Phone

    00852-6915 1330

ics Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

Resistors

What are the Four Elements in Series and Parallel Circuits?

IntroductionSeries Circuits and Parallel Circuits are main circuit connections, also a third type of circuit involves the dual use of series and parallel connections in a circuit. Circuit connection is a kind of principle for layout diagram that shows the relationship between components drawn by physical and electrical standardized symbols for research and engineering planning. As we all know, there are two types of circuit we can make, called series and parallel. They provide solutions for analyzing performance, installing electronic and electrical products.CatalogIntroductionⅠ Series Circuits and Parallel CircuitsⅡ Series Circuits and Parallel Circuits Calculation2.1 Resistors2.2 Capacitors2.3 Inductor2.4 Switch2.5 Power Supply2.6 Series and Parallel Circuits RulesⅢ Six Circuit Design Software Tools Introduction3.1 Protel PCB Design Platform3.2 Altium Designer3.3 Quartus II3.4 Electronics Workbench (EWB)3.5 NI Multisim3.6 Allegro PCBⅣ Frequently Asked Questions about Series and Parallel CircuitsⅠ Series Circuits and Parallel CircuitsWhat is the difference between series and parallel circuits? Just have a look of the following video and words description about series circuits and parallel circuits to get the basics and differences of them.Series vs Parallel CircuitsSeries connection is one of the basic ways to connect circuit elements. The circuit formed by connecting various electrical parts in series. In the series circuit, the current through each part is equal.Parallel connection is another connection method between electrical components. Components connected in parallel are connected in multiple paths so that the current can split up, and the same voltage is applied to each component.Ⅱ Series Circuits and Parallel Circuits Calculation👉 Resistors in Series and Parallel Circuits2.1 ResistorsResistors in SeriesAs shown in the figure, n resistors connect in series. Now connect the power supply to both ends of this series circuit. According to Kirchhoff’s current law, the current given from the power supply is equal to the current through each resistor, so .According to Ohm’s law, the voltage across the k-th resistor is equal to the current through multiplied by its resistance .According to Kirchhoff’s voltage law, the voltage across the power supply is equal to the algebraic sum of the voltage across all resistors.Therefore, the equivalent resistance Req of n resistors in series is .According to Ohm’s law, the voltage across the power source is equal to the given current times the equivalent resistance .Pay attention to the voltage shared by the resistors of the series circuit is proportional.Conductance G is the reciprocal of resistance R, so the equivalent conductance of n resistors in series is Among them, Gn is the conductance of the n-th resistor.For the simple case of two resistors in series, the equivalent conductance is .Resistors in ParallelWhen linear resistors connect in parallel, the conductance (the reciprocal of resistance) is equal to the sum of the conductances of the parallel resistors, which is called the equivalent conductance, and the reciprocal is called the equivalent resistance. For example, the resistances of R1, R2, and R3, their conductances are G1, G2, and G3, respectively. The total resistance R and total conductance G of the parallel circuit are calculated according to the formula .Note: Calculate the total series and parallel resistance of a circuit using Apogeeweb's Parallel and Series Resistor Calculator. 👉 Capacitors in Series and Parallel Circuits2.2 CapacitorsCapacitors in SeriesAs shown in the figure, n capacitors are connected in series. From the definition of capacitor, it can be obtained that the current passing through the k-th capacitor is equal to its capacitance multiplied by the voltage change rate across it:According to Kirchhoff’s current law, the current i given from the power source (ac or dc) is equal to the current passing through each capacitor, so According to Kirchhoff’s voltage law, the voltage across the power supply is equal to the algebraic sum of the voltage across all capacitors:The voltage change rate of the power supply end is .Therefore, the equivalent capacitance Ceq of n capacitors in series is Each capacitor has a “voltage rating” set by its manufacturer. Assuming that the working voltage exceeds the voltage rating of the capacitor, it may cause capacitor failure. In order to avoid it, several similar capacitors can be connected in series to make the algebraic sum of the voltage rating greater than the operating voltage. However, this will also reduce the equivalent capacitance of the circuit.Capacitors in ParallelAs shown in the figure, n capacitors are connected in parallel. From the definition of capacitor, it can be obtained that the current ik through the k-th capacitor is equal to its capacitance Ck multiplied by the voltage change rate across it:According to Kirchhoff’s voltage law, the voltage across the power supply is equal to the voltage across each capacitor:According to Kirchhoff’s current law, the current given from the power source (dc or ac) is equal to the algebraic sum of the current through each capacitor: Therefore, the equivalent capacitance Ceq of n capacitors in parallel is .Note: Calculate the total series and parallel capacitance of a circuit using Apogeeweb's Series and Parallel Capacitance Calculator. 👉 Inductors in Series and Parallel Circuits2.3 InductorInductor in SeriesAs shown in the figure, n inductors are connected in series. According to the method described above, the equivalent inductance can be calculated as .Among them, Ln is the inductance of the n-th inductor.The magnetic field generated by the inductor will be coupled with the winding coil of the adjacent inductor. So it is difficult to avoid the mutual influence of the adjacent inductors. The mutual inductance M of physical quantities can give a measure of this influence.A series circuit composed of two inductors L1 and L2, and the mutual inductance Ms.1) Assuming that the magnetic fields or fluxes generated by two inductors are in the same direction, the equivalent mutual inductance Leq is expressed by the equation: 2) Assuming that the magnetic fields or fluxes generated by two inductors are in opposite directions, Leq is expressed by the equation:For a parallel circuit with three or more inductors, it is necessary to consider the self-inductance of each inductor and the mutual inductance among the inductors, which makes the calculation more complicated. The equivalent inductance is the algebraic sum of all self-inductance and mutual inductance.For example, a series circuit composed of three inductors will involve three self-inductances and six mutual inductances. The self-inductances of the three inductors are M11, M22, and M33, and the mutual inductances are M12, M13, M21, M23, M31, and M32.Equivalent inductance is .Since the mutual inductance between any two inductors is equal to each other, the latter two sets of mutual inductance can be combined:Inductors in ParallelN ideal inductors without mutual inductance are connected in parallel. Similar to the method described above, the equivalent inductance Leq can be calculated as .Among them, Li is the inductance of the i-th inductor.The above equation describes an ideal case where n inductors are connected in parallel without mutual inductance.A parallel circuit composed of two inductors with inductances L1 and L2 and mutual inductance M:1) Assuming that the magnetic fields or fluxes generated by two inductors are in the same direction, the equivalent mutual inductance Leq is expressed by the equation: 2) Assuming that the magnetic fields or fluxes generated by two inductors are in opposite directions, Leq is expressed by the equation:For a parallel circuit with three or more inductors, it is necessary to consider the self-inductance of each inductor and the mutual inductance among the inductors, which makes the calculation more complicated. 👉 Switch in Series and Parallel Circuits2.4 SwitchSwitch in SeriesTwo or more switches are connected in series to form an or gate circuit. Assuming a power supply is connected to both ends of the circuit, current will only flow when all switches are closed.Switch in ParallelTwo or more switches are connected in parallel to form an or gate circuit. Assuming that a power supply is connected to both ends of this circuit, even though any one of the switches is closed, current will flow. 👉 Power Supply in Series and Parallel Circuits2.5 Power SupplyPower Supply in SeriesFor example, assuming that several cells in the battery pack are connected in series to form a power source, the voltage across the power source is the algebraic sum of the voltages across all cells.Power Supply in ParallelFor example, assuming that a battery pack uses several single batteries with the same voltage connected in parallel as a power source, the voltage across the power source is equal to the voltage across the single battery.Note: Get more info from Switching Power Supply Circuit Diagram with Explanation. 2.6 Series and Parallel Circuits RulesHow to judge whether the electrical circuits are connected in series or in parallel? Series and parallel are the two most basic forms of circuit connection, and there are certain differences between them. So get to know their basic characteristics well according to the following specific methods.(1) Visual CheckLook at the connection form of electrical parts in the circuit. The one by one in sequence is series; the one paralleled between two points of the circuit is parallel.(2) Current FlowWhen the current flowing from the positive pole of the power supply to each element in turn shows that the circuit is in series; when the current flows to two branches and get together at a certain place finally, it indicates that the circuit is in parallel.(3) Removing ComponentsRemove one electrical part at will to see whether other electrical components are working normally. If the circuit can continue to work, then the connection relationship of this circuit is in parallel, otherwise, it is in series. Ⅲ Six Circuit Design Software Tools Introduction3.1 Protel PCB Design PlatformProtel PCB is a CAD software for the circuit industry launched by Protel Systems Pty Ltd in 1985, and has rebranded to Altium Designer. It has many advantages compared with many EDA software for circuit designers. Almost all circuit companies use it. The early Protel PCB was mainly used as a printed board automatic wiring tool. It ran in DOS and had fewer hardware requirements. It can run under the 1M memory of a 286 machine without a hard disk. However, it’s less functional, only electrical schematic drawing and printed board design functions, and the PCB layout rate of automatic wiring is also low.It is a professional circuit board drawing tool. It includes electrical schematic drawing, analog circuit and digital circuit mixed signal simulation, multilayer PCB design, programmable logic device design, chart generation, circuit table generation, and supports macro operations, etc. And it has a client/server architecture. PROTEL is also compatible with some other design software file formats, such as ORCAD, PSPICE, EXCEL, etc. Using automatic routing of multi-layer can achieve 100% layout rate of high-density PCBs.3.2 Altium DesignerAltium Designer is one of the most popular of the high end PCB design software packages on the market today. It provides a single, unified application that incorporates all the technologies and capabilities necessary for complete electronic products, which mainly runs on the Windows operating system. This software provides designers with brand-new design solutions through the perfect integration of schematic design, circuit simulation, PCB drawing editing, topology logic automatic routing, signal integrity analysis and design output, etc. When using this software, the quality and efficiency of circuit design can be greatly improved.Fully inheriting the functions and advantages of the previous series of versions of Protel 99SE and Protel DXP, Altium Designer has many improvements and many high-end features. The platform broadens the traditional interface of board-level design and fully integrates FPGA design functions and SOPC design implementation functions, allowing engineers to integrate FPGA in system design with PCB design and embedded design. With these advantages, Altium Designer requires higher computer system performance than the previous version. 3.3 Quartus IIThe Altera Quartus II design software is a multiplatform design environment that easily adapts to your specific needs in all phases of FPGA and CPLD design. In other words, Quartus II software delivers the highest productivity and performance for Altera FPGAs, CPLDs, and HardCopy ASICs. It is a comprehensive CPLD/FPGA development software, and supports schematics, VHDL, VerilogHDL and AHDL (Altera Hardware supports Description Language) and other design input forms. Quartus II embedded with its own synthesizer and simulator, can complete the process of design input to the hardware configuration. It can run in Windows, Linux and Unix. Use Tcl scripts to complete the design process, and it also provides a complete user graphical interface design method. Quartus II has the characteristics of fast running speed, unified interface, centralized function, easy to learn and easy to use.Quartus II provides a fully integrated development which independent of circuit structure, with all the features of digital logic design, including:1. You can use the schematic diagram, structural block diagram, VerilogHDL, AHDL and VHDL to complete the circuit description, and save it as a design entity file.2. Chip (circuit) plane layout wiring editing3. With LogicLock region, users can build and optimize the system, and add subsequent modules that have little or no impact on the performance of the original system.4. Powerful logic synthesis tool5. Complete circuit function simulation and sequential logic simulation6. Timing analysis and critical path delay analysis7. Signaltap ii logic analyzer can be used for embedded logic analysis.8. Support the addition and creation of software source files, and link them to generate programming files.9. Use the combined compilation method to complete the overall design process at one time.10. Automatically locate compilation errors.11. Efficient period programming and verification12. Read into standard EDIF, VHDL and Verilog netlist files.13. It can generate VHDL and Verilog netlist files used by third-party EDA software.3.4 Electronics Workbench (EWB)EWB is is a mixed-mode SPICE-based electronics design and simulation tool, launched by Interactive Image Technology Co., Ltd. in the early 1990s. It is used for mixed simulation of analog circuits and digital circuits. With this powerful software, you can directly see the output of various circuits on the screen.Compared with other EDA software, EWB is a smaller software, and its function is relatively single. However. its simulation function is very powerful, almost 100% simulation results of real circuits. It provides parts such as multimeters, oscilloscopes, signal generators, frequency sweepers, logic analyzers, digital signal generators, logic converters, etc., and its device library contains many transistor components, integrated circuits and digital gate circuit chips from large companies.  In addition, components that are not in the device library can also be imported externally. Among many circuit simulation software, EWB is the easiest to use. Its working interface is very intuitive. The schematic diagram and various tools are in the same window. People who have never touched it can use the software proficiently with a short-time learning. For electronic designers, it is an excellent EDA tool. For many circuits, you can know its results without using a soldering iron. If you want to change components or change parameters, you only need to click the mouse. It can also be used as an auxiliary teaching software for electrical knowledge.3.5 NI MultisimMultisim is a Windows-based simulation tool launched by National Instruments (NI) Co., Ltd.. It is industry standard SPICE simulation and circuit design software for analog, digital, and power electronics in education and research. It includes graphical input of circuit schematics, circuit hardware description language input, and has rich simulation analysis capabilities. Engineers can use it to interactively build circuit schematics and simulate the circuit.With SPICE simulation, designers can quickly capture, simulate and analyze new designs without knowing SPICE deeply, which also makes it more suitable for electronics education. Through Multisim and virtual instrument technology, PCB designers and electronics educators can complete a complete integrated design process from theory to schematic capture and simulation to prototype design and testing.NI Multisim software is an EDA tool software specially used for electronic circuit simulation and design. As a personal desktop electronic design tool running in Windows, NI Multisim is a complete integrated design environment. Its computer simulation and virtual instrument technology can solve the problem of disconnection between theoretical teaching and actual reality experiment. Students can easily reproduce the theoretical knowledge they have learned through computer simulation, and can use virtual instrument technology to create their own instruments. It has an intuitive graphical interface, abundant components, powerful simulation capabilities, abundant testing instruments and complete analysis methods. NI Multisim software is a not bad teaching tool.3.6 Allegro PCBAllegro PCB is an advanced PCB design routing tool introduced by Cadence. It provides a good and interactive working interface, and powerful and complete functions. Provide the most perfect solution for the current high-speed, high-density, multi-layer complex PCB design and wiring, with the combination of its front-end products Cadence, OrCAD, and Capture. Allegro has a complete constraint setting. Users only need to set the wiring rules as required. The wiring design requirements can be met without violating DRC, thus saving tedious manual inspection time and improving work efficiency. It can also define parameters such as minimum line width or line length to meet the various requirements of today's high-speed circuit board wiring. Allegro PCB enables you to do high-speed design, RF antenna, flex-circuitry, and design for manufacturing (DFM) technology.For the drawing and modification functions of copper foil that the industry attaches great importance to, Allegro provides a simple and convenient inner layer division function, as well as the ability to review the inner layer of the positive and negative film. For copper paving, it can also be divided into dynamic copper or static copper, which can be used for different applications. Dynamic copper parameters can be divided into different levels of settings for all copper, single copper or single object, so as to meet the requirements of different connection effects or spacing values to match the special settings due to design requirements. Ⅳ Frequently Asked Questions about Series and Parallel Circuits1. What is the difference between parallel and series circuits?In a parallel circuit, the voltage across each of the components is the same, and the total current is the sum of the currents flowing through each component. ... In a series circuit, every device must function for the circuit to be complete. If one bulb burns out in a series circuit, the entire circuit is broken. 2. What are the rules for series and parallel circuits?Rules regarding Series and Parallel CircuitsVoltage drops add to equal total voltage.All components share the same (equal) current.Resistances add to equal total resistance. 3. What are the similarities and differences between series and parallel circuits?Series circuits are designed so that the current through each component is the same, whereas parallel circuits are designed so that the voltage through each component is the same. 4. Why is resistance different in series and parallel?In a series circuit, the output current of the first resistor flows into the input of the second resistor; therefore, the current is the same in each resistor. In a parallel circuit, all of the resistor leads on one side of the resistors are connected together and all the leads on the other side are connected together. 5. Which software is best for circuit design?Based on Proto-Electronics client preferences, we have drawn up the top 10 best electronics CAD software programmes.EagleAltiumProteusKiCadCadence OrCAD PCB DesignerDesignSparkProtelCadstar
kynix On 2021-01-05   6075
Resistors

How Do You Use a Multimeter? Guide for Beginners

Introduction: A Comprehensive Guide to Using a Multimeter in 2025When it comes to measuring instruments, the question often arises: how do you use a multimeter effectively? A Multimeter, also known as a VOM (volt-ohm-milliammeter) or DMM (Digital Multimeter), is the indispensable "Swiss Army Knife" for electronics. It is used to measure two or more electrical values—principally voltage (volts), current (amps), and resistance (ohms) in electronic and electrical circuits.In 2025, modern multimeters have evolved significantly. Beyond basic measurements, many now include features like capacitance testing, transistor checks, temperature sensing, and even Bluetooth connectivity for smartphone data logging. Whether you are troubleshooting a smart home device, checking automotive wiring, or testing a battery, the multimeter is your primary diagnostic tool.Multimeters are generally divided into two types: analog multimeters and digital multimeters (DMM). While analog meters use a moving needle, digital versions are now the industry standard, offering high accuracy, auto-ranging capabilities, and easy-to-read LCD or OLED displays. This guide is designed for beginners and will cover the basic parts, working principles, functions, and safety tips for using a multimeter in the modern era.Ⅰ What are the Parts of a Multimeter?The anatomy of a multitester generally includes a display (scale or screen), a selection knob, ports (jacks), and test probes. However, the interface differs between the older analog style and modern digital tools.Analog Multimeters: Use a microammeter with a moving pointer (needle) to display readings against a printed scale. They require the user to interpret the scale based on the selected range.Digital Multimeters (DMM): The current mainstream choice. They feature a numeric digital display, often with a backlight for dark environments. Modern DMMs may also include "True RMS" for accurate AC readings and auto-ranging features that automatically select the correct measurement scale for you.A common digital multimeter is composed of three main interface parts:1.1 The Display (Meter Head)On a digital multimeter, this is the LCD or LED screen where measurement values are shown. It often displays icons for battery life, high voltage warnings, and the unit of measurement (e.g., V, A, Ω). High-end models in 2025 may feature high-resolution color screens or bar graphs that mimic analog needles to show fluctuating signals.1.2 Measuring Circuit (Internal)Hidden inside the case, the measuring circuit converts incoming analog signals (voltage, current, resistance) into digital data. It is composed of precision resistors, an Analog-to-Digital (A/D) converter, and protective fuses to ensure safety during overload.1.3 Rotary SwitchThe central dial allows you to select the function (Volts, Amps, Ohms) and the range. In Auto-ranging multimeters, you simply select the function (e.g., DC Voltage), and the meter automatically adjusts to the scale of the signal. In Manual-ranging meters, you must select the specific range (e.g., 20V, 200V) yourself.Ⅱ Working Principle of MultimeterA Digital Multimeter (DMM) works by converting an analog input signal into a digital value using an A/D converter. The core logic involves comparing the input voltage against a reference voltage.To measure current and resistance, the multimeter actually uses voltage as the base reference:Current: The meter measures the voltage drop across a known internal shunt resistor.Resistance: The meter outputs a small, known current through the component being tested and measures the resulting voltage to calculate resistance (Ohm's Law).Modern DMMs use complex logic control circuits to manage the display, auto-ranging, and safety checks, ensuring that the reading on the screen is stable and accurate. Ⅲ Multimeter Operating ProceduresTo ensure accuracy and safety—especially with modern high-energy circuits—follow these steps:Safety Check: Inspect your test leads for damaged insulation. Ensure the multimeter is rated for the voltage you are testing (e.g., CAT III or CAT IV ratings for household mains).Select Function: Turn the rotary dial to the correct setting (Voltage, Current, or Resistance) before connecting the probes.Select Range: If using a manual-ranging meter and the value is unknown, always start at the maximum range and switch down to lower ranges to get a precise reading. Auto-ranging meters handle this automatically.Zero Calibration: For resistance measurements on analog meters, touch the probes together and zero the needle. Digital meters usually auto-zero, but you can check the "Rel" (Relative) mode on advanced models to null out lead resistance.Power Off for Resistance: Never measure resistance or continuity on a live circuit. Turn off the power to the device before testing.Probe Handling: Keep your fingers behind the finger guards on the test probes to avoid electric shock.Ⅳ Common Multimeter FunctionsMeasure Resistance (Ohms - Ω)Ensure the circuit power is OFF. Connect the test leads across the component (resistor, coil, etc.). Note: Measuring a component while it is soldered to a PCB may give inaccurate results due to parallel paths from other components.Measure Current (Amps - A/mA)Critical Step: You must physically move the red probe to the specific "Amps" or "mA" jack on the multimeter. The meter must be connected in series with the circuit (you must break the circuit and let current flow through the meter). Warning: Connecting a meter in current mode across a voltage source (parallel) will blow the meter's fuse.Measure Voltage (Volts - V)Connect the meter in parallel (across the component or power source). Ensure you select AC (V~) for wall outlets or DC (V=) for batteries.Detect Short Circuit (Continuity)Set the dial to the continuity mode (often marked with a sound wave symbol). Touch probes to two points. If resistance is near zero (a short), the multimeter will beep. This is excellent for checking broken wires or fuses.Non-Contact Voltage (NCV)Many modern multimeters (2020s era and later) include an NCV sensor at the tip. This allows you to detect the presence of live AC voltage in a wire or outlet without touching the metal contacts.Test ICs and ComponentsWhile multimeters can check supply voltage (VCC) and ground pins on Integrated Circuits (ICs), troubleshooting internal IC logic is often better done with an oscilloscope or logic analyzer. However, a multimeter is perfect for finding shorted pins. Ⅴ Multimeter Usage Tips1. Probe Safety: Never touch the metal tips of the probes during a test. Always hold the insulated handles behind the finger guards.2. Switching Gears: Never rotate the selection dial while the probes are connected to a live high-voltage circuit. This can cause internal arcing. Disconnect probes, switch modes, then reconnect.3. Battery Maintenance: If the multimeter will not be used for a long period, remove the internal battery to prevent leakage and corrosion.4. High Voltage Awareness: Be aware of the "CAT" rating of your meter. Do not use a CAT II meter for main service panels (which require CAT III or CAT IV ratings).Video: How to Use a Multimeter?Ⅵ How to Find Circuit Faults with Multimeter6.1 General Troubleshooting Strategy1. Visual InspectionBefore measuring, look for charred components, swollen capacitors, or loose wires. Touching components (cautiously) to check for overheating can also identify shorts.2. Voltage TracingMeasure the voltage at various points in the circuit starting from the power source. If voltage is present at point A but missing at point B, the fault lies between them (e.g., a broken trace or failed component).3. Hidden TroubleshootingIntermittent failures are often caused by "cold" solder joints or loose connectors. Continuity mode is vital here. Wiggle wires while testing continuity; if the beep stops, you have found a loose connection. 6.2 Measuring Techniques6.2.1 Voltage Measuring PointsTesting voltage against a "Ground" reference is the standard method. Connect the black probe to the circuit Ground (GND) and use the red probe to touch various test points (VCC, output pins). Deviations from the expected voltage (e.g., getting 2V on a 5V line) usually indicate a problem.6.2.2 Measuring Parameters Selection① Always check if you are measuring AC or DC. Measuring AC voltage while in DC mode (or vice versa) will give false readings.② For signal circuits, remember that standard multimeters measure "Average" or "RMS" voltage. They may not accurately show fast data pulses—an oscilloscope is required for that.③ Polarity: In DC mode, if you reverse the probes (Red on negative, Black on positive), the screen will simply show a negative sign (e.g., -12V). This is normal and safe for digital meters. Ⅶ How to Measure Current with Digital MultimeterMeasuring DC Current1. Insert the Red test lead into the jack marked "mA" (for low current) or "10A/20A" (for high current). Insert the Black lead into "COM".2. Turn the dial to the DC Current setting (A=).3. Break the circuit: You must physically interrupt the wire and place the multimeter probes in line with the circuit so current flows through the meter.4. Power on the circuit and read the value.Figure 1. Measuring Operating Current of a DC Relay If the reading is negative, your probes are reversed (current is entering the black probe). This does not damage a digital meter.Figure 2. Measuring DC Current in Series Measuring Current with an Analog MultimeterWith analog meters, polarity matters. If you connect probes backward, the needle will deflect to the left (below zero), potentially damaging the mechanism. Always ensure Red connects to the more positive side and Black to the negative side.Figure 3. Series connection with Analog Multimeter Figure 4. Reading the Scale on an Analog Multimeter Measuring AC CurrentThe process is similar to DC, but you must select the AC Current setting (A~). For high currents (e.g., household mains), it is highly recommended to use a Clamp Meter instead of a standard multimeter for safety. A clamp meter measures current via magnetic fields without breaking the circuit.Figure 5. AC Measurement Diagram Ⅷ Which is Better: Analog or Digital Multimeter?For 99% of users in 2025, the Digital Multimeter (DMM) is superior. It offers higher accuracy, higher input impedance (which means it doesn't affect the circuit you are testing), and easier readability. Analog meters are now a niche tool, primarily used by technicians who need to see real-time trends or rapid fluctuations that a digital digital might miss (though modern DMMs with "bar graphs" solve this).Analog MultimeterDigital MultimeterVisualizes trends/fluctuations easily via needle movement.Easy to read exact numbers; no parallax errors.Lower input impedance (can load down sensitive circuits).High input impedance (better for delicate electronics).Susceptible to damage from physical shock (drops).generally more rugged and durable.Often requires manual zeroing and range selection.Includes Auto-ranging, Auto-polarity, and specialized functions.Both meters have their place, but if you can only afford one, buy a Digital Multimeter. They are now available at very affordable price points without sacrificing essential accuracy. Ⅸ Best Multimeter Brands in 2025When selecting a multimeter, reliability and safety are paramount. Brands differ by their target audience: Professionals (industrial use) vs. Hobbyists (home use). Below are reputable brands recognized in the industry today.*Etekcity (Budget/Home)Mastech GroupInnova (Automotive)Klein ToolsKeysight Technologies (formerly Agilent)BrymenKaiweets / AstroAI (Budget)Fluke (Professional Gold Standard)ExtechAmprobeHioki Ⅹ Frequently Asked Questions1. What is a multimeter primarily used for?A digital multimeter is a diagnostic tool used to measure electrical values—principally voltage (Volts), current (Amps), and resistance (Ohms). It is standard equipment for electricians, automotive mechanics, and HVAC technicians. 2. What is "Auto-Ranging"?Auto-ranging is a feature on digital multimeters where the meter automatically selects the correct measurement range for the signal it detects. You simply select "Voltage," and the meter decides if it's millivolts or hundreds of volts. This saves time and prevents setup errors. 3. Why is "True RMS" important?True RMS (Root Mean Square) allows a multimeter to accurately measure AC voltage even when the sine wave is distorted (common in motor drives, HVAC systems, and computers). Non-True RMS meters are only accurate on perfect sine waves. 4. Can I use a multimeter to test a battery?Yes. Set the multimeter to DC Voltage (V=). Connect the red probe to the positive (+) terminal and black to negative (-). A fully charged 1.5V AA battery should read greater than 1.5V (usually 1.6V). If it reads below 1.2V, it is dead. 5. What are CAT ratings?CAT ratings (Category I, II, III, IV) define the safety level of the meter. CAT III or CAT IV is recommended for testing household wiring and mains power to protect against dangerous transient voltage spikes.
Kynix On 2020-12-19   4358
Resistors

What is Clipper Circuit and Its Types?

IntroductionIn electronics, what is clipper? A circuit which removes the peak of a waveform is known as a clipper. Clipper circuit is designed to prevent a signal from exceeding a predetermined reference voltage level. The clipper circuit can be designed by utilizing both the linear and nonlinear elements such as resistors, diodes, or transistors. The diode clipper, also known as a diode limiter, is a wave shaping circuit that limits positive or negative amplitude, or both. In electronics, diode clipper circuits are commonly used to process various signals. It is is a circuit designed to prevent a signal from exceeding a predetermined reference voltage level. Clipping changes the shape of the waveform and alters its spectral components.Clipper Circuits IntroductionCatalogIntroductionⅠ Clipper Circuit Types1.1 Positive Clipper Circuit1.2 Negative Clipper Circuit1.3 Combinational Limiter CircuitⅡ Clipper Circuits Analysis2.1 Clipper Circuit Structure2.2 Clipper Circuit ProblemsⅢ General Forms of Clipper Circuits3.1 Clipper Circuit Description3.2 Common Clipper Circuit ExamplesⅠ Clipper Circuit TypesDiode clipper is a limiting circuit which limits the output voltage. In electronics, a clipper is a circuit designed to prevent a signal from exceeding a predetermined reference voltage level. A basic diode limiter circuit is composed of a diode and a resistor. It is divided into three types: positive clipper circuit, negative clipper circuit and combinational clipper circuit. The positive clipper circuit produces a clipping effect when the input voltage is higher than a certain upper limit value; the negative clipper circuit produces a limit effect when the input voltage is lower than a certain lower limit value; the combinational clipper circuit produces a limit effect when the input voltage is too high or too low. In a positive clipper, the positive half cycles of the input voltage will be removed. During the negative half cycle of the input, the diode is forward biased and so the negative half cycle appears across the output. The clipper circuits are described as following.1.1 Positive Clipper CircuitThe diode in clipper circuit is connected in series to the input signal and that attenuates the positive portions of the waveform. The positive clamping circuit blocks the input signal when the diode is forward biased. During the negative half cycle of an AC signal, the diode is forward biased and allows electric current through it. In following figure, when the input signal voltage is lower than a preset upper limit voltage, the output voltage will change with the input voltage, however, when the input voltage reaches or exceeds the upper limit, the output voltage will remain at a fixed value, so that the signal amplitude is limited at the output.1.2 Negative Clipper CircuitThe diode in clipper circuit is connected in series to the input signal and that attenuates the negative portions of the waveform, is termed as negative series clipper. For the figure below, the diode is series to the input and output. If the diode has ideal switching characteristics, when iu is lower than E, D will not conduct, ou=E; when ui is higher than E, D will conduct, ou=iu. The limiting characteristic of this limiter circuit is shown in the figure.1.3 Combinational Limiter CircuitThis kind of circuit combines the positive and negative limiters together which shows in the following figure. Ⅱ Clipper Circuits Analysis2.1 Clipper Circuit StructureIn the circuit, Al is an integrated circuit (a common component), VT1 and VT2 are transistors, Rl and R2 are resistors, and VDl to VD6 are diodes.Analyzing the effect of VD1 and VD2 in the circuit mainly explains the following points.1) It can be seen from the circuit that the circuit structure of the two groups of diodes are the same. Both play the same role in this circuit, so the working principle of them are the same.2) The pin ① is connected to the base of the transistor VT1 through a resistor Rl. Obviously Rl is a signal transmission resistor. The signal output on the pin ① is added to the base of VT1 through Rl (there is no DC blocking capacitor between pin ① and VT1). From this circuit structure, it can be judged that the pin ① is an output signal pin, and it outputs a composite signal of DC and AC. The purpose of determining that the pin ① is to figure out the specific function of the diode VD1 in the circuit.3) The DC voltage output by pin ① is not high enough to make the external diode in a conducting state. The analysis is: if the DC voltage output by the pin ① is high enough, then VD1, VD2 and VD3 conduct, and the internal resistance becomes small. This will shunt the AC signal output by the pin ① to the ground, so the signal will be attenuated. However, this circuit does not need such attenuation. Therefore, the conclusion drawn from this: VD1, VD2 and VD3 are not turned on by pin ① DC voltage output.4) The output from pin ① is the superimposed signal of DC and AC, which is added to the base of the transistor VT1 through the resistor Rl. VT1 is an NPN transistor. If the amplitude of the positive half-cycle AC signal added to the base of VT1 is very large, which may burn the VT1. When the negative half-cycle signal added to the base of VT1 is large, which has no effect on VT1, because the negative signal on the base of VT1 reduces current.Follow the above circuit analysis, it can be judged that VD1, VD2, and VD3 in the circuit has clipper function, to prevent VT1 from burning out. 2.2 Clipper Circuit ProblemsIn the figure, Ul is the DC voltage in the output of pin ①, U2 is the limiting voltage value.When the AC voltage in the output signal of pin ① is relatively small, the positive half cycle of the AC signal plus the DC output voltage does not make the VD1, VD2 and VD3 conduction. Therefore, all diodes are cut off, which has no effect on the AC signal output by pin ①. Assuming that the positive half-cycle output AC signal by pin ① is very large during a certain period, as shown in the signal waveform, at this time it plus the DC voltage can conduct VD1, VD2 and VD3. If the conduction voltage of each diode is 0.7V, then three diodes is 2.1V. Since the tube voltage drop after conduction is basically the same, that is, the maximum voltage of pin ① is 2.1V. So the excess part of the positive half cycle of the AC signal is limited by the resistor. When the DC and AC output signals at pin ① is less than 2.1V, diodes will not conduct and keep cutoff state, which has no clipping effect on the signal.For the specific details of clipper circuit, there are several explanations as follows.1) The negative half cycle large signal output by the pin ④ will not cause VT1 overcurrent, because it will decrease the base voltage of the NPN transistor and the base current, so there is no need to add the limiter circuit.2) The one-way limiter circuit mentioned above, it can only limit the large signal part of the positive or negative half of the signal, and does not limit the signal in the other half. The other is the combinational limiter circuit, which can limit the positive and negative half-cycle signals at the same time.3) There are many reasons for the abnormal increase of the signal amplitude. For example, the fluctuation of the power supply voltage cause it to increase a lot at a certain moment, and the large-scale interference pulse from the outside into the circuit also causes a certain increase.4) After the three diodes VD1, VD2 and VD3 conduct, the sum of the DC and AC voltages on pin ① is 2.1V. This voltage added to the base of VT1 through resistor Rl is maximum, so as to the current of VT1.5) Since the pin ① is the same as the external circuit of pin ②, the working principle of the limiter circuit is the same. So only one circuit needs to be analyzed when analyzing the circuit.6) According to the characteristics of the series circuit, the current in the series circuit is equal everywhere. It can be known that the three series diodes VD1, VD2 and VD3 are turned on at the same time, or they will be turned off at the same time. Therefore, in the series circuit, a diode is turned on and other diodes are turned on.Ⅲ General Forms of Clipper Circuits3.1 Clipper Circuit DescriptionThere are two types of clippers namely series and parallel. In series clipper, diode is connected in series with the load. In parallel clipper, diode is in parallel to the load.1) Series clippers: if the diode is connected in series with load resistanceUnbiased series clipper: in that case the circuit diode is connected in series with load resistance and no external voltage is applied to the circuit.+ve unbiased series clipper: if the +ve portion of output is clipped its called +ve unbiased series clipper.-ve unbiased series clipper: if the -ve portion of output is clipped its called +ve unbiased series clipper.Biased series clipper: if in the circuit, diode is connected in series with load resistance and external voltage is applied to the circuit+ve biased series clipper: if the +ve portion of output is clipped its called +ve biased series clipper.-ve biased series clipper: if the -ve portion of output is clipped its called +ve biased series clipper.2) Parallel clippers: if the diode is connected in parallel with load resistanceUnbiased parallel clipper: in that case the circuit diode is connected in parallel with load resistance and no external voltage is applied to the circuit.+ve unbiased parallel clipper: if the +ve portion of output is clipped its called +ve unbiased parallel clipper.-ve unbiased parallel clipper: if the -ve portion of output is clipped its called +ve unbiased parallel clipper.Biased parallel clipper: if in the circuit, diode is connected in parallel with load resistance and external voltage is applied to the circuit+ve unbiased parallel clipper: if the +ve portion of output is clipped its called +ve biased series clipper.-ve unbiased parallel clipper: if the -ve portion of output is clipped its called +ve biased series clipper. 3.2 Common Clipper Circuit ExamplesIn general, clippers circuit are classified into two types: Series Clippers, Shunt Clippers, and Dual (Combination) Clippers.Series Clipper: The diode is connected in series with the load resistance. 👇Figure 1. Series Positive ClipperThe positive amplitude waveform is cut, and the negative amplitude waveform is retained, as follows:Figure 2. Series Positive Clipper with Positive BiasThe positive amplitude waveform is cut, and the offset positive voltage is retained on the negative amplitude waveform, as follows:Figure 3. Series Positive Clipper with Negative BiasThe waveform of positive amplitude is cut, and the negative voltage is shifted based on the waveform of negative amplitude, as follows:Figure 4. Series Negative ClipperThe negative amplitude waveform is cut, and the positive amplitude waveform is retained, as follows:Figure 5. Series Negative Clipper with Positive BiasThe negative amplitude waveform is cut, and the positive voltage is offset on the positive amplitude waveform, as follows:Figure 6. Series Negative Clipper with Negative BiasThe negative amplitude waveform is cut, and the negative voltage is offset on the positive amplitude waveform as follows: Shunt Clipper: Diode is in parallel with load resistance in circuit. 👇Figure 7. Shunt Positive ClipperFigure 8. Shunt Positive Clipper with Positive BiasFigure 9. Shunt Positive Clipper with Negative BiasFigure 10. Shunt Negative ClipperFigure 11. Shunt Negative Clipper with Positive BiasFigure 12. Shunt Negative Clipper with Negative Bias Dual (Combination) Clipper: It is desired to remove a small portion of both positive and negative half cycles. 👇Figure 13. Combination ClipperWhen the positive and negative waveforms must be limited, a combinational limiter circuit is required, as follows:Images Reference: Clipper Circuits - Series Clipper, Shunt Clipper, and Dual Clipper Frequently Asked Questions about Diode Limiter and Clipper Circuit1. What is Clipper and clamper?The major difference between clipper and clamper is that clipper is a limiting circuit which limits the output voltage while clamper is a circuit which shifts the DC level of output voltage. ... While clamper is used when we need multiples of the input voltage at the output terminal. 2. What is the function of clipper circuit?In electronics, a clipper is a circuit designed to prevent a signal from exceeding a predetermined reference voltage level. A clipper does not distort the remaining part of the applied waveform. 3. What is Clipper circuit and its types?A clipper is a device which limits, remove or prevents some portion of the wave form (input signal voltage) above or below a certain level, in other words, the circuit which limits positive or negative amplitude ,or both is called chipping circuit. The clipper circuits are of the following types. Series positive clipper. 4. What is the difference between a positive clipper and a negative Clipper?Positive Clipper and Negative Clipper. In a positive clipper, the positive half cycles of the input voltage will be removed. ... During the negative half cycle of the input, the diode is forward biased and so the negative half cycle appears across the output. 5. How does diode clipping work?The Diode Clipper, also known as a Diode Limiter, is a wave shaping circuit that takes an input waveform and clips or cuts off its top half, bottom half or both halves together. This clipping of the input signal produces an output waveform that resembles a flattened version of the input. 6. What is the main purpose of a diode limiter?The diode limiter also called Clipper as it is used to limit the input voltage. A basic diode limiter circuit is composed of a diode and a resistor. Depending upon the circuit configuration and bias, the circuit may clip or eliminate all or part of an input waveform. It limits the output voltage to a specific value. 7. What is the purpose of a clamping diode?The clamping circuit fixes the voltage lower limit to zero, that is, the start of the signal is 0 V. The positive clamping circuit blocks the input signal when the diode is forward biased. During the negative half cycle of an AC signal, the diode is forward biased and allows electric current through it. 8. What is a diode clamping circuit?A clamper circuit shifts the DC level or the reference level of the signal to the desired level without changing the shape of the waveform. The clamper circuit can be designed using the diode, resistor, and the capacitor.
kynix On 2020-12-02   19897
Resistors

In-Memory Computing Technology Overview

IntroductionIn-memory computing (IMC), a technique of future computing, stores data in RAM to run calculations entirely in computer memory. With the rise of the big data era, faster data processing capabilities are required. Computer memory and storage space are also growing exponentially to adapt to large-capacity data collection and complex data analysis, which promotes the development of AI (artificial intelligence), and then derives emerging stuff, that is, in-memory computing.In-memory Computing (IMC) ExplainedCatalogIntroductionⅠ Memory Wall: Processor /Memory Performance GapⅡ Developing RequirementⅢ What Is In-memory Computing?3.1 In-memory Computing Definition3.2 Four Realization MethodsⅣ Driving Force of In-memory Computing and Market Prospects4.1 In-memory Computing for AI4.2 In-memory Computing Product Outlook4.3 In-memory Computing Market and ProspectⅤ ConclusionⅠ Memory Wall: Processor / Memory Performance GapThe von Neumann architecture has occupied the dominant position in computer system when the computer invented. This kind of calculation method is to store the data in the main memory first, and then fetch the instructions from the main memory to execute them in order when running. We all know that if the connecting speed of the memory cannot keep up with the performance of the CPU, the computing will be limited. This is a memory wall. At the same time, in terms of efficiency, the von Neumann architecture also has obvious shortcomings. It consumes more energy to read and write data than to calculate once time.Figure 1. Von Neumann Architecture DiagramThe performance of computer processors has developed rapidly based on Moore's Law, and has been directly improved with the invention of transistors. The main memory of the computer uses the DRAM. It is a high-density storage solution based on capacitor charging and discharging. Its performance (speed) depends on two aspects, namely the reading/writing speed of the capacitor charging and discharging in the memory and the interface bandwidth between the devices. The read/write speed of capacitor charging and discharging has increased with Moore’s Law, but the speed is not as fast as the processor. In addition, the interface between DRAM and the processor is a mixed-signal circuit, and its bandwidth increasing speed is mainly restricted by the signal integrity of the traces on the PCB. This has also caused the performance improvement of DRAM to be much slower than that of the processor. At present, the performance of DRAM has become an huge bottleneck of overall computer performance, the so-called "memory wall".  It blocks the computing performance improvement.Figure 2. Moore's Law Effect Ⅱ Developing RequirementIn the current AI technology, with the increasing amount of data and calculations, the original von Neumann architecture is facing more and more challenges. Rely on expanding CPU, the hardware architecture can’t have a large amount of calculation. Also the larger storage capacity is heavily rely on the past architecture, it is also very unsuitable for AI. When the memory capacity is large to a certain extent, it can only show that certain technologies need innovation. In order to solve the "memory wall" problem, future computers are not based on computing memory, but the in-memory computing, thereby reducing the cost of data access in the calculation process.Figure 3. Conventional Computing vs In-memory Computing Ⅲ What Is In-memory Computing?3.1 In-memory Computing DefinitionIn-memory computing (or in-memory computation) is a technique based on RAM data storage and indexing, which proposed by the MIT research group, and its main purpose is to accelerate the convolution calculation. We know that convolution calculations can be expanded into weighted accumulation calculations. From another perspective, it is actually a weighted average of multiple numbers. Therefore, the circuit realizes the weighted average of the charge domain. The weight (1-bit) is stored in SRAM, and the input data (7-bit digital signal) becomes an analog signal through the DAC. According to the corresponding weight in the SRAM, the output is multiplied by 1 or -1 in the analog domain, which averaged in the analog domain, and finally read out by the ADC as a digital signal. Specifically, since the weight of the multiplication is 1-bit (1 or -1), it can be controlled by using a switch and a differential line simply. If the weight is 1, the capacitor on the side of the differential line is charged to the required output value. Otherwise, let the other side of the differential line be charged to this value. As for average, connect several differential lines together in the charge domain.Of course, there is more than one circuit for in-memory calculation, and the calculation accuracy is not limited to 1-bit. However, we can see the above examples that the core idea of in-memory calculations is generally to convert calculations into weighted calculations. Store the weights in the memory unit, then modifications on the core circuit of the memory (such as the readout circuit) are made. So that the process of reading is like a process in which the input data and weights are multiplied in the analog domain, that is, convolution. Because convolution is a core part of AI and other calculations, in-memory computing can be widely used in such applications. In-memory computing uses analog circuits for calculations, which is the difference compared with traditional digital logic calculations.In more traditional architectures, there are some multiply-accumulate circuits (MAC) for tensor math, especially the matrix multiplication. These architectures attempt to arrange the MAC in a way that moves weights and activations to the appropriate location. Activations are calculated from the previous neural network layer. Multiplication usually involves activations and weights, both must be moved to the place where multiplies them. In-memory computing makes use of it. Therefore, if the weights are stored in memory, the memory can access through activations to obtain multiplication and accumulation. The only difference from the actual memory is that the in-memory computing concatenates all word lines at once, instead of decoding the input to get one word line only.Figure 4. In-memory Computing Diagram3.2 Four Realization MethodsThe attempt is to enter the analog domain and treat the storage unit as an analog unit instead of a digital unit to reduce consumption. We have already got a way to use simulation on the front end of the inference engine. That is in-memory computing. Therefore, we take digital data, using a DAC to convert it to an analog value, and then driving a memory with these analog content to obtain an analog bit-line output, finally using an ADC to convert the result back to a digital format. However, the in-memory computing is still in the exploratory stage, and there are many specific implementation methods to study, currently there are three types: RRAM, Flash, SRAM, and DRAM.Based on RRAMRRAM is the most common method of doing this, because it is easy to use by applying Ohm's law to a series of resistors, but it still has the problem of relying on RRAM. The relationship between programming and resistance is non-linear, which requires more work to be done to make viable calculation circuits in RRAM memory for market. So it is just an idea, and the specific plan is still under study. Based on FlashNOR Flash memory has a more traditional word-line/bit-line structure. It is both resistive and capacitive. Generally, the memory cell is a transistor that is turned on or off. However, if it is partially conductive, it can be used as a resistor. The resistance depends on the amount of charge on the floating gate of the memory cell (capacitor). When running all the time, the cell will conduct to its maximum capacity. During this process, it does not conduct at all, however, it can be partially programmed. There is a problem is that you cannot precisely control the number of electrons. Moreover, the response to any number will vary with the process and temperature and other variables.Two companies are studying this method. Microchip owns their memBrain array, thanks to their acquisition of SST, and Mythic is a start-up company dedicated to an inference engine that uses in-memory computing with flash memory. Both companies said that they are using extensive calibration techniques to deal with this change.Another issue, flash cells will lose electrons over time. Electrons will flow around, which brings up an interesting topic: on this type of memory array, data retention and durability will be like.From the application point of view, it depends on whether it is to be used in cloud computing or edge inference engine. At the edge, it may perform certain fixed reasoning functions throughout the life cycle of the device. Therefore, if there are enough arrays, then you will load the weights for the first time and don't need to program it anymore (unless you do a update), because the flash memory is non-volatile. Although you still need to move activations, there is no need to move the weights, which will be stored permanently in the array. This would indicate that data durability (number of times the device can be programmed before cumulative damage accelerates electron leakages to an unacceptable level) does not matter, it only need to program once.In contrast, in cloud applications, the device is likely to be shared as a general-purpose computing resource, so this requires reprogramming for each new application. This means that battery life becomes more important in the cloud. Mythic claims to have a 10K write cycle, and has observed that even if it is reprogrammed every day, it will last for more than 10 years.If set an analog value for it and use an analog value in the cell, then in theory, each electron is important. However, if there is enough electron migration, you need to refresh the storage unit, or compensate for electrons change in some way. Because the same analog input today will produce different results than a year ago. The calibration circuit can also deal with some aging problems. However, for data retention, Mythic said they do perform regular updates of the weight values stored in flash memory. This will make persistence the main wear-out mechanism rather than data retention. Microchip stated that its data retention time is TBD, but it is likely to reprogram the device quarterly or annually to restore the unit.So they need a large number of high-quality ADCs and DACs to keep the signal-to-noise ratio (SNR) within a scope of accurate reasoning, which is the focus of designing work. Mythic claims that they provide a novel ADC, so that Microchip can share it to reduce the number required. Although ADC does consume energy, it also greatly reduces overall system consumption. Based on SRAMThis idea came from a lecture at Hot Chips at Princeton University. By definition, SRAM is a bistable unit. Therefore, it cannot be in an intermediate state, how should this be handled? And the DACs and ADCs that need to be corrected more over than the array in terms of area and power consumption.The point of this problem boils down to the question of how to simulate. They explained that this method uses more than one-bit line for calculation. Since the unit is still a digital value, it takes several bit lines to perform a calculation. The bit line can be split, and different groups perform different multiplications. The following figure illustrates it.Figure 5. Bit LineWith 8 inputs at a time, so the input vector is sliced and several consecutive multiplications are carried out to obtain the final results. The bit line charge is deposited on the capacitor. When ready to read, the charge is read out and sent to the ADC for conversion back to the digital domain. Their basic unit structure is as follows:Figure 6. Bit CellThese capacitors may affect chip size issues, but they said that the metal above the cell can be used. Of course, one cell is now 80% larger than the standard 6T SRAM cell (even without capacitors), but they say that their overall circuit is still much smaller than a required circuit based on standard digital implementation. In addition, since their basic array operations are still in digital form, they are less sensitive to noise and changes, which means their ADCs can be simpler and consume less power.Figure 7. Chip SizeBased on DRAMThis idea refers to not using a lot of power to obtain DRAM content, and in some way incorporate calculations into the CPU or other computing structures and directly run it on the DRAM die, which is what UPMEM does. A simple processor is built on the DRAM die, also the architecture will not compete with Xeon chips, they call this set "processing in memory" or PIM.Figure 8. PIM ChipInstead of bringing data to calculations, they bring calculations to data. The runtime is performed by the CPU in DRAM chip. That is, there is no need to move the data to any location outside of the DRAM chip, just send the calculating result back to the host system. Also, since ML calculations usually involve a lot of reduction, less data required for calculations. Although this does require some minor changes to the DRAM, they did not change the manufacturing process. Under this case, a standard DRAM module will provide multiple opportunities for distributed computing. At the same time, it becomes complicated to use this function to write a program.They said that a server using PIM offload will consume twice as much power than a standard server connected to a DRAM module without PIM. However, with a throughput of 20 times, it still provides them with a 10 times energy efficiency advantage. In addition, this method can help defend against side-channel security attacks. Thus a group of computing threads originally contained in one or more CPUs flows to DRAM. Therefore, it is necessary to check all DRAMs and figure out where thread is in some way, but this will be a difficult task. Ⅳ Driving Force of In-memory Computing and Market Prospects4.1 In-memory Computing for AIPeople have recognized the problem of "memory wall" for a long time, but why is in-memory computing only raised in the past two years? So we have to analyze the boost behind its rise.The first motivation is the rise of AI based on neural networks, especially the hope that AI can be popularized in mobile and embedded devices. So that in-memory computing with a high energy efficiency ratio has attracted attention. In addition, neural networks have a high tolerance for errors in calculation accuracy. Therefore, errors introduced in simulation calculations of in-memory computing can often be accepted. That is to say in-memory computing and AI are good partners for each other.The second motivation is the new memory. For in-memory computing, the memory characteristics often determine the efficiency of in-memory computing. Therefore, new memories improvement will often drive the development of in-memory computing. For example, the recently popular ReRAM uses resistance modulation to store data, so the readout of each bit uses a current signal instead of a traditional charge signal. In this way, it is a very natural operation for current to accumulate (combining several currents directly to achieve the sum of currents, even without additional circuits). That is to say, ReRAM is very suitable for in-memory calculations. From the perspective of memory promotion, new memories are also willing to catch up with the AT trend. Therefore, new memory manufacturers are also happy to see in-memory computing based on their own memories to accelerate AI development, which will broaden the memory market. 4.2 In-memory Computing Product OutlookChip products for in-memory computing are expected to come in two forms. The first form is sold as a memory IP with computing functions. Such memory IP may be traditional SRAM, or new memory such as eFlash, ReRAM, MRAM, and PCM.The second form is to directly build AI acceleration chips based on in-memory calculations. For example, Mythic plans to make PCIe accelerator cards based on flash memory, that is, access data with the main CPU through the PCIe interface. The weight data is stored on the Mythic memory chip, so that when the data is sent to the Mythic IPU, the calculation can be directly read out. In this way, the action of reading the weights data is eliminated.Figure 9. Mythic is a Pcie Accelerator 4.3 In-memory Computing Market and ProspectWhat impact will in-memory computing have on the AI chip market? First of all, we see that in-memory computing uses analog calculations, so its accuracy will be affected by the low signal-to-noise ratio. Usually the upper limit of accuracy is about 8-bit, and it can only do fixed-point calculations not the floating-point calculations. So in-memory computing is not suitable for the AI training market that requires high calculation accuracy. In other words, the main battlefield of in-memory computing is the AI inference market. For example, it is more suitable for embedded artificial intelligence, which has high requirements for energy efficiency not the accuracy. In fact, in-memory computing is actually most suitable for occasions where large memory is needed. For instance, flash is inherently required in IoT and other scenarios, so if you can add the in-memory computing to flash, it is quite suitable. However, introducing in-memory computing in a large storage memory may not appropriate. Based on this analysis, we believe that in-memory computing may become an important part of embedded AI (such as smart IoT) in the future. Ⅴ ConclusionWith the rise of AI and new memories, in-memory computing has also become a new hot spot. Based on the unique characteristics of the memory, it combines with analog calculations in memory, thereby greatly reducing the memory read and write operations in AI. Although the accuracy of calculation in the memory is limited by analog calculation, it is also suitable for embedded AI applications that pursue energy efficiency most and can accept a certain loss of accuracy. Frequently Asked Questions about In-Memory Computing Technology1. Why do we need in memory computing?In-Memory Computing provides super-fast performance (thousands of times faster) and scale of never-ending quantities of data, and simplifies access to increasing numbers of data sources. 2. What does in memory mean?An in-memory database is a type of purpose-built database that relies primarily on memory for data storage, in contrast to databases that store data on disk or SSDs. ... Because all data is stored and managed exclusively in main memory, it is at risk of being lost upon a process or server failure. 3. How does in memory computing work?In-memory computing means using a type of middleware software that allows one to store data in RAM, across a cluster of computers, and process it in parallel. Consider operational datasets typically stored in a centralized database which you can now store in “connected” RAM across multiple computers. 4. What is in memory computing in SAP HANA?An In-Memory database means all the data from source system is stored in a RAM memory. In a conventional Database system, all data is stored in hard disk. It provides faster access of data to multicore CPUs for information processing and analysis. 5. How is data stored in memory?Normally memory is described as a storage facility where data can be stored and retrieved by the use of an address. This is accurate but incomplete. A computer memory is a mechanism whereby if you supply it with an address it delivers up for you the data that you previously stored using that address. 6. What is in memory data processing?In-memory processing is the practice of taking action on data entirely in computer memory (e.g., in RAM). ... Since the storage appears as one big, single allocation of RAM, large data sets can be processed all at once, versus processing data sets that only fit into the RAM of a single computer. 7. What is in memory database processing and what advantages does it provide?The major advantage of systems using in-memory databases vs traditional database systems is: its performance speed. ... Source data is loaded into the system memory in a compressed and format. Therefore, in-memory processing reduces disk seek time for accessing data and streamlining the work involved in processing queries. 8. What is big data computing?Big data computing is an emerging data science paradigm of multi dimensional information mining for scientific discovery and business analytics over large scale infrastructure. ... Big data is characterized by 5V's such as volume, velocity, variety, veracity, and value.
kynix On 2020-11-30   10478
Resistors

Ideal Op-Amp Circuit Characteristics Update

IntroductionOperational amplifier (op amp for short) is basically a voltage amplifying device designed to be used with components like capacitors and resistors, between its in/out terminals, or is simply a linear Integrated Circuit (IC) having multiple-terminals. In electronics, the open-loop voltage gain of the actual operational amplifier is very large, which can be seen a differential amplifier with infinite open loop gain, infinite input resistance and zero output resistance. In addition, it has positive and negative inputs which allow circuits that use feedback to achieve a wide range of functions. And meanwhile, it can be further simplified into an ideal op amp model, referred to as an ideal op amp (also called ideal OPAMP).CatalogIntroductionⅠ Ideal Op Amp Characteristics1.1 Infinite Input Resistance1.2 Zero Output Impedance1.3 Infinite Open-loop Gain1.4 Infinite Common-mode Rejection Ratio1.5 Infinite BandwidthⅡ Assumptions of Ideal Op AmpⅢ Working Characteristics of Ideal Operational Amplifiers3.1 Work in Linear Region3.2 Work in Nonlinear RegionⅣ Analysis of Ideal Operational Amplifier CharacteristicsⅤ Balanced Resistance Presets5.1 The Role of Balanced Resistance5.2 Input Balancing Resistor ExplanationⅥ Ideal Op Amp EquationsⅦ Several Common Op Amp CircuitsⅧ Difference Between Ideal Op-amp and Practical Op-ampⅠ Ideal Op Amp CharacteristicsWhen analyzing various application circuits of operational amplifiers, the integrated operational amplifier is often regarded as an ideal operational amplifier. The so-called ideal op amp is to idealize various technical indicators of op amps, and it must have the following characteristics.Characteristics of An Ideal Op-Amp1.1 Infinite Input ResistanceThe input terminal of an ideal operational amplifier does not have any current to flow in. In electronics, op amps are voltage gain devices. They amplify a voltage fed into the op amp and give out the same signal as output with a much larger gain. In order for an op amp to receive the voltage signal as its input, the voltage signal must be dropped across the op amp. If you know the concept of a voltage divider, voltage drops primarily across components with high impedances, proportionally according to ohm’s law by the formula V=IR. So the greater the resistance (or impedance) of a device, the greater the voltage drop across that device is. To make sure that the voltage signal drops fully on the op amp, it must have a very high input impedance, so that the voltage drops fully across it. If it had a low input impedance, the voltage may not drop across it and it would not receive the signal. This is why op amps must have high-input impedances.It’s also easy to make the input impedance lower (put a resistor in parallel) or the source impedance higher (put a resistor in series).Figure 1. Ideal Op Amp Symbol and Transfer Characteristic Curve 1.2 Zero Output ImpedanceThe output of an ideal op amp is a perfect voltage source, no matter how the current flowing to the amplifier load changes, the output voltage of the amplifier is always a certain value, that is, the output impedance is zero. In practice, zero output impedance is actually a distinct property from infinite input impedance, but for a very long time infinite input impedance was approached only with compromises in offset voltage and noise. 1.3 Infinite Open-loop GainIn an open-loop state, the differential signal at the input has an infinite voltage gain. This feature makes the operational amplifier very suitable for practical applications with upper negative feedback configuration. 1.4 Infinite Common-mode Rejection RatioAn ideal operational amplifier can only respond to the difference between the voltages at both ends of V+ and V-. In addition, the same part of the two input signals (ie common mode signal) will be completely ignored. What’s more, a high CMRR is required when a differential signal must be amplified in the presence of a possibly large common-mode input, such as strong electromagnetic interference (EMI). An example is audio transmission over balanced line in sound reinforcement or recording. 1.5 Infinite BandwidthThe ideal operational amplifier will amplify the input signal of any frequency with the same differential gain, which will not change with the change of signal frequency.Ⅱ Assumptions of Ideal Op AmpThe op amp can be considered a voltage controlled current source, or it is an integrated circuit that can amplify weak electric signals. Based on it, for an ideal OPAMP, what is the relationship between it and these electrical signals?First, assume that the current flowing into the input of the op amp is zero. This assumption is almost completely correct for FET op amps, because the input current for FET op amps is below 1pA. But for dual high-speed op amps, this assumption is not always correct, because the input current of it can sometimes reach tens of microamperes.Second, assume that the gain of the op amp is infinite, so the op amp can swing the output voltage to any value to meet the input requirements. It means that the output voltage of the op amp can reach any value. In fact, when the output voltage is close to the power supply voltage, the op amp will saturate. Maybe this hypothesis does exit, but needs a limit in practical. For example, at higher frequencies, the internal junction capacitors of transistor come into play, thus reducing the output and therefore the gain of amplifier. The capacitor reactance decreases with increase in frequency bypassing the majority of output. The opamp is in saturation state.Figure 2. Op Amp SaturationFor example, as per datasheet of LM741, large signal voltage gain is 200V/mv. It means an open loop gain of 200,000. If you operate an op-amp in open-loop condition(i.e. without negative feedback) ,even microvolts of input voltage (input offset voltage of LM741 is 3mv) will drive the output to saturation.In most of the amplifier circuits op-amp is configured to use negative feedback which greatly reduces the voltage gain (i.e. closed loop gain). In oscillators and schmit triggers, Op-amp is configured to use positive feedback. Comparator circuit is an example of the circuit which utilizes open-loop gain of op-amp. Its output will be always at saturation either positive or negative saturation. In an integrator circuit, the DC gain should be limited by adding a feed back resistor in parallel with capacitor ;else the output will get saturated .Even in amplifier circuits, the amplitude of the input signal and the voltage gain of the circuit should be balanced so that the output voltage does not exceed power supply voltage . For example for a non-inverting amplifier with a voltage gain of 100, the maximum permissible input voltage will be 150 mv if the VCC is 15 Volts. If you apply a signal of 200 mv ,the op-amp output will goto saturation as the required output will be 20 volts which exceeds the VCC of 15 Volts.Third, the assumption of infinite gain also means that the input signal must be zero. The gain of the op amp will drive the output voltage until the voltage (error voltage) between the two input terminals is zero. The voltage between the two input terminals is zero. The zero voltage between two input terminals means that if one input terminal is connected to a hard voltage source like ground, the other input terminal will also be at the same potential. In addition, since the current flowing into the input terminal is zero, the input impedance of the op amp is infinite.Fourth, of course, the output resistance of an ideal op amp is zero. An ideal op amp can drive any load without any voltage drop due to its output impedance. At low currents, the output impedance of most op amps is in the range of a few tenths an ohm, so this assumption is true in most cases. Ⅲ Working Characteristics of Ideal Operational Amplifiers3.1 Work in Linear RegionWhen the ideal op amp works in the linear region, the output and the input voltage show a linear relationship. Where u0 is the output voltage of the integrated op amp; u+ and u- are the voltages at the non-inverting input terminal and the inverting input terminal, respectively. Auo is the open loop differential voltage magnification. According to the characteristics of the ideal op amp, two important characteristics of the ideal op amp in the linear region.1) Zero differential input voltageSince the open-loop differential voltage magnification of an ideal op amp is equal to infinity, and the output voltage is a certain value, the voltage values at the non-inverting input terminal and the inverting input terminal are approximately equal. Just like short circuit between input and output, but it is fake. Because it is an equivalent short circuit, not a real short circuit, so this phenomenon is called "virtual short".2) Zero input currentSince the open-loop input resistance of an ideal op amp is infinite, no current flows into the op amp at either input. At this time, the current at the non-inverting input terminal and the inverting input terminal are both equal to zero. Like an disconnection, but an equivalent disconnection, so this phenomenon is called "virtual break". Virtual short and virtual break are two important concepts for analyzing the ideal op amp working in the linear region.In fact, the ideal operational amplifier has the characteristics of "virtual short" and "virtual break". These two characteristics are very useful for analyzing linear amplifier circuits. The necessary condition for virtual short is negative feedback. When negative feedback is introduced, at this time, if the forward terminal voltage is slightly higher than the reverse terminal voltage, the output terminal will output a high voltage equivalent to the power supply voltage after the amplification of the op amp. In fact, the op amp has a respond time changing from the original output state to the high-level state (the golden rule of analyzing analog circuits: the change of the signal is a continuous change process). Due to the feedback resistance of the reverse end change will inevitably affect its voltage, when the reverse end voltage infinitely close to the forward end voltage, the circuit reaches a balanced state. The output voltage does not change anymore, that is, the voltage at the forward end and the reverse end is always close. (Note: The analysis method is the same when the voltage decreases.) 3.2 Work in Nonlinear RegionWhen the op-amp operates in the nonlinear region, the output voltage no longer increases linearly with the input voltage, but saturates. The ideal op amp also has two important characteristics when operating in the nonlinear region.1) When u+ ≠ u-, the output voltage of the ideal op amp reaches the saturation value.When u+ > u-, the op-amp operates works in positive saturation region with a positive output voltage.When u+ < u-, the op-amp operates works in negative saturation region with a negative output voltage.Ideal op amp operates in the nonlinear region, u+ ≠ u-, there is no “virtual short”.2) The input current is equal to zero.Although the input voltage u+ ≠ u- above, the input current is considered to be zero. Ⅳ Analysis of Ideal Operational Amplifier CharacteristicsAs for Op-amp, there's probably a description like this: three-terminal element (circuit structure with double-ended input, single-ended output), ideal transistor, high-gain DC amplifier.(1) High input resistanceUnder this situation, the current flowing into the input terminal is close to 0, almost no signal source current is used, which is close to the voltage control characteristic. And virtual break is derived from this.(2) Lower output resistanceIt has the characteristics of adapting to any load. And the impedance of the subsequent load circuit will not affect the output voltage.(3) Infinite voltage amplification(4) Under a certain supply voltage condition, the amplifier can only work in closed-loop (negative feedback) mode, and the actual amplification is limited. Because op-amps themselves don't have a 0V connection but their design assumes the typical signals will be more towards the center of their positive and negative supplies. Thus, if your input voltage is right at one extreme or forces the output toward one supply, chances are it won't work properly. Working in open-loop mode is the like a comparator, and the output is high level orlow level.In the closed-loop (limited amplification) state, the amplifier is randomly compare the potentials of the two input terminals. The output stage makes immediate adjustments when they are not equal. So the final purpose of amplification is to make the potentials of the two input terminals equal. And virtual short is derived from this. Ⅴ Balanced Resistance Presets5.1 The Role of Balanced Resistance1) A suitable resistance is generally required to ensure that the input impedance is matched.2) In order to reduce the input current imbalance, the in-phase resistor should be equal to the parallel value of the two resistors at the reverse end in theory. In practice, as a result of the closed loop, especially in deep negative feedback conditions, the misalignment is not obvious at the output. And there is no need of in-phase grounding resistor when the misalignment is not the main problem. Because a balanced resistor is the starting point for an ideal op amp. In-phase grounding resistance is useful for bipolar op amps, and has no meanings for MOS-type op amps.3) Ground input termination resistance: it is necessary for impedance matching and high frequency setting.4) Bias current and offset current.For operational amplifiers with bias current greater than offset current, input resistance matching can be reduced, and precision circuits can compensate bias current to a minimum. If the bias current and offset current are similar, the matching resistance will increase the error.5) Set for the bias current at the input, the purpose of which is to equalize the impedance of the invertingand non-inverting inputs, so that two inputs with equal bias currents are assumed to have equal voltage drops, thereby counteraction can be made. 5.2 Input Balancing Resistor ExplanationA op-amp is connected to an inverting amplifier:Set the input resistance for R1, feedback resistance for Rfi,Assume that the non-inverting end is not connected to a balanced resistor, but grounded directly.Set the input bias current for the op-amp IB (same voltage in inverting and non-inverting end).The current flows through R1 and Rf are represented by I1 and If.Inverting voltage is V-, The op-amp gain is A.Use KCL in the inverting end (set the input signal to 0).Where (0-V-)/R1- (A+1)V- /Rf=IBFrom the above equation, it follows that V-=-(IB×R1×Rf/(Rf+(A+1)R1))At this time, the output voltage of the op-amp is Vo=A×(IB×R1×Rf/(Rf+(A+1)R1))The above formula can be approximated as Vo=IB×((A×R1)/Rf)If the in-phase terminal passes through a resistor R2 to ground and R2=R1/Rf, then the voltage at the in-phase terminal is V+=-IB×R2KCL is applied to the inverted terminal, where (0-V-)/R1+(A×(V+-V-)-V-)/Rf=IBAt this time the output voltage of the op-amp is Vo=0. Ⅵ Ideal Op Amp EquationsUnderstanding the basic conditions of an ideal op amp, and combining it with the Kirchhoff's current law (KCL) node voltage method and the superposition theorem of the node, is an effective method to analyze the ideal op amp circuit.As shown below, find the output voltage uoFigure 3. OPAMP Circuit1) Equation based on KCLFrom the concept of virtual break, i+=i-=0, then i1=i2, i3=i4, so (a)Based on virtual break, u+=u-, then (b)2) Node voltage methodList the node voltage equations for node 1 and node 2, and get (c)Note: Because the output current of the op amp is unknown at 1) and 2), it is not possible to list the KCL equation or node voltage equation at the output of the op amp. In addition, the op amp output uo in 2) should be treated as an independent voltage source. 3) Superposition theoremWhen there are multiple signal inputs, choosing the superposition theorem to solve can simplify the analysis and calculation process. The size of the output signal uo can be regarded as the superposition of the output signal obtained by the independent action of u1 and u2. When u1 acts alone, the u2 terminal is grounded, and the op amp output is: (d)Therefore, the final output of the operational amplifier is:   (e) Ⅶ Several Common Op Amp CircuitsNon-inverting Amplifier CircuitA non-inverting amplifier is an op-amp circuit configuration which produces an amplified output signal. It provides a high input impedance along with all the advantages gained from using an operational amplifier. Inverting Amplifier CircuitAn inverting amplifier (also known as an inverting operational amplifier or an inverting op-amp) is a type of operational amplifier circuit which produces an output which is out of phase with respect to its input by 180 degrees out of phase with respect to input signal. In the following figure, two external resistors to create feedback circuit and make a closed loop circuit across the amplifier. Op-amp as AdderAn adder circuit can be made by connecting more inputs to the inverting op amp. The circuit diagram of a summing amplifier is as shown in the following figure. Differential AmplifierDifferential amplifier is an analog circuit with two inputs and and one output in which the output is ideally proportional to the difference between the two voltages. It is a very useful op-amp circuit and by adding more resistors in parallel with the input resistors as shown in the following. Composite AmplifierThe composite amplifier is termed as a combination of multiple operational amplifiers that are cascaded together with a negative-feedback loop around the entire network. The resistance in the circuit is generally selected at the K ohm level, the ratio of the resistance affects the gain and bias, in addition, the supply current, frequency response and capacitive load driving capability of the op amp determine their specific values in circuits. If it is used in a high-frequency circuit, the resistance needs to be reduced to obtain a better high-frequency response, but it will increase the input bias current, thereby increasing the current of the power supply. Ⅷ Difference Between Ideal Op-amp and Practical Op-ampIdeal op amps use no power, have infinite input impedance, unlimited gain-bandwidth and slew rate, no input bias current, and no input offset. They have unlimited voltage compliance.Practical op amps consume some power, have very high input impedance have limited gain-bandwidth and limited slew rate, have some input bias current and input offset voltage. Voltage compliance is limited by the power supply rail, or frequently even less.Still practical op amps are very useful because most of the limitations listed above are way better than what your circuit needs.For an ideal amplifier, it does not draw any current at all from its input. Assuming a two input amplifier the signal current in both input probes is zero. In other words the input impedance must be infinite. The output, should operate as the output of an ideal voltage source. This means that the potential between the output and the ground must be A(v2−v1), no matter how much current would a load connected to the output would draw. In other words the output impedance must be zero.For a real amplifier, the input impedance must be as large as possible while the output impedance must be as low as possible.In fact, An op-amp in real life, however, cannot operate with zero current flow. Frequently Asked Questions about Ideal Op Amp1. What is characteristic of ideal opamp?Ideal op amps will have infinite voltage gain, infinitely high impedance, zero output impedance, its gain is independent of input frequency, it has zero voltage offset, its output can swing positive or negative to the same voltages as the supply rails, and its output swings instantly to the correct value. 2. How does an ideal op amp work?An operational amplifier, or op amp, generally comprises a differential-input stage with high input impedance, an intermediate-gain stage, and a push-pull output stage with a low output impedance (no greater than 100 Ω). ... Open-loop voltage gain runs very high, on the order of 1 million. 3. Why are op amps not ideal?Op-amps with FET inputs have an Ibias that is so small that this method becomes less practical. Instead of measuring the voltage drop across a resistor, one can monitor the change in voltage across a capacitor as it is charged by the bias current. 4. How are real op amps different from ideal op amps?In real op amps, the amplified signal will not fully reach the DC supply rails. They will fall short of it. In an ideal op amp, the output will swing instantly to the amplified voltage value. There will be no time delay between the time the voltage is input into the op amp till the time it is output. 5. What are the four main ideal characteristics of an open-loop op amp?An ideal op amp is usually considered to have the following characteristics:Infinite open-loop gain G = vout / vInfinite input impedance Rin, and so zero input currentZero input offset voltageInfinite output voltage rangeInfinite bandwidth with zero phase shift and infinite slew rateZero output impedance R
kynix On 2020-11-06   6776
Resistors

PCB Design: How to Draw Circuit Diagram of PCB?

IntroductionPCB exists in every electronic device. A fully functional PCB is mainly used to create connections between components, such as resistors, capacitors, inductors, diodes, transistors, integrated chips, etc. It is the carrier of the entire logic circuit. Sound PCB design can save production costs, and achieve good circuit performance and heat dissipation effect. PCB designs vary in complexity according to product needs. This article mainly talks about wiring, one of the basics of PCB design.PCB Design: From Idea to Schematic to PCBCatalogIntroductionⅠ PCB Basics: Wiring RulesⅡ Three PCB Wiring MethodsⅢ PCB Design: Wire InspectionⅣ Complete PCB Design Projects Inspection4.1 General PCB Design Inspection Projects4.2 PCB Electrical Characteristics Checking Projects4.3 PCB Physical Characteristics Checking Projects4.4 PCB Mechanical Design Factors4.5 PCB Installation Requirements4.6 PCB Pull-out Requirements4.7 PCB Mechanical Considerations4.8 PCB Electrical Considerations4.9 Electronics Inspection Before Into A PCBⅤ ConclusionⅠ PCB Basics: Wiring Rules1. The area within 1mm from the edge of the PCB board and within 1mm around the mounting hole will not take wiring.2. The power line width should not be less than 18mil; the signal line width should not be less than 12mil; the cpu input and output lines should not be less than 10mil (or 8mil); the line spacing should not be less than 10mil.3. It is necessary noted that the power line and the ground line should be as radial as possible, and the signal line must not be looped.4. Ground circuit rulesThe loop area formed by the signal line should be as small as possible. The smaller the loop area, the less external radiation and the less interference from the outside. An example is shown in the figure below:5. Crosstalk controlHere crosstalk refers to the mutual interference caused by long parallel wiring between different networks on the PCB, which caused by the distributed capacitance and inductance between the parallel lines. The main measures to overcome it are:a. Increase the spacing of parallel wiring and follow the 3W rule. To ensure that the distance between the lines is large enough, when the distance between the line and the center of the line is not less than 3 times the line width (as shown in the figure below). If the line center distance is not less than 3 times the line width, 70% of the line electric fields will not interfere with each other, which is called 3W rule.b. Insert a grounded isolation wire between the parallel wires. Reduce the distance between the wiring layer and the ground plane.6. The direction control rules of routing:The routing directions of adjacent layers are orthogonal. Different signal lines in the same direction on adjacent layers should be avoided to reduce unnecessary interlayer crosstalk. When the signal rate is high, use a ground plane to isolate each wiring layer, in other words, isolate each signal line with ground line. The neighbouring wires used in the input and output end of the circuit shouldn’t be parallel to prevent the feedback, and it is best to add a ground wire between these wires.7. Open loop inspection rules for wiring:Generally, it is not allowed to have a floating wiring at one end, because of the "antenna effect" and unnecessary interference radiation and reception, which may bring unpredictable results.8. Impedance matching inspection rulesThe wiring width of the same network should be kept the same. Line width variations will bring uneven line characteristic impedance, and reflection will occur when the transmission speed is high. This situation should be avoided in the design. Under certain conditions, such as the lead wires of the connector and the similar structure of the lead wires of the BGA package, the change of the line width may not be avoided, so that the length of the middle inconsistent part should be minimized.9. Wiring closed loop inspection rules:Prevent signal lines from forming self-loops between different layers. Such problems are prone to occur in multilayer board design, and it will cause radiation interference. As shown below:10. The branch length control rule of wiring:Try to control the length of branches, and the general requirement is Tdelay≤Trise/20.11. Resonance rules of wiring:For high-frequency signal design, the wiring length must not be an integer multiple of its wavelength to avoid resonance.12. Line length control rules:In fact, it refers to the short-circuit rule. When designing, you should keep the wiring length as short as possible to reduce interference problems caused by unnecessary lines. Especially for some important signal lines, such as clock lines, be sure to place oscillators close to the device. In the case of driving multiple devices, the network topology should be decided according to the specific situation.13. Parallel input and output wires on the PCB board should be avoided as far as possible to avoid parallel. It is best to place a ground wire between the two wires to avoid circuit feedback coupling.14. Digital ground and analog ground should be separated. For low-frequency circuits, single-point parallel grounding should be used. High-frequency circuits should be grounded in series with multiple points. For digital circuits, the ground wire should be closed into a loop to improve anti-noise capability.15. The wiring and via distribution of the whole circuit board should be uniformity. When the outer signal of the circuit board has a large blank area, auxiliary lines should be added to make the lines distribution on the board basically balanced.16. The low-frequency circuit can be grounded at a single point in parallel, and the actual wiring can be connected in series and then grounded in parallel. The high-frequency circuit can be grounded in series with multiple points. The ground wire should be short and thick. For high-frequency components, a large area ground foil can be used. The ground wire should be as thick as possible. If the ground wire is a very thin, the ground potential will change with the current, which reduces the noise resistance.17. Multilayer boards should be as symmetrical as possible when designing the laminated structure, as well as the wiring density and copper layout of each layer to reduce warpage and reduce EMI during soldering.18. The signal line should not cross the power supply and ground. The signal reference plane should be as complete as possible.19. Impedance controlThe signal lines that need impedance control must be wired in strict accordance with the calculated data, in addition, it is necessary to tell manufacturers it. For signal lines that do not require it, the impedance should be calculated to prevent unnecessary interference.20. Grid copper should be used less in low frequency circuits. Although it can effectively reduce the problem of large area copper skin blistering. When using grid copper, you need to consider the electrical length of the grid line and the working frequency of the circuit board. If using grid copper, the power supply should also be coated with solid copper as much as possible.21. A group of buses with the same attribute should be wired side by side as much as possible, and the length should be as equal as possible. Ⅱ Three PCB Wiring MethodsThe wires should take the shortest route between components according to the specified wiring rules. Limit the coupling between parallel wires as much as possible. Good PCB design requires the minimum number of wiring layers, and also requires fair use of the widest wire and the largest pad size corresponding to packaging density. For example, rounded corners and smooth inner corners design may avoid some electrical and mechanical problems, therefore, sharp corners and sharp corners in the wire should be avoided. Here introduces three main PCB routing methods; right-angle wiring, differential wiring, and serpentine wiring to illustrate PCB layout:A. The influence of right-angle wiring on the signal is mainly reflected in three aspects:1. The corner can be equivalent to the capacitive load on the transmission line to slow down the rise time.2. Discontinuous impedance will cause signal reflection.3. The EMI generated by the right-angle tip reaches the RF field above 10GHz. Such a right-angle is likely to develop into the source of high-speed problems. B. To figure out what is differential wiring, you must first understand what is differential signal. In a word, the driving end sends two equal and inverted signals, and the receiving end judges the logic state "0" or "1" by comparing the difference between the two voltages. The pair of traces carrying differential signals is called differential traces. Compared with ordinary single-ended signal traces, differential signals have the most obvious advantages in the following three aspects:1. Have Strong anti-interference ability. Because the coupling between the two differential traces occurs, when there is noise interference from the outside, they are almost coupled to the two lines at the same time. However, the receiving end only cares about the difference between the two signals. Therefore, the external common mode noise can be completely canceled.2. It can effectively suppress EMI. Due to the opposite polarity of the two signals, the electromagnetic fields radiated by them can cancel each other out. What’s more, the tighter the coupling, the less the electromagnetic energy leaked to the outside world.3. The timing positioning is accurate. Because the switch change of the differential signal is located at the intersection of the two signals. Unlike ordinary single-ended signals, which rely on the high and low threshold voltages to judge. Timing positioning is less affected by the process and temperature, and also more suitable for circuits with low amplitude signals. The current popular LVDS (low voltage differential signaling) refers to this small amplitude differential signaling technology. C. Serpentine line is a type of wiring method often used in PCB layout. Its main purpose is to adjust the delay to meet the system timing design requirements. The two most critical parameters are the parallel coupling length (Lp) and the coupling distance (S). Obviously, when a signal is transmitted on a serpentine trace, the parallel line segments will be coupled in a differential mode. The smaller the S, the greater the Lp, the greater the coupling. It may cause the transmission delay to be reduced, also the signal quality is greatly reduced due to crosstalk. The mechanism can refer to the analysis of common mode and differential mode crosstalk. The following are some suggestions when dealing with serpentine wring:1. Try to increase the distance (S) of parallel lines, at least more than 3H(H refers to the distance from the signal trace to the reference plane). As long as S is large enough, the mutual coupling effect can be almost completely avoided.2. Reduce the coupling length Lp. When the double Lp delay approaches or exceeds the signal rise time, the crosstalk generated will reach saturation.3. The signal transmission delay caused by the strip-line or embedded micro-strip line is less than that of the micro-strip. Theoretically, the strip-line will not affect the transmission rate due to differential mode crosstalk.4. For signal lines with high-speed and strict timing requirements, try not to take serpentine lines, especially in a small area.5. You can often use s-shaped routing at any angle, which can effectively reduce the mutual coupling.6. In high speed, the serpentine line has no ability so-called filtering or anti-interference, and can only reduce the signal quality, so it is better to use for timing matching.7. Sometimes you can consider the spiral routing method for winding. Simulation shows that its effect is better than normal serpentine routing.Ⅲ PCB Design: Wire Inspection1.Wire SpacingThe minimum spacing of wires must be determined to eliminate voltage breakdown or arcing between adjacent wires. The spacing is variable, it mainly depends on the following factors:1) Peak voltage between adjacent wires2) Atmospheric pressure (maximum working altitude)3) Coating layer4) Capacitive coupling parametersComponents with critical impedance or high-frequency components should be placed very close to reduce the critical stage delay. There is something need to pay attention to. Transformers and inductive components should be isolated to prevent coupling. Inductive signal wires should be laid orthogonally at right angles. Components that generate any electrical noise due to magnetic field movement should be isolated or rigidly installed to prevent excessive vibration.2. Whether the wire is short and straight without sacrificing function.3. Whether the restrictions on the wire width are complied with.4. There must be a minimum distance between wires, wires and mounting holes, wires and pads.5. Whether to avoid all the wires (including component leads) closer to parallel wiring.6. Whether sharp corners (≤90℃) are avoided in the wire pattern. Ⅳ Complete PCB Design Projects Inspection4.1 General PCB Design Inspection Projects1) Has the circuit been analyzed? Is the circuit divided into basic units to smooth the signal?2) Does the circuit allow short or isolated key leads?3) Where must be shielded, are they effectively shielded?4) Have you made full use of the basic grid graphics?5) Is the best size of the printed circuit board?6) Do you use the available wire width and spacing as much as possible?7) Has the preferred pad size and hole size been used?8) Are the base plate and the sketch consistent?9) Is less cross-wiring used? Do cross wires pass through components and accessories?10) Are the letters visible after assembly? Are their size and model correct?11) In order to prevent blistering, is there any window on the large area of copper foil?12) Are there tool positioning holes?4.2 PCB Electrical Characteristics Checking Projects1) Have you analyzed the influence of wire resistance, inductance, and capacitance, as well as the critical voltage drop on the ground?2) Does the wire spacing and shape meet the insulation requirements?3) Has the insulation resistance value been controlled and specified in key areas?4) Is the polarity fully recognized?5) According to geometric view, has the effect of wire spacing on leakage resistance and voltage been measured?6) Has the medium for changing the surface coating been identified?4.3 PCB Physical Characteristics Checking Projects1) Are all pads and their positions suitable for final assembly?2) Can the assembled PCB meet the shock and vibration conditions?3) What is the required spacing of standard components?4) Are the components that are not firmly installed or the heavier parts fixed?5) Is the heating element heat dissipation and cooling normally? Or is it isolated from the printed circuit board and other heat-sensitive elements?6) Are the voltage divider and other multi-lead components placed correctly?7) Is the arrangement and orientation of components easy to check?8) Has it eliminated all possible interference on the printed circuit board?9) Is the size of the positioning hole correct?10) Are the tolerances complete and reasonable?11) Have you controlled and signed the physical properties of all coatings?12) Is the ratio of via hole and lead diameter within an acceptable range?4.4 PCB Mechanical Design FactorsThe printed circuit board adopts mechanical methods to support the components, however, it cannot be used as an unique structural part of the entire device. On the edge of the printing plate, at least every 5 inches for a certain support. The factors that must be considered when selecting and designing printed circuit boards are as follows:1) The size and shape of the printed circuit board.2) The type of mechanical accessories and plug (seat) required.3) The environmental adaptability of circuits.4) According to some factors, such as heat and dust, install the printed circuit board vertically or horizontally.5) Some environmental factors that require special attention, such as heat dissipation, ventilation, shock, vibration, and humidity, dust, and radiation, etc.6) Physical support7) Install and fix.8) Disassemble4.5 PCB Installation RequirementsAccording to practical experience, the distance between the supporting points of a printed circuit board with a thickness of 0.031-0.062 inches should be at least 4 inches. For a printed circuit board with a thickness greater than 0.093 inches, the distance between the supporting points should be at least 5 inches. Taking this measure can improve the rigidity of the printed circuit board and avoid possible resonance. The following factors should be considered before deciding which mounting technology they use.1) PCB structure.2) Input and output terminals.3) Available equipment space.4) Convenience of loading and unloading.5) Type of attachments.6) Required heat dissipation.7) Required shieldability.8) The type of circuit and its relationship with other circuits.4.6 PCB Pull-out Requirements1) The influence of plugging tools on the installation distance between two printed circuit boards.2) When the plug-in tool used in the equipment, its size should be considered.3) A plug-in device is required, which is usually fixed to the printed circuit board assembly with rivets.4) As for the mounting frame of the printed circuit board, special design such as load bearing flange is required.5) The adaptability of the plug-in tool used and the size, shape and thickness of the printed circuit board.4.7 PCB Mechanical ConsiderationsThe characteristics of the board substrate that have an important influence on the printed circuit assembly are: water absorption, thermal expansion coefficient, heat resistance, flexural strength, impact strength, tensile strength, shear strength and hardness. All these characteristics affect the function and the production efficiency of the printed circuit board structure. For most applications, the dielectric substrate materials of the printed circuit board are as following:1) Phenolic impregnated paper2) Acrylic-polyester impregnated randomly arranged glass mat3) Epoxy impregnated paper4) Epoxy impregnated glass clothEach substrate can be flame retardant or combustible. The first 3 types mentioned above can be processed. The most common used material for printed circuit boards with metalized holes is epoxy-glass cloth. Its dimensional stability is suitable for high-density circuits and can minimize the occurrence of cracks in the metalized holes. One disadvantage of epoxy-glass cloth laminate is that it is difficult to punch in the usual thickness range of printed circuit boards. For this, all holes are usually drilled and copied and milled to form a print shape of the circuit board.4.8 PCB Electrical ConsiderationsIn DC or low-frequency AC applications, the most important electrical characteristics of insulating substrates are: insulation resistance, anti-isolation, printed wire resistance, and breakdown strength. In high frequency and microwave applications, include: dielectric constant, capacitance, and dissipation factors. In all applications, the current carrying capacity of printed wires is important.4.9 Electronics Inspection Before Into A PCB1) Check the rationality and correctness of the schematic diagram.2) Check the correctness of the component packaging of the schematic.3) The distance between strong and weak current lines, and the distance between isolation areas.4) Check the schematic diagram and PCB diagram to prevent the loss of the network table.5) Whether the package of the component matches the physical object.6) Whether the placement of the components is appropriate.7) Whether the components are easy to install and disassemble.8) Whether the temperature sensitive element is too close to the heating element.9) Whether the distance and direction of the mutual inductance components are appropriate.10) Whether the placement between the connectors is smooth.11) Easy to plug in and plug out12) Input and output13) Strong current and weak current14) digital and analog should be interlaced.15) Arrangement of elements on the upside and downside16) Check whether the directional component has been wrong flipped instead of rotated.17) Check whether the mounting holes of the component pins are suitable and whether it is easy to insert.18) Check whether the empty pin of each component is normal and whether it is a missing line.19) Check whether there are vias between the upper and lower wiring of the same net table. And the pads are connected through the holes, to prevent disconnection and ensure the integrity of the circuit.20) Silk screen printing should be clear, so that the operation of welding or maintenance can be easy.21) The arrangement of power and signal lines in the socket should ensure signal integrity and anti-interference.22) Pay attention to the proper ratio of pads and solder holes.23) Each plug should be placed on the edge of the PCB board as much as possible and easy to operate.24) Whether the size and distribution of the mounting holes on the PCB are appropriate to reduce the PCB bending stress.25) Pay attention to the height distribution of the components on the PCB to ensure easy assembly.Ⅴ ConclusionBased on the above mentioned rules, drawing the PCB schematics you need becomes easier. Decide what PCB you want to and install a PCB design software. PCB software is really helpful and powerful. Also a software can check your design to make sure the design does not contain errors such as traces that incorrectly touch, traces too skinny, or drill holes that are too small. For example, run the Electrical Rules Checker (ERC) to see if you’ve made any typical errors. There is less thing stopping you from making your first PCB, right? Frequently Asked Questions about PCB Design Diagram1. Which side of PCB is correct for soldering?The bottom side of the PCB is usually the side without components and the side that touches the solder wave during assembly. That is why sometimes it is also called SOLDER side. However more often, PCB are populated on both sides and the assembly process does not require wave soldering. 2. Which soldering method is suitable for soldering printed circuit board?Soldering Iron – Used to melt solder and connect component pins to board pads. A cheap soldering pencil may be sufficient, but a temperature-controlled solder station is best for high performance boards. Solder – An alloy of tin and lead with a low melting point. 3. What is PCB diagram?A PCB schematic is a simple two-dimensional circuit design showing the functionality and connectivity between different components. ... Once the blueprint has been completed, the PCB design comes next. The design is the layout, or physical representation of the PCB schematic and includes the copper track and hole layout. 4. Why we use PCB in soldering?PCB soldering is another term for the process of soldering electrical circuit boards. ... As the soldering iron melts this metal, it is then used a bit like glue to stick to pieces together. As the solder metal cools, it will re-harden into one large shape that connects the two parts. 5. How do you read a PCB board?Start with an easy analog circuit, such as a guitar distortion pedal, and work your way up to more complicated versions. Make a drawing of the top of the circuit board. Show the positions of the capacitors, integrated circuits, resistors, transistors and other components. Review it to make sure everything is included.
kynix On 2020-10-13   6810

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.