Phone

    00852-6915 1330

emi Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

General electronic semiconductor

Remote Electronic Transport Promote Organic Photovaltaic Power Generation

SummaryFor years,people had treated the poor conductivity of organics as an unavoidable fact,and this shows that that is no always the case. Said Stephen Forrest,the Peter A. Franken Distinguished University Professor of Engineering and Paul G. Goebel Professor of Engineering at U-M, who led the research,which is  a way to coax electrons to travel much further than was previously thought possible in the materials often used for organic solar cells and other organic semiconductors under the condition of pushing cheap,ubiquitous solar power closer to reality. The fatal weakness of organic material may adjust its conductivityUnlike the inorganic solar cells widely used today, organics can be made of inexpensive, flexible carbon-based materials like plastic. Manufacturers could churn out rolls of them in a variety of colors and configurations, to be laminated unobtrusively into almost any surface. Organics’ notoriously poor conductivity, however, has slowed research. Forrest believes this discovery could change the game.  The team showed that a thin layer of fullerene molecules—the curious round carbon molecules also called Buckyballs—can enable electrons to travel up to several centimeters from the point where theyre knocked loose by a photon. That’s a dramatic increase; in today's organic cells, electrons can travel only a few hundred nanometers or less. But organic materials have much looser bonds between individual molecules, which can trap electrons. This has long been an Achilles’ heel of organics, but the new discovery shows that it may be possible to tweak their conductive properties for specific applications. The ability to make electrons move more freely in organic semiconductors The ability to make electrons move more freely in organic semiconductors could have far-reaching implications. For example, the surface of today's organic solar cells must be covered with a conductive electrode that collects electrons at the point where they’re initially generated. But freely moving electrons can be collected far away from their point of origination. This could enable manufacturers to shrink the conductive electrode into an invisible grid, paving the way for transparent cells that could be used on windows and other surfaces. “This discovery essentially gives us a new knob to turn as we design organic solar cells and other organic semiconductor devices,” said Quinn Burlingame, a U-M electrical engineering and computer science graduate researcher and author on the study. “The possibility of long-range electron transport opens up a lot of new possibilities in device architecture.” Burlingame says that the initial discovery of the phenomenon came as something of an accident as the team was experimenting with organic solar cell architecture in hopes of boosting efficiency. Using a common technique called vacuum thermal evaporation, they layered in a thin film of C60 fullerenes—each made of 60 carbon atoms—on top of an organic cell's power-producing layer, where the photons from sunlight knock electrons loose from their associated molecules. On top of the fullerenes, they put another layer to prevent the electrons from escaping. They discovered something they’d never seen before in an organic—electrons were skittering unfettered through the material, even outside the power-generating area of the cell. Through months of experimentation, they determined that the fullerene layer formed what's known as an energy well—a low-energy area that prevents the negatively charged electrons from recombining with the positive charges left behind in the power-producing layer.“You can imagine an energy well as sort of a canyon—electrons fall into it and can’t get back out,” said Caleb Cobourn, a graduate researcher in the U-M Department of Physics and an author on the study. “So they continue to move freely in the fullerene layer instead of recombining in the power-producing layer, as they normally would. It's like a massive antenna that can collect an electron charge from anywhere in the device.”Forrest cautions that widespread use of the discovery in applications like solar cells is theoretical at this point. But, he is excited by the discovery’s larger implications for understanding and exploiting the properties of organic semiconductors. “I believe that ubiquitous solar power is the key to powering our constantly warming and increasingly crowded planet, and that means putting solar cells on everyday objects like building facades and windows,” Forrest said. “Technology like this could help us produce power in a way that’s inexpensive and nearly invisible.” The study is titled “Centimeter-Scale Electron Diffusion in Photoactive Organic Heterostructures.” The research was supported by the U.S. Department of Energy SunShot Program and by the Air Force Office of Scientific Research.    Article from University of MichiganArticle edited by kynix 
kynix On 2018-01-23   356
General electronic semiconductor

Make Next-Gen of Computer Be Faster,Better, More efficient

SummaryAn innovative new method to engineer computer chips more easily and cheaper than conventioanl methods have been developed by researchers who from the University of Exeter.This new technique to produce cutting-edge,versatile microchips could revolutionize the speed,efficiency and capability of the next-gen of computers.About the researchThe discovery could revolutionise the production of optoelectronic materials – or devices that produce, detect and control light – which are vital to the next generation of renewable energy, security and defence technologies, the researchers said.Dr Anna Baldycheva, from Exeter's Centre for Graphene Science and author of the paper said:"This breakthrough will hopefully lead to a revolution in the development of vital new materials for computer electronics. The work provides a solid platform for the development of novel next-generation optoelectronic devices. Additionally, the materials and methods used are extremely promising for a wide range of further potential applications beyond the current devices." This innovative new research focused on developing a versatile,multi-functional technology to significantly enhance future computing capabilities. The team used microfluidics technology, which uses a series of minuscule channels in order to control the flow and direction of tiny amounts of fluid. For this research, the fluid contains graphene oxide flakes,that are mixed together in the channels, to construct the chips.While the graphene oxide flakes are two-dimensional- consisting of length and width only- the research team used a new sophisticated light-based system to drive the assembly of the three-dimensional chip structures.Crucially, the research team have analysed their methodology to not only confirm the technique is successful, but also to provide a blueprint for others to use to help manufacture the chips. "We are very excited about the potential of this breakthrough and look forward to seeing where it can take the optoelectronics industry in the future." added by professor Monica Craciun, co-author of the paper and Associate Professor of Nanoscience at Exeter.  This article provide by University of Exeter,and the research is  published in the respected journal Scientific Reports.Article edited by kynix. 
kynix On 2018-01-22   312
Power

If Power Electronics Support Market Growth in the Futher

SummaryAccording to recent market research by Grand View Research,the global power electronics market will be valued at $39.2bn by 2025.To ensure electrical products and infrastructure are capable of supporting this 40% growth, REO UK is calling on laboratories and testing facilities to invest in stable DC power supplies for electrical testing. Electrical testing is a critical part of the design and development of power electronics and electrical components. Electricla Testing WorkElectrical testing involves running accurately monitored voltages through a component or product to ensure it is capable of withstanding and performing under specified currents. This ensures smooth performance and correct specification details once the tested equipment is on the market.  REO UK has worked extensively with test facilities and laboratories in the past and has identified a recurring problem of poor power quality affecting test accuracy. The company has previously launched ranges of electrical power supplies to provide stepless voltage adjustment to overcome this issue.  Steve Hughes,Managing Director of REO UK said: " Testing requires absolute accuracy to ensure  that products are reliable,safe and able to perform,if the market for power electronics is to reach its projected 40% growth in the coming decade, testing must be accurately controlled and reliable to ensure a consistently high standard of products."  Test Facilities disadvantage"Unfortunately,we often see that test facilities lack this control, either due to inaccurate electrical equipment or electromagnetic interference (EMI) making the current unreliable.” Up to now, the company has  stepped up its focus on test facilities with its new REOLAB 1000E electronic DC power supply for test equipment. The product is designed for use in testing the operating current of semiconductor diodes and rectifiers, as well as the maximum DC reverse voltage of a system up to 1,200V.  “Our new REOLAB 1000E helps to tackle the lack of electrical control with its stepless voltage adjustments and current tolerance of ±1%,” continued Hughes. “This tolerance level means that the supplied power is highly accurate and controllable.“In addition to this, the REOLAB range has a design that complies with electromagnetic compatibility (EMC) standards to prevent creating power quality problems. This ensures test and laboratory facilities can test properly and effectively with minimal concerns over unstable loads.” 
kynix On 2017-12-20   281
General electronic semiconductor

A New Breakthrough In Organic Electronics

SummaryPublished in the Joural Nature Materials in Nov.13,2017,reaearchers from Princeton University,the Georgia Institute of Technology and Humboldt Uniersity in Berlin is pointing the way to possibly more widespread use of organic electronics. Their research focuses on organic semiconductors,a class of materials prized for their applications in emerging technologies such as flexible electronics, solar energy conversion, and high-quality color displays for smartphones and televisions. In the short term, the advance should particularly help with organic light-emitting diodes that operate at high energy to emit colors such as green and blue.  Body“Organic semiconductors are ideal materials for the fabrication of mechanically flexible devices with energy-saving low-temperature processes,” said Xin Lin, a doctoral student in electrical engineering at Princeton and the lead author. “One of their major disadvantages has been their relatively poor electrical conductivity. In some applications, this can lead to difficulties and inefficient devices. We are working on new ways to improve the electrical properties of these organic semiconductors.” Semiconductors, typically made of silicon, are the foundation of modern electronics because engineers can take advantage of their unique properties to control electrical currents. Among many applications, semiconductor devices are used for computing, signal amplification and switching( signal switches ). They are used in energy-saving devices such as light-emitting diodes and devices that convert energy such as solar cells. In the doping process used to make semiconductors their chemical makeup is modified by adding a small amount of chemicals or impurities. By carefully choosing the type and amount of dopant, researchers are able to alter the electronic structure and electrical behaviour of the semiconductor in a number of ways. As the article shows,researchers have developed an approach for greatly increasing the conductivity of organic semiconductors,which are formed of carbon-based molecules rather than silicon atoms. The dopant, a ruthenium-containing compound, is a reducing agent, which means it adds electrons to the organic semiconductor as part of the doping process. The addition of the electrons is the key to increasing the semiconductor’s conductivity. The compound belongs to a newly introduced class of dopants called dimeric organometallic dopants. Unlike many other powerful reducing agents, these dopants are stable when exposed to air but still work as strong electron donors both in solution and solid state. Seth Marder and Stephen Barlow from the Georgia Institute of Technology, who led the development of the new dopant, called the ruthenium compound a “hyper-reducing dopant.” They said it is unusual, not only in its combination of electron donation strength and air stability, but in its ability to work with a class of organic semiconductors that have previously been very difficult to dope. In studies conducted at Princeton, the researchers found that the new dopant increased the conductivity of these semiconductors about a million times. The ruthenium compound is a dimer, which means it consists of two identical molecules, or monomers, connected by a chemical bond. As is, the compound is relatively stable and, when added to these difficult-to-dope semiconductors, it does not react and remains in its equilibrium state. That posed a problem because to increase the conductivity of the organic semiconductor, the ruthenium dimer needs to react with the semiconductor it and then split apart. The researchers looked for different ways to break up the ruthenium dimer and activate the doping, eventually they added energy by irradiating with ultraviolet light, which effectively excited the molecules in the semiconductor and initiated the reaction. Under exposure to the light, the dimers split into monomers, and the conductivity rose. "Once the light is turned off, one might expect the reverse reaction to occur" and the increased conductivity to disappear, Marder said. "However, this is not the case." The researchers found that the ruthenium monomers remained isolated in the semiconductor even though thermodynamics should return the molecules to their original configuration as dimers. The team's hypothesis is that the monomers are scattered in the semiconductor in such a way that it is very difficult for them to return to their original configuration and re-form the ruthenium dimer. They are, according to the team “kinetically trapped." The researchers also discovered that doping was continuously re-activated by the light produced by the device. The light activates the system more, which leads to more light production and more activation until the system is fully activated, Marder said. "This alone is a novel and surprising observation." The work was supported in part by the National Science Foundation and the U.S. Department of Energy. Article edited by kynix   
kynix On 2017-11-28   355
Sensor

New Technology--Unique Microchip Tracks Smart Pills and Biosensors

SummaryResearchers at Caltech have developed a prototype miniature medical device that could ultimately be used in “smart pills” to diagnose and treat diseases. This is critical for the function of biosensors and smart pills. A key to the new technology—and what makes it unique among other microscale medical devices—is that its location can be precisely identified within the body, something that proved challenging before. The picture is about an ATOMS microchip localized within the gastrointestinal tract. bodyCalled ATOMS, which is short for addressable transmitters operated as magnetic spins, the new silicon-chip devices borrow from the principles of magnetic resonance imaging (MRI), in which the location of atoms in a patient's body is determined using magnetic fields. The microdevices would also be located in the body using magnetic fields—but rather than relying on the body's atoms, the chips contain a set of integrated sensors, resonators, and wireless transmission technology that would allow them to mimic the magnetic resonance properties of atoms. The ATOMS device seen next to a penny. The device has a surface area of 1.4 square millimeters, 250 times smaller than a penny. A key principle of MRI is that a magnetic field gradient causes atoms at two different locations to resonate at two different frequencies, making it easy to tell where they are. The researchers wanted to embody this elegant principle in a compact integrated circuit. ATOMS devices also resonate at different frequencies depending on where they are in a magnetic field. The scientists wanted to make this chip very small with low power consumption, and that comes with a lot of engineering challenges. They had to carefully balance the size of the device with how much power it consumes and how well its location can be pinpointed.The devices are still preliminary but could one day serve as miniature robotic wardens of our bodies, monitoring a patient's gastrointestinal tract, blood, or brain. They could measure factors that indicate the health of a patient—such as pH, temperature, pressure, sugar concentrations—and relay that information to doctors. Or, the devices could even be instructed to release drugs. Microscale and Biosensors You could have dozens of microscale devices and biosensors -traveling around the body taking measurements or intervening in disease. These devices can all be identical, but the ATOMS devices would allow you to know where they all are and talk to all of them at once. The researchers compare it to the 1966 sci-fi movie Fantastic Voyage, in which a submarine and its crew are shrunk to microscopic size and injected into the bloodstream of a patient to heal him from the inside—but, instead of sending a single submarine, you could send a flotilla. The researchers say the devices are still preliminary but could one day serve as miniature robotic wardens of our bodies, monitoring a patient's gastrointestinal tract, blood, or brain. The devices could measure factors that indicate the health of a patient—such as pH, temperature, pressure, sugar concentrations—and relay that information to doctors. Or, the devices could even be instructed to release drugs. This chip is totally unique: there are no other chips that operate on these principles. Integrating all of the components together in a very small device while keeping the power low was a big task. The final prototype chip, which was tested and proven to work in mice, has a surface area of 1.4 square millimeters, 250 times smaller than a penny. It contains a magnetic field sensor, integrated antennas, a wireless powering device, and a circuit that adjusts its radio frequency signal based on the magnetic field strength to wirelessly relay the chip’s location. In conventional MRI, all of these features are intrinsically found in atoms. Ther researchers still had to create an architecture that functionally mimics them for our chip. Article from CaltechArticle edit by kynix
kynix On 2017-11-20   206
LED

New method to Improve Efficiency and brightness of Green LEDs

Article provided by University of Illinois at Urbana-ChampaignArticle edit by kynix A new methord to make Green LEDs more brighter and more efficient have been developed by researchers who at the University of lllinois at Urbana Champaign.  Researchers have created gallium nitride(GaN) cubic crystals grown on a silicon substrate that are capable of producing powerful green light for advanced solid-state lighting. "This work is very revolutionary as it paves the way for novel green wavelength emitters that can target advanced solid-state lighting on a scalable CMOS-silicon platform by exploiting the new material, cubic gallium nitride," said Can Bayram, an assistant professor of electrical and computer engineering at Illinois who first began investigating this material while at IBM T.J. Watson Research Center several years ago. "The union of solid-state lighting with sensing (e.g. detection) and networking (e.g. communication) to enable smart (i.e. responsive and adaptive) visible lighting, is further poised to revolutionize how we utilize light. And CMOS-compatible LEDs can facilitate fast, efficient, low-power, and multi-functional technology solutions with less of a footprint and at an ever more affordable device price point for these applications."  GaN was formed ethier hexagonal or cubic typically. HExagonal GaN is thermodynamically stable and is by far the more conventional form of the semiconductor. However, hexagonal GaN is prone to a phenomenon known as polarization, where an internal electric field separates the negatively charged electrons and positively charged holes, preventing them from combining, which, in turn, diminishes the light output efficiency. Until now, the only way researchers were able to make cubic GaN was to use molecular beam epitaxy, a very expensive and slow crystal growth method when compared to the widely used metal-organic chemical vapor deposition (MOCVD) method that Bayram used. Bayram and his graduate student Richard Liu made the cubic GaN by using lithography and isotropic etching to create a U-shaped groove on Si (100). This non-conducting layer essentially served as a boundary that shapes the hexagonal material into cubic form. "Our cubic GaN does not have an internal electric field that separates the charge carriers—the holes and electrons," explained Liu. "So, they can overlap and when that happens, the electrons and holes combine faster to produce light."  At the end, Bayram and Liu still believe their cubic GaN method may lead to LEDs free from the "droop" phenomenon that has plagued the LED industry for years. For LED lighting color like green, blue, or ultra-violet LEDs , their light-emission efficiency declines as more current is injected, which is characterized as "droop." "Our work suggests polarization plays an important role in the droop, pushing the electrons and holes away from each other, particularly under low-injection current densities," said Liu, who was the first author of the paper, ""Maximizing Cubic Phase Gallium Nitride Surface Coverage on Nano-patterned Silicon (100)", appearing Applied Physics Letters. Having better performing green LEDs will open up new avenues for LEDs in general solid-state lighting. For example, these LEDs will provide energy savings by generating white light through a color mixing approach. Other advanced applications include ultra-parallel LED connectivity through phosphor-free green LEDs, underwater communications, and biotechnology such as optogenetics and migraine treatment. Having better performing green LEDs will open up new avenues for LEDs in general solid-state lighting. For example, these LEDs will provide energy savings by generating white light through a color mixing approach. Other advanced applications include ultra-parallel LED connectivity through phosphor-free green LEDs, underwater communications, and biotechnology such as optogenetics and migraine treatment. 
kynix On 2017-11-10   260

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.