ics Related Articles
Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips
- Electronic Components
- News Room
- General electronic semiconductor
- Components Guide
- Sort by
- Robots
- Transmitters
- Capacitors
- IC Chips
- PCBs
- Connectors
- Amplifiers
- Memory
- LED
- Diodes
- Transistors
- Battery
- Oscillators
- Resistors
- Transceiver
- RFID
- FPGA
- Mosfets
- Sensor
- Motors, Solenoids, Driver Boards/Modules
- Relays
- Optoelectronics
- Power
- Transformer
- Fuse
- Thyristor
- potentiometer
- Development Boards
- RF/IF
- Semiconductor Information
- Sensors
- PCB
- transistor
Ⅰ IntroductionAn operational amplifier, or op-amp for short, is fundamentally a voltage amplifying device designed to be used with external feedback components such as resistors and capacitors between its output and input terminals. Learn more about the most common opamp basics, essential knowledge when selecting and using an op amp in electronics. We can conclude our section and look at Op Amp basics with the following properties and questions. Opamp Basics: Op-Amp CircuitsCatalogⅠ IntroductionⅡ Amplifier Figures of MeritⅢ Q & AⅣ Application: LM358 Classic CircuitsⅡ Amplifier Figures of MeritNegative FeedbackIt is a important technique to improve bandwidth and distortion and control gain.Open-loop GainIt refers to the ratio of the voltage change at the output of the amplifier to the voltage change at the input when the amplifier input and output are open. Common-mode Rejection Ratio (dB)It is the ratio of the amplifier's amplification factor of the differential voltage signal to the amplification factor of the common mode voltage signal.Input Current NoiseIt is the equivalent current noise applied in parallel with the input of the noiseless amplifier.Output CurrentIt refers to the current driven by the load at the output of the op amp. It is usually a function: input overdrive, correlation between output voltage and power supply, temperature, source, and drain characteristics will differ.Phase MarginIt is the phase shift between an output of the same frequency and an inverting input in an open-loop circuit.Voltage GainIt is the ratio of the change in output voltage to the change in input voltage.Programmable Gain BufferIt can set the gain resistance of the op amp (integrated on the template), and the gain can be set to +1, +2, or -1 through simple external connections.Saturation VoltageIt is the voltage between the collector and emitter of the transistor under saturation conditions. In the saturated state, the emitter-base and collector-base are forward biased, so that the voltage between the collector-emitter is very low.Rise TimeThis refers to the time required for the output voltage to change from 10% of its final value to 90% of its final value.Unity-gain BandwidthIt refers to the frequency at which the amplifier's open-loop gain is equal to one. If the op amp frequency response has a single-pole roll-off, the unity-gain bandwidth is equal to 1UGBW.Strobe “OFF” VoltageThe strobe “OFF” voltage is the minimum voltage at the strobe pulse and is guaranteed not to interfere with the comparator operation.Input Current IndexIt refers to the average of the current drawn from the two input pins. In addition, the input current is also commonly called bias current.Gain Bandwidth ProductIt refers to the product of the amplifier's bandwidth and the gain at which the bandwidth is measured.Large Signal Voltage GainIt refers to the ratio of the change in output voltage to the change in input voltage. This parameter is usually specified at a large output voltage, smaller than the maximum output voltage, which is the typical value under direct current conditions.Offset Voltage Temperature CoefficientIt refers to the average rate of change in offset voltage due to changes in junction temperature within a specified temperature range.Output High VoltageIt refers to the high DC output voltage of the comparator, which produces the high output current. And it is usually related to the totem pole or push-pull output of the comparator.Input Source CurrentIt refers to the maximum output positive current produced under the comparator's push-pull output state.Total Harmonic Distortion (THD)When a pure sinusoidal signal is input to the op amp as Vin (w) = Vpsin (wt):Input harmonic distortion: Vout(w)a1Vpsin(wt)+a2Vpsin(wt)+...+anVpsin(nwt)The expression of THD is: THD(%)=[sqrt(a2xa2+a3xa3+...+anxan)/a1]x100Common-Mode Input Impedance (RINCM)It refers to the ratio of the change in the common-mode input voltage to the change in the input current at the inverting or non-inverting terminal.Output Low VoltageIt refers to a low DC output voltage. The output drive is a low voltage sink current. This specification is usually related to the totem pole or push-pull output of the comparator.Using a CMOS op amp as the output driver, although the circuit works well, but requiring a 1m shielded cable, and the oscillation of the operational amplifier is about 1MHz when there is no input signal. If shorten the cable to 10cm, the oscillation is stable.Some op amps are not suitable for driving capacitive loads directly, such as long shielded cables, which is a capacitive load. In addition, coaxial cables have about 60-100pF capacitance per meter.Harmonic DistortionIt refers to the unwanted spurious signals generated at the amplifier output due to the non-linearity of the signal line. When the input is a sinusoidal signal, these spurious signals will appear as integer times of the input frequency (for example, second harmonic, third harmonic).Output Leakage Current (ILEAKAGE)It means that the current enters the comparator output (the output is driven high). It often appears at the output of open collector and open drain.Power Supply Rejection Ratio (PSRR)It refers to the ratio of the change in the input offset voltage to the change in the power supply voltage, PSRR (dB) = 20log10 (DVOS / DVS)Linear Phase DeviationIt refers to how a closed-loop phase response of an operational amplifier approaches and follows the linear relationship between phase change and frequency in a specific frequency band.-3dbIt refers to the frequency when the value of the small signal output amplitude of the closed-loop amplifier decreases to 3dB.Common-mode Voltage RangeIt refers to the typical value of the voltage range at the input, which determines the performance of the amplifier.Specified Power Supply RangeIt describes the power supply voltage required for the operational amplifier to operate.Output Absorption CurrentIt refers to the highest output negative current of the comparator.Output Voltage SwingIt refers to the maximum peak-to-peak swing of the output voltage under a specific load and power supply voltage.Current FeedbackIt refers to a technology used in current feedback amplifiers whose output signal reflects the value of the current input to the inverting input (transimpedance gain function). In some aspects, this topology has operational advantages over traditional voltage feedback.Closed Loop BufferIt refers to an amplifier with high input impedance and low output impedance and a fixed gain of +1. Its typical applications are used for isolation, increased output drive, capacitive load, etc., in addition, there is no need to set the gain resistance.Closed-loop Gain It is the ratio of the change in the output voltage to the change in the input voltage after the feedback and input network added. Generally, this value is set using an external resistance.Common-mode RangeThe common-mode range, also known as the input voltage range, is a measure of the range of input voltages that the input pins of an op amp can accept. This specification is usually relative to the power supply amplitude.Output ImpedanceIt refers to the ideal series output impedance of the ideal operational amplifier when there is no impedance, which is the approximate output impedance of the op amp measured under AC conditions.Transient ResponseIt refers to the step function response of the closed-loop system of the amplifier under the condition of small signal (usually less than 100mV).Slew RateWhen given a transition or square wave input, the amount of change in the amplifier's output from one level to another. Typical values are averages of values measured based on a change in total output voltage from 10% to 90%.Response TimeIt is the time interval when the input step function makes the output from the initial value to the logic threshold voltage.Unity Gain FrequencyIt refers to the frequency at which the gain of the voltage feedback op amp is 1 (0 dB). For an ideal operational amplifier, its gain-bandwidth product is equal.Intercept PointIt refers to the output power of the fundamental frequency, which is equal to the power value of the fundamental frequency in the specified distortion term (2nd, 3rd, or 3rd intermodulation).Input Offset CurrentIt refers to the current difference between the two inputs.Voltage OverdriveIt means that a certain amount of input step voltage exceeds the minimum drive input voltage required by the comparator to change from one logic level to the opposite logic level.Differential Gain & Differential PhaseDifferential gain refers to the change in the input and output of the gain, and differential phase refers to the phase change in the input stage. They are video measurements, and are a standard measurement in the broadcasting field to measure relative changes in the interpretation of video signal consistency.Voltage FeedbackA technique used in traditional operational amplifiers, where part of the output voltage is fed back to the input, and the voltage difference between the two inputs is amplified by the operational amplifier. Avol Open-loop Voltage Gain“A” is a sign of gain. The letter “V” written below indicates the gain of voltage, and the letter “ol” also written below is an abbreviation for open loop. Open-loop voltage gain refers to the gain (Vout / Vin) of the amplifier without feedback. Due to the existence of the bias voltage, these errors must be compensated.Logic Threshold VoltageIt refers to the voltage that causes the comparator output state to change when the input offset voltage is exceeded.Output ResistanceIt refers to the value of the series resistance at the output of an ideal op amp with zero output resistance, which measured under DC conditions.Gain FlatnessIt refers to the volume of gains “violently increasing” and “rapidly decreasing” in a given bandwidth range measured in decibels (dB), which affects the most important parameter specifications such as phase margin, gain margin, and closed-loop gain.Offset Current Temperature CoefficientIt refers to the average rate of change in deviation current due to changes in junction temperature within a specified temperature range.Input ImpedanceIt is the ratio of input AC voltage to input AC current.Input Voltage NoiseIt refers to the equivalent voltage noise in series with a noiseless amplifier.Input Offset VoltageIt is the product of the DC error voltage between the inputs and the closed-loop gain, because of the non-ideal balance between the input stage and the output is caused by the DC error voltage of the input terminals.Gain MarginOpen loop gain when the phase between the inverting input and output crosses zero at a certain frequency.Supply CurrentIt refers to the current required from the power supply to the unloaded amplifier and to the power supply at the output midpoint.Settling TimeIt refers to the time between the input step function initial value and the output voltage reaching the specified error band. The error band refers to the percentage of the total voltage change.Differential Input ResistanceIt is the ratio of the change in the input voltage to the change in the input current.Ⅲ Q & AQ1: What is the difference between a voltage feedback amplifier and a current feedback amplifier?A: The internal circuits of these two op amps are different. The voltage feedback op amp is restricted by the internal design, and it only has a very low input bias current, but there is no internal limit on the differential input voltage, because it is limited only when external feedback is required. In contrast, for a current feedback amplifier, its differential input voltage is subject to internal design, but it does not limit its input bias current, so it is limited only when external feedback is required.Q2: What is the difference between open and closed loops?A: The open loop gain is actually the internal gain of the op amp without feedback, and usually takes any value between 1,000 and 10,000. Closed loop gain is the gain of the entire circuit, which is equal to the open loop gain divided by 1 plus the loop gain (the improvement coefficient). In fact, the gain of the op amp when there is no feedback is the open loop gain, and the gain when feedback is considered is closed-loop gain.Q3: If the op amp has ideal AC characteristics, the Bode plot (gain-frequency response) is a unipolar system. What is the gain slip rate in dB / decade?A: In a unipolar system, the gain drops (or decreases) at 20dB / decade, which is 6dB / octave. This is responsive to any single pole, and it is also suitable for a simple RC filter or an ideal operational amplifier. However, because op amps have more high-frequency poles, the phase shift will begin to increase as the frequency approaches the unity gain frequency of the op amp.Q4: What is the difference between unity gain bandwidth, gain bandwidth product (GBP), and -3dB frequency?A: Many op amps have an open-loop gain reduction rate of -20db / decade when the frequency is stable. At any point during this descent phase, the GBW is a constant. If the unity-gain operation of the op amp is stable, then the unity-gain bandwidth, or the frequency at which the open-loop gain is 1, is usually equal to GBP. In addition, GBP is not equal to (usually higher than) the unity gain bandwidth. The -3dB frequency is a measure of the bandwidth of an operational amplifier when it is operating in a closed loop. The -3dB point is the frequency at which the gain of the overall closed-loop system drops by 3dB. The unity gain frequency for closed loop applications can be calculated using BW=GBP/Av. The -3dB frequency and unity-gain bandwidth applied depend on the feedback gain setting, output swing, load, and circuit layout.Q5: Why do some amplifiers oscillate with a capacitive load?A: The output impedance of the op amp and the capacitance of the capacitive load may form a resistance-capacitance oscillation. Also they form an R-C oscillation at the output stage, which causes additional phase lag in the feedback signal. CMOS amplifiers have a high output impedance which will cause the electrodes to be approached or lower the unity gain frequency of the op amp. The additional phase lag of the electrodes will weaken the phase margin of the op amp The total phase lag of the amplifier causes the phase angle of the unity gain frequency to increase by more than 180 degrees to cause the total feedback phase shift in unity gain to exceed 180. degree. In addition, the output impedance of a CMOS amplifier is between 100 and 500, causing a relatively low pole frequency. And meanwhile, the output impedance of the high-speed bipolar operational amplifier is in the range of 1 to 100, which causes the pole frequency to be much higher than that of the CMOS operational amplifier, so that the pole is far from the unity gain frequency of the device. The drive of a CMOS amplifier to a capacitive load can be improved by placing an output resistor at the output and an external positive feedback capacitor.Q6: If the output of the op amp stays close to the voltage rail, that is, the output rail, what is the reason?A: There are many ways for operational amplifiers to “rail”. The difficulty is keeping it away from the "rail". If the input exceeds the input voltage range, the output is usually near to a supply voltage rail. In theory, if the output exceeds the actual supply voltage, and a higher supply voltage is given, the op amp will go to rail output again. If there is no feedback or the polarity of the feedback is wrong, the op amp goes to rail output again. At the same time, if the non-inverting input is higher than the negative inverting input, the op amp also goes to rail output. The application of the operational amplifier should be analyzed to ensure that the power supply voltage used has a proper input and gain, so that in normal operation, its input voltage is within the rated value and the output voltage is within the normal range.Q7: What is the difference between the common-mode voltage and input voltage range of an op amp?A: Common mode voltage means that one voltage is applied to both inputs at the same time. Input voltage range is the range of voltages that can be accepted by the input pins. It is necessary to remember that the op amp should suppress the common-mode voltage, and amplify the difference between the two input pins only.Q8: The SPICE model of the bipolar operational amplifier works well, but the SPICE model of the CMOS operational amplifier does not work. Is there a need to set SPICE?A: To input the appropriate bias current to the model, the SPICE model applied on CMOS operational amplifier needs to set the default GMIN option to the largest SPICE package value.Q9: What is the difference between the amplifier's output current and short-circuit current?A: Short circuit current refers to the current generated by the device if the output is connected directly to the power line. This indicates that the output current is limited depending on the design of the device. However, the short-circuit current does not represent the true output of the drive capability of the output. Due to the impedance characteristics of the output stage, the maximum output current is determined by the swing of the output voltage under load. In facet, the smaller the load, the larger the output swing; the larger the load, the smaller the output swing.Q10: How to check the stability of an op amp circuit?A: Check the stability of the control loop, such as the pulse load and related changes in output voltage. The pulse load may be a load current with a pulse or step change, so that the output of the op amp circuit should be connected to a series R-C circuit. The greater the circuit swing or vibration, the worse the stability of the circuit.Q11: Are there any good ways to minimize noise when amplifying a low-level DC signal?A: To obtain a high signal-to-noise ratio, the circuit must be well designed. This includes choosing the best amplifier bandwidth and knowing the impedance of the input signal. If the input signal source has a fairly high impedance, it makes no sense to choose a low voltage noise amplifier, which has high current noise.Q12: How should design a low frequency (<1Hz) differentiator to minimize the output noise?A: The only reason that the output of the differentiator contains noise is because there is a lot of gain and the input is noisy. The traditional differentiator uses Rs-Cs in series at the input and the Rf-Cf in parallel near the operational amplifier. It is not necessary to try more Rs or Cf to minimize noise. The noise of the output come from the differentiator does not mean that it is harmful, because it also amplifies useful signals. In addition, if disconnect a loop, the differential output noise may be beneficial and will stabilize the loop. If the output of the differentiator is quite noisy or has too much input noise, analyze which are the real sources of them.Q13: How to protect the amplifier input from being higher or lower than the supply voltage?A: What must be done is either to clamp the input of the device, or to limit the input current of the device, or ideally, do both. The easiest way is to choose a current limiting resistor to limit this current. The selection is based on the fact that the current generated by the circuit input at the maximum input voltage is less than the maximum current rating of the input pin. Usually, a 1K to 100K resistor in series with this input pin is effective. However, since the signal is usually connected directly to a non-inverting input pin, a non-inverting amplifier may need a protective resistor connected to this pin. For high impedance circuits, a large resistor and or low leakage current diode can be used.Q14: What is the difference between a single-supply amplifier and a dual-supply amplifier?A: There is no difference in the actual circuit, layout, and characteristics of the amplifier. When an operational amplifier is designated as dual power supply, the output load is usually referenced to ground (GND), while a single power supply operational amplifier is usually referenced to the midpoint voltage of a single supply, and it is usually specified to operate on lower voltages, but this is not a necessary requirement. Therefore, whether the op amp is powered by a single 5V power supply and ground (GND), or powered by +2.5 and -2.5V, these is no different. Ⅳ Application: LM358 Classic CircuitsThis Video is Going to Show Top 5 Electronics Project Using OP-AMP LM358The LM358 includes two independent, high-gain, internal frequency-compensated dual operational amplifiers. It is suitable for single-supply operation with a wide range of power supply voltages. It is also suitable for dual-supply operation. LM358 applications include sensor amplifiers, DC gain modules and all other operational amplifiers that can be powered by a single power supply. The classic circuits of LM358 are as shown as following:Figure 1. Active DC-coupled Low Pass RC Filter Figure 2. LED Driver Figure 3. Transistor-Transistor-Logic (TTL) Drive Circuit Figure 4. Active RC Band Pass Filter Figure 5. Squareware Oscillator Figure 6. Hysteresis ComparatorFigure 7. Active Band Pass filter Figure 8. Lamp Driver Figure 9. Current Monitor Figure 10. Low Drift Peak Detector Figure 11. Voltage Follower Figure 12. Power Amplifier Peripheral CircuitFigure 13. Voltage Controlled Oscillator VCOFigure 14. Fixed Current Source Figure 15. Pulse Generator Figure 16. AC Coupled Non-inverting Amplifier Figure 17. AC Coupled Inverting Amplifier Figure 18. Adjustable Gain Instrumentation Amplifier Figure 19. DC Amplifier Figure 20. Pulse Generator Figure 21. Bridge Current Amplifier Figure 22. Introducing Differential Input Signal Figure 23. DC Differential Amplifier Frequently Asked Questions about Op Amps Basics1. What is an op amp basics for dummies?An op amp is a super-sensitive electronic amplifier circuit that's designed to amplify the difference of two input voltages. Thus, an op amp has two inputs and one output. ... Most op amps require both a positive and a negative voltage power supply, with voltages usually ranging from 6 V to 18 V. 2. What is the basic use of op amp?An operational amplifier is an integrated circuit that can amplify weak electric signals. An operational amplifier has two input pins and one output pin. Its basic role is to amplify and output the voltage difference between the two input pins. 3. What is operational amplifier and its types?An operational amplifier (op amp) is an analog circuit block that takes a differential voltage input and produces a single-ended voltage output. Op amps usually have three terminals: two high-impedance inputs and a low-impedance output port. 4. Which purpose the op amp is used?As the name suggests, the purpose of an amplifier or an op amp is to amplify or increase the input signal to produce an output signal which is much larger than that of the input, with a similar waveform as that of the input. The main change in the output signal will be the increase in the power level. 5. What does it mean when an op amp saturates?Originally Answered: What happens when an op-amp is saturated? that means the amplification or gain is so high as to make the output signal with a given input signal, so large as to exceed the compliance range of the power supply of the ope amp. More simply put, if you have an op amp supplied with +/-15V supply rails.
kynix On 2019-12-28
Ⅰ. Filter DefinitionIn electronics, a filter (signal processing) is a kind of devices or process that removes some unwanted components or features from a signal. Filtering is a class of signal processing, the defining feature of filters being the complete or partial suppression of some aspect of the signal. Most often, this means removing some frequencies or frequency bands. However, filters do not exclusively act in the frequency domain; especially in the field of image processing many other targets for filtering exist. As is known to all, electronic filters remove unwanted frequency components from the applied signal, enhance wanted ones, or both.Introduction to Signal FilteringCatalogⅠ. Filter DefinitionⅡ. Type of Filters and Functions 2.1 Type of Filters 2.2 Filtering FunctionsⅢ. Filter TechnologiesⅣ. Main Characteristic Indexes of FilteringⅤ. Filter Classifications Analysis 5.1 Passive Filter & Active Filter 5.2 Digital Filter & Analog FiltersⅥ. One Question Related Filter and Going Further 6.1 Question 6.2 AnswerⅡ. Type of Filters and Functions2.1 Type of FiltersFilters have different effects on signals of different frequencies. According to this fact, the basic filter types can be classified into four categories: low-pass, high-pass, band-pass, and band-stop. Each of them has a specific application in DSP. One of the objectives may involve digital filters design in applications. Generally, the filter is designed based on the specifications primarily for the passband, stopband, and transition band of the filter frequency response. The filter passband is the frequency range with the amplitude gain of the filter response being approximately unity. The filter stopband refers to the frequency range over which the filter magnitude response is attenuated to eliminate the input signal whose frequency components are within that range. The transition band means the frequency range between the passband and the stopband.Figure 1. Filtering Out the Noise (signal processing)Because there are many different standards of classifying filters and these overlap in many different ways, there is no clearly distinctive classification. Filters may be:non-linear or linearanalog or digitaltime-variant or time-invariant , also known as shift invariance.discrete-time (sampled) or continuous-timepassive or active type of continuous-time filterinfinite impulse response (IIR) or finite impulse response (FIR) type2.2 Filtering FunctionsSeparate useful signals from noise to improve signal immunity and signal-to-noise ratio.Filter out unwanted frequency to improve signal analysis accuracy.Separate single frequency from complex frequencFigure 2. Electronic FilterⅢ. Filter TechnologiesFilters can be built in a number of different technologies. Before that, it is necessary to know some basics of it deeply.Center frequencyThe main parameters of the filter: the center frequency of the filter's pass-band f 0, generally f 0 = (f 1 + f 2) / 2, f 1 and f 2 are boundary frequencies of band-pass or band-stop filter, which decreased by 1dB or 3dB. In addition, narrowband filters often use the smallest point of insertion loss as the center frequency to calculate the pass-band bandwidth. Cutoff frequencyIt refers to the right frequency point of the pass-band of the low-pass filter and the left frequency point of the pass-band of the high-pass filter, and it is usually defined by relative loss points, 1dB or 3dB. The relative reference for the relative loss is: the low-pass is based on the insertion loss at DC, and the high-pass is based on the insertion loss at a high-pass frequency at which no parasitic stop-band occurs. Pass-band bandwidthThe bandwidth of the filter is simply the difference between the upper and lower cutoff frequencies, while passband bandwidth is the difference between the upper and lower cutoff frequencies of, for example, a band-pass filter, a communication channel, or a signal spectrum. Insertion lossIt refers to the loss of the original signal in the circuit due to the introduction of the filter. And it is characterized by the loss at the center or the cutoff frequency. If it is the full-band interpolation loss, it must be emphasized.Note: When adding a filter at the input end, the impedance of the filter should be mismatched with the impedance of the power supply. The more severe the mismatch, the more ideal the attenuation is, and the better the insertion loss characteristics. That is, if the internal resistance of the noise source is low impedance, the input impedance of the EMI filter connected to it should be high (such as a series inductor with a large amount of inductance); if the internal resistance of the noise source is high impedance, the input impedance of the EMI filter should be low (such as a large parallel capacitor). Due to the imbalance of the line impedance, the two components will convert to each other during transmission, and the situation becomes complicated. RippleIt refers to the peak-to-peak value of the insertion loss that fluctuates on the basis of the average loss curve with the frequency in the 1dB or 3dB bandwidth (cutoff frequency). Pass-band riplpeThe amount of change in insertion loss in the pass-band with frequency. For example, in a 1dB bandwidth, it is 1dB. Pass-band standing wave ratio (VSWR)An important indicator for measuring whether the signal in the filter pass-band is properly transferred. Ideal VSWR is 1: 1, when mismatched, VSWR> 1. For an actual filter, bandwidth satisfies VSWR <1.5: 1, which is generally less than 3dB, and the proportion when at 3dB is related to the filter order and insertion loss. Return lossThe decibels (dB) of the ratio of the port's signal input power to the reflected power, and it is also equal to | 20Log10ρ |, where ρ is the voltage reflection coefficient. In addition, when the input power is completely absorbed by the port, the return loss value is infinite. Stop band rejectionIt is a major index to measure the performance of filter selection. The higher the index, the better the suppression of out-of-band interference signals. There are usually two formulations: one is how much dB is required to suppress a given out-of-band frequency fs, and the calculation method is the attenuation fs=As-IL; another is to propose a characterizing filter whose amplitude-frequency response is close to the ideal rectangle index of degree-rectangular coefficient (KxdB> 1), KxdB = BWxdB / BW3dB, (x can be 40dB, 30dB, 20dB, etc.). The more the filter order, the higher the rectangularity, in other words, the closer the K is to the ideal value 1, the more difficult it is to make an ideal filter. Delay (Td)It refers to the time required for the signal to cross the filter. The value is the derivative of the diagonal frequency of the transmission phase function. In-band phase linearityThis indicator characterizes the phase distortion introduced by the filter on the transmission signal in the pass-band. The filter designed according to the linear phase response function, which has good phase linearity, but its frequency selectivity is very poor. It is only used to pulse or phase-modulate signal transmission system applications. Order (stage)For high-pass and low-pass filters, the order is the sum of all capacitors and inductors in the filter circuit. For a band-pass filter, the order is the total number of parallel resonators; for a band-stop filter, the order is the total number of series and parallel resonators. Absolute bandwidth / relative bandwidthThis indicator is usually used for band-pass filters, which characterize the frequency range of signals that can pass through the filter, and reflects the frequency selection of the filter. Relative bandwidth is the percentage of absolute bandwidth to center frequency. Standing waveIt indicates the impedance matching between the filter port and the required system, and also it indicates how much of the input signal failed to enter the filter and was reflected back to the input. LossIt represents the energy lost after the signal passes through the filter, that is, the energy consumed by the filter. Pass-band flatnessThe absolute value of the difference between the maximum loss and the minimum loss in the pass-band of the filter, which characterizes the difference in energy consumption of filters for different frequency signals. Out-of-band rejectionIt is the "attenuation" outside the pass-band frequency range of the filter, which characterizes the filter's ability to select unnecessary frequency signals. Absolute group delayThe time it taken for a signal to pass from the input port to the output port within the pass-band of the filter. Group delay fluctuationThe difference between the maximum and minimum absolute group delay in the pass-band of the filter, which characterizes the dispersion characteristics of a filter. Power capacityIt refers to the maximum power of the pass-band signal that can be input to the filter. Phase consistencyThe difference in the phase of the transmitted signal between different filters of the same index in the same batch, which characterizes the differences (consistency) between batch filters. Amplitude consistencyThe difference of transmission signal loss between different filters with the same index in the same batch, which represents the differences (consistency) between batch filters.Figure 3. Low-Pass Electrical FilterⅣ. Main Characteristic Indexes of FilteringCharacteristic frequency① The pass-band cutoff frequency fp = wp / (2p) is the frequency of the boundary point between the passband and the transition band, at which the signal gain decreases to the specified lower limit.② Stop-band cut-off frequency fr = wr / (2p) is the frequency of the boundary point between the stopband and the transition band, at which the signal attenuation (reciprocal of the gain) decreases to the specified lower limit.③ The corner frequency fc = wc / (2p) is the frequency when the signal power is attenuated to 1/2 (about 3dB). In many cases, fc is often used as the pass-band or stop-band cutoff frequency.④ Natural frequency f0 = w0 / (2p), when there is no loss in the circuit, it refers to the resonance frequency of the filter, and complex circuits often have multiple natural frequencies. Gain and attenuationThe gain of the filter in the pass-band is not constant.① For the low-pass filter pass-band gain Kp, for the ordinary filters, it refers to the gain at w = 0; for the high-pass, it refers to the gain at w → ∞; for the band pass, it refers to the gain at the center frequency.② For the band-stop filter, the stop-band attenuation should be given, and the attenuation is defined as the inverse of the gain.③ The change amount of the pass-band gain △ Kp, refers to the maximum change amount of the gain at each point in the pass-band. If △ Kp is in dB, it means the variation of the gain dB value. Damping coefficient and quality factorThe damping coefficient is a characterization of a filter’s damping effect on a signal with an angular frequency at w0, and is an indicator of energy loss in the filter.The reciprocal of the damping coefficient is called quality factor, and is an important indicator of the frequency selection characteristics of the valence band-pass and band-stop filters, Q = w0 / △ w, where △ w in the formula is the 3dB bandwidth of the band-pass or band-stop filter, w0 is the center frequency, and in many cases the center frequency is equal to the natural frequency. SensitivityThe filtering circuit is composed of many components, and changes of parameter values of each component will affect the performance of the filter. The sensitivity of a certain performance index y of the filter to the change of a certain component parameter x is recorded as Sxy, which is defined as: Sxy = (dy / y) / (dx / x).This sensitivity is not the same concept with the sensitivity of measuring instruments or circuit systems. The smaller the sensitivity, the stronger the fault tolerance of the circuit, and the higher the stability. Group delay functionWhen the filter's amplitude-frequency characteristics meet the design requirements, in order to ensure that the output signal distortion does not exceed the allowable range, certain requirements should be put forward for its phase-frequency characteristic ∮(w). In filter design, the closer the group delay function d∮ (w) / dw is to a constant, the smaller the signal phase distortion. Ⅴ. Filter Classifications Analysis5.1 Passive Filter & Active FilterPassive filterA passive filter is composed of passive components only. It is based on the principle that the reactance of the capacitive and inductive components changes with frequency. The advantages of this type of filter are: simple circuit, causal power supply, and high reliability. Also there are disadvantages: the signal in the pass-band has energy loss, the load effect is relatively obvious, and electromagnetic induction is easy to cause when using inductive components. When the inductance is large, the size and weight of the filter are relatively large, which is not applicable in the low frequency range.The passive filter circuit has a simple structure and is easy to design, but its pass-band magnification and cut-off frequency change with the load, so it is not suitable for occasions with large signal processing requirements. Passive filter circuits are usually used in power circuits, such as filtering after DC power rectification, or LC (inductance, capacitor) circuit filtering when high current loads are used. Active filterActive filters are composed of passive components and active devices. The advantages of this type of filter are that the signal in the pass-band has no energy loss, even be amplified; the load effect is not obvious, and the mutual influence is small when multi-levels are connected. The simple method of cascading is easy to form high-order filter, and the device is small, lightweight, and does not require magnetic shielding. Their disadvantages are that the pass-band range is limited by the bandwidth of the active device and requires a DC power supply; the reliability is not as high as that of a passive filter, and it is not suitable for high voltage, high frequency, and high power applications.The load of the active filter circuit does not affect the filtering characteristics, so it is often used in places with superior signal processing requirements. Active filter circuit is generally composed of an RC network and integrated operational amplifier, so it can only be used under the condition of suitable DC power supply, and it can also be amplified. However, the composition and design of the circuit are also more complicated. Active filter circuits are not suitable for high voltage and high current applications. 5.2 Digital Filter & Analog Filters5.2.1 TerminologyA digital filter is an algorithm or device consisting of a digital multiplier, an adder, and a delay unit. The function of the digital filter is to perform arithmetic processing on the digital code of the input discrete signal to achieve the purpose of changing the signal spectrum. Digital filters can be made by computer software or large-scale integrated digital hardware.There are active and passive analog filters. Active filters mainly consist of op amps, op amps, resistors, and capacitors. They have problems such as voltage drift, temperature drift, and noise, while digital filters do not get these problems, so they can achieve high stability and accuracy. 5.2.2 Differences between Digital filter & Analog filtersDigital filters are used for discrete systems, analog filters are used in continuous-time systems, and they can also be used in discrete-time systems, such as SC (switched capacitor) filters.From the point of view of implementation, analog filters are generally built with analog devices such as capacitors and inductors. Digital filters can be implemented by software or digital chips. It is troublesome to replace the capacitor and inductor when the technique parameters of the analog filter are changed. If there is a need for replacement, it is necessary to modify the coefficients (such as when implemented in software).From the technical view, for example, it is very difficult for analog filters to reach -60dB, and digital filters can easily reach this.The biggest difference between analog and digital filters is that the digital filter on the Fs/2 frequency is flipped, that is, symmetrical, while analog filters are not. Therefore, a large number of interpolation filters are selected in the DAC, and the image frequency is placed at a far frequency point, and then the analog filter regarded as a sound meter is used to filter out the image frequency in the radio frequency band.The expression of analog filters is different from digital filters: analog filters are represented by H (S), and digital filters are represented by H (Z). Analog filter is based on the approximation of amplitude-frequency characteristics, while digital filters can achieve phase matching.Figure 4. EMI Filters ImageⅥ. One Question Related to Filter and Going Further6.1 QuestionHow to Select EMI Filters?6.2 AnswerSome people think that the higher the insertion loss of an EMI filter, the better, and the more stages of the filtering network, the better. In fact, this is not the right way to choose a EMI filter. In addition, the more stages of the filtering network, the more expensive, the larger the size and weight. In practice, the best way to select and evaluate an EMI filter is to install it on a device for testing. As is known to all, the performance of a filter depends largely on the load impedance of the device. It cannot be derived from one data of impedance insertion loss. Because it is a complex function of the filtering element impedance and the equipment impedance, and its magnitude and phase change within the frequency range. What's more, different performance levels of conducted radiation control (FCC, VDE) and sensitivity control required by the filter selection test are performed on the device. Frequently Asked Questions about Filter (Signal Processing) Basics1. What is filter in digital signal processing?In signal processing, a filter is a device or process that removes some unwanted components or features from a signal. Filtering is a class of signal processing, the defining feature of filters being the complete or partial suppression of some aspect of the signal. 2. Why do we use filter in digital signal processing?Digital filters are used for two general purposes:(1) Separation of signals that have been combined(2) Restoration of signals that have been distorted in some way. Analog (electronic) filters can be used for these same tasks; however, digital filters can achieve far superior results. 3. What is filter response?In comparison, filters carried out by convolution are called Finite Impulse Response or FIR filters. As you know, the impulse response is the output of a system when the input is an impulse. In this same manner, the step response is the output when the input is a step (also called an edge, and an edge response). 4. Which filter is present in DSP system?An ideal bandpass filter and second-order approximations. With DSP software, there are two basic approaches to filter design: finite impulse response (FIR) and infinite impulse response (IIR). 5. What are the functions of filter in signal processing?In the field of signal processing, a filter is a device or process that, completely or partially, suppresses unwanted components or features from a signal. This usually means removing some frequencies to suppress interfering signals and to reduce background noise. 6. What is filter frequency?A frequency filter is an electrical circuit that alters the amplitude and sometimes phase of an electrical signal with respect to frequency. ... The frequency separating the attenuation band and the pass is called the cut-off frequency. 7. What is IIR filter in DSP?The infinite impulse response (IIR) filter is a recursive filter in that the output from the filter is computed by using the current and previous inputs and previous outputs. Because the filter uses previous values of the output, there is feedback of the output in the filter structure. 8. Where FIR filter is used?The term FIR abbreviation is “Finite Impulse Response” and it is one of two main types of digital filters used in DSP applications. Filters are signal conditioners and function of each filter is, it allows an AC components and blocks DC components. The best example of the filter is a phone line, which acts as a filter. 9. What are the most commonly used active filters?The most common and easily understood active filter is the Active Low Pass Filter. Its principle of operation and frequency response is exactly the same as those for the previously seen passive filter, the only difference this time is that it uses an op-amp for amplification and gain control. 10. Why IIR filter is unstable?So, for unstable filters, the impulse response is not absolutely summable. In another way, the impulse response never approaches zero. Again, for IIR filter, h continues to go on with n i.e. never goes to zero. So, IIR filters are supposed to be unstable. Recommended ReadingComplete Introduction and Classification of Filters and ApplicationsPrinciple and Function of the FilterCommon Applications of FilterClassification of Electronic Filters
kynix On 2019-12-06
IntoductionAn operational amplifier, or op-amp for short is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op-amp produces an output potential that is typically hundreds of thousands of times larger than the potential difference between its input terminals, and is a voltage amplifying device designed to be used with external feedback components such as resistors and capacitors between its output and input terminals. They are used extensively in signal conditioning, filtering or to perform mathematical operations such as add, subtract, integration and differentiation.In this video, the basic introduction of the Operational Amplifier (Op-Amp) has been given and different characteristics of ideal and real Op-amp (General Purpose 741 Op-Amp) has been discussed. CatalogIntroductionⅠ Operational Amplifier Basics1.1 Amplification Principle1.2 Balance Resistor1.3 Feedback Resistor in Parallel with a Capacitor 1.4 Pulling Down Resistor and Pulling Up the Capacitor1.5 Parasitical Resistor as an Integrator1.6 Parasitical Resistors and Capacitors1.7 Balance Resistor Failure1.8 Magnification, Input Impedence, Voltage1.9 Open Loop Gain1.10 Virtual ShortⅡ Op Amp ApplicationⅢ Op Amp SamplingⅣ Op Amp Reference VoltageⅤ Importance of Op AmpⅠ Operational Amplifier BasicsWhen using op amp, there will be more problems confusing us, what are they? Listing all of them is impossible, but we can seek the core of these problems, which are the following lists.1.1 Amplification PrincipleThere are many types of op amps with many functions, and their circuits are inconsistent, but the internal block diagrams are basically the same. It consists of three parts: input stage, intermediate stage, and output stage. The input stage consists of a differential amplifier circuit that uses circuit symmetry to improve overall circuit, and the main function of the intermediate voltage amplifier stage is to increase the voltage gain. It can be composed of one or more stages of amplifying circuits; the output stage has a voltage gain of 1, but can provide a certain amount of power, and the circuit consists of two power supplies V+ and V-. The entire amplifier circuit is designed with two inputs P and N, and one output O. The voltages of the three terminals are represented by Vp, Vn, and Vo, respectively. The two ends of P and N are respectively called the non-inverting input terminal and the inverting input terminal, which means that when the P terminal is added with the voltage signal Vp (Vn = 0), it is obtained at the output end. The voltage Vo is in-phase with Vp, when the voltage signal Vn (Vp = 0) is applied to the N terminal, the output voltage Vo obtained at the output is inverted from Vp.The operational amplifier is actually a differential amplifier. Look at its structure, two transistors are connected back to back to share the crossing current source. One of the transistors is the positive input of the op amp and the other is the inverting input. The positive input is amplified and sent to a power amplifier circuit to amplify the output. Thus, if the voltage at the forward input rises, the output naturally becomes larger. If the voltage at the inverting input rises, the reverse current is large, and the forward current is small, because the inverting tertiary tube and the forward tube share a same current source.1.2 Balance ResistorGenerally, there is a balance resistor in the inverting / non-inverting amplifier circuit. What is the role of this balance resistor?(1) Provide a suitable static bias for the transistors inside the chip.The internal circuit of the chip is usually directly coupled, and it can automatically adjust the static operating point, but if an input pin is directly connected to the power supply or the ground, its automatic adjustment function can not work normally. Because the voltage of the ground cannot be raised by the inside transistors, and the voltage of the power supply cannot be reduced, which causes the chip to fail to meet the conditions of virtual short and virtual open.(2) Eliminate the influence of the static base current on the output voltage, and the value should be balanced with the equivalent resistance value of the external DC of the two input terminals.(3) In non-inverting op amp circuit, if it not connecting a balance resistor, the op amp will be burned, because the resistor acts as a voltage divider. 1.3 Feedback Resistor in Parallel with a Capacitor What is the role of the feedback resistor in parallel with a capacitor when using non-inverting op amp?(1) The feedback resistor and capacitor form a high-pass filter, so that local high-frequency amplification is particularly noticeable.(2) Prevent self-excitation. 1.4 Pulling Down Resistor and Pulling Up the CapacitorWhat role does the role of pulling down resistor and pulling up the capacitor at the input of the op amp play?To get positive feedback and negative feedback, depending on the specific circuit connection. For example, if the input voltage signal and the output voltage signal are taken to the input, the partial output signal passes through the balance resistor to obtain a new voltage value, that is, shunting the input voltage to make the input voltage smaller, and this is a negative feedback. Since the signal output from the signal source is always constant, the output signal can be corrected by negative feedback. 1.5 Parasitical Resistor as an IntegratorWhat is the function of the resistor RF connected to the op amp as an integrator at the two ends of the integrating capacitor?Adjust resistance to prevent the output voltage from running out of control. 1.6 Parasitical Resistors and CapacitorsWhy are resistors and capacitors connected in series at the input of the op amp?Regardless of the type of op amp, it consists of transistors or MOS transistors. In the absence of an external components, the op amp is a comparator actually. When the voltage of the non-inverting terminal is high, it will output a level similar to the positive voltage, and vice versa, but this op amp does not seem to have much use. Only when the external circuit is formed to generate the feedback will make the real op amp function. 1.7 Balance Resistor FailureWhat is the consequence of the balance resistor doesn't work well in non-inverting amplifier circuit?(1) The non-inverting end is unbalanced. For example, there will be an output although the input is 0. When the input signal is output, the output value is always larger (or smaller) than the theoretical output value by a fixed number.(2) The error caused by the input bias current cannot be eliminated. 1.8 Magnification, Input Impedence, VoltageWhat is the amplification factor and input impedence of an ideal integrated operational amplifier? What is the voltage between the non-inverting input and the inverting input?The magnification is infinite, the input impedance is infinitesimal, and the voltage is almost the same (the voltage is not 0V, for example, the non-inverting end is 10V and the inverting end is 9.99V). 1.9 Open Loop GainWhy is the open loop gain of an ideal op amp infinite?1) The actual open loop gain of the op amp is very large, so imagine it as infinity and derive the virtual ground from it.2) Deriving virtual ground is not only an inverting amplifier for the negative feedback connection, because there is no virtual ground for positive feedback.The open-loop gain of the op amp is infinite, when design the circuit, the closed-loop gain can be independent of the open-loop gain, and only depends on the external components. It is to use the large open loop gain in exchange for the stability of the closed loop gain.3) Assuming that the gain is small, the difference between the voltages applied across the op amp is relatively large for an output voltage. If it is connected to a negative feedback state, the voltage across the op amp will be different, causing amplification.We all know that the op amp’s output voltage Vo is equal to the difference Vid between the non-inverting input voltage and the inverting input voltage, multiplied by the op amp’s open-loop gain A, that is, Vo = Vid * A = (VI + - VI-) * A ( 1 ). Since the output voltage of the op amp does not exceed the supply voltage in practice, it is a finite value. In this case, if A is large, (VI+ - VI-) is necessarily small; if (VI+ - VI-) is small enough, then we can actually treat it as 0, at this time, there will be VI+ = VI-, that is, the voltage at the non-inverting input of the op amp is equal to the voltage at the inverting input. This is what we call “virtual short”. Note that they are not really connected together, and there is resistance between them.In the above discussion, how did we get the result of “virtual short”? Our starting point is the formula (1), which is based on the characteristics of the op amp. Then, we made two important assumptions, one is that the output voltage of the op amp is limited, and it not exceed the power supply voltage; the second is that the open loop gain A of the op amp is large. The A of a normal op amp usually reaches 106 or 107 or even larger, but the actual open loop gain of the op amp is also related to its working state. For example, if the op amp is not working in the linear area, the value A may be small, so second assumption is conditional.Therefore, we know that when the open loop gain A of the op amp is large, the op amp can have a virtual short. But it is one of the possibilities, and it is not suitable for every op amp in any case to say their inputs are virtual short, in other words, virtual short can only be achieved in circuits under certain conditions.The conditions of virtual short:a. The open-loop gain of operational amplifier should be large enough.b. There should be a negative feedback circuit. From the above we know when we need to analyze the virtual short in the circuit. In reality, condition (1) is true for most op amps, and the important point is to look at the work area. If it is a circuit drawing, judge by calculation; if it is an actual circuit, it is reasonable to use the instrument to measure amplifier output voltage.There is also a situation related to virtual short called “virtual ground”, that is, there is a virtual short when the input is grounded. Some books say that virtual short will be exist under deep negative feedback conditions, but in reality, the op amp is more likely to work in the linear region under this situation. But this is not absolute, when the input signal is too large, the op amp with deep negative feedback will still be saturated. Therefore, it should be judged to be the most reliable with the output voltage value. 1.10 Virtual ShortAdd the input signal directly to the non-inverting input, and the inverting input is grounded through the resistor. Why is U-= U+ = Ui≠0? Is it not a virtual short? What are the conditions that the virtual ground exists?(1) In the non-inverting amplifier circuit, the output affects by the feedback, so that U(+) automatically tracks U(-), so they will be close to zero. It seems that the two ends are short circuit, so it is called virtual short.(2) Due to the virtual short phenomenon and the high input resistance of the op amp, the current flowing through the two input terminals is small, approaching 0. This phenomenon is called virtual open, which is derived from virtual short.(3) The virtual ground is in the inverting op amp circuit, the (+) terminal is grounded, and the (-) is connected to the input and feedback network. Due to the virtual short, U(-) and U(+) are very close, which is said to be virtual ground.(4) About the conditions: the virtual short is an important feature of the closed-loop (negative feedback) operating state of the non-inverting amplifier circuit; the virtual ground is an important feature of the inverting amplifier circuit in the closed-loop operating state. Ⅱ Op Amp ApplicationWhen a operational amplifier is connected as a non-inverting amplifier, the potentials of the two inputs are the same. If the waveform of the input is measured, it will be the same. This is like a common-mode signal. In fact, there are still small differential mode signal on the two inputs, but the differential mode signal can not be measured by the general instrument. As a result, the virtual short artificially increases the common-mode signal at the two inputs, which poses a challenge to the performance of the operational amplifier. Why is an op amp used like this?(1) The common mode signal of the non-inverting amplifier is much larger than the inverting amplifier, and strict to the common mode rejection ratio.(2) For single-ended input, the equivalent common-mode value is half of the input value, whether non-inverting or inverting input. However, since the input impedance of the non-inverting amplifier is usually larger than the inverting amplification, the anti-interference ability is a little poor.As mentioned above, when the inverting input is performed, the voltage at the inverting terminal is almost zero, so the differential influence on the tube collector voltage that has only one tube change. When the input is in phase, the voltage at the inverting terminal is equal to the non-inverting terminal voltage, so the common mode voltage and the input voltage are equivalent. That is to say, the collector voltage of the differential tube has variable quantity that changes in the same direction when the two tubes have portions that change in different directions at the same time, which is the common mode output voltage. It is added in phase with the voltage of one of the tubes. Therefore, it is easy to cause the tube to become saturated (or cut off), fortunately, the amplification of the common mode voltage is only tens of thousands of parts of the differential mode amplification.However, this does not mean that the common mode rejection suppression ratio of the differential mode input and the common mode input of the amplifier is different. It should be that the non-inverting input is added with a common mode signal equivalent to the input volume, so it should be careful to use non-inverting amplification mode when the input signal is large. Ⅲ Op Amp SamplingWhy is the amplifier circuit composed of operational amplifiers generally sampling the inverting input mode?(1) The significant difference between the inverting input and the non-inverting input mode is:When inverting input, because there is a balanced resistor connected to the ground at the same phase, and there is no current on this resistor (because the input resistance of the op amp is extremely large), this non-inverting terminal is approximately equal to the ground potential, and the potential at the non-inverting terminal is extremely close to the inverting terminal, so there is a virtual ground at the inverting end. The advantage of having a virtual ground is that there is no common mode input signal, even if the common mode rejection ratio is not high, there is no common mode output. The non-inverting input mode has no virtual ground. When a single-ended input signal is used, a common-mode input signal is generated. Even if an operational amplifier with a high common-mode rejection ratio is used, there is still a common-mode output. Therefore, it is best to use the inverting input method.(2) The positive phase is the oscillator, and the inverting can stabilize the amplifier and access the negative feedback.(3) From the principle point of view, it is possible to connect to the same analog circuit. However, the signal (differential mode signal) that is amplified during the actual application tends to be small, thus it is necessary to pay attention to suppressing noise (usually expressed as a common mode signal). In the same way, the amplification circuit has a poor ability to suppress the common mode signal, and the signal that needs to be amplified is submerged in the noise, which is not conducive to post processing. Therefore, an inverting proportional amplification circuit with better suppression capability is good.Ⅳ Op Amp Reference VoltageSome op amps will have an output even if no voltage is input after power-on, and the output is not small, so VCC/2 is often used as the reference voltage.The output is output signal without any input, this is called the input offset voltage Vos, which is caused by the asymmetry of the design structure of the op amp. It is a very important performance indicator of the op amp. The op amp commonly used VCC/2 as the reference voltage is because the op amp is in a single power supply state. At this time, the real reference of the op amp is VCC/2, so a DC offset of VCC/2 is often provided at the positive terminal of the op amp. When having positive and negative dual power supply, it is often referenced to the ground.The selection of op amps requires attention to many things. Under less stringent conditions, it is often necessary to consider the operating voltage, output current, power consumption, gain bandwidth product, and price of the op amp. Of course, when using it under special conditions, different factors must be considered in practice. Ⅴ Importance of Op Amp(1) If the voltage on both inputs of the op amp is 0V, the output voltage should also be equal to 0V. But in fact, there is always some voltage at the output, that is, the offset voltage Vos. If the offset voltage at the output is divided by the noise gain of the circuit, the calculated result is called the input offset voltage or the input reference offset voltage. The Vos is considered to be a voltage source in series with the inverting input of the op amp. A differential voltage must be applied to both inputs of the amplifier to produce a 0V output.(2) The input impedance of an ideal op amp is infinite, so no current flows into the input. However, a real op amp using a bipolar junction transistor (BJT) in the input stage requires some operating current, which is called bias current (IB). There are usually two bias currents: IB+ and IB-, which flow into the two inputs, respectively. The range of IB values is large, with bias currents of lower at 60fA for special op amps and up to tens of mA for some high-speed op amps.(3) The power supply voltage range required for the first single-chip op amp to operate normally is ±15V. Today, op amps are moving toward low voltages due to increased circuit speeds and power supplies from low-power sources such as batteries. Although the op amp’s voltage specifications are usually specified as symmetrical two-pole voltages ±15V, these voltages do not necessarily require a symmetrical voltage or a two-pole voltage. For an op amp, as long as the input is biased in the active region (within the common-mode voltage range), the ±15V supply is equivalent to a +30V/0V supply, or a +20V/-10V supply. The op amp does not have a ground pin unless the negative voltage rail is grounded in a single-supply application.The input voltage swing of high speed circuits is smaller than that of low speed devices. The higher the speed of the device, the smaller its geometry, which means the lower the breakdown voltage. Due to the low breakdown voltage, the device must operate at a lower supply voltage. Today, op amps typically have a breakdown voltage of around ±7V, so high-speed op amps can work at a supply voltage of ±5V, and they can also operate at a single supply voltage of +5V.For general-purpose op amps, the supply voltage can be as low as +1~8V. These op amps are powered by a single power supply, but this does not mean that a low supply voltage must be used. Because the terms single supply voltage and low voltage are two related and independent concepts. Frequently Asked Questions about Operational Amplifiers Problems1. How can you tell if an op amp is blown?Re: how to tell whether an op amp is burned out? measure the DC voltage at the +input. then measure the DC voltage at the output. if the results are significantly different, the opamp is most likely shot. 2. How do I know if my op amp is broken?measure the DC voltage at the +input. then measure the DC voltage at the output. if the results are significantly different, the opamp is most likely shot. if they are the same, the opamp is most likely ok and the problem is something else. 3. What errors you have to consider with real operation amplifiers?These errors include input bias current, input offset current, input offset voltage, CMRR, PSRR, and finite input impedance. In reality, all these errors will occur at the same time. 4. How do op amps fail?The common failures I have seen including with comparators involve either the output being shorted or open to one supply or the input differential pair or input protection circuits being damaged causing excessive input bias current and/or input offset voltage which usually ends up pinning the undamaged output. 5. Why do op amps fail?The common failures I have seen including with comparators involve either the output being shorted or open to one supply or the input differential pair or input protection circuits being damaged causing excessive input bias current and/or input offset voltage which usually ends up pinning the undamaged output.
kynix On 2019-11-22
CatalogⅠ What is Biosensor?Ⅱ Principle of Biosensors Ⅲ Characteristics of Biosensors Ⅳ Types of Biosensors 4.1 Acoustic Biosensor 4.2 Optical Biosensor 4.3 Magnetic Biosensor 4.4 Electrochemical Biosensor 4.5 Optical Fiber Nano BiosensorⅤ FAQⅠ What is Biosensor?Biosensor is an instrument that is sensitive to biological substances and converts its concentration into an electrical signal for detection. Biosensor has the function of receiver and converter. Because enzyme membrane, mitochondrial electron transport system particle membrane, microbial membrane, antigen membrane and antibody membrane have the selective recognition function to the molecular structure of biomaterials and only have the catalytic activation function to specific reactions, so biosensors have very high selectivity. The disadvantage is that the biofilm is not stable.Biosensors are mainly used in clinical diagnosis, treatment monitoring, fermentation industry, food industry, environment and robotics. Biosensor is an interdisciplinary subject combining bioactive materials(Enzyme, protein, DNA, antibody, antigen, biofilm, etc)with physical and chemical transducers. It is an advanced detection method and monitoring method necessary for the development of biotechnology, and it is also a rapid and microanalysis method at the molecular level. In the 21st century, in the development of the knowledge economy, biosensor technology will be a new growth point between information and biotechnology. It will have a wide application prospect in clinical diagnosis, industrial control, food and drug analysis(including biopharmaceutical research and development), environmental protection, biotechnology, biochip and other research in the national economy. All kinds of biosensors have the following common structures: including one or several related bioactive materials(Biofilm) and physical or chemical transducers(sensors) that can convert the signals expressed by bioactivity into electrical signals. The two are combined to reprocess the biological signals with modern microelectronics and automatic instrument technology to form a variety of usable biosensor analysis devices, instruments and systems.Ⅱ Principle of Biosensors The substance to be measured enters into the bioactive material through diffusion, and after molecular recognition, biological reaction occurs. The information generated is then transformed into a quantitative and treatable electrical signal by the corresponding physical or chemical transducer, and then amplified and output by the secondary instrument, the concentration of the substance to be measured can be known.Ⅲ Characteristics of Biosensors (1)The biosensor uses the immobilized bioactive substance as the catalyst, and the expensive reagent can be reused many times, which overcomes the shortcomings of the high cost of enzyme analysis reagent and complicated chemical analysis in the past. (2)Strong specificity only reacts to a specific substrate, and not affected by color and turbidity. (3)The analysis speed is fast, and the results can be obtained in one minute. (4)High accuracy; general relative error can reach 1%. (5)The operating system is simple and easy to realize automatic analysis. (6)Low cost; only a few cents per measurement in continuous use. (7)Some biosensors can reliably indicate the oxygen supply and by-products in the microbial culture system. In the process of production control, much complex information can be obtained only by the comprehensive action of physical and chemical sensors. At the same time, they also pointed out the direction of increasing the yield of products.Ⅳ Types of BiosensorsAccording to the classification of life substances used in biosensors, biosensors can be divided into microbial sensors, immune sensors, tissue sensors, cell sensors, enzyme sensors, DNA sensors, etc. According to the principle of sensor detection, it can be divided into a thermosensitive biosensor, FET biosensor, piezoelectric biosensor, optical biosensor, acoustic channel biosensor, enzyme electrode biosensor, mediator biosensor, etc.According to the type of interaction between sensitive substances, it can be divided into two types: affinity type and metabolism type. 4.1 Acoustic BiosensorAcoustic biosensor is a kind of sensor to detect the change of acoustic frequency caused by the substance to be detected. Among them, quartz crystal microbalance(QCM) biosensor has been studied most. In the piezoelectric crystal of quartz crystal microbalance biosensor, AT mode is often used to form two parallel metal((Au,Ag,Pt,Ni,Pd etc.)) membrane electrodes on both sides of the crystal by ion beam deposition. (At cutting means that the cutting surface is 25.15 ° to the main optical axis of quartz crystal. At this moment, the temperature coefficient of crystal resonance is close to zero at room temperature)The recognition molecules are fixed on the surface of the membrane electrode. Because of their specificity, the recognition molecules combine with the molecules to be detected, causing the quality change of the electrode surface, thus changing the oscillation frequency of the quartz crystal. If the nanoparticles are modified on the molecules to be detected, the quality of the molecules to be detected will be significantly improved, and the detection signal will also be enhanced. Ward et al. Labeled the antibody with nano colloidal particles, and combined it to the surface of quartz crystal by antibody antigen immunoassay. Because the modified colloidal particles(The diameter of sol particles is 5 "100nm) improved the quality of the labeled molecules, according to Sauerbrey equation, the oscillation frequency of quartz crystal was correspondingly increased, so the detection signal was amplified, the detection sensitivity was improved, and the detection lower limit was also reduced.4.2 Optical BiosensorNano metal particles can be used for optical resonance detection. Bauer et al. Fixed nano-metal particles on the surface of conductive materials by antigen-antibody or protein receptor binding methods. Due to the interaction of reflection dipoles of nanoparticles, the resonance of reflected light is enhanced. The materials to be detected can be detected by detecting resonance signals. Nanoparticles can also be used to locate tumors. Fluorescein labeled recognition factors bind to tumor receptors, and then the size and location of tumors can be displayed in vitro. Nano metal particles can also be used as a general fluorescent annihilation group. Maxwell and other scientists labeled gold nanoparticles and fluorescence excitation groups at both ends of oligonucleotide probe molecules respectively. The probe formed a "hairpin" structure due to complementary bases, and the proximity of fluorescence excitation group and gold nanoparticles resulted in excitation fluorescence annihilation. When the probe combined with specific target DNA, its conformation changed, and the gold nanoparticles and fluorescence excitation groups were separated, so as to excite Fluorescence. The principle can be used for real-time fluorescence detection of nucleic acids and single base mutation polymorphism detection.4.3 Magnetic BiosensorMagnetic nanoparticles have important application value in biological detection and drug analysis. By using magnetic materials to label biomolecules and molecular recognition technology, complex operations such as sample mixing, separation and detection can be realized. Scientists label molecules with magnetic materials, and realize the separation and detection of samples under the magnetic field gradient. Richardson et al. Used magnetic counter to detect magnetic labeled molecules by magnetic immunoassay. In addition, the distribution and position of magnetic particles in vivo can be measured in vitro after the identification factor is labeled with nanomagnetic particles and combined with the target recognition device on the tumor surface, so as to locate the tumor. Chemla and other scientists used paramagnetic nanoparticles and a microscope based on high-temperature transient DC superconducting quantum interface device (SQUID) to propose a novel rapid detection technology for biological samples. Firstly, the magnetic particles of the fixed antibody are suspended in the solution, and then the magnetized nanoparticles are generated under the instantaneous magnetic field pulse. When the magnetic field disappears, the particles tend to be free distribution, because the particles without the antibody are Brownian motion, so there is no detection signal; while the nanoparticles with the target molecule move in the way of Neel relaxation, resulting in a slowly attenuated magnetic signal, The substance to be detected can be analyzed by the signal collected by the squid. This technology can directly detect the labeled molecules without separating the nanoparticles which are not combined with the molecules to be detected, which shortens the detection time and improves the detection efficiency.4.4 Electrochemical BiosensorColloidal gold is the most common metal nanoparticles, which can be used to mark biomolecules, thus realizing signal detection and amplification; in addition, it can also be widely used in TEM, SEM characterization and paper strip color. Many literatures also reported the signal amplification of colloidal gold in various biosensors. Gonzalez Garcia and other scientists used colloidal gold labeling and electrochemical methods to study the interaction between biotin and avidin. By modifying biotinylated albumin on the electrode surface and then reacting with avidin labeled by colloidal gold with a diameter of 10 nm, scientists found that the current response caused by colloidal gold was linearly related to the concentration of avidin(2.5×10-9mol/L "2.5×10–5mol/L). Nanoparticles have an excellent specific surface area, which can be used to immobilize biomolecules, increase the number of fixed molecules, and achieve signal amplification. Singh and other scientists used the sol-gel method to synthesize silicon nanoparticles with a diameter of 20 nm or 200 nm. Acetylcholinesterase immobilized on the surface of nanoparticles can be used to make organophosphorus pesticide biosensor. Because of its high specific surface activity, combined with the detection of ion-sensitive field effect tube, the metal nanoparticles with rapid response can be used as the carrier of catalyst, which can greatly improve the performance of catalyst. Enzyme colloidal gold is fixed on the surface of the electrode and can be used for the electrochemical detection of H2O2, glucose, xanthine and hypoxanthine. Xu et al. Modified the surface of the screen-printed carbon electrode with colloidal gold, combined with immunity and horseradish peroxidase (HRP) to make H2O2 biosensor. The results showed that the electrocatalytic performance and current response of HRP were significantly improved, the linear range of signal was greatly improved(0.8μM"1.0mM), and the detection limit was also reduced to 0.4 μ M.4.5 Optical Fiber Nano BiosensorCompared with other types of biosensors, fiber-optic nano biosensors are not only small in size and high insensitivity, but also free from electromagnetic interference and do not need reference devices. It can enter the interior of cells and measure the changes of structure and cytoplasm in vivo. (1)Optical fiber nano fluorescence biosensorKopelman was the first to use a fluorescent fiber-optic nanosensor to detect the pH value in the microenvironment. Its working principle is to fix the fluorescent agent at the head of the optical fiber. When the fluorescent agent reacts reversibly with the proton, the optical property of the liquid changes. According to the change of the fluorescence intensity, the pH value can be determined. The optical fiber processing method is as follows: the optical fiber is drawn into a fiber probe with a head diameter of 100nm "1000nm by a fiber drawing instrument, and aluminum is plated on the surface of the optical fiber by a vacuum evaporator to prevent light from leaking during transmission. Then, the exposed optical fiber head is silanized, and the surface is modified into an active surface containing hydroxyl or amino group, and the antigen or antibody of the molecule to be detected is fixed and identified. Finally, the light The fiber head is combined with a pH selective fluorescent dye polymer. The response time of the nano sensor is 250ms, and it can detect the ion concentration of μ M. These characteristics are suitable for the detection of single cell and subcellular structure, such as the detection of pH value of mouse embryonic cell fluid. (2)Optical fiber nano immune biosensorOptical fiber nano immunosensor is a kind of sensor which applies optics and photonics technology to immunoassay. It can convert the amount of antigen or antibody to optical signal by using the characteristic that antigen and antibody can combine specifically. This kind of sensor combines the advantages of traditional immunoassay, optics and biosensor technology, and has high specificity, sensitivity and stability. At the same time, the fiber-optic nano immune sensor only uses nano products on sensitive components, so it not only retains many advantages of the original but also makes it suitable for the measurement of single cells. Dinh et al. Have successfully developed an optical fiber nano immunosensor for the detection of BPT (benzopyrene tetrol, a biomarker of DNA damage related to exposure to carcinogenic benzo [α] pyrene). They first made quartz fiber with a diameter of 10nm "100nm with a fiber drawing instrument, then silanized the fiber head, modified the fiber head with BPT antibody, and then plated the whole length of the fiber (except the modified fiber head) with silver to prevent light from leaking out. Finally, cell puncture and detection experiments were carried out on a single cell operated micromanipulator/microinjector, they used photomultiplier PMT to record the fluorescence produced by the binding of BPT and antibody, and detected the content of BPT in cells by measuring the change of fluorescence intensity. The minimum detection limit of the sensor can reach 10 – 21mol. Ⅴ FAQ1. What is the principle of piezoelectric biosensors?Piezoelectric Biosensors are also known as Acoustic Biosensors as they are based on the principle of sound vibrations i.e. acoustics. When a mechanical force is applied to a piezoelectric biosensor, they produce an electrical signal. The biological elements are attached to the surface of the piezoelectric biosensor. 2. What are the different types of biosensors?• Electrochemical Biosensors.• Magnetic Biosensors.• Thermometric Biosensors.• Acoustic Biosensors.• Optical Biosensors. 3. How does a basic biosensor work?The term ‘biosensor’ is short for ‘biological sensor.’ The device is made up of a transducer and a biological element that may be an enzyme, an antibody or a nucleic acid. The bio element interacts with the analyte being tested and the biological response is converted into an electrical signal by the transducer. 4. What are the main components of biosensors?A biosensor typically consists of a bio-receptor (enzyme/antibody/cell/nucleic acid/aptamer), transducer component (semi-conducting material/nanomaterial), and electronic system which includes a signal amplifier, processor & display. Transducers and electronics can be combined, e.g., in CMOS-based microsensor systems. 5. How do you classify biosensors?Biosensors can be classified according to the transduction methods they utilize (Fig. 4). Most forms of transduction can be categorized in one of five main classes: electrochemical, electrical, optical, piezoelectric (mass detection methods) and thermal detection. 6. What are wearable biosensors?Wearable systems are devices that allow physicians to overcome the limitations of technology and provide a response to the need for monitoring individuals over weeks or months. Wearable Biosensors typically rely on wireless sensors enclosed in bandages or patches or in items that can be worn. 7. What is an amperometric biosensor?Amperometric biosensors are self-contained integrated devices based on the measurement of the current resulting from the oxidation or reduction of an electroactive biological element providing specific quantitative analytical information. 8. What is voltammetric biosensor?Cyclic Voltammetry (CV) Voltammetry belongs to a category of electro-analytical methods, through which information about an analyte is obtained by varying potential and then measuring the resulting current. It is, therefore, an amperometric technique. 9. What is the electrochemical biosensor?An electrochemical biosensor is a self-contained integrated device, which is capable of providing specific quantitative or semi-quantitative analytical information using a biological recognition element (biochemical receptor) which is retained in direct spatial contact with an electrochemical transduction element. 10. What are Piezoelectric Biosensors?Piezoelectric biosensors are a group of analytical devices working on the principle of affinity interaction recording. A piezoelectric platform or piezoelectric crystal is a sensor part working on the principle of oscillations change due to a mass bound on the piezoelectric crystal surface.
kynix On 2019-11-20
Introduction Diodes are widely used in electronics, such as rectification in power supply, as detection and mixing, etc. in communications, and are often used in voltage regulation and protection in various circuits (such as freewheeling diodes, TVS and so on). Due to the wide variety and versatility, the following is an analysis of the simple application of Schottky diodes in digital circuits.In this video, the Schottky diode has been explained.CatalogIntroductionⅠ Schottky Diodes CharacteristicsⅡ Schottky Diode Applications2.1 As Dual Power Supply2.2 As AND Gate2.3 As OR GateⅢ Schottky Diode ParametersⅣ Example AnalysisⅠ Schottky Diodes CharacteristicsThe Schottky diode is structurally different from the PN junction diode. It is made of an anode metal (a barrier layer made of a material such as molybdenum or aluminum), SiO2 (electric field eliminating material), and N- epitaxial layer (arsenic material), the N-type silicon substrate, N+ cathode layer, and the cathode metal, which are as shown in the following figure. A Schottky barrier is formed between the N-type substrate and the anode metal. When a forward bias is applied to both ends of the Schottky barrier (anode metal is connected to the positive electrode of the power supply, and the N-type substrate is connected to the negative electrode), the Schottky barrier layer is narrowed, and the internal resistance becomes small. On the contrary, when a reverse bias is applied across the Schottky barrier, it becomes wider and its internal resistance becomes larger. Figure 1. Schottky Diode Structure Ⅱ Schottky Diode ApplicationsThe problem with Schottky diodes is that the withstand voltage is relatively low and the reverse leakage current is large. At present, the general condition of the Schottky diode used in the power conversion circuit is that the withstand voltage is below 150V, the average current is below 100A, and the reverse recovery time is between 10 and 40ns. Therefore, Schottky diodes are ideal device for use in high frequency and low voltage circuits.2.1 As Dual Power SupplyAt present, in the electronic design with the main controller, the real-time clock (RTC) is basically used, and the RTC needs an additional button battery to support, to avoid information lost after the system is powered off. And meanwhile, after the system is started, in order to extend the battery life, the main system is often supplied with power. Therefore, RTC often requires dual power supply, and the diode can be used for power isolation due to its single-conductivity. Taking the small-signal Schottky diode BAT54C as an example, the forward voltage drop is only 0.24v (the forward current is 0.1mA), and the RTC current consumption is uA-level, after adding the Schottky diode to isolate power supply to save info security.2.2 As AND GateAs shown in the figure below, n Schottky diodes form the AND gate of the n input. As long as there is a signal output logic 0 in A1~An, the Output is logic 0, only all signals in A1~An output logic 1, Output can output logic 1. That is, the phase sum of the signals A1~An is realized. Since the chip signal input stage is basically high-resistance in the digital circuit, the overall current of the AND gate circuit composed of the Schottky diode is uA-level, and the Schottky diode voltage drop is extremely small. In the case of it, the flat can still meet the design requirements. Figure 2. Schottky Diode as AND Gate2.3 As OR GateAs shown in the figure below, n Schottky diodes form an n-input OR gate. As long as there is a signal output logic 1 in A1~An, Output outputs a logic 1. Only all signals in A1~An output logic 0, and Output can output logic 0. That is, the phase sum of the signals A1~An is realized. Figutre 3. Schottky Diode as OR Gate Ⅲ Schottky Diode ParametersNote: Because Schottky diodes are used differently in different electronic circuits, we also need to consider the following parameters when using them.1)Forward voltage drop VFVF is the forward voltage drop when the diode is forward conducting. The greater the current through the diode, the larger the VF, in addition, the higher the diode temperature, the smaller the VF.2)Reverse saturation drain current IRIR refers to the current flowing through the diode when a reverse voltage is applied to the diode. The Schottky diode has a large reverse leakage current, therefore, selecting a Schottky diode with a smaller IR.3)Rated current IFIt refers to the average current value calculated from the allowable temperature rise when the diode is in a long time operation.4)Maximum surge current IFSMExcessive forward current that is allowed to flow. It is not a normal current, but an instantaneous current, which is quite large.5)Maximum peak inverse voltage VRMEven if there is no reverse current, as long as the reverse voltage is continuously increased, the diode will be damaged sooner or later. This reverse voltage is not the instantaneous voltage, but the reversed voltage that is added repeatedly. Since the rectifier is supplied with an alternating voltage, its maximum value is a specified important factor. And the maximum reverse peak voltage VRM refers to the maximum reverse voltage that can be applied to avoid breakdown. At present, Schottky's highest VRM value is 150V.6)Maximum DC reverse voltage VRVR is the value when the DC voltage is continuously applied. For DC circuits, the maximum DC reverse voltage is important to determine the allowable and upper limits.7)Maximum operating frequency FMDue to the junction capacitance of the PN junction, when the operating frequency exceeds a certain value, its unidirectional conductivity will deteriorate. And Schottky diodes have high FM values up to 100 GHz.8)Reverse recovery time TrrWhen the operating voltage changes from a forward voltage to a reverse voltage, the ideal operation of the diode is that the current can be instantaneously turned off. In fact, it usually takes a little delay. The amount that determines the current cut-off delay is the reverse recovery time. Although it directly affects the switching speed of the diode, it does not mean that this value is small. That is, when the diode is suddenly reversed by conduction, the reverse current is greatly attenuated to a time required to approach IR. This indicator is important when the high-power switch is operating in the high-frequency state.9)Maximum dissipation power PWhen a current flows through the diode, it absorbs heat and raises its temperature. In reality, the external heat dissipation condition also has a great influence on P. Specifically, the voltage applied across the diode is multiplied by the current flowing through and the reverse recovery loss. Schottky Diode Symbols Ⅳ Example AnalysisIn digital circuit design, it is often necessary to make simple phase, or phase inversion of some signals. If the logic chip such as the 74 series is directly used, not only the layout area is greatly increased, but also the wiring is not flexible. The use of small-signal Schottky diodes and OR gates is more flexible and easy to use. The following figure shows a simple two-way reset circuit. JTAG generating a reset signal needs to reset the master, and the external reset button also needs to reset the master when pressed. If the JTAG reset and button reset directly to the reset pin of the master, it may cause damage to the JTAG emulator. For example, when the reset button is pressed, the JTAG output reset pin will be directly lowered. The phase and circuit are formed by the Schottky diode BAT54A , and the signal outputs do not affect each other. The following figure allows the master to reset as long as the JTAG output logic 0 or pressing the button reset output logic 0.Figure 4. Schottky Diode BAT54A ApplicationIf it is to be used as a non-gate, a triode can be used. Of course, the triode is widely used in electronics, such as a switching device in a digital circuit, as a current drive, level shifter, and the like. Frequently Asked Questions about Small Signal Schottky Diodes1. What is the Schottky diode and how it works?A typical diode combines p-type and n-type semiconductors to form a p-n junction. In a Schottky diode metal replaces the p-type semiconductor. This metal can range from platinum to tungsten, molybdenum, gold, etc. When metal is combined with an n-type semiconductor an m-s junction is formed. 2. What does small signal mean?A small signal is an AC signal (more technically, a signal having zero average value) superimposed on a bias signal (or superimposed on a DC constant signal). This resolution of a signal into two components allows the technique of superposition to be used to simplify further analysis. 3. Which statement is correct for Schottky diode?Explanation: The majority charge carriers in a Schottky diode are electrons not holes. Explanation: Due to the metal-silicon junction there are no stored charges hence, no reverse recovery time, due to which the switching is faster. 4. What are the two important features of a Schottky diode?We have seen here that the Schottky Diode also known as a Schottky Barrier Diode is a solid-state semiconductor diode in which a metal electrode and an n-type semiconductor form the diodes ms-junction giving it two major advantages over traditional pn-junction diodes, a faster switching speed, and a low forward bias.
kynix On 2019-11-15
The devices or components commonly used in electronic circuits include: resistors, capacitors, inductors, sensors, potentiometers, transformers, diodes, bipolar junction transistors (BJTs), photoelectric switches, resonators, oscillators, filters, silicon controlled rectifiers (SCRs), relays, dual inline package (DIP) switches, fuse holders, bridge rectifiers, emitters, reed switches, common mode chokes and ferrite beads, magnetic rings, etc. This article contains a lot of commonly used electronic components figures, and I hope you will find this information useful.A Simple Guide to Electronic Components FAQ1. What are basic electronic components?You will work with a number of basic electronic components when building electronic circuits, including resistors, capacitors, diodes, transistors, and integrated circuits. 2. What are electronic components called?They are also called Electrical elements or electrical components. e.g. Resistors, Capacitors, Diodes, Inductors. 3. What are the 3 classification of electronic components?Classification of Electronic Components: Components can be classified as passive, active, or electro-mechanic components.Active components are devices that can amplify an electric signal and produce power.Passive components can't introduce net energy into the circuit. 4. What are the two types of electronic components?These are of 2 types: Passive and Active Components. 5. What is passive electronic components?A passive element is an electrical component that does not generate power, but instead dissipates, stores, and/or releases it. Passive elements include resistances, capacitors, and coils (also called inductors). These components are labeled in circuit diagrams as Rs, Cs and Ls, respectively. 6. How do I choose electronic components?How to select electronic components?Manufacturers.Application Circuit Complexity.Electrical Parameters [voltage, current, power, accuracy, response time, speed, resolution, etc.]Mechanical Parameters [dimension, package, weight, etc.]Consideration w.r.t Manufacturing / Testing. 7. What is difference between active and passive components?Active components are the elements or devices which are capable of providing or delivering energy to the circuit. Passive components are the ones that do not require any external source for the operation and are capable of storing energy in the form of voltage or current in the circuit. 8. How to Test Electric Components with a Multimeter?Continuity tests measure if electricity can flow through the part.Resistance tests how much current is lost as electricity flows through a component or circuit.The third common test is for voltage, or the force of the electric pressure. 9. What are passive components?A passive component is an electronic component which can only receive energy, which it can either dissipate, absorb or store it in an electric field or a magnetic field. ... Passive components cannot amplify, oscillate, or generate an electrical signal. Common examples of passive components include: Resistors. Inductors. 10. How do I choose a PCB component?6 tips for choosing PCB componentsThink about component footprint decisions.Use good grounding practices.Assign virtual parts footprints.Ensure you have complete BOM Data.Sort reference designators.Check spare gates. Relevant information about "List of Basic Electronic Components"About the article "List of Basic Electronic Components", If you have better ideas, don't hesitate to write your thoughts in the following comment area. You also can find more articles about electronic semiconductor through Google search engine, or refer to the following related articles:Rectifiers and Filters NotesCharacteristics and Functions of DiodesReview and Application of Electronic skinSwitched Mode Power Supply Tutorial: Principles & Functions of SMPS CircuitsTransformers Basics: Construction, Types, Materials and Design
kynix On 2018-07-03
Join our mailing list!
Be the first to know about new products, special offers, and more.
Feature Posts
How Resistors Work: From Basic Principles to Advanced Applications2025-07-30
DC Switching Regulators: Principles, Selection, and Applications2025-05-30
FPGA vs CPLD: In-depth Analysis of Architecture, Performance and Application2025-05-07
MOSFET Technology: Essential Guide to Working Principles & Applications2025-05-04
SMD Resistor: Types, Applications, and Selection Guide2025-04-30