance effect, the capacitor C is connected across the entire coil. This is the inductive feedback oscillator circuit, or Harley oscillator.Figure11. Inductive Feedback Oscillator Circuit(2) Working principle✿The circuit includes four parts: amplifier circuit, frequency selection network, feedback network and non-linear element (transistor), and the amplifier circuit can work normally.✿Use the instantaneous polarity method to judge whether the circuit meets the phase condition of sine wave oscillation: disconnect the feedback, add the input voltage with frequency f0, give its polarity, and judge that the polarity of the feedback voltage obtained from N2 is the same as the input voltage , So the circuit satisfies the phase condition of sine wave oscillation.✿As long as the circuit parameters are selected properly, the circuit can meet the amplitude condition and produce sine wave oscillation. The following figure shows the AC path of the inductive feedback oscillation circuit. The three ends of the primary coil are connected to the three poles of the transistor, so the inductive feedback oscillation circuit is called an inductive three-point circuit.Figure12. AC Path of Inductive Feedback Oscillator Circuit(3) Advantages and disadvantagesThe coupling between N2 and N1 in the inductance feedback oscillation circuit is tight, the amplitude is large, and it is easy to oscillate; when C uses a variable capacitor, a wide adjustment range of oscillation frequency can be obtained, and the highest oscillation frequency can reach tens of MHz. Since the feedback voltage is taken from inductance, it has greater reactance to high-frequency signals, and the feedback signal contains more high-order harmonic components, and the output voltage waveform is not good. The following introduces two improved capacitor three-terminal oscillation circuits:Clap oscillator:The following figure (a) is the principle circuit of the Krapper oscillator, and (b) is its AC equivalent circuit. Its characteristic is that a capacitor C3 is added to the inductance branch of the aforementioned capacitive three-point oscillating resonant tank. Its value is relatively small, requiring C3<< C1, C3<< C2.Figure13. Clapp OscillatorRegardless of the influence of the capacitance between the poles, the total capacitance CΣ of the resonant circuit is the series connection of C1, C2 and C3, namely. Thus, the oscillation frequency is .The condition for the above formula to be true is that C1 and C2 must be selected relatively large. It can be seen that the influence of C1 and C2 on the oscillation frequency is significantly reduced, so the influence of the capacitance between the transistors connected in parallel with C1 and C2 is also very large. It is smaller, and the stability of the oscillation frequency is improved. Sellier oscillator:Figure14. Sellier Oscillator so the oscillation frequency:L is the inductance of the inductance coil of the resonant amplifier circuit; C is the total capacitance of the resonant circuit. In the LC resonance circuit, the inductance L(H)/capacitance C(F)=105~106, which can achieve better results.III RC Oscillator Circuit3.1 Brief Introduction of RC Oscillator and its Circuit● What is an RC oscillator?(1) The sine wave oscillator has no input signal and is a positive feedback amplifier with a frequency selection network. If resistors and capacitors are used to form a frequency selection network, it is called an RC oscillator, which is generally used to generate 1Hz-1MHz low-frequency signals. The frequency selection effect of the RC frequency selection network is not as good as that of the LC resonant circuit, so the waveform and stability of the RC oscillator are worse than that of the LC oscillator.(2) RC oscillator can be divided into sine wave oscillator and non-sine wave oscillator according to whether the output wave type is sine wave.(3) There are many kinds of RC oscillation circuits: bridge type, phase shift type, double T type, the most commonly used is bridge type oscillation circuit, namely RC series-parallel frequency selection network. ● Features of RC oscillator(1) RC phase-shift oscillator features: simple, poor frequency selection, unstable amplitude, inconvenient frequency adjustment, generally used in occasions with fixed frequency and low stability requirements. Frequency range: several hertz-tens of kilohertz(2) RC series-parallel network oscillator features: it can easily and continuously change the oscillation frequency, it is convenient to add negative feedback to stabilize the amplitude, and it is easy to get a good oscillation waveform.(3) Double T frequency selective network oscillator characteristics: good frequency selection characteristics, difficult frequency modulation, suitable for generating single frequency oscillation. ● RC oscillator circuitThe oscillating circuit composed of RC frequency selection network is called RC oscillating circuit, which is suitable for low-frequency oscillation, and is generally used to generate low-frequency signals of 1Hz~1MHz. The circuit is composed of four parts: amplifier circuit, frequency selection network, positive feedback network, and amplitude stabilization link. The main advantage is simple structure, economic and convenient. According to the different forms of the RC frequency selection network, the RC oscillator circuit can be divided into an RC lead (or lag) phase shift oscillator circuit and a Wien circuit oscillator circuit. For RC oscillator circuits, increasing the resistance R can reduce the oscillation frequency, and increasing the resistance does not need to increase the cost. The frequency of the sine wave generated by the commonly used LC oscillator circuit is relatively high. If a sine wave with a lower frequency is to be generated, the oscillation circuit must have a larger inductance and capacitance. This will not only cause the components to be bulky, heavy and inconvenient to install, but also difficult to manufacture. high cost.  Therefore, the sinusoidal oscillation circuit below 200kHz generally adopts an RC oscillation circuit with a lower oscillation frequency.3.2 RC Phase Shift OscillatorThe phase shift oscillator is an oscillator composed of an advanced phase shift or a lag phase shift circuit as a frequency selection network and an inverting amplifier. It has the advantages of simple circuit, economy and convenience, but the effect of frequency selection is poor, the amplitude is not stable enough, and the frequency adjustment is inconvenient. Therefore, it is generally used for occasions with fixed frequency and low stability requirements. Its oscillation frequency is:Figure15. RC Phase Shift Oscillator Schematic Diagram3.3 Wien Bridge OscillatorThe RC series-parallel frequency selection network and amplifier can be combined to form an RC oscillator circuit, and the amplifier part can be an integrated operational amplifier. As shown in the figure, the RC series-parallel frequency selection network is connected between the output of the operational amplifier and the non-inverting input to form positive feedback. Rt and R1 are connected between the output of the operational amplifier and the inverting input to form negative feedback. . The positive feedback circuit and the negative feedback circuit constitute a Wien bridge circuit, and the input and output ends of the operational amplifier are respectively connected across the diagonal of the bridge. Therefore, this kind of oscillation circuit is called a Wien bridge oscillation circuit.Figure16. Wien Bridge OscillatorThe oscillating signal is input from the non-inverting terminal, so a non-inverting amplifier is formed. The output voltage is in phase with the input voltage, and the closed-loop voltage amplification factor is equal to: When the RC series-parallel frequency selection network is ω=ω0=1/RC, Fu=1/3, εf=0, so as long as |Au|=1+(Rt/R1)>3, that is, Rt>2R1, oscillation The circuit can meet the self-excited oscillation amplitude and phase start-up conditions to produce self-excited oscillation, the oscillation frequency f0=1/2πRC. Using double adjustable potentiometer or double adjustable capacitor can easily adjust the oscillation frequency. In the commonly used RC oscillator circuit, the high stability capacitor is generally used to switch the frequency band (coarse frequency adjustment), and then the double variable potentiometer is used to fine-tune the frequency.IV Quartz Crystal Oscillator Circuit4.1 What is a Quartz Crystal Oscillator?Quartz crystal oscillator refers to a device made on the principle that the crystal resonates due to the piezoelectric effect when the frequency of the electrical signal is equal to the natural frequency of the quartz crystal. It is a key component of crystal oscillators and narrow-band filters.Although the appearance, size and frequency of the quartz crystal oscillator are different, the structure principle is basically the same. In order to improve the stable and reliable operation of the quartz crystal, the shell components of the quartz crystal oscillator will be sealed and evacuated. Or fill with nitrogen.4.2 Quartz Crystal(1) StructureFigure17. Structure of the Quartz Crystal(2) Basic characteristicsApplying an electric field between the plates→mechanical deformation of the crystalMechanical force is applied between the plates → the crystal generates an electric fieldPiezoelectric effect: alternating voltage → mechanical vibration → alternating voltageWhen the alternating voltage frequency = natural frequency, the amplitude is the largest → piezoelectric resonanceThe natural frequency of mechanical vibration is related to the size of the wafer, and the stability is high.4.3 Quartz Crystal Oscillator CircuitThe high quality factor of quartz crystal is used to form an LC oscillator circuit.(1) Parallel Type quartz crystal oscillatorFigure18. Parallel Type Quartz Crystal Oscillator Quartz crystal works between fs and fp, which is quite a large inductance, and forms a capacitive three-point oscillator with C1 and C2. Because the Q value of the quartz crystal is very high, which can reach more than several thousand, the circuit can obtain high oscillation frequency stability.Figure19. Frequency Characteristics of Parallel Quartz Crystal Oscillator (2) Series type quartz crystal oscillatorFigure20. Series Type Quartz Crystal Oscillator Circuit The quartz crystal works at fs, which is resistive and has the smallest impedance, the strongest positive feedback, and zero phase shift, which meets the phase balance condition of oscillation.For frequencies other than fs, the impedance of the quartz crystal increases, and the phase shift is not zero, then the oscillation condition is not met, and the circuit does not oscillate.Figure21. Frequency Characteristics of Series Quartz Crystal OscillatorV Non-sine Wave Generating Circuit5.1 What is a Non-sine Wave Generating Circuit?It is composed of an integrating circuit and a hysteresis comparator circuit. The role of the integrator circuit is to produce a transient process. The hysteresis comparator acts as a switch, that is, the steady state is destroyed by the continuous closing of the switch, and a transient process is generated.Commonly used non-sine wave generating circuits include rectangular wave generating circuits, triangular wave generating circuits and sawtooth wave generating circuits, etc. They are often used as signal sources in pulse and digital systems.5.2 Rectangular Wave GeneratorIt is composed of hysteresis comparison circuit and RC timing circuit. The output has no steady state and there are two transient states; if the output is high level, it is defined as the first transient state, and the output is low level as the second transient state.Basic components:(1) Switching circuit: The output has only two situations of high level and low level, called two states; therefore, a voltage comparator is used.(2) Feedback network: self-control, when the output is in a certain state, it breeds the condition of turning into another state. Feedback should be introduced.(3) Delay link: Make the two states maintain a certain period of time and determine the oscillation frequency. Use RC circuit to achieve.Circuit composition:Figure22. Rectangular Wave Generating Circuit5.3 Triangle Wave and Sawtooth Wave Signal GeneratorThe circuit structure of the triangle wave generator: hysteresis comparator + inverting integratorworking principle:Figure23. Circuit of Triangle Wave Generator Sawtooth wave generator: change the forward and reverse charging time constant of the integrator, thereby changing the duty cycle.Figure24. Circuit Diagram of Sawtooth Generator uo1=+UZ, D is cut off, charging time constant: R4C.uo1=-UZ, D is on, charging time constant: (R6∥R4)C≈R6C.Figure25. The Waveform of the Sawtooth GeneratorVI QuizLC resonant circuits are used in:a) RF and ultrasonic oscillators.b) AF and ultrasonic oscillators.c) LF sweep oscillators.d) Variable frequency crystal oscillators. Answer: aⅦ FAQ1. What are the uses of an oscillator?Oscillators have very high precision and accuracy usually <100 ppm variation at a max. So with this kind of accuracy, the oscillator can be used as a clock of the microcontroller (the clock is the most essential part of the microcontroller, without an accurate clock, the functionality will be erratic because we cannot expect the output at the same time we have designed it for). All the quartz-based watches use an Oscillator (32kHz quartz crystal) to keep the time. SO if your timekeeping devices are running with an oscillator, you can imagine the accuracy.Oscillators can additionally be used to generate waveforms required in test benches. In almost all the applications where timing and synchronization are very essential, an oscillator finds its place. For example, in communication systems (whichever electronic communication you consider let it be a telephone, lan, anything) an oscillator is the heart.An oscillator can be used in power systems to generate accurate power waveforms. 2. What is the function of a local oscillator?A local oscillator is used in transmitters and receivers to add or subtract an amount to a basic carrier and modulation. Very handy, as it’s easiest to build up a carrier and modulate it at a low frequency, like 445Kc or 10.7MHz, and then add to it a “LO” to get it up to the FM band or the Gigahertz Wifi or radar bands. The same thing on receive, you first use a 'LO' to subtract down to an intermediate frequency where it’s so much easier to amplify and filter. 3. How do you make a crystal oscillator?The simplest is to use a logic inverter. Put a crystal between the input and output. Some schematics show some caps from the crystal legs to the ground and some show a series resistor. 4. Which type of circuit is used in the oscillator?Types of Oscillators: Harmonic Oscillators & Crystal Oscillators. Harmonic or linear oscillators produce a sinusoidal output where a signal increases and decreases at a predictable level over time. Two basic types are RC, or resistor/capacitor circuits, as well as LC, or inductor-capacitor circuits. 5. What is an Oscillator and the types of oscillators?An oscillator is a type of circuit that controls the repetitive discharge of a signal, and there are two main types of the oscillator; a relaxation, or a harmonic oscillator. This signal is often used in devices that require a measured, continual motion that can be used for some other purpose. 6. What is the basic principle of an oscillator?There are many types of electronic oscillators, but they all operate according to the same basic principle: an oscillator always employs a sensitive amplifier whose output is fed back to the input in phase. Thus, the signal regenerates and sustains itself. This is known as positive feedback. 7. What is the working of the oscillator?Oscillators convert direct current (DC) from a power supply to an alternating current (AC) signal. They are widely used in many electronic devices ranging from simplest clock generators to digital instruments (like calculators) and complex computers and peripherals etc. 8. How does an oscillator work without input?An oscillator circuit uses a vacuum tube or a transistor to generate an AC output. ... For continuously generating output without the requirement of any input from the preceding stage, a feedback circuit is used. From the above block diagram, the oscillator circuit produces oscillations that are further amplified by the amplifier. 9. What causes oscillation?If a constant force such as gravity is added to the system, the point of equilibrium is shifted. ... In the spring-mass system, oscillations occur because, at the static equilibrium displacement, the mass has kinetic energy which is converted into potential energy stored in the spring at the extremes of its path. 10. What is the difference between oscillator and inverter?The oscillator is a generalized term for an active circuit that produces a periodic waveform. The inverter is a specialized term for a system that contains an oscillator and produces large amounts of power(such as AC) from a source (like a DC battery). The oscillator has no input and produces an oscillating wave as output. 
kynix On 2020-07-31   10490
Resistors

Operational Amplifier Applications, Op-amp Basics

Ⅰ IntroductionAs for operational amplifier applications, in electronic circuit, it is usually combined with a feedback network to form a certain functional module, with a special coupling circuit and feedback. Its output signal can be input signal addition, subtraction or differentiation, integration, etc, which early used in analog computers to do mathematical operations. Now they widely used in the electronics industry, regarded as precision AC and DC amplifiers, active filters, oscillators and voltage comparators.This Video is Introducing Operational Amplifier Applications in the CircuitCatalogⅠ Introduction1.1 Integrated Op AmpⅡ Op-amp ParametersⅢ Application MattersⅣ Classic Amplifier CircuitsⅤ One Question Related Op Amp and Going Further5.1 Question5.2 Answer1.1 Integrated Op Amp1.1.1 Evaluation AnalysisIntegrated operational amplifiers are one of the most widely used devices in analog integrated circuits. In various systems, because of different application requirements, the performance requirements of operational amplifiers are also different.Where there are no special requirements, try to use a universal integrated operational amplifier as much as possible, which can reduce costs and easily replace. When using multiple op amps in a system, use as many op amp integrated circuits as possible. For example, LM324 and LF347 always integrate four op amps together in a circuit.The evaluation of integrated op amps depends on their overall performance. Generally, the merit coefficient K is used to measure the excellent degree of integrated operational amplifiers, which is defined as: where SR is the slew rate and the unit is V / ms. The larger the value, the better the AC characteristics of the operational amplifier; The input bias current of the amplifier is lib, the unit is nA; VOS is the input offset voltage in mV. The smaller the Iib and VOS values, the better the DC characteristics of the op amp. Therefore, for circuits that amplify AC signals such as audio and video, op amps with large SR are better; for circuits that handle weak DC signals, op amps with high accuracy are more suitable (both offset current, offset voltage and temperature drift are relatively small).When selecting an integrated op amp, some factors should be considered in addition to the figure of merit coefficient K. For example, the signal source is a voltage source or a current source; the nature of the load, and whether the output voltage and current of the integrated op amp meet the requirements; operating voltage range, power consumption, and volume of the integrated op amp.Figure 1. Using Operational Amplifier as a Comparator1.1.2 Integrated Op Amp Basics Power supplyThe integrated op amp has two power terminals + VCC and -VEE, with different power supply methods. For different power supply modes, the requirements for input signals are different.1) Dual power supplyOp amps are mostly powered in this way. The positive power (+ E) and negative power (-E) relative to the common terminal (ground) are connected to the + VCC and -VEE pins of the op amp, respectively. In this way, the signal source can be directly connected to the input pin of the op amp, and the amplitude of the output voltage can make the positive and the negative symmetrical.2) Single power supplySingle-supply operation connects the -VEE pin of the op amp to ground. At this time, in order to ensure that the internal unit circuit of the operational amplifier has a suitable static operating point, a DC potential must be added to the input end of the op amp. Zero settingDue to the influence of the input offset voltage and input offset current of the integrated op amp, when the input signal is zero, the output is often not equal to zero. In order to improve the operation accuracy of the circuit, it is required to compensate the error caused by the offset voltage and the offset current. This is the zero setting of the operational amplifier. Commonly used zeroing methods include internal zeroing and external zeroing. For integrated op amps without internal zeroing terminals, external zeroing methods should be used. Self oscillationThe operational amplifier is a high-amplitude multi-stage amplifier. Under the condition of deep negative feedback, it is easy to cause self-excited oscillation. To make the amplifier work stably, a certain frequency compensation network must be added to eliminate the self oscillation. In addition, to prevent low-frequency oscillation or high-frequency oscillation caused by the internal resistance of the power supply, an electrolytic capacitor (10mF) and a high-frequency filter capacitor (0.01 mF ~ 0.1mF) should be connected. Device protectionThere are three aspects to the protection of the integrated op amp safety: power protection, input protection and output protection.1) Power protectionCommon faults of power supply are reverse polarity and voltage jump. For a power supply with poor performance, voltage overshoot often occurs at the moment when the power is turned on and off. Protection measures such as the use of FET current source and voltage regulator clamping protection. The voltage regulator’s voltage value is greater than the normal operating voltage of the integrated op amp and less than the maximum allowable operating voltage of the integrated op amp, and the current of the FET tube should be greater than the normal operating current of integrated op amp.2) Input protectionIf the input differential/common mode voltage of the integrated op amp is too high beyond the limit parameter range of the integrated op amp, it will be damaged.3) Output protectionWhen the integrated op amp is overloaded or the output is shorted, the op amp will be damaged if there is no protection circuit. However, some integrated op amps have internal current limit protection or short circuit protection, and no additional output protection is required to use these devices.Figure 2. An Inverting Op Amp CircuitⅡ Op-amp ParametersTo use the op amp better in the circuit, you must have a certain understanding of its internal parameters. Here are the technical parameters closely related to the op amp: Unity-gain bandwidth Definition: Under the condition that the closed-loop gain of the op amp is 1 time, a constant amplitude sinusoidal small signal is input to the input end of the op amp, and the closed-loop voltage gain measured from the output end of the op amp is reduced by 3dB (or equivalent to 0.707 times of the input signal of the op amp), that is to say, the frequency at which the output signal is reduced by -3dB is unity-gain bandwidth. It is a very important indicator. For a sinusoidal small signal amplification, the unity-gain bandwidth is equal to the product of the input signal frequency and the maximum gain at that frequency. In other words, when you know the frequency and gain of the signal to be processed, the unity-gain bandwidth (gain bandwidth = amplification * signal frequency) can be calculated to select the appropriate op amp. The higher the bandwidth, the higher the frequency of the signal that can be processed, and the better the high frequency characteristics, otherwise the signal will be easily distorted.    For small signals, the unity-gain bandwidth is also called the gain-bandwidth product, which can roughly show the ability of the op amp to process the frequency of the signal. For example, the gain bandwidth of a certain operational amplifier is 1MHz, if the actual closed-loop gain is 100, then the maximum frequency for theoretical processing of small signals is 1MHz / 100 = 10KHz.For the bandwidth of a large signal, that is, the power bandwidth, the influence of the slew rate SR is the major factor, and the unit is V/uS. In this case, the power bandwidth calculated by FPBW = SR / 2πVp-p, that is, the gain bandwidth and power bandwidth must be satisfied at the same time when designing the circuit.For DC signals, bandwidth issues are generally not considered, and accuracy and interference are mainly considered.When the amplification factor of an amplifier is n times, it does not mean that all input signals are amplified n times. When the signal frequency increases, the amplification capability decreases. Open bandwidthThe open-loop bandwidth is defined as: inputting a constant-amplitude sinusoidal small signal to the input of the op amp, the frequency measured at which the open-loop voltage gain decrease 3dB from the output of the op amp to the dc gain of the op amp. This is used for very small signal processing. Slew rate SRWith the op amp connected in a closed loop, a large signal (including a step signal) is input to the input of the op amp, and the output rise rate of the op amp is measured from the output of the op amp called SR. Because the input stage of the op amp is switched during the conversion, the feedback loop of the op amp does not work, that is, the conversion rate is independent of the closed-loop gain. The slew rate is a very important index for large signal processing. For general op amps, the slew rate SR <= 10V / μs, and the slew rate of high speed op amps is SR> 10V / μs. The highest conversion rate SR of current high-speed op amps reaches 6000V / μs. The larger the SR, the better the response of the op amp to the input signal changing at high speed. The larger the signal amplitude, the higher the frequency, and the greater the SR. This is used for op amp selection in large signal processing. Full-power bandwidthAt the rated load, under the condition that the closed-loop gain of the op amp is 1 time, a constant-amplitude sinusoidal large signal is input to the input end of the op amp, so that the output frequency of the op amp reaches the maximum (allowing certain distortion) signal. This frequency is limited by the slew rate SR of the op amp. Approximately, full power bandwidth is calculated by formula SR / 2πVop (Vop is the peak output amplitude of the op amp). It is a very important indicator for op amp selection in large signal processing. Setting timeAt the rated load, under the condition that the closed-loop gain of the op amp is 1 time, the time required to input a step large signal to the input of the op amp to increase the output from 0 to a given value. Because it is a step large signal input, a certain jitter will occur after the output signal reaches a given value. This jitter time is called the stabilization time. At this moment, stabilization time + rise time = settling time. For different output accuracy, there is a big difference in the stabilization time. The higher the accuracy, the longer the stabilization time. Equivalent input noise voltageIt refers to any AC random interference voltage generated at the output of an op amp with good shielding and no signal input. When this noise voltage is converted to the input of the op amp, it is called the input noise voltage of the op amp (sometimes expressed by noise current). For broadband noise, the effective value of the input noise voltage of ordinary op amps is about 10 ~ 20μV. This value often corresponds to a certain frequency band. Output impedanceIt refers to the ratio of the change in voltage to the corresponding change in current when the signal voltage is applied to the output of the op amp working in the linear region. At low frequencies it only refers to the output resistance of the op amp. Common mode input resistenceRefers to the ratio of the change in the input voltage of the common mode to the corresponding change in the input current when the two inputs of the op amp input the same signal. At low frequencies, it behaves as a common mode resistance. Generally, the common mode input impedance of the op amp is much higher than the differential mode input impedance, with a typical value above 108Ω. Common mode rejection ratioSame as the definition in the differential amplifier circuit, it is the ratio of the differential mode voltage gain to the common mode voltage gain, which is usually expressed in decibels. It is a parameter that measures the degree of symmetry of the input stage differential amplifier and the ability of the integrated op amp to suppress common mode interference signals. The larger the value, the better. Power supply rejection ratioThe power supply voltage rejection ratio is defined as the change ratio of the input offset voltage of the op amp with the power supply voltage in the linear region. The power supply voltage rejection ratio reflects the effect of power supply changes on the output of the op amp. At present, the power supply voltage suppression ratio is only about 80dB. Therefore, when used for DC signal or small signal processing for analog amplification, the power supply of the op amp needs to be carefully set. Of course, an op amp with a high common mode rejection ratio can compensate a part of the power supply voltage rejection ratio. In addition, when using dual power supplies, the power supply voltage rejection ratio of the positive and negative power supplies may be different. Differential mode input resistanceRefers to the ratio of the change in voltage at the two input terminals to the corresponding change in current at the input terminals when the op amp is operating in the linear region. The differential mode input impedance includes the input resistance and input capacitance, and refers only to the input resistance at low frequencies. General products specification only give input resistance. The input resistance of the op amp using the bipolar transistor as the input stage is not greater than 10MΩ; the input resistance of the op amp as the input stage of the field effect transistor is generally greater than 109Ω. Input offset voltageWhen the input voltage is zero, the output voltage is divided by the voltage gain, plus the negative sign, which is the offset voltage converted to the input. It is the compensation voltage applied at the input when the output voltage is zero. The input offset voltage actually reflects the circuit symmetry inside the op amp. The better the symmetry, the smaller the input offset voltage. The input offset voltage is a very important indicator of the op amp, especially when it is a precision op amp or used for DC amplification.The input offset voltage has a certain relationship with the manufacturing process. It is between ± 1 and 10 mV when op amps use the bipolar process (that is, the standard silicon process). If the field effect tube is used as the input stage, it will be greater. For precision op amps, it is generally below 1mV. The smaller the input offset voltage, the smaller the intermediate zero offset during DC amplification, and the easier it is to handle. Therefore, it is an extremely important index for precision op amps. Input offset voltage driftWithin the specified operating temperature range, it is the ratio of the change in input offset voltage with temperature to the change in temperature. It is actually a supplement to the input offset voltage, which is convenient for calculating the drift of the amplifier circuit due to temperature changes within a given operating range. It is an important indicator for measuring the temperature effect to the op amp. Under normal circumstances, it is about (10 ~ 30) uV / C (degree Celsius), the high quality can be <0.5uV / C. Input offset currentIt is defined as the difference between the base current of the differential pair of the differential input stage when the output DC voltage of the op amp is zero. Used to characterize the degree of asymmetry of the differential input current. The better the symmetry, the smaller the input offset current. Input offset current is a very important indicator for op amps, especially for precision operational amplifier or DC amplifier. The input offset current is approximately one to one-tenth of the input bias current. It has an important impact on small signal precision amplification or DC amplification, especially when a large resistor is used outside the op amp. The effect of input offset current may exceed the effect of input offset voltage on accuracy. The smaller the input offset current, the smaller the intermediate zero offset during DC amplification, and the easier it is to handle. Therefore, it is an extremely important index for precision op amps. Input offset current temperature driftWithin the specified operating temperature range, the ratio of the amount of change in input offset current with temperature to the amount of temperature change. It refers to the temperature coefficient of within the specified operating range, and is also an important indicator to measure the temperature effect on the op amp. It is usually about (1-50) nA / C, and the high quality is about several pA / C. This value is only given in the precision op amp parameters, and it needs attention when it is used for DC signal processing or small signal processing. Input bias current   It is defined as the average value of the bias currents of the two input terminals when the output DC voltage of the op amp is zero, in other words, it is the average current flowing into the input terminal when the operational amplifier is operating in the linear region. The input bias current has a greater impact on the places where input impedance is required, such as high-impedance signal amplification and integrator circuits. The input bias current has a certain relationship with the manufacturing process. If a field effect tube is used as the input stage, the input bias current generally lower than 1nA. It always used to measure the input current of the differential amplifier pair. Maximum differential mode input voltageIt is a voltage that the two input ends of the op amp can withstand. When it is exceeded, the reverse breakdown of the differential tube will occur. The NPN tube made by the plane process has a value of about 5V, and the Vidmax of the horizontal PNP tube can reach more than 30V. Maximum common mode input voltageIt an allowable range of common mode input voltage under normal operating conditions of the op amp. When the input differential pair saturates, the amplifier loses common mode rejection ability. In the case of interference, it is necessary to pay attention to this problem in the use of the circuit. Output peak to peak voltageWorking in the linear region, under the specified load, when the op amp is powered by the large power supply, it is the maximum voltage amplitude that the op amp can output. Except for low voltage op amps, the output peak-to-peak voltage of general op amps is greater than ± 10V, but less than the power supply voltage. This is due to the design of the output stage. The output stage of modern low-voltage op amps has been specially treated. The output peak-to-peak voltage is close to within 50mV of the power supply voltage, so it is called a full-scale output op amp, also known as a rail-to-raid op amp. It should be noted that the output peak-to-peak voltage of the op amp is related to the load, and the value is different for different loads; the positive and negative output voltage swings of the op amp are not necessarily the same. For practical applications, the closer the output peak-to-peak voltage is to the supply voltage, the easier the power supply design.Figure 3. Input Offset Voltage of an Op-ampⅢ Application Matters1) A single-supply op amp must be DC biased, otherwise it will not work properly. For the virtual ground design, in addition to the DC potential, it is necessary to pay attention to the voltage stabilization (it is best to use the reference voltage chip), and also to ensure low impedance AC decoupling, that is, low-frequency decoupling parallel to at least 10uF and high frequency decoupling under 0.1uF.2) The input of the non-inverting amplifier must be biased to ground as a DC path.3) Ordinary op amps cannot directly drive capacitive loads. If there is need, you must use capacitors for phase compensation or output series resistors and then connect the load.4) For the op amp input of the external interface, a TVS tube must be connected in parallel to the positive and negative input pins to prevent the op amp from reversing the polarity due to the too large input voltage signal, forming a parasitic false signal output.5) For amplifier circuits with a gain of more than 10 times, pay attention to controlling the bandwidth gain of the op amp to prevent the device from self oscillation.6) The output of the power amplifier needs to be protected by switching diodes to the power supply and ground, especially when inductive loads are connected.7) When using multiple op amps to process multiple signals, care must be taken to prevent the instantaneous changes in one of the signals from causing crosstalk to the other signal. Therefore, it is recommended not to use one op amp to process multiple signals.8) Most op amp chips are ESD sensitive devices, so pay more attention when using them.9) The pins of unused op amps (excess channels in multiple op amps) should not be left floating, and  grounded or connected to positive and negative power supplies. It is recommended to connect it as a follower (the output is connected to the reverse input) and the non-inverting input is connected to a potential between the power rails (the ground of the dual power system or any suitable point in the circuit). They can also used as buffer amplifiers and add them to a small impact location in the system.Figure 4. Op Amp 741Ⅳ Classic Amplifier CircuitsFigure 5. Inverting AmplifierFigure 5: The grounded non-inverting terminal of op amp is 0V. The inverting and non-inverting terminals are short-circuit, so the inverting end is also 0V. The input resistance of the inverting input terminal is very high, and it is virtual open. In other words, there is almost no current pass through. Therefore, the current flowing through each component in a series circuit is the same, that is, the current flowing through R1 and R2 are the same.Current flowing through R1: I1 = (Vi-V-)/R1Current flowing through R2: I2 = (V--Vout)/R2V- = V+ = 0, I1 = I2Solve the above algebraic equation to get Vout = (-R2/R1)*Vi, it is the input-output relationship of the inverting amplifier. Figure 6. Non-inverting AmplifierIn Figure 6, Vi and V- are virtual short, where Vi = V-. Because of the virtual open, there is no current flow through at the reverse input terminal, then R1=R2. If the current is I, which is obtained by Ohm's law: I = Vout/(R1+R2);Vi is equal to the partial voltage on R2, that is: Vi = I*R2.Virtual short: Vi = V-, R1=R2Ohm's law: I = Vout/(R1+R2), Vi = I*R2Where Vout=Vi*(R1+R2)/R2, represents the non-inverting amplifier. Figure 7. AdderFigure 7: Knowing from the Kirchhoff's law and virtual open theory, the sum of the current through R2 and R1 is equal to the R3, V- = V+ = 0 (short circuit), so (V1 – V-)/R1 + (V2 – V-)/R2 = (Vout – V-) /R3 can be transferred as V1/R1 + V2/R2= Vout/R3. If R1=R2=R3, then the formula becomes Vout=V1+V2, which is an adder. Figure 8. AdderIn Figure 8, because of the virtual open, no current flows through the non-inverting terminal, where V+ = V-, R1=R2, R4=R3, therefore, (V1 – V+)/R1 = (V+-V2)/R2, (Vout – V-)/R3 = V-/R4 can be simplified as V+ = (V1 + V2)/2 V- = Vout/2. So Vout = V1 + V2 is also an adder. Figure 9. SubtractorFigure 9 shows that the current through R1 is equal to the R2, and R4=R3, therefore, (V2– V+)/R1 = V+/R2, (V1 – V-)/R4 = (V--Vout)/R3. If R1=R2, then V+ = V2/2; if R3=R4, then V- = (Vout + V1)/2, because of V+ = V-, so Vout =V2-V1 is a subtractor. Figure 10. Integrator CircuitIn Figure 10, the input voltage at the inverting terminal is equal to the non-inverting terminal because of short circuit; the current through R1 is equal to the C1 because of virtual open. The current flowing through R1 and C1 are Ri=V1/R1, Ci=C*dUc/dt=-C*dVout/dt, respectively. So Vout=((-1/(R1*C1))∫V1dt, which is a integrator circuit. If V1 is a constant voltage U, then the above formula is transformed to Vout = -U*t/(R1*C1)t, then the Vout is a straight line that changes with time. Figure 11. Differential CircuitIn Figure 11, the current through capacitor C1 and resistor R2 is equal because of virtual open; V+ = V- because of short circuit, where Vout = -i * R2 = -(R2*C1)dV1/dt, which is a differential circuit. If V1 is a DC voltage, the output Vout corresponds to a pulse in the opposite direction to V1. Figure 12. Differential Amplifier CircuitFigure 12:Vx = V1……a, Vy = V2……bthen R1, R2, R3 can be regarded as a series, R1=R2=R3, the current I=(Vx-Vy)/R2……cwhere Vo1-Vo2=I*(R1+R2+R3) = (Vx-Vy)(R1+R2+R3)/R2 ……dIf R6=R7, then Vw = Vo2/2 ......e, similarly, if R4=R5, then Vout – Vu = Vu – Vo1, so Vu = (Vout+Vo1)/2 ……fdue to short circuit, Vu = Vw ……g, based on efg formulas, Vout = Vo2 – Vo1 ……hGet from dh, Vout = (Vy – Vx) (R1+R2+R3)/R2, where (R1+R2+R3)/R2 is a fixed value. This value determines the amplifier multiple of the difference (Vy-Vx), thus it is a differential amplifier circuit. Figure 13. Amplifier CircuitIt is a relatively common amplifier circuit. Many controllers accept 0~20mA or 4~20mA current from various measuring instruments. The circuit converts the current into voltage signal to become a digital signal by ADC. Figure 13 is such a typical circuit. As shown in Figure, 4~20mA current flows through the sampling 100Ω resistor R1, there will be a voltage difference of 0.4~2V on R1. Due to virtual open circuit, R3= R5 and R2=R4.Therefore: (V2-Vy)/R3 = Vy/R5 ……a  (V1-Vx)/R2= (Vx-Vout)/R4 ……bShort circuit: Vx = Vy ……cCurrent changes from 0~20mA, then V1 = V2 + (0.4~2) ……dPut cd formulas into b formula: (V2 +(0.4~2)-Vy)/R2 = (Vy-Vout)/R4 ……eIf R3=R2 , R4=R5, then e-a gets Vout =-(0.4~2)R4/R2 ……fIn Figure 13, R4/R2=22k/10k=2.2, then f formula Vout = -(0.88~4.4)V, that is to say, the current of 4~20mA is converted into a voltage range of -0.88~-4.4V. Current can be converted into voltage, and voltage can also be converted into current. Figure 14 is such a circuit. The negative feedback in the above figure does not directly feedback through the resistor, but the emitter junction of the transistor Q1 is connected in series. But it isn't a comparator. As long as it is an amplifying circuit, the law of short circuit and virtual open still conforms.Figure 14. Amplifier CircuitDue to virtual open, no current flows through the input of the op amp,Then (Vi – V1)/R2 = (V1 – V4)/R6 ……aSimilarly (V3 – V2)/R5 = V2/R4 ……bsince short circuit, V1 = V2 ……cIf R2=R6, R4=R5, then V3-V4=Vi can be obtained from abc.The above formula shows that the voltage across R7 is equal to the input voltage Vi, then the current through R7 is I=Vi/R7. If the load RL<100KΩ, the current through R1 and R7 are basically the same. Ⅴ One Question Related to Op Amp and Going Further5.1 QuestionWhat the Application of an Op Amp as a Phase Shifter?5.2 AnswerIn electronic circuit, op amp is used for direct coupling procedure and so DC voltage level at the emitter terminal increases from phase to phase. This rapidly increasing DC level is likely to shift the operating point of the upcoming stages. Thus to move down the increasing voltage swing, this phase shifter is applied.The phase shifter performs by adding a DC voltage level to the output of fall stage to pass the output to a ground level. Frequently Asked Questions about Operational Amplifier Applications1. Why is it called operational amplifier?It's called an “operational” amplifier because it performs a mathematical operation. The most obvious one is multiplication - it amplifies an input signal by a constant. ... But many different 'operations' can be performed by different circuit topologies. 2. What is inside an operational amplifier?Operations amplifiers — op-amps for short, are integrated circuits, constructed mostly out of transistors and resistors. These integrated circuits multiply an input signal to a larger output. You can use these components with voltage and current in both DC and AC circuits. 3. What are operational amplifiers used for?Op amps are used in a wide variety of applications in electronics. Some of the more common applications are: as a voltage follower, selective inversion circuit, a current-to-voltage converter, active rectifier, integrator, a whole wide variety of filters, and a voltage comparator. 4. What are linear applications of op amp?A linear amplifier like an op amp has many different applications. It has a high open loop gain, high input impedance and low output impedance. It has high common mode rejection ratio. Due to these favourable characteristics, it is used for different application. 5. How does an operational amplifier work?An operational amplifier, or op amp, generally comprises a differential-input stage with high input impedance, an intermediate-gain stage, and a push-pull output stage with a low output impedance (no greater than 100 Ω). ... That is, the output gets fed back to the inverting input through some impedance. 6. What do you mean by differential amplifier?A differential amplifier is a type of electronic amplifier that amplifies the difference between two input voltages but suppresses any voltage common to the two inputs. It is an analog circuit with two inputs and and one output in which the output is ideally proportional to the difference between the two voltages. 7. What are the non linear applications of op amp?Non-Linear Applications of Op AmpVoltage comparator.Two applications of comparator as window detector and zero crossing detector.Schmitt trigger circuit with the extension of regenerative comparator.Multivibrator circuits.Precision rectifier or super diode with the combination of op amp as voltage follower and a diode. 8. Why do we use differential amplifier?Differential amplifiers are used mainly to suppress noise. ... Noise is generated in the wires and cables, due to electromagnetic induction, etc., and it causes a difference in potential (i.e., noise) between the signal source ground and the circuit ground. 9. What does an operational amplifier do?An operational amplifier is an integrated circuit that can amplify weak electric signals. An operational amplifier has two input pins and one output pin. Its basic role is to amplify and output the voltage difference between the two input pins. 10. What is an ideal operational amplifier?Operational amplifier: The ideal op amp is an amplifier with infinite input impedance, infinite open-loop gain, zero output impedance, infinite bandwidth, and zero noise. It has positive and negative inputs which allow circuits that use feedback to achieve a wide range of functions.
kynix On 2020-03-20   6600
Resistors

Principle, Characteristics and Main Parameter of Thyristor

IntroductionThyristor, commonly known as silicon controlled rectifier(SCR), its normative term is reverse blocking three-terminal thyristor. Thyristors are high-power semiconductor devices that have both switching and rectifying functions, and are used in various circuits such as controllable rectification and frequency conversion, inverters, and non-contact switches. As long as it is provided with a weak point trigger signal, it can control the strong electric output. So it is a bridge for semiconductor devices to enter the field of strong electricity from the field of weak electricity. So far, thyristors are the most widely used semiconductor devices in the electronics industry. Despite the continuous emergence of various new semiconductor materials, 98% of semiconductor materials are still silicon materials, which are still the basis of the integrated circuit industry. It is widely used due to its small size, light weight, high power and long life.Intro to Thyristors: the SCRCatalogIntroductionⅠ Thyristor Basics1.1 Brief Introduction of Thyristor1.2 Working Principle of  ThyristorⅡ The Main Characteristics of Thyristors2.1 Basic Structure of Thyristor2.2 Volt-ampere Characteristics of Thyristors2.3 Static Characteristics of Thyristors2.4 Characteristic Equation of ThyristorⅢ The Main Parameters of Thyristor3.1 Main Parameters of Unidirectional Thyristors3.2 Main Parameters of TRIACⅣ Main Function of ThyristorⅠ Thyristor Basics1.1 Brief Introduction of ThyristorThyristor, also called silicon controlled rectifier, is an abbreviation of semiconductor thyristor. It is a high-current switching semiconductor device that uses small currents to control. There are two commonly used types: ordinary thyristors (also called unidirectional thyristors) and TRIAC(triode for alternating current). Because of its small size, light weight, high efficiency, long life, vibration resistance and because it is noiseless, easy to use, it has attracted great attention from domestic, foreign, industrial and agricultural production departments in a short period of time and has been widely used in various production equipment and household appliances. According to its working principle, it can be roughly divided into four categories: f— Rectification: change AC power into adjustable DC power. — Inverter: converts DC power to AC power with a certain frequency. — DC switch: used for DC loop switch or DC voltage regulation. — AC switch: used for AC loop switch or AC voltage regulation. According to its service objects, it can be used in industries, agriculture, national defense, transportation, mining, metallurgy, light industry, chemical industry and other departments.In performance, thyristors not only have unidirectional conductivity, but also have more valuable controllability than silicon rectifier elements (commonly known as "dead silicon"). It has only two states: on and off.Thyristors can control high-power electromechanical equipment with milliamp currents. If the frequency exceeds this value, the average switching current allowed to pass will decrease due to the significant increase in the switching losses of the components. At this time, the nominal current should be degraded.Thyristors have many advantages, such as: controlling high power with low power, power amplification multiples up to several hundred thousand times; extremely fast response, turn on and off in microseconds; non-contact operation, no spark, no noise; high efficiency, low cost and so on.Disadvantages of thyristors: poor static and dynamic overload capacity; easy to be misguided due to interference.The two types of thyristors, unidirectional thyristors and three-terminal TRIAC, are briefly introduced below.1.2 Working Principle of  Thyristora. Unidirectional ThyristorThe internal structure of the unidirectional thyristor is shown in figure 1 (a). It can be seen from figure 1 (a) that the unidirectional thyristor is composed of four layers semiconductors P1N1P2N2. There are three PN junctions in the middle: the junction J1, J2, and J3. The anode A is drawn from P1, the cathode K is drawn from N2, and the control electrode (or gate) G is drawn from the middle P2. The circuit symbol of the unidirectional thyristor is shown in figure 1 (b). Figure 1. Schematic Diagram and Circuit Symbol of Unidirectional ThyristorIn order to understand the working principle of the unidirectional thyristor, the unidirectional thyristor can be equivalently regarded as a combination of a PNP transistor T1 and an NPN transistor T2. The middle layer P2 and layer N1 are shared by two transistors. The anode A is equivalent to the emitter of T1, and the cathode K is equivalent to the emitter of T2, as shown in figure 2. Figure 2. Working Principle of Unidirectional ThyristorThe key to understanding how unidirectional thyristors work is to understand the role of the control electrode.(1) No voltage or reverse voltage is applied to the control electrodeWhen the control electrode is left floating or a reverse voltage is applied between the control electrode and the cathode, that is, UGK<0, there must be IG=0. If a reverse voltage is applied between the anode and the cathode, that is, UAK<0. Due to J, and J2, the transmitting junctions of T1, T2, are both reverse biased and T1 and T2 are in the off state, at this time, the current flowing through the unidirectional thyristor is only the reverse saturation current of the J1 and J3, IA≈0, and the unidirectional thyristor is in the blocking state; if a forward voltage is applied between the anode and the cathode, that is, UAK>0, J2 is in a reverse biased state, because IG=0, T2 must be in the off state. and the current in the unidirectional thyristor is only the reverse of J2. At this time, the current in the unidirectional thyristor is just the reverse saturation current of J2, IA≈0, and the unidirectional thyristor is still in the blocking state. Therefore, when no voltage is applied to the control pole or reverse voltage is applied, IG = 0, the unidirectional thyristor is in a blocking state, and has positive and negative blocking capabilities.(2) Apply forward voltage to the control electrodeWhen a forward voltage is applied between the control electrode and the cathode, that is, UGK> 0, the emitter junction J3 of T2 is in a forward bias, and IG≠0. If a reverse voltage is applied between the anode and the cathode, that is, UAK <0, because the emission junction J1 of T1 is reverse biased and T1 is in the off state, the unidirectional thyristor is in the blocking state, IA≈0; If a forward voltage is applied between the anode and the cathode, that is, UAK> 0, because the emission junctions J1, J3 of T1, T2 are forward biased, and the collector junction J2 is reverse biased, T1, T2 will be in an amplified state. After IG is amplified by T2, the collector current of T2 is IC2 = β2IG. The collector current of T2 is the base current of T1, after being amplified by T1, the collector current of T1 is IC1 = β1β2IG. This current flows into the base of T2 for amplification, and in this cycle, a strong positive feedback is formed, which makes T1, T2 quickly enter the saturation state, and the unidirectional thyristor is in the on state. After the unidirectional thyristor is turned on, UAK, the value of the voltage between the anode and the cathode is very small, and the external power supply voltage is almost completely dropped on the load.(3) Turn-off of the unidirectional thyristorFrom the above analysis, it can be seen that after the unidirectional thyristor is turned on, the base of T2 always has the collector current IC1 of T1 flowing, and the value of IC1 is much larger than the IG applied at the beginning. So even if the control electrode voltage disappears and IG = 0, it can still rely on the positive feedback of the tube itself to maintain conduction. Therefore, once the unidirectional thyristor is turned on, the control electrode will lose the function of controlling. After the unidirectional thyristor is turned on, if you want it to turn off again, the anode current IA must be reduced so that it cannot maintain positive feedback. To this end, the anode can be disconnected or a reverse voltage can be applied between the anode and the cathode.To sum up, under the condition that a forward voltage is applied between the anode and the cathode of the unidirectional thyristor, if a forward voltage is added between the control electrode and the cathode at a certain time, the unidirectional thyristor will change from the blocking state to the conducting state. This is triggered into conduction. After the unidirectional thyristor is turned on, the control electrode will lose the function of controlling. If you want to turn off the unidirectional thyristor again, you must make its anode current less than a certain value IH (called the holding current) or reduce the voltage UAK between anode and cathode to zero. b. TRIACA TRIAC is a three-terminal element with a five-layer structure of N1P1N2P2N3. It has three electrodes: a main electrode A1, a main electrode A2, and a control electrode (or gate) G. It is also a gate control switch. Regardless of its structure or characteristics, it can be regarded as a pair of anti-parallel ordinary thyristors. Its structure, equivalent circuit and symbols are shown in figure 3. Figure 3. Symbol, Structure and Equivalent Circuit of the TRIACThe main electrodes A2 and A1 of the triac are connected in series with the control object (load) RL, which is equivalent to a non-contact switch. The "on" or "off" of this switch is controlled by a signal uG (called a trigger signal) on the control electrode G. When there is a voltage (u ≠ 0) between the main electrodes A2 and A1, the moment the trigger signal uG appears, it will be conductive between A2 and A1 of the TRIAC, which is equivalent to the closed state of the switch. And once it is turned on, even if uG disappears, it can be kept on until u = 0 or the current in the series circuit of the main electrode and the load is reduced to a certain value, then it is turned off. After the cutoff, it is equivalent to the off state of the switch. In this way, the small current signal on the control electrode can be used to control the large current in the main electrode circuit. Figure 4. Volt-ampere Characteristic Curve of TRIACGenerally speaking, regardless of the voltage polarity between the two main electrodes A2 and A1 of TRIAC, as long as a certain amplitude of positive and negative pulses is applied to the control electrode, it can be turned on. So i represents the current in the main electrode and u represents the voltage between A2 and A1. The functional relationship between the two (called the volt-ampere characteristic curve) is shown in figure 4. It can be seen from the curve that the TRIAC has basically the same symmetrical performance in the first quadrant and the third quadrant.According to the voltage u on the main electrode and the polarity of the trigger pulse voltage uG on the control electrode, combined with the volt-ampere characteristic curve, the TRIAC can be divided into four trigger modes, which are defined as follows:(1) I+trigger: In the first quadrant of the characteristic curve (A2 is positive), the control electrode is a positive trigger relative to A1.(2) I-trigger: In the first quadrant of the characteristic curve (A2 is positive), the control electrode is a negative trigger relative to A1.(3) Ⅲ+trigger: In the third quadrant of the characteristic curve (A2 is negative), the control electrode is a positive trigger relative to A1.(4) Ⅲ-trigger: In the third quadrant of the characteristic curve (A2 is negative), the control electrode is a negative trigger relative to A1.Among these four trigger modes, I+ and III- have higher sensitivity, and are two commonly used trigger modes.In the control circuit of the new type electric heating electric appliance, the trigger signal applied to the control electrode of TRIAC is output by a single chip microcomputer or an integrated circuit. Some output a continuous positive (or negative) voltage signal, and some output a series of zero-crossing trigger pulses synchronized with a 50Hz sinusoidal AC power supply. The former is called a potential trigger, while the latter is called a pulse trigger. Their waveforms are shown in figure 5 and figure 6, respectively. Figure 5. Figure 6. Ⅱ The Main Characteristics of Thyristors2.1 Basic Structure of ThyristorA thyristor (also known as semiconductor controlled rectifier) is a high-power semiconductor device with a four-layer structure (PNPN). It has three lead-out electrodes, namely anode (A), cathode (K) and gate (G). Its symbolic representation and device cross-section are shown in figure 7. Figure 7. Symbol Representation and Device Cross-sectionOrdinary thyristors bidirectionally diffuse P-type impurities (aluminum or boron) in an N-type silicon wafer to form a P1N1P2 structure, and then diffuse N-type impurities (phosphorus or antimony) to form a cathode in most regions of P2, and at the same time lead out a gate electrode on P2 and form an ohmic contact is formed in the P1 as the anode.2.2 Volt-ampere Characteristics of ThyristorsThe on and off states of the thyristor are determined by the anode voltage, anode current and gate current. Volt-ampere characteristic curves are usually used to describe the relationship between them, as shown in figure 8. Figure 8. Volt-ampere Characteristic Curve of ThyristorWhen the thyristor VAK applies a forward voltage, J1 and J3 are forward biased, and J2 is reverse biased. The applied voltage almost falls on J2, and J2 plays a role of blocking the current. With the increase of VAK, as long as VAK <VBO, the passing anode current IA is small, so this region is called a forward blocking state. When VAK increases beyond VBO, the anode current suddenly increases, and it will be in a low voltage and high current state at the moment the characteristic curve passes the negative resistance. The on-state current IT determined by the load flows through the thyristor, the device voltage drop is about 1V, and the state corresponding to the CD section of the characteristic curve is called the on-state. VBO and its corresponding IBO are usually referred to as forward breakover voltage and breakover current. After the thyristor is turned on, it can maintain the on-state by itself. The transition from the on-state to the off-state is usually controlled by an external circuit without using a gate signal, that is, the device can be turned off only when the current is below a certain threshold value called the holding current IH.When the thyristor is in the off-state (VAK <VBO), if the gate electrode is made positive with respect to the cathode and the gate electrode is supplied with current IG, the thyristor will breakover at a lower voltage. The breakover voltage VBO and the breakover current IBO are both functions of IG. The larger the IG, the smaller the VBO. As shown in figure 3, once the thyristor is turned on, the device is turned on even if the gate signal is removed.When the anode of the thyristor is negative with respect to the cathode, as long as VAK <VBO, IA is small and has nothing to do with IG. However, when the reverse voltage is large (VAK≈VBO), the reverse leakage current through the thyristor increases sharply, showing thyristor breakdown. Therefore, VBO is called the reverse breakover voltage and breakover current.2.3 Static Characteristics of ThyristorsThe thyristor has 3 PN junctions, and the characteristic curve can be divided into (0 ~ 1) blocking area, (1 ~ 2) breakover area, (2 ~ 3) negative resistance area and (3 ~ 4) conducting area. a. Forward Working Area— Forward blocking (0 ~ 1) areaWhen a forward voltage is applied between AK, J1 and J3 bear the forward voltage, while J2 bears the reverse voltage, and the applied voltage falls almost entirely on J2. The reverse-biased J2 acts to block the current, and the thyristor is not conducting at this time.— Avalanche area (1 ~ 2 is also called breakover area)When the applied voltage rises close to the avalanche breakdown voltage VBJ2 of J2, the width of the space charge region of the reverse-biased J2 expands, and the internal electric field is greatly enhanced, which causes the multiplication effect to be strengthened. As a result, the current through J2 suddenly increases, and the current flowing through the device also increases. At this time, the current passing through J2 is transformed from the original reverse current to the current which is mainly attenuated by J1 and J3 through the base region and multiplied in the space charge region of J2. This is the avalanche area where the voltage increases and the current increases sharply. Therefore, the characteristic curve turns in the area, so it is called the breakover area.— Load area (2 ~ 3)When the applied voltage is greater than the breakover voltage, a large number of electron-hole pairs generated by the avalanche doubling of the space charge region of J2 are extracted by the reverse electric field. The electrons enter the region N1 and the holes enter the region P2. Due to the inability to recombine quickly, carrier accumulation occurs near both sides of J2: holes in region P2 and electrons in region N1, compensating for the charge of the ionized impurities and narrowing the space charge region. As a result, the potential in region P2 increases and the potential in the region N1 decreases, which acts to offset the external electric field. As the applied voltage at J2 decreases, the avalanche multiplication effect also weakens. On the other hand, the forward voltage of J1 and J3 has been enhanced, and the injection has increased, causing the current through J2 to increase, so a negative resistance phenomenon has occurred in which the current increases and the voltage decreases.— Low resistance on-state region (3 ~ 4)As mentioned above, the multiplication effect causes the accumulation of electrons and holes on both sides of J2, causing the reverse bias voltage of J2 to decrease; at the same time, the injection of J1 and J3 is enhanced, and the circuit is increased, so that charges continue to accumulate on both sides of J2, and the junction voltage continues to decrease. When the voltage drops to the point where the avalanche multiplication stops and all the junction voltages are cancelled, holes and electrons still accumulate on both sides of J2, and J2 becomes forward biased. At this time, J1, J2, and J3 are all forward biased, and large currents can pass through the device  because it is in a low-resistance on-state region. When fully conducting, its volt-ampere characteristic is similar to that of a rectifier element.b. Reverse Working Area (0 ~ 5)When the device is operating in reverse, J1 and J3 are reverse biased. Due to the very low breakdown voltage of the heavily doped J3, J1 withstands almost all of the applied voltage. The volt-ampere characteristic of the device is the volt-ampere characteristic curve of the reverse bias diode. Therefore, the PNPN thyristor has a reverse blocking region, and when the voltage increases above the J1 breakdown voltage, the current increases sharply due to the avalanche multiplication effect, at which time the thyristor is broken down. 2.4 Characteristic Equation of ThyristorA two-terminal device of a PNPN four-layer structure can be regarded as P1N1P2 and N1P2N2 transistors with current amplification coefficients of α1 and α2, respectively, where J2 is a common collector junction. When a forward voltage is applied to the device, the forward-biased J1 injects holes and passes through region N1 to reach the collector junction (J2). The hole current is α1IA; while the forward-biased J3 injects electrons and passes through region P2. The current carried to J2 is α2IK. Because J2 is in the reverse direction, the current through J2 also includes its own reverse saturation current, ICO.The current through J2 is the sum of the above three, that is,(1)Assuming the emission efficiency γ1 = γ2 = 1, according to the principle of current continuity IJ2 = IA = IK, so formula (1) becomes:(2)The formula shows that when the forward voltage is less than the avalanche breakdown voltage VB of J2, the multiplication effect is small and the injection current is also small. So α1 and α2 are also very small, thus(3)The ICO at this time was also small. Therefore, J1 and J3 are forward biased, so increasing VAK can only increase the reverse bias of J2. It cannot increase the ICO and IA a lot, so the device is always in the blocking state, and the current flowing through the device is the same order of magnitude as the ICO. Therefore, formula (3) is called a blocking condition.When the increase in VAK causes the reverse bias of J2 to increase and avalanche multiplication occurs, assuming multiplication factor Mn = Mp = M, then ICO, α1, and α2 will all increase by M times, so (2) becomes(4)At this time, the denominator becomes smaller, and IA will increase rapidly with the growth of VAK, so when(5)The avalanche steady-state limit is reached (VAK = VBO), and the current will tend to infinity, so equation (5) is called the forward breakover condition., , Using this feature, the breakover point conditions are derived from the characteristic curve equation (4). Because α1 and α2 are functions of current, M is a function of VJ2, which can be approximated with M(VJ2)=M(VAK), ICO is a constant and derive  with respect to (4). The outcome is(6)Since the breakover voltage is lower than the breakdown voltage,  must be a constant value. Because , the numerator must also be zero and obtain (7)According to the definition of transistor DC voltage amplification factor,                      (8)We can get the small signal current amplification factor                      (9)Using formula (9), formula (7) can be changed to                        (10)That is, at the breakover point, the product of the multiplication factor and the sum of the small signal is exactly 1. As long as the PNPN structure satisfies the above formula, it has switching characteristics, that is, it can be switched from an off-state to an on-state.Because α changes with the current IE, when IA increases, both α1 and α2 increase. It can be seen that, when the current is large, the value of M satisfying (6) can be reduced instead. This shows that IA increases and VAK decreases accordingly.α is both a function name of the current and a function of the collector junction voltage. When the current increases as α is constant, the corresponding reverse bias of the collector junction decreases. When the current is large,                             (11)According to equation (2), J2 provides an on-state current (ICO <0). Therefore, J2 must be forward biased, so J1, J2, and J3 are all forward biased, and the device is conducting. The off-state of the device changes to the on-state. The key is that J2 junction must be changed from reverse-biased to forward-biased. The condition for J2 to reverse to the forward direction is that holes and electrons should accumulate in regions P2 and N1, respectively. The condition for the accumulation of holes in region P2 is that the amount of holes α1IA injected by the J1 and collected by J2 into region P2 is greater than the amount of holes that disappear by recombination with (1-α2) IK, that is                           (12)Since IA=IK, α1+α2>1 is obtained. As long as the conditions are true, the hole accumulation in region P2 is the same, and the region electron accumulation condition is(13)Thus (14)It can be seen that when the condition of α1+α2>1 is satisfied, the potential of region P2 is positive, and the potential of region N1 is negative. J2 becomes forward-biased and the device is in a conducting state, so α1+α2>1 is called a conducting condition.Figure 9. SCR (Silicon Controlled Rectifier) Symbol Ⅲ The Main Parameters of Thyristor3.1 Main Parameters of Unidirectional ThyristorsIn order to correctly use a unidirectional thyristor, it is necessary not only to understand its working principle, but also to master its main parameters.(1) Forward repetitive peak voltage UFRMUnder the condition that the control electrode is disconnected and the unidirectional thyristor is in the forward blocking state, when the junction temperature of the unidirectional thyristor is the rated value, it is allowed 50 times per second, and the duration should not exceed 10 ms. The forward peak voltage that can be repeatedly applied to the unidirectional thyristor is called the forward repetitive peak voltage, which is expressed by UFRM. Generally, the secondary voltage is specified as 80% of the forward breakover voltage.(2) Reverse repetitive peak voltage URRMUnder the same conditions as the forward repetitive peak voltage, the reverse peak voltage that can be repeatedly applied to the unidirectional thyristor is called the reverse repetitive peak voltage, which is expressed by URRM and is generally 80% of the reverse breakover voltage.(3) Rated voltage UNUsually, the smaller one of UFRM and URRM is used as the rated voltage of the unidirectional thyristor. This is because the voltage added to the tube in practice is generally a positive and negative symmetrical voltage, so the voltage with a smaller value shall prevail. But because the transient over-voltage will also damage the tube, when selecting the tube, for safety reasons, the rated voltage of the tube is required to be greater than 2 to 3 times the actual peak voltage.(4) Rated forward average current IFThe average value of the power frequency sinusoidal half-wave current allowed to pass through the unidirectional thyristor under the ambient temperature of 40°C and specified heat dissipation conditions is called the rated forward average current IF. How many amp of the unidirectional thyristors we generally say refers to this current value. The amount of IF is related to factors such as the ambient temperature, heat dissipation conditions, and the conduction angle of the component. The rated current of the unidirectional thyristor is calibrated by the power frequency sinusoidal half-wave average current under certain conditions. This is because the load connected to the rectifier output often requires the average current to measure its performance. However, from the perspective of the unidirectional thyristor heating, regardless of the current waveform flowing through the unidirectional thyristor and the conduction angle of the unidirectional thyristor, as long as the effective value of the designed current is equal to the effective value of the rated current IF, then the heating of the unidirectional thyristor is equivalent and allowed.(5) Holding current IHAt room temperature, under the condition of the control electrode short circuit, the minimum anode current required to maintain the unidirectional thyristor to continue conducting is called the holding current IH. If the anode current of the unidirectional thyristor is less than this value, the unidirectional thyristor will change from the conducting state to the blocking state.(6) Control electrode trigger voltage UGK and trigger current IGAt room temperature, under the condition that the voltage between the anode and cathode of the unidirectional thyristor is 6V, the minimum DC current value of the control electrode required to change the unidirectional thyristor from the blocking state to the conducting state is called the trigger current IG. The DC voltage UGK between the control electrode and the cathode corresponding to the trigger current IG is called a trigger voltage. Generally, UGK is about 1 to 5V, and IG is tens to hundreds of mA.3.2 Main Parameters of TRIACIn various control circuits, the TRIAC is a relatively easy-to-damage component. Once the TRIAC is found to be damaged, you just need to replace the TRIAC with the same parameters. There are many characteristic parameters of TRIAC, and the following are the main parameters that should be considered during maintenance.— Off-state repetitive peak voltage-rated voltage VDRMWhen the control electrode is disconnected and the component is at the rated junction temperature, the voltage corresponding to the sharp bending point of the forward and reverse volt-ampere characteristics is called the off-state non-repeating peak voltage. 80% of it is called the off-state repetitive peak voltage. It is also called rated voltage, which is expressed by VDRM.When the TRIAC works, the peak value of the applied voltage momentarily exceeds the reverse non-repetitive peak voltage, which can cause permanent damage to the TRIAC. Moreover, due to the increase in ambient temperature or poor heat dissipation, the reverse non-repetitive peak voltage value may decrease. Therefore, when a TRIAC is selected, its rated voltage value should be 2 to 3 times the possible maximum voltage in actual operation. If the power supply voltage is 220V, a TRIAC with a rated voltage above 500V should be selected so that the selected components can withstand the surge voltage.— Rated on-state average current—rated current IT(AV)Under the specified conditions, the maximum average on-state current allowed when the TRIAC is on is called the rated on-state average current. According to the standard series of TRIAC, this current is taken to the corresponding current level, which is often referred to as the rated current for short and represented by IT(AV).Because the current overload capacity of the TRIAC is much smaller than that of ordinary motors and electrical appliances, the rated current of the TRIAC should be 1.5 to 2 times the maximum current in actual operation when selected.— Gate trigger current IGT (voltage UGT)This refers to the minimum trigger signal current (voltage) value that can make the TRIAC conduct reliably and add to the control electrode. If the trigger current (voltage) obtained by the TRIAC control electrode is less than the number of times, the TRIAC may not be turned on.— On-state average voltage UT(AV)Once the TRIAC is turned on, it is equivalent to the closed switch. Because the TRIAC is connected in series with the load, the smaller the voltage between the two main electrodes, the better. After the TRIAC is turned on, the average value of the voltage between the two main electrodes is called the on-state average voltage, which is usually referred to as the tube voltage drop. If the tube pressure drop of the TRIAC is too large, the motors and solenoid valves it controls may not work properly because they cannot get the full voltage.— Holding currentWhen the control electrode is disconnected at room temperature, the TRIAC is reduced from a large on-state current to a minimum main electrode current that is just necessary to maintain conduction, which is called a holding current. The TRIAC is turned off only when the main electrode current decreases below the holding current. Ⅳ Main Function of ThyristorThe functions of thyristors are as follows: first, converter rectification; second, voltage regulation; third, frequency conversion; fourth, switch (contactless switch). The most basic use of ordinary thyristors is controlled rectification. The diode rectifier circuit we are familiar with is an uncontrollable rectifier circuit. If the diode is replaced by a thyristor, it can constitute a controllable rectifier circuit, inverter, non-contact switch, achieve motor speed control, motor excitation, automatic control and so on. In electrical technology, the half cycle of alternating current is often defined as 180°, which is called the electrical angle. In this way, in each positive half cycle of U2, the electrical angle experienced from the beginning of the zero value to the moment when the trigger pulse arrives is called the control angle α; the electrical angle at which the thyristor conducts in each positive half cycle is called the conduction angle θ. Obviously, both α and θ are used to indicate the on or off range of the thyristor during the half cycle of the forward voltage. Controllable rectification is achieved by changing the control angle α or the conduction angle θ, and changing the average value UL of the pulsed DC voltage on the load. The function of a thyristor is not only rectification, it can also be used as a non-contact switch to quickly turn on or off the circuit, to achieve the inverter that converts DC power to AC power, to change AC power of one frequency to AC power of another frequency, etc. This article mainly introduces the basic principle, characteristics and main parameters of thyristors. Frequently Asked Questions about Thyristors (SCR)1. What are the characteristics of SCR?Characteristics of Thyristor or Characteristics of SCRReverse Blocking Mode of Thyristor. Initially for the reverse blocking mode of the thyristor, the cathode is made positive with respect to anode by supplying voltage E and the gate to cathode supply voltage Es is detached initially by keeping switch S open.Forward Blocking ModeForward Conduction Mode 2. Why SCR is called as thyristor?Silicon Controlled Rectifier (SCR) is a unidirectional semiconductor device made of silicon. This device is the solid state equivalent of thyratron and hence it is also referred to as thyristor or thyroid transistor. 3. Is SCR and thyristor are same?Thyristor is a 4 layer device formed by alternate combination of p and n type semiconductor materials. It is a device used for rectification and switching purpose. SCR is the mostly used member of thyristor family and it is the name commonly used when we talk about thyristors. 4. What is a thyristor used for?Thyristors are mainly used where high currents and voltages are involved, and are often used to control alternating currents, where the change of polarity of the current causes the device to switch off automatically, referred to as "zero cross" operation. 5. How does a SCR thyristor work?So how does it work? With no current flowing into the gate, the thyristor is switched off and no current flows between the anode and the cathode. When a current flows into the gate, it effectively flows into the base (input) of the lower (n-p-n) transistor, turning it on.
kynix On 2019-12-31   6341
Resistors

Selection, Replacement and Detection of Thyristor

IntroductionThyristor is a four semiconductor layers or three PN junctions devicea solid-state semiconductor device with four layers of alternating P- and N-type materials. It is also known as “SCR” (Silicon Control Rectifier). The term “Thyristor” is dervid from the words of thyratron (a gas fluid tube which work as SCR) and Transistor. And It acts exclusively as a bistable switch in electronic circuit.What is a Thyristor?CatalogIntroductionⅠ Types of ThyristorsⅡ Thyristor Selection2.1 Specific Requirements of Applying Circuit2.2 Main Parameters of the ThyristorⅢ Replacement of ThyristorⅣ Detection of Thyristor4.1 Detection of Unidirectional Thyristors4.2 Detection of TRIACⅠ Types of ThyristorsCommonly used thyristors include unidirectional thyristors, TRIAC, and turn-off thyristors, etc., which should be selected reasonably according to the needs of the circuit.— Unidirectional ThyristorThe unidirectional thyristor is characterized in that the current can only flow from the anode A to the cathode k, and is mainly used in the control of DC power supply or pulsating direct current, AC power rectification, and DC power inverter.Unidirectional thyristors can be divided into ordinary thyristors and high-frequency thyristors (the working frequency is above 110kHz). Commonly used unidirectional thyristors are 3CT series, 3DT series, KP series and KK series (high frequency thyristors), and imported MCR series, SF series, BST series etc.— TRIACTRIAC was developed on the basis of the unidirectional thyristor and is an AC power control device. TRIAC can not only replace two unidirectional thyristors in anti-parallel, but also requires only one trigger circuit, which is more convenient to use.The characteristic of TRIAC is that alternating current can pass through it, which is mainly used in the control of AC power supply and the adjustment of AC voltage. Commonly used TRIAC include 3CTS series and KS series, as well as imported MAC series, SM series, BCR series, etc.— Gate Turn-off ThyristorThe characteristic of the gate turn-off thyristor is that it can be switched off by the control electrode. It is mainly used in gate turn-off contactless switches, DC inverters, dimmer, speed regulation and other occasions.Gate turn-off thyristors are power-type control devices developed on the basis of ordinary thyristors. After the ordinary thyristor is triggered to be turned on, its control electrode does not work. To turn off the thyristor, the power must be cut off, or the forward current flowing through the thyristor must be less than the holding current. Gate turn-off thyristor overcomes the above drawbacks. When the control electrode G is added with a positive pulse voltage, the thyristor is turned on, and when the control electrode G is added with a negative pulse voltage, the thyristor is turned off.Gate turn-off thyristors are ideal high-voltage, high-current switching devices. For example, the DG series high-power gate turn-off thyristors can reach a maximum voltage of 4500V and a maximum current of 3000A. Ⅱ Thyristor Selection2.1 Specific Requirements of Applying CircuitThere are many types of thyristors, which should be selected reasonably according to the specific requirements of the application circuit.For AC/DC voltage control, controllable rectification, AC voltage regulation, power inverter, switching power supply protection circuit, etc., ordinary thyristors can be selected.For AC switch, AC voltage regulation, AC motor linear speed regulation, lamp linear dimming, solid state relay, solid state contactor, etc., a TRIAC should be selected.For AC motor variable frequency speed regulation, chopper, power inverter and various electronic switch circuits, you can choose gate turn-off thyristor.For sawtooth wave generator, long time delay, over voltage protector and trigger circuit with power transistor, etc., BTG thyristor can be selected.In electromagnetic cookers, electronic ballasts, ultrasonic circuits, superconducting magnetic energy storage systems, switching power supplies and other circuits, reverse conducting thyristors can be selected.In the photocoupler, light detector, light alarm, light counter, photoelectric logic circuit and operation monitoring circuit of automatic production line, the light-control thyristor can be selected.2.2 Main Parameters of the ThyristorThe main parameters of the thyristor should be determined according to the specific requirements of the application circuit.The selected thyristor should have a certain power margin, and its rated peak voltage and rated current (on-state average current) should be higher than the maximum operating voltage and maximum working current of the controlled circuit by 1.5 to 2 times.The parameters of the thyristor's forward voltage drop, gate trigger current, and trigger voltage should meet the requirements of the application circuit (this refers to the control circuit of the gate), and should not be high or low, otherwise it will affect the normal operation of the thyristor. Ⅲ Replacement of ThyristorAfter the thyristor is damaged, if no thyristor of the same type is replaced, another type of thyristor with similar performance parameters can be used instead.When designing an application circuit, a large margin is generally left. When replacing the thyristor, just pay attention to its rated peak voltage (repeated peak voltage), rated current (on-state average current), gate trigger voltage and gate trigger current, especially the two indicators of rated peak voltage and rated current.The switching speed of the thyristor used for replacement should be consistent with the switching speed of the damaged thyristor. For example: After the high-speed thyristor used in the pulse circuit and high-speed inverter circuit is damaged, only the same type of fast thyristor can be used instead of the ordinary thyristor.When selecting a thyristor to be used for replacement, it is not necessary to leave too much margin for any parameter, and the parameter of it should be as close as possible to the parameter of the replaced thyristor, because an excessively large margin is not only a waste, but also sometimes has side effects, such as non-triggering or insensitive triggering.In addition, the appearance of the two thyristors should be the same, otherwise it will cause inconvenience to the installation. Ⅳ Detection of ThyristorThyristors are usually represented by the letters "SCR" in circuit schematic diagrams. For example, SCR2 refers to the thyristor numbered 2. The symbol of the thyristor in the schematic diagram is shown in figure 1. Figure 1. Symbols of Thyristor4.1 Detection of Unidirectional Thyristors(1) Discrimination of each electrode: According to the structure of an ordinary thyristor, it can be seen that there is a PN junction between the gate G and the cathode K, which has unidirectional conductive characteristics, while there are two PN junctions of opposite polarities connected in series between the anode A and the gate. Therefore, by measuring the resistance between the pins of an ordinary thyristor with the R × 100 or R × 1 k Q level of the multimeter, three electrodes can be determined.The specific method is: use the black probe of the multimeter to connect one electrode of the thyristor, and use the red probe to touch the other two electrodes in turn. If the measurement result has a resistance value of several thousand ohms (kΩ) and another resistance value of several hundred ohms(Ω), it can be determined that the black probe is connected to gate G. In the measurement with a resistance value of several hundred ohms, the red probe was connected to the cathode K, and in the measurement with a resistance value of several thousand ohms, the red probe was connected to the anode A. If the measured resistance values are both very large, it means that the black probe is not connected to gate G. Apply the same method to test other electrodes until three electrodes are found.You can also measure the forward and reverse resistance between any two pins. If the forward and reverse resistance are close to infinity, the two electrodes are anode A and cathode K, and the other pin is gate G.Each electrode of the ordinary thyristors can also be judged according to its packaging form.For example, the bolt end of the bolt-type ordinary thyristor is anode A, the thinner lead end is gate G, and the thicker lead end is cathode K.The lead end of the flat thyristor is gate G, the flat end is anode A, and the other end is cathode K.A thyristor of metal package (T0-3) is a common thyristor and its shell is anode A.The middle pin of the plastic thyristor (T0-220) is anode A, and it is mostly connected with its own heat sink. Figure 2. Pin Arrangement of Several Common Thyristors(2) Judging whether it is good or bad: Use the R×1 kΩ level of a multimeter to measure the forward and reverse resistance values between anode A and cathode K of ordinary thyristor, which should normally be infinite (∞) ; If the forward and reverse resistance values are zero or the resistance values are both small, it indicates that a breakdown short circuit or leakage occurs inside the thyristor.Measure the forward and reverse resistance values between gate G and cathode K. Normally, there should be forward and reverse resistance values similar to diodes (the actual measurement results are smaller than those of ordinary diodes), that is, the forward resistance value is small (less than 2 kΩ) and the reverse resistance value is large (greater than 80 kΩ). If the resistance values of the two measurements are both large or small, it means that the thyristor is open or short-circuited between electrode G and K. If the forward and reverse resistance values are equal or close, it indicates that the thyristor has failed, and the PN junction between its electrodes G and K has lost its unidirectional conduction effect.Measure the forward and reverse resistance value between anode A and gate G. In normal conditions, both resistances should be several hundred kiloohms (kΩ) or infinite. If the forward and reverse resistance values are not the same (there is unidirectional conduction like a diode). One of the two PN junctions connected in reverse series between gate G and electrode A has been short-circuited.(3) Detection of triggering capability: For ordinary thyristors with low power (working current is below 5A), it can be measured with R×1 level of the multimeter . During the measurement, the black probe is connected to anode A and the red probe is connected to cathode K. At this time, the watch hand does not move, and the resistance value is displayed as infinite (∞). Use tweezers or wires to make anode A and gate G of the thyristor be short-circuited(see figure 3), which is equivalent to applying a forward trigger voltage to gate G. At this time, if the resistance value is several ohms to tens of ohms (the specific resistance value will vary according to the part number of the thyristor), it indicates that the thyristor is conducting due to the forward trigger. Then disconnect electrode A and gate G(the probes on electrode A and K do not move, only the trigger voltage of gate G is cut off). If the value indicated by the watch hand is still in the position of several ohms to tens of ohms, it indicates that the triggering performance of the thyristor is good. Figure 3. Detection of Triggering CapabilityFor medium and high power ordinary thyristors with a working current above 5 A, the on-state voltage drop VT, holding current IH and the gate trigger voltage Vo are relatively large. The current provided by the R × 1 kΩ level of the multimeter is low, and the thyristor cannot be completely turned on, so a 200Ω adjustable resistor and one to three 1.5 V dry batteries can be connected in series at the end of the black probe (depending on the capacity of the thyristor being tested, if its working current is greater than 100 A, three 1.5 V dry batteries are applied), as shown in figure 4. Figure 4. Detection of Trigger VoltageYou can also use the test circuit in figure 5 to test the triggering capability of an ordinary thyristor. In the circuit, vT is the thyristor under test, HL is a 6.3 V indicator (small electric beads in a flashlight), GB is a 6 V power supply (four 1.5 V dry batteries or 6 V regulated power supply can be used), and S is the button, R is the current limiting resistor. Figure 5. Test Circuit to Test the Triggering CapabilityWhen the button S is not connected, the thyristor VT is in a blocking state, and the indicator light HL is not on (if HL is on at this time, there may be breakdown of vT or leakage damage). After pressing the button S once (turn S on for a moment to provide the trigger voltage for gate G of the thyristor VT), if the indicator HL is always on, it means that the thyristor has a good triggering capability. If the brightness of the indicator is low, it indicates that the thyristor has poor performance and a large conduction voltage drop (the conduction voltage drop should be about 1 V under normal conditions). If button S is on, the indicator light is on, and when button S is off, the indicator light is off, indicating that the thyristor is damaged and the triggering performance is poor.4.2 Detection of TRIAC(1) Discrimination of each electrode: Use the R×1 or R×10 level of the multimeter  to measure the forward and reverse resistance values between three pins of the TRIAC. If it is measured that one pin is not connected with the other two pins, then this pin is the main electrode T2.After finding the electrode T2, the remaining two pins are the main electrode T1 and the gate G3. Measuring the forward and reverse resistance values between these two pins will gain two smaller resistance values. In a measurement with a small resistance value (about tens of ohms), the black probe is connected to the main electrode T1, and the red probe is connected to gate G.One end of the bolt of the bolt-shaped TRIAC is the main electrode T2, the thinner lead end is gate G, and the thicker lead end is the main electrode T1.    The shell of the metal-encapsulated (TO-3) TRIAC is the main electrode T2.The middle pin of the plastic-encapsulated (TO-220) TRIAC is the main electrode T2, which is usually connected to its own small heat sink. Figure 6. Pin Arrangement of Several TRIAC(2) Judging whether it is good or bad: Use the R×1 or R×10 level of a multimeter to measure the forward and reverse resistance values between the main electrode T1 and the main electrode T2 and between the main electrode T2 and gate G of the TRIAC. Normally it should be close to infinity. If the measured resistance values are all very small, it means that the electrodes of the TRIAC have been broken down or are short-circuited.Measure the forward and reverse resistance of the main electrode T1 and gate G. Normally, it should be between tens of ohms (Ω) and one hundred ohms (Ω) (when the black probe is connected to electrode T1 and the red probe is connected to gate G, the measured forward resistance value is slightly smaller than the reverse resistance value). If the forward and reverse resistance values between electrode T1 and gate G are measured to be infinite, it indicates that the thyristor has been damaged by an open circuit.(3) Detection of triggering capability: For small power TRIAC with working current below 8A, it can be measured directly with R×1 level of the multimeter. When measuring, first connect the black probe to the main electrode T2 and the red probe to the main electrode T1, then use tweezers to make electrode T2 and gate G be short-circuited, and add a positive polarity trigger signal to gate G. If the resistance value measured at this time changes from infinity to more than ten ohms (Ω), it means that the thyristor has been triggered to conduct, and the conduction direction is T2 → T1.Then connect the black probe to the main electrode T1, and the red probe to the main electrode T2. Use tweezers to make electrode T2 and gate G be short-circuited, and add a negative polarity trigger signal to gate G. If the resistance value measured at this time changes from infinity to more than ten ohms (Ω), it means that the thyristor has been triggered to conduct, and the conduction direction is T1 → T2.If gate G is disconnected after the thyristor is triggered to be turned on, the low-resistance conduction state cannot be maintained between electrode T2 and T1 and the resistance value becomes infinite, it indicates that the TRIAC has poor performance or is damaged. If a positive (or negative) polarity trigger signal is added to gate G, the thyristor still does not conduct (the forward and reverse resistance values between T1 and T2 are still infinite), then the thyristor is damaged and has no trigger continuity.For medium and high power TRIAC with a working current of 8A or more, when measuring their triggering capability, one to three 1.5V dry batteries can be connected in series to a probe of a multimeter, and then measure by using R×1 level as described above.For a TRIAC with a withstand voltage of 400V or more, its trigger capability and performance can also be tested by using 220V AC voltage.Figure 7 is a test circuit of a TRIAC. In the circuit, FL is a 60W /220V incandescent bulb, VT is the TRIAC under test, R is a 100Ω current limiting resistor, and S is a button. Figure 7. TRIAC CircuitAfter the power plug is connected to the working frequency AC, the TRIAC is in the off-state and the light bulb is off. (If the bulb is glowing normally at this time, it means that electrode T1 and T2 of the thyristor under test have been broken down and short-circuited; if the light bulb is slightly light, it means that the thyristor under test is damaged by leakage). Press the button S once to provide the trigger voltage signal for gate G of the thyristor. In normal conditions, the thyristor should be immediately triggered to turn on, and the light bulb will glow normally. If the bulb fails to emit light, the internal circuit of the tested thyristor is damaged. If the light bulb is turned on when the button S is pressed, and the light bulb is turned off when the button is released, it indicates that the triggering performance of the tested thyristor is poor.When using a multimeter to detect low-power light-controlled thyristors, put the multimeter in R × 1 level, connect one to three 1.5V dry batteries in series to a black probe, and measure the forward and reverse resistance values between the two pins. Normally it should be infinite. Then use a small flashlight or laser pen to illuminate the light receiving window of the light controlled thyristor. At this time, a small forward resistance value can be measured, but the reverse resistance value is still infinite. In a measurement with a small resistance value, the black probe is connected to the anode A, and the red probe is connected to the cathode K.The following method can also be used to measure light-controlled thyristors. Turn on the power switch S and illuminate the light receiving window of the thyristor VT with a flashlight. After adding a trigger light source (high-power light-controlled thyristor has its own light source, as long as the light-emitting diode or semiconductor laser in its optical cable is added with the working voltage, no external light source is required), the indicator EL should be on. After the light source is evacuated, the indicator light EL should remain illuminated. There is only one PN junction. Therefore, you just need to measure electrode A and G with a multimeter.Put the multimeter in the R × 1 kΩ level, and the two probes can be connected to one of the two pins of the thyristor under test (measure their forward and reverse resistance values). If a pair of pins is measured with a low resistance value, the black probe is connected to the anode A, while the red probe is connected to gate G, and the other pin is the cathode K. (2) Judging whether it is good or bad: Use the R×1 level of a multimeter to measure the forward and reverse resistance values between the electrodes of the BTG thyristor. Under normal conditions, the forward and reverse resistances between the anode A and the cathode K are infinite; the forward resistance between the anode A and gate G (when the black probe is connected to electrode A) is several hundred ohms to several thousand ohms and the reverse resistance value is infinite. If the forward and reverse resistance values between two electrodes are measured to be very small, it indicates that the thyristor has been short-circuited and damaged.(3) Detection of triggering capability: Put the multimeter in the R × 1 Ω level, connect the black probe to anode A, and the red probe to cathode K. The measured resistance should be infinite. Then touch gate G with your finger and add a human body induction signal to it. If the resistance between electrodes A and K changes from infinity to low resistance (a few ohms) at this time, it indicates that the thyristor has a good triggering ability. Otherwise, the performance of the thyristor is poor. Frequently Asked Questions about Thyristors1. What is thyristor and its types?A thyristor is a four-layer device with alternating P-type and N-type semiconductors (P-N-P-N). In its most basic form, a thyristor has three terminals: anode (positive terminal), cathode (negative terminal), and gate (control terminal). The gate controls the flow of current between the anode and cathode. 2. What is thyristor diagram?In general, Thyristors are also switching devices similar to the transistors. ... SCR or Thyristor is a four-layered, three-junction semiconductor switching device. It has three terminals anode, cathode, and gate. Thyristor is also a unidirectional device like a diode, which means it flows current only in one direction. 3. Where is thyristor used?Thyristors may be used in power-switching circuits, relay-replacement circuits, inverter circuits, oscillator circuits, level-detector circuits, chopper circuits, light-dimming circuits, low-cost timer circuits, logic circuits, speed-control circuits, phase-control circuits, etc. 4. Why SCR is called Thyristor?Silicon Controlled Rectifier (SCR) is a unidirectional semiconductor device made of silicon. This device is the solid state equivalent of thyratron and hence it is also referred to as thyristor or thyroid transistor. 5. What is thyristor diagram?In general, Thyristors are also switching devices similar to the transistors. ... SCR or Thyristor is a four-layered, three-junction semiconductor switching device. It has three terminals anode, cathode, and gate. Thyristor is also a unidirectional device like a diode, which means it flows current only in one direction.
kynix On 2019-12-31   5682
Resistors

Basic Knowledge of PCB

IntroductionA printed circuit board (PCB) mechanically supports and electrically connects electrical or electronic components using conductive tracks, pads and other features etched from one or more sheet layers of copper laminated onto and/or between sheet layers of a non-conductive substrate. A PCB allows signals and power to be routed between physical devices.What are PCBs? How Do PCBs Work?CatalogIntroductionⅠ PCB Basics1.1 PCB MaterialsⅡ PCB Product CharacteristicsⅢ Common Sense of PCB ProcessⅠ PCB Basics1.1 PCB Materialsa. Copper Clad Laminate(referred to as CCL, or sheet material)Tg: Glass Transition Temperature, which is the temperature at which glassy substances are transformed between glassy and highly elastic (usually softened). In the PCB industry, this glassy substance is generally referred to as resin or dielectric layer composed of resin and glass fiber cloth. Tg is an important technical index reflecting the heat resistance of printed circuit board substrates. Generally, the higher the Tg value of printed circuit boards, the better the heat resistance. The Tg of general FR-4 copper-clad epoxy glass laminates for SMT printed circuit boards is 130 ~ 140℃, which can meet the requirements when using Sn-Pn solder. For lead-free solders with higher melting points, the Tg of the substrate can not withstand the high temperature of welding if the Tg ≤ 150 ° C. In special cases (high temperature use), the Tg can be greater than 170 ° C. However, excessive Tg will cause the hardness of the substrate to increase and the material to become brittle. Therefore, we cannot simply pursue high Tg. We should comprehensively consider the performance of the board and choose a suitable printed board substrate with a higher Tg, which is one of the requirements for lead-free welding.CTI: Comparative Tracking lndex (or comparative leakage index, tracking index). The highest voltage value that the surface of the material can withstand 50 drops of electrolyte (0.1% ammonium chloride aqueous solution) without the formation of leakage traces. The unit is V.CTE: Coefficient of thermal expansion. Generally, the sheet material performance of a PCB is measured by the linear expansion coefficient, which is defined as the ratio of the increase in length to the original length under a unit temperature change, such as Z-CTE. The lower the CTE value, the better the dimensional stability and vice versa.TD: Thermal decomposition temperature refers to the temperature at which the base material resin loses weight by 5%. It is a sign of delamination and performance degradation caused by the heat of the base material of printed circuit boards.CAF: Conductive Anodic Filament of printed boards is the phenomenon of electrochemical insulation damage on insulating substrates. It refers to the state where dendritic metals are precipitated between wires under the action of an electric field after a voltage is applied to parallel circuits on printed circuit boards. Or conductive anodic filament(CAF) occurs along the glass fiber surface of the substrate, thereby reducing the insulation between the wires.T288: It is a technical index that reflects the welding resistance of the printed circuit board substrate. It refers to the maximum time that the printed circuit board substrate can withstand the high temperature of welding at 288°C without blistering and delamination. The longer this time, the better it is for welding. For traditional Sn-Pb alloys with low welding temperature (220 ~ 230℃), when the thermal decomposition time of printed circuit board substrate is 260 ℃, T260≥30s can meet the requirements of SMT printed circuit board. For lead-free welding, the temperature is generally 250 ~ 260℃, the thermal decomposition temperature of the substrate of the printed circuit board will increase, and only T288≥300s at 288 ℃ can ensure that the substrate does not decompose and the performance is not damaged during welding.DK: dielectric constant.DF: Dissipation factor refers to the ratio of the energy that has been lost in the insulation sheet material of the signal line to the energy that still exists in the line.OZ: oz is the abbreviation of the symbol ounce, which is British measurement unit and also unit of weight. 1 OZ means the thickness of copper with a weight of 1 OZ evenly spread over an area of 1 square foot (FT2). It is the average thickness of copper foil expressed by the weight per unit area. It is expressed by a formula, that is, 1OZ = 28.35g / FT2. b. Copper FoilED Copper Foil: Electrodeposited copper, copper foil commonly used in PCB, cheap.RA Copper Foil: Rolled annealed copper, copper foil commonly used in FPC.Drum Side: smooth side of electrodeposited copper foilMatt Side: rough side of electrodeposited copper foilCopper: Elemental symbol Cu, atomic weight 63.5, density 8.89 g / cm3, and the electrochemical equivalent of Cu2 + is 1.186 g / Ah. c. Prepreg: referred to as PPEpoxy Resin: an organic polymer compound containing two or more epoxy groups in the resin molecule, which is a resin component used in prepregs that are currently commonly used.DICY: Dicyandiamide, a common hardenerR.C: resin contentR.F: resin flowG.T: gel timeV.C: volatile contentHarden: Under certain conditions (high temperature, high pressure or light), the epoxy resin and the hardener undergo cross-linking polymerization to form a polymer with a three-dimensional mesh structure. d. InkViscosity: Viscosity refers to the relative movement between adjacent fluid layers when fluid is flowing, and frictional resistance will be generated between the two fluid layers. Unit: Pascal. Seconds (pa.s).Hardness: The hardness of the ink after pre-baking is 2B, the hardness of the ink after exposure is 2H, and the hardness of the ink after finishing is 6H. Thixotropic: a property that the ink is gelatinous when it is left to stand, but its viscosity changes when it is touched. It is a physical property of a liquid, that is, its viscosity decreases under agitation, and it will return to its original viscosity soon after standing. By stirring, the thixotropic effect lasts for a long time and it is enough to reconstitute its internal structure. To achieve high-quality screen printing, the thixotropic of the ink is very important. In particular, during the squeegee process, the ink is agitated to make it liquid. This action speeds up the speed of ink passing through the mesh, and promotes the original ink with separate wires to be evenly integrated. Once the squeegee stops moving, the ink returns to a stationary state, and its viscosity quickly returns to the original required data. e. Dry Film· Structure of dry film Figure 1. Structure of Dry Film· Dry film consists of three parts and ingredients:   — Supporting film(Polyester)   — Photo-resist dry film   — Covering film(Polyethylene)· Main ingredients① Binder(film-forming resin) ②Monomer ③Photo-initiator ④Plasticiser ⑤Adhesion promoter ⑥Thermal polymerization inhibitor ⑦Dye ⑧Solvent· The types of dry film are divided into three types according to the different methods of developing and removing the dry film: solvent-based dry film, water-soluble dry film, and peel-off dry film; according to the purpose of dry film, it is divided into: dry resist film, masking dry film and solder mask dry film.· Photosensitivity: It refers to the amount of light energy required for the photoresist to react to form a polymer with a certain resistance under the irradiation of ultraviolet light. In the case of constant light source intensity and light distance, the sensing speed is expressed as the length of exposure time. Short exposure time means that the sensing speed is fast.· Resolution: refers to the number of lines (or intervals) that can be formed by the dry film resist within a distance of 1mm. The resolution can also be expressed by the absolute size of the lines (or intervals). f. Net YarnNet density:— T number mesh number: refers to the number of meshes within 1 cm. g. Drill bit· geometry structure name of drill bitFigure 2. Geometry Structure Name of Drill Bit· Point AngleThe point angle is composed of two narrow and long first point angle surfaces and two triangular hook-shaped second point angle surfaces. These four sides meet at the point angle, forming two short edges called chisel edges at the center of the joint. This is the place that the sheet material first touches. This chisel edge is first positioned under pressure and rotation to drill into the stack. A protruding square strip on each of the two outer sides of the first point angle surface is called a margin. This margin tends to spiral upward along with the drill body part, which is the contact part between the drill pin and the hole wall. The right angle at the intersection of the margin and the edge lip is very important to the quality of the hole wall. The point angle has a long edge between the first and second point angle surfaces. The point where the two long edges and the two chisel edges meet in the middle is the point angle. The angle formed by the two long edges is called the point angle. When the drilling paper is made of phenolic resin substrate, the drill point angle is about 90° ~ 110° due to less resistance. When drilling paper is FR4 glass fiber board, the point angle should be slightly blunt at 115° ~ 135°. The most common one is 130°. The angle between the first point angle surface and the horizontal plane of the long edge is about 15°, which is called primary face angle. The second point angle is about 30°, and the angle formed by the chisel edge and the edge lip is called a cheisel edge angle. · Types of drill bitFigure 3. Types of Drill Bit Ⅱ PCB Product Characteristics1) Impedance· The sum of resistance and reactance (capacitance, inductive reactance) on a vector. Common impedance types are characteristic impedance and differential impedance.2) Warpage· Maximum bow (Figure a) and twist (Figure b) of printed circuit boards using surface mount components should be less than or equal to 0.75%3) RoHSRoHS, the abbreviation of restriction of hazardous substances, is the restriction of the use of certain hazardous substances in electrical and electronic equipment. RoHS lists a total of six harmful substances, including: lead(Pb), cadmium(Cd), mercury(Hg), hexavalent chromium( Cr6+), polybrominated diphenyl ether(PBDE), polybrominated biphenyl(PBB).4) BacklightIt is an enlarged visual inspection method to check the integrity of the copper wall of the through hole. The method is to carefully thin the substrate outside the hole wall from a certain direction, and then use the principle of resin translucency to shoot light from the back. If the quality of the chemical copper hole wall is intact and there is no any holes or pinholes, the copper layer must be able to block light and be dark in the microscope. Once there are holes in the copper wall, light spots must appear and be observed , and can be enlarged as photographic evidence. The ground sample is about 4-6mm wide.Figure 5. Backlight Standard Diageam5) Anode Phosphor Copper Ball· Purity requirementsElementContent(%)ElementContent(%)Cu≥99.91Ni≤0.002P0.040-0.06Sb≤0.002Pb≤0.002As≤0.002Fe≤0.0025S≤0.002Sn≤0.002O≤0.002 · Features— A black (or brown-black) film forms on the surface of phosphor copper after power is applied.— Black (or brown-black) film is Cu3P, also called phosphor copper anode film.· Role of phosphor copper anode film— The anode film itself can catalyze and accelerate the (Cu+-E → Cu2+) reaction, thereby reducing the accumulation of CU+.— After the anode film is formed, it can inhibit the continuous generation of Cu+.— The electrical conductivity of the anode film is 1.5X104-1 cm-1, which has metal conductivity.— Phosphor copper is less anodized than pure copper (1A / DM2 P0.04-0.065%, phosphor copper is less anodized than oxygen-free copper, 50MV-80MV) and will not cause anode passivation.— Anode film will greatly reduce the phenomenon of tiny grains falling off the anode.— Anode film prevents the copper anode from dissolving too quickly.6) Method for Estimating Surface Area of Electroplated Copper Anode· Method for estimating surface area of round titanium basket copper anode: pDLF/2p = 3.14 D = diameter of titanium basket L = length of titanium basket F = factor· Method for estimating surface area of square titanium basket copper anode: 1.33LWFL = length of titanium basket W = width of titanium basket F = factor· F is related to the diameter of the copper ball:Diameter = 12 mm    F = 2.2Diameter = 15 mm    F = 2.0 Diameter = 25 mm    F = 1.7Diameter = 28 mm    F = 1.6 Diameter = 38 mm    F = 1.27) ICD IssuesInternal Connection Defects Ⅲ Common Sense of PCB Processa. Etching FactorThe index used to consider the amount of etching lateral erosion, because the amount of lateral erosion will be different for different copper thickness, so the etching factor is different from the total copper thickness.Calculation method:b. Lateral ErosionThe etching of the side wall of the wire under the resist pattern is called lateral erosion, and the degree of lateral erosion is expressed by the width of the side etching:· lateral erosion is related to the type, composition and etching process and equipment of the etching solution. c. Pool EffectDuring the etching process, the circuit board passes through the etching machine horizontally. Due to the gravity acting on it, the fresh medicine is blocked by the old one and cannot effectively react with the copper surface. d. Different Stages of ResinsA-stage resin: Some thermosetting resins are liquid in the early stages of manufacture or liquid when heated, and can still dissolve in some liquids at this time.B-stage resin: Some thermosetting resins can soften when heated in the middle stage of the reaction, but they cannot be completely dissolved or melted. At this time, they can swell or partially dissolve when contacted with some solvents.C-stage resin: The later stage of the reaction of some thermosetting resins, when it is practically insoluble or infusible. e. Font Color of SubstrateRed font: flame retardant grade, other fonts: non flame retardant grade. f. OthersMSDS: Material Safety Data Sheet provides a variety of information on safety, health and environmental protection for chemical substances and products, and can provide information on basic knowledge, protective measures and emergency actions of chemicals. In some countries, MSDS is also called SDS, and SDS terminology is used in ISO 11014.SGS: Societe Generale de Surveillance S.A. Founded in 1887, it is currently the world's largest and oldest non-governmental third party engaged in product quality control and technical certification of multinational companies. Headquartered in Geneva, it has 251 branches around the world, 256 professional laboratories and 27,000 professional and technical personnel, and carries out product quality inspection, monitoring and assurance activities in 142 countries.UL: UNDER WRITERS LABORATORIES INCIPC: The Institute for International and Packaging Electronic CircuitsISO: International Standards OrganizationMIL: Military StandardJPC: Japan Printed Circuit AssociationCOV: Coefficient of variationFR4: Abbreviation for Flame Retardant Type 4. It is the name of a flame-resistant printed circuit board material composed of a composite material of glass fiber and epoxy resin. It is the most widely used printed circuit board. g. pH ValueAlso known as the hydrogen ion concentration index and pH value, it is a scale of the hydrogen ion activity in a solution, which is a measure of the acidity and alkalinity of a solution in the usual sense. The concept was proposed by Danish biochemist Søren Peter Lauritz Sørensen in 1909. P stands for German Potenz, which means strength or concentration, and H stands for hydrogen ion (H +). Sometimes pH is also written in Latin as pondus hydrogenii.Under normal conditions (25°C, about 298K), when pH <7, the solution is acidic, when pH> 7, the solution is alkaline, and when pH = 7, the solution is neutral. h. Hull Cell TestHull designed Hull cell in 1939. The Hull cell test only requires a small amount of plating solution. After a short time test, the plating effect of the plating solution can be obtained in a wide range of current density. Because this test is sensitive to the composition and operating conditions of the plating solution, it is commonly used to determine the concentration and pH value of each component of the plating solution, and to determine the current density range for obtaining a good coating. The Hull cell has become an indispensable tool for electroplating research and electroplating process control.Hull cells are usually made of insulating materials such as plexiglass or rigid polyvinyl chloride. The bottom surface is trapezoidal, and the cathode and anode are placed on two sides that are not parallel. There are five types of capacity: 250ml, 267ml, 320ml, 534ml, and 1000ml. Generally, 250ml plating solution is often added to a 267ml test cell, which is convenient for converting the additives into how many grams per liter.Figure 8. Dimensions of Hull Celli. Current Density A / dm2A/dm2 — how many amperes per square decimeter area, 1A / dm2 — This is the current density of electroplating, which means that the current passes through the plating area of the workpiece per square decimeter is 1A and dm means decimeter. Generally, we use a 267ml Hull cell, place the test piece at the cathode and immerse it in the test solution. The area of the test piece is approximately 1dm2. j. TP: THROUGH POWERCalculation method:k. Replacement ReactionA replacement reaction is a chemical reaction in which a simple substance reacts with a compound to form another simple substance and a compound. Any replacement reaction is a metathesis reaction, including a reaction of metal and metal salt, the reaction of metal and acid, etc.; the replacement reaction must be a redox reaction, and the redox reaction is not necessarily a replacement reaction; the replacement reaction occurs according to the active list of metals. l. EDS:Energy Dispersive X-ray SpectroscopyThe surface of the sample being tested is irradiated with a condensed electron beam. Due to the interaction between the electron beam and the sample, various electrons or X-rays, photons, and other information are generated. Then, this information is collected and processed in different ways to display various characteristics of the sample (morphology, microstructure, composition, crystal plane, etc.) m. SEM:Scanning Electron MicroscopeAn electron beam with a diameter of 20 mm to 30 mm emitted from the cathode of the electron gun is accelerated by the voltage between the cathode and the anode, and is directed toward the lens barrel, and is condensed by the condenser lens and the objective lens, and is reduced into an electron probe with a diameter of about several nanometers. Under the action of the scanning coil on the upper part of the objective lens, the electron probe scans the surface of the sample in a raster pattern and excites a variety of electronic signals. These electronic signals are detected by corresponding detectors, amplified, converted into voltage signals, and finally sent to the grid of the picture tube and modulate the brightness of the picture tube. The electron beam in the picture tube is also raster scanned on the phosphor screen, and this scanning movement is strictly synchronized with the scanning movement of the electron beam on the sample surface, so that a scanning electron image corresponding to the contrast and the intensity of the received signal is obtained. The image reflects the topographical features of the sample surface. n. BONDINGBonding is a wiring method in the chip production process. It is generally used to connect the chip's internal circuit with gold or aluminum wires to the package pins or gold-plated copper foil on the circuit board before packaging. Ultrasonic waves from an ultrasonic generator (generally 40-140KHz), which generates high-frequency vibration through the transducer, are transmitted to the splitter through the horn. When the splitter is in contact with the lead wire and the welded part, under the action of pressure and vibration, the surfaces of the metal to be welded rub against each other, the oxide film is destroyed, and plastic deformation occurs, causing the two pure metal surfaces to closely contact each other to achieve the combination of atomic distance, and finally form a strong mechanical connection. After bonding (ie, after the circuit is connected to the pins), the chip is packaged with black glue. o. The Giovanni EffectIt means that due to the potential difference between two metals, an electric current is generated through the medium, and then an electrochemical reaction occurs, and the anode with a high potential is oxidized. p. Vacuum Degree; Degree of VacuumThe degree of thinness of the gas under vacuum is usually expressed by "high vacuum" and "low vacuum", high vacuum indicates "good" vacuum, and low vacuum indicates "poor" vacuum. If the pressure in the device under test is lower than atmospheric pressure, a vacuum gauge is required for pressure measurement. The value read from the vacuum gauge is called the degree of vacuum. The degree of vacuum is a value indicating that the actual value of the system pressure is lower than the atmospheric pressure, that is: the degree of vacuum = atmospheric pressure-absolute pressureThere are usually two ways to identify the degree of vacuum:   — First, it is marked with "absolute pressure" and "absolute vacuum degree" (that is, how much pressure is higher than "theoretical vacuum"); in actual cases, the absolute pressure value of the vacuum pump is between 0 and 101.325KPa. The absolute pressure value needs to be measured with an absolute pressure meter. The initial value of the gauge (absolute vacuum gauge) for measuring the vacuum degree at 20°C and the place where the altitude = 0 is 101.325KPa (ie, a standard atmospheric pressure).   — The second is to use "relative pressure" and "relative vacuum degree" (that is, how much pressure is lower than "atmospheric pressure") to identify. "Relative vacuum degree" refers to the difference between the pressure of the measured object and the atmospheric pressure at the measurement site and is measured with an ordinary vacuum gauge. In the absence of vacuum (that is, at atmospheric pressure), the initial value of the gauge is 0. When measuring vacuum, its value is between 0 and -101.325KPa (usually expressed as a negative number).Commonly used vacuum units are Pa, Kpa, Mpa, atmospheric pressure, kilogram (Kgf / cm2), mmHg, mbar, bar, PSI, etc. The approximate conversion relationship is as follows:   — 1MPa = 1000KPa   — 1KPa = 1000Pa   — 1 atmospheric pressure = 100KPa = 0.1MPa   — 1 atmospheric pressure = 1 kg (Kgf / cm2) = 760mmHg   — 1 atmospheric pressure = 14.5 PSI   — 1KPa = 10mbar   — 1bar = 1000mbar Frequently Asked Questions about PCB Basic1. What is PCB and types of PCB?A printed circuit board (PCB) is a thin board made from fiberglass, composite epoxy, or other laminate materials. PCBs are found in various electrical and electronic components such as beepers, radios, radars, computer systems, etc. Different types of PCBs are used based on the applications. 2. What is the basis of PCB?PCB is the acronym of Printed Circuit Board, a mechanical base that contains tracks and footprints reflecting the schematic of the design. Modern PCBs are typically made of a non-conductive substrate that is overlayed by copper layers. 3. What are the basic steps of PCB design?Here's the full list of PCB layout and design steps:Create the Schematic.Create a Blank PCB Layout.Schematic Capture: Linking to Your PCB.Designing Your PCB Stackup.Defining Design Rules and DFM Requirements.Place Components.Insert Drill Holes.Route Traces. 4. What are the common types of PCB?Common Types of Printed Circuit BoardsSingle Layer PCB. Single layer printed circuit boards are among some of the simplest to design and manufacture. ...Double Layer PCB.Multi-Layer PCB.High Density Interconnect (HDI) PCB.High Frequency PCB. 5. Which material is used in PCB?copper circuitryPrinted circuit boards (PCBs) are usually a flat laminated composite made from non-conductive substrate materials with layers of copper circuitry buried internally or on the external surfaces. They can be as simple as one or two layers of copper, or in high density applications they can have fifty layers or more.
kynix On 2019-12-30   3799

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.