The Kynix Components

CatalogProduct OverviewLM75BIMM-3/NOPB Related Video IntroductionLM75BIMM-3/NOPB CAD ModelsLM75BIMM-3/NOPB Pin ConfigurationLM75BIMM-3/NOPB Functional Block DiagramLM75BIMM-3/NOPB FeaturesLM75BIMM-3/NOPB ApplicationsLM75BIMM-3/NOPB DatasheetLM75BIMM-3/NOPB SpecificationsLM75BIMM-3/NOPB ManufacturerUsing WarningLM75BIMM-3/NOPB FAQ Product OverviewThe LM75B and LM75C are industry-standard digital temperature sensors with an integrated Sigma-Delta analog-to-digital converter and 14C interface. The LM75 provides 9-bit digital temperature readings with an accuracy of +2°C from -25°C to 100°C and +3°C over- 55°C to 125°C. Communication is accomplished over a 2-wire interface which operates up to 400kHz. The LM75 has three address pins, allowing up to eight LM75 devices to operate on the same 2-wire bus. The LM75 has a dedicated over-temperature output (O.S. ) with programmable limit and hystersis. This output has programmable fault tolerance, which allows the user to define the number of consecutive error conditions that must occur before O.S. is activated. The wide temperature and supply range and I2C interface make the LM75 ideal for a number of applications including base stations, electronic test equipment, office electronics, personal computers, and any other system where thermal management is critical to performance. The LM75B and LM75C are available in an SOIC package or VSSOP package. LM75BIMM-3/NOPB Related Video IntroductionLM75BIMM-3/NOPB Video Description: Temperature sensors explained. How do temperature sensors work? In this video we learn the basics of how different temperature sensors work. We look at thermometers, thermocouples, thermistors and resistance temperature detectors RTD. LM75BIMM-3/NOPB CAD ModelsFigure: LM75BIMM-3 NOPB PCB Symbol   Figure: LM75BIMM-3 NOPB Footprint   Figure: LM75BIMM-3 NOPB 3D Models LM75BIMM-3/NOPB Pin Configuration Figure: LM75BIMM-3 NOPB Pin Configuration LM75BIMM-3/NOPB Functional Block DiagramFigure: LM75BIMM-3 NOPB Functional Block Diagram LM75BIMM-3/NOPB FeaturesNo External Components RequiredShutdown Mode to Minimize Power ConsumptionUp to Eight LM75s Can be Connected to a SingleBusPower Up Defaults Permit Stand-alone Operationas ThermostatUL Recognized Component (LM75B and LM75C)Key Specifications:- Supply Voltage- LM75B, LM75C: 3 V to5.5 V- Supply Current- Operating: 280 μA (typical)- Shutdown: 4 μA (typical)- Temperature Accuracy- 25°C to 100°C: +2°C (maximum)- 55°C to 125°C: +3°C (maximum) LM75BIMM-3/NOPB ApplicationsGeneral System Thermal ManagementCommunications InfrastructureElectronic Test EquipmentEnvironmental Monitoring Figure: LM75BIMM-3 NOPB Typical Application LM75BIMM-3/NOPB DatasheetYou can download the datasheet from the link given below:LM75BIMM-3/NOPB Datasheet LM75BIMM-3/NOPB SpecificationsProduct AttributeAttribute ValueManufacturer:Texas InstrumentsProduct Category:Board Mount Temperature SensorsOutput Type:DigitalConfiguration:LocalAccuracy:+/- 3°CSupply Voltage - Min:3 VSupply Voltage - Max:5.5 VInterface Type:2-Wire, I2C, SMBusResolution:9 bitOperating Temperature:-55°C ~ 125°CShutdown:ShutdownMounting Style:SMD/SMTPackage / Case:VSSOP-8Brand:Texas InstrumentsOperating Supply Current:280 uAOutput Current:10 uAProduct:Temperature Sensors with OvertempProduct Type:Temperature SensorsSeries:LM75BSubcategory:SensorsTemperature Threshold:ProgrammableUnit Weight:0.001101 oz LM75BIMM-3/NOPB ManufacturerTexas Instruments Incorporated (TI) is an American technology company headquartered in Dallas, Texas, that designs and manufactures semiconductors and various integrated circuits, which it sells to electronics designers and manufacturers globally. It is one of the top 10 semiconductor companies worldwide based on sales volume.The company's focus is on developing analog chips and embedded processors, which account for more than 80% of its revenue.TI also produces TI digital light processing technology and education technology products including calculators, microcontrollers and multi-core processors. The company holds 45,000 patents worldwide as of 2016. Using WarningNote: Please check their parameters and pin configuration before replacing them in your circuit. LM75BIMM-3/NOPB FAQWhat is a digital temperature sensor?A digital temperature is a sensor, which provides 9-bit temperature readings. Digital temperature sensors offer excellent precise accuracy, these are designed to read from 0°C to 70°C and it is possible to achieve ±0.5°C accuracy. These sensors completely aligned with digital temperature readings in degrees Celsius. How does a digital temperature sensor work?They are devices to measure temperature readings through electrical signals. The sensor is made up of two metals, which generate electrical voltage or resistance once it notices a change in temperature. There are many applications that are not-so-obvious, which use temperature sensors. What is temperature sensor used for?A temperature sensor is a device used to measure temperature. This can be air temperature, liquid temperature or the temperature of solid matter. There are different types of temperature sensors available and they each use different technologies and principles to take the temperature measurement. 

Product OverviewThe LT ®1014 is the first precision quad operational amplifier which directly upgrades designs in the industry standard 14-pin DIP LM324/LM348/OP-11/4156 pin configuration. It is no longer necessary to compromise specifications, while saving board space and cost, as compared to single operational amplifiers. This blog will introduce LT1014 systematically from its features, pinout to its specifications, applications, also including LT1014 datasheet and so much more. CatalogProduct OverviewLT1014 FeaturesLT1014 PinoutLT1014 Pin ConfigurationLT1014 ApplicationsLT1014 EquivalentLT1014 Circuit DiagramLT1014 Schematic DiagramLT1014 PackageLT1014 SpecificationLT1014 ManufacturerLT1014 DatasheetUsing WarningsLT1014 FAQ LT1014 FeaturesSingle Supply OperationInput Voltage Range Extends to GroundOutput Swings to Ground While Sinking CurrentPin Compatible to 1458 and 324 with Precision SpecsGuaranteed Offset Voltage: 150μV MaxGuaranteed Low Drift: 2μV/°C MaxGuaranteed Offset Current: 0.8nA MaxGuaranteed High Gain5mA Load Current: 1.5 Million Min17mA Load Current: 0.8 Million MinGuaranteed Low Supply Current: 500μA MaxLow Voltage Noise, 0.1Hz to 10Hz: 0.55μVP-PLow Current Noise—Better than 0P-07, 0.07pA/√Hz LT1014 PinoutThe following figure is the diagram of LT1014 pinout. LT1014 Pinout LT1014 Pin ConfigurationPin NoPin NameDescription1OUTPUT AOutput Of Amplifier A2INV-INPUT AInverting Input Of Amplifier A3NON-INV-INPUT ANon Inverting Input Of Amplifier A4V+Positive Power Supply5INV-INPUT BInverting Input Of Amplifier B6NON-INV-INPUT BNon Inverting Input Of Amplifier B7OUTPUT BOutput Of Amplifier B8OUTPUT COutput Of Amplifier C9INV-INPUT CInverting Input Of Amplifier C10NON-INV-INPUT CNon Inverting Input Of Amplifier C11V-Negative Power Supply12NON-INV-INPUT DNon Inverting Input Of Amplifier D13INV-INPUT DInverting Input Of Amplifier D14OUTPUT DOutput Of Amplifier D LT1014 ApplicationsBattery-Powered Precision Instrumentation Strain Gauge Signal Conditioners Thermocouple Amplifiers Instrumentation Amplifiers4mA to 20mA Current Loop TransmittersMultiple Limit Threshold DetectionActive FiltersMultiple Gain Blocks LT1014 EquivalentLM324 LT1014 Circuit DiagramThe following is the circuit diagram of LT1014. 50MHz Thermal RMS-to-DC Converter 5V Single Supply Dual Instrumentation Amplifier Hot-Wire Anemometer LT1014 Schematic DiagramThe architecture and pin configuration of LT1014 is shown in the picture below. LT1014 Schematic Diagram LT1014 PackageThe following diagram shows the LT1014 package. LT1014 Package LT1014 SpecificationManufacturer:Linear TechnologyAmplifier Type:OPERATIONAL AMPLIFIERAverage Bias Current-Max (IIB):0.038 µAInput Offset Voltage-Max:1000 µVNeg Supply Voltage Limit-Max: -22 VNeg Supply Voltage-Nom (Vsup): -15 VOperating Temperature-Max:70 °CLength:10.3 mm LT1014 ManufacturerAnalog Devices, Inc. (ADI), also known simply as Analog, is an American multinational semiconductor company specializing in data conversion, signal processing and power management technology, headquartered in Wilmington, Massachusetts. In 2012, Analog Devices led the worldwide data converter market with a 48.5% share, according to analyst firm Databeans. LT1014 DatasheetYou can download LT1014 datasheet from the link given below:LT1014 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. LT1014 FAQWhat is an Operational Amplifier?An operational amplifier is an integrated circuit that can amplify weak electric signals. An operational amplifier has two input pins and one output pin. Its basic role is to amplify and output the voltage difference between the two input pins. What is the difference between amplifier and operational amplifier?Amplifiers can be either electronic or mechanical in common definition whereas operational amplifiers are electronic amplifiers. Amplifiers, in general, have a limited capability of amplifying DC signals but all op-amps are capable of amplifying DC signals. What is bandwidth of op amp?The operational amplifiers bandwidth is the frequency range over which the voltage gain of the amplifier is above 70.7% or -3dB (where 0dB is the maximum) of its maximum output value as shown below. What is the purpose of op-amp?The fundamental function of an op-amp is to greatly amplify the differential between the two inputs, and output the result. If input at V(+) is greater than at V(−), the op-amp will amplify and output a positive signal; if V(−) is greater, the op-amp will output an amplified negative signal. Why are op-amps useful?Op-amps are still a primary building block for analog systems, performing tasks like amplification, active filtering, and signal transformation. In digital systems, op-amps are used in buffers, analog-to-digital converters, digital-to-analog converters, and regulated power supplies, to name a few applications.

CatalogFeaturesTypical ApplicationsMechanical DataPrimary CharacteristicsMaximum RatingsElectrical CharacteristicsThermal CharacteristicsOrdering InformationRatings and Characteristics Curves1N4004 PackageDisclaimer1N4004 DatasheetUsing Warnings1N4004 FAQ FeaturesLow forward voltage dropLow leakage currentHigh forward surge capabilitySolder dip 275 °C max. 10 s, per JESD 22-B106 Typical ApplicationsFor use in general purpose rectification of power supplies, inverters, converters, and freewheeling diodes application. Mechanical DataCase: DO-41 (DO-204AL), molded epoxy bodyMolding compound meets UL 94 V-0 flammability ratingBase P/N-E3 - RoHS-compliant, commercial grade Terminals: matte tin plated leads, solderable perJ-STD-002 and JESD 22-B102E3 suffix meets JESD 201 class 1A whisker test Polarity: color band denotes cathode end Primary CharacteristicsPRIMARY CHARACTERISTICSIF(AV)1.0 AVRRM50 V, 100 V, 200 V, 400 V, 600 V, 800 V, 1000 VIFSM (8.3 ms sine-wave)30 AIFSM (square wave tp = 1 ms)45 AVF1.1 VIR5.0 μATJ max.150 °CPackageDO-41 (DO-204AL)Circuit configurationSingle Maximum RatingsMAXIMUM RATINGS (TA = 25 °C unless otherwise noted)PARAMETERSYMBOL1N40011N40021N40031N40041N40051N40061N4007UNITMaximum repetitive peak reverse voltageVRRM501002004006008001000VMaximum RMS voltageVRMS3570140280420560700VMaximum DC blocking voltageVDC501002004006008001000VMaximum average forward rectified current 0.375" (9.5 mm) lead length at TA = 75 °CIF(AV)1.0APeak forward surge current 8.3 ms single half sine-wave superimposed on rated loadIFSM30ANon-repetitive peak forward surge current square waveform TA = 25 °C (fig. 3)tp = 1 ms IFSM45 A tp = 2 ms 35  tp = 5 ms 30 Maximum full load reverse current, full cycle average 0.375" (9.5 mm) lead length TL = 75 °CIR(AV)30μARating for fusing (t < 8.3 ms)I2t (1)3.7A2sOperating junction and storage temperature rangeTJ, TSTG-50 to +150°C NoteFor device using on bridge rectifier application Electrical CharacteristicsELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)PARAMETERTEST CONDITIONSSYMBOL1N40011N40021N40031N40041N40051N40061N4007UNITMaximum instantaneous forward voltage1.0 AVF1.1VMaximum DC reverse current at rated DC blocking voltage TA = 25 °C IR5.0 μA  TA = 125 °C 50 Typical junction capacitance4.0 V, 1 MHzCJ15pF Thermal CharacteristicsTHERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)PARAMETERSYMBOL1N40011N40021N40031N40041N40051N40061N4007UNIT Typical thermal resistanceRqJA (1)50 °C/W RqJL (1)25  Note(1) Thermal resistance from junction to ambient at 0.375" (9.5 mm) lead length, PCB mounted Ordering InformationORDERING INFORMATION (Example)PREFERRED P/NUNIT WEIGHT (g)PREFERRED PACKAGE CODEBASE QUANTITYDELIVERY MODE1N4004-E3/540.3354550013" diameter paper tape and reel1N4004-E3/730.33733000Ammo pack packaging Ratings and Characteristics CurvesThe followings are the figures of 1N4004 ratings and characteristics curves. Forward Current Derating Curve Maximum Non-repetitive Peak Forward Surge Current Non-Repetitive Peak Forward Surge Current Typical Junction Capacitance Typical Instantaneous Forward Characteristics Typical Transient Thermal Impedance Typical Reverse Characteristics 1N4004 PackageThe following diagram shows the 1N4004 package. 1N4004 Package DisclaimerALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 1N4004 DatasheetYou can download 1N4004 datasheet from the link given below:1N4004 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. 1N4004 FAQWhat is a Standard Rectifier?A rectifier diode lets electrical current flow in only one direction and is mainly used for power supply operation. Rectifier diodes can handle higher current flow than regular diodes and are generally used in order to change alternating current into direct current. Which type of diode is used in rectifier?For power rectification applications, power diodes or Schottky diodes are normally used. For signal rectification small point contact diodes, signal diodes, or Schottky diodes may be used. The Schottky diode has the advantage that it only requires a forward voltage of around 0.2 - 0.3volts for forward conduction. How many diodes does a rectifier have?There are four diodes in the full-wave rectifier circuit. When the AC source voltage is positive, the current flows through D1 to the load and back to the AC source via D2. What is the limitation of a diode rectifier?It needs four diodes. The circuit is not suitable when a small voltage is required to be rectified. It is because, in this case, the two diodes are connected in series and offer double voltage drop due to their internal resistance. What is the most widely used rectifier?Silicon diodes are the most widely used rectifiers for lower voltages and powers, and have largely replaced other rectifiers. 

Product OverviewSeventh Generation HEXFET® Power MOSFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per silicon area. This benefit, combined with the fast switching speed and ruggedized device design that HEXFET power MOSFETs are well known for, provides the designer with an extremely efficient and reliable device for use in a wide variety of applications. The TO-220 package is universally preferred for all commercial-industrial applications at power dissipation levels to approximately 50 watts. The low thermal resistance and low package cost of the TO-220 contribute to its wide acceptance throughout the industry. This blog will introduce IRF1404 systematically from its features, pinout to its specifications, applications, also including IRF1404 datasheet and so much more. CatalogProduct OverviewRelated Video IntroductionIRF1404 FeaturesIRF1404 PinoutIRF1404 EquivalentsIRF1404 Circuit DiagramIRF1404 PackageIRF1404 SpecificationIRF1404 ManufacturerIRF1404 DatasheetUsing WarningsIRF1404 FAQ Related Video Introduction Video: IRF1404 mosfet Inverter Circuit IRF1404 Video Description: In today's video, you will learn how to make IRF1404 mosfete Inverter  Circuit Diagram using Proteus software. IRF1404 FeaturesPlanar cell structure for wide SOA Optimized for broadest availability from distribution partnersProduct qualification according to JEDEC standardIndustry standard surface-mount power packageHigh-current ratingIncreased ruggednessMulti-vendor compatibilityIndustry standard qualification levelStandard pinout allows for drop in replacementHigh current carrying capability IRF1404 PinoutThe following figure is the diagram of IRF1404 pinout. VDSS = 40VRDS(on) = 0.004ΩID = 202A IRF1404 Pinout IRF1404 EquivalentsIRF2804IRFB3004IRFB3077IRFB3077IRFB3206IRFB3004IRFB3006IRFB3006GIRFB3004GIRFB3077 IRF1404 Circuit DiagramThe following are the circuit diagrams of IRF1404. Switching Time Test Circuit Unclamped Inductive Test Circuit  Gate Charge Test Circuit Peak Diode Recovery dv/dt Test Circuit IRF1404 PackageThe following diagram shows the IRF1404 package. IRF1404 Package IRF1404 SpecificationProduct AttributeAttribute ValueManufacturer:InfineonProduct Category:MOSFETTechnology:SiMounting Style:Through HolePackage / Case:TO-220-3Transistor Polarity:N-ChannelNumber of Channels:1 ChannelVds - Drain-Source Breakdown Voltage:40 VId - Continuous Drain Current:162 ARds On - Drain-Source Resistance:4 mOhmsVgs - Gate-Source Voltage:- 20 V, + 20 VQg - Gate Charge:160 nCMinimum Operating Temperature:- 55 CMaximum Operating Temperature:+ 175 CPd - Power Dissipation:333 WChannel Mode:EnhancementBrand:Infineon / IRConfiguration:SingleFall Time:33 nsHeight:15.65 mmLength:10 mmProduct Type:MOSFETRise Time:190 nsTransistor Type:1 N-Channel IRF1404 ManufacturerInfineon Technologies is a leading global designer, manufacturer and supplier of a broad range of semiconductors used in various microelectronic applications. Infineon's product portfolio consists of logic products, including digital, mixed-signal, and analog integrated circuits, as well as discrete semiconductor products. IRF1404 DatasheetYou can download IRF1404 datasheet from the link given below:IRF1404 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. IRF1404 FAQWhat is the difference between power Mosfet and MOSFET?Power MOSFET is a type of MOSFET which is specially meant to handle high levels of power. These exhibit high switching speed and can work much better in comparison with other normal MOSFETs in the case of low voltage levels. However its operating principle is similar to that of any other general MOSFET. What does MOSFET power mean?Power MOSFET is a type of metal oxide semiconductor field-effect transistor used to switch large amounts of current. Power MOSFETs are the most commonly used power devices due to their low gate drive power, fast switching speed and superior paralleling capability. Engineering Glossary. What are the applications of power Mosfet?Power MOSFETs are commonly used in automotive electronics, particularly as switching devices in electronic control units, and as power converters in modern electric vehicles. The insulated-gate bipolar transistor (IGBT), a hybrid MOS-bipolar transistor, is also used for a wide variety of applications. What is the disadvantage of MOSFET?Has a short life. Required repeated calibration for accurate dose measurement. They have very susceptible to overload voltage, hence due to installation special handling is to be required. What are advantages of power Mosfet?The power MOSFET is the most common power semiconductor device in the world, due to its low gate drive power, fast switching speed, easy advanced paralleling capability, wide bandwidth, ruggedness, easy drive, simple biasing, ease of application, and ease of repair.

Product OverviewThis N-Channel enhancement mode silicon gate power field effect transistor is an advanced power MOSFET designed, tested, and guaranteed to withstand a specified level of energy in the breakdown avalanche mode of operation. All of these power MOSFETs are designed for applications such as switching regulators, switching convertors, motor drivers, relay drivers, and drivers for high power bipolar switching transistors requiring high speed and low gate drive power. These types can be operated directly from integrated circuits. This blog will introduce IRFP250 systematically from its features, pinout to its specifications, applications, also including IRFP250 datasheet and so much more. CatalogProduct OverviewRelated Video IntroductionIRFP250 FeaturesIRFP250 PinoutIRFP250 ApplicationsIRFP250 EquivalentsIRFP250 Circuit DiagramIRFP250 PackageIRFP250 SpecificationIRFP250 ManufacturerIRFP250 DatasheetUsing WarningsIRFP250 FAQ Related Video Introduction Video: Power Amplifier Class D 6 Mosfets IRFP250 IRFP250 FeaturesDynamic dV/dt RatingRepetitive Avalanche RatedIsolated Central Mounting HoleFast SwitchingEase of ParallelingSimple Drive RequirementsCompliant to RoHS Directive 2002/95/EC IRFP250 PinoutThe following figure is the diagram of IRFP250 pinout.VDSS = 200VRDS(on) = 0.075ΩID = 30A IRFP250 Pinout IRFP250 ApplicationsLED flashers or dimmersLow power analog inverters or convertersSmall signal switching Switching high voltage loads  IRFP250 EquivalentsIRFP250 is an n-channel advanced power mosfet. The equivalents of IRFP250 are irfZ44, irf9Z34N, 2n7000, and bs170. Light dimmers  and speed control of the motors are good with the equals or IRFP250 because they have good switching characteristics. IRFP250 Circuit DiagramThe following is the circuit diagram of IRFP250. Switching Time Test Circuit Unclamped Inductive Test Circuit Gate Charge Test Peak Diode Recovery dV/dt Test Circuit IRFP250 PackageThe following diagram shows the IRFP250 package. IRFP250 Package IRFP250 SpecificationProduct AttributeAttribute ValueManufacturer:STMicroelectronicsProduct Category:MOSFETRoHS:NTechnology:SiMounting Style:Through HolePackage / Case:TO-247-3Transistor Polarity:N-ChannelNumber of Channels:1 ChannelVds - Drain-Source Breakdown Voltage:200 VId - Continuous Drain Current:33 ARds On - Drain-Source Resistance:85 mOhmsVgs - Gate-Source Voltage:- 20 V, + 20 VMinimum Operating Temperature:- 65 CMaximum Operating Temperature:+ 150 CPd - Power Dissipation:180 WChannel Mode:EnhancementPackaging:TubeConfiguration:SingleFall Time:40 nsHeight:20.15 mmLength:15.75 mmProduct Type:MOSFETRise Time:50 nsSeries:IRFP250Factory Pack Quantity:30 IRFP250 ManufacturerSTMicroelectronics is a global independent semiconductor company and is a leader in developing and delivering semiconductor solutions across the spectrum of microelectronics applications. An unrivaled combination of silicon and system expertise, manufacturing strength, Intellectual Property (IP) portfolio and strategic partners positions the Company at the forefront of System-on-Chip(SoC) technology and its products play a key role in enabling today's convergence trends. IRFP250 DatasheetYou can download IRFP250 datasheet from the link given below:IRFP250 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. IRFP250 FAQWhat is the difference between power Mosfet and MOSFET?Power MOSFET is a type of MOSFET which is specially meant to handle high levels of power. These exhibit high switching speed and can work much better in comparison with other normal MOSFETs in the case of low voltage levels. However its operating principle is similar to that of any other general MOSFET. What does MOSFET power mean?Power MOSFET is a type of metal oxide semiconductor field-effect transistor used to switch large amounts of current. Power MOSFETs are the most commonly used power devices due to their low gate drive power, fast switching speed and superior paralleling capability. Engineering Glossary. What are the applications of power Mosfet?Power MOSFETs are commonly used in automotive electronics, particularly as switching devices in electronic control units, and as power converters in modern electric vehicles. The insulated-gate bipolar transistor (IGBT), a hybrid MOS-bipolar transistor, is also used for a wide variety of applications. What is the disadvantage of MOSFET?Has a short life. Required repeated calibration for accurate dose measurement. They have very susceptible to overload voltage, hence due to installation special handling is to be required. What are advantages of power Mosfet?The power MOSFET is the most common power semiconductor device in the world, due to its low gate drive power, fast switching speed, easy advanced paralleling capability, wide bandwidth, ruggedness, easy drive, simple biasing, ease of application, and ease of repair.

CatalogMAX232 DescriptionMAX232 Related Video InstructionMAX232 CAD ModelsMAX232 Pin ConfigurationMAX232 Typical Operating CircuitMAX232 FeaturesMAX232 ApplicationsMAX232 DatasheetMAX232 SpecificationsMAX232 ManufacturerUsing WarningMAX232 FAQMAX232 DescriptionThe MAX220–MAX249 family of line drivers/receivers is intended for all EIA/TIA-232E and V.28/V.24 communications interfaces, particularly applications where ±12V is not available. The MAX225, MAX233, MAX235, and MAX245/MAX246/MAX247 use no external components and are recommended for applications where printed circuit board space is critical. The MAX220-MAX249 are offered in 26 different packages with temperatures from 0 to +70°C up to -55°C to +125°C. See ordering information table at the end of the data sheet for all package and temperature options. MAX232 Related Video InstructionVideo:Fundamentals of Serial Transceiver DevicesMAX232 Video Description:Learn the differences between three popular serial transceivers: RS-232, RS-422 and RS-485. This video walks through the details of each communication protocol and provides example applications. MAX232 CAD Models Figure: PCB Symbol  Figure: Footprint  Figure: 3D Model MAX232 Pin Configuration Figure: Pin Configuration MAX232 Typical Operating Circuit Figure: Typical Operating Circuit MAX232 FeaturesIntegrated Charge Pump Circuitry         - Eliminates the Need for a Bipolar ±12V Supply       - Enables Single Supply Operation from +5V SupplyIntegrated Capacitors (MAX223, MAX233, MAX235, MAX245–MAX247) Saves Power forReduced Power Requirements  5μW Shutdown Mode   MAX232 ApplicationsInterface TranslationMultidrop RS-232 NetworksPortable Diagnostics Equipment MAX232 DatasheetYou can download the datasheet from the link given below.MAX232-Datasheet MAX232 SpecificationsProduct Category:RS-232 Interface ICMounting Style:Through HolePackage / Case:PDIP-16Series:MAX232Function:TransceiverData Rate:120 kb/sNumber of Drivers:2 DriverNumber of Receivers:2 ReceiverDuplex:Full DuplexOperating Supply Voltage:5 VOperating Supply Current:10 mAMinimum Operating Temperature:0 ℃Maximum Operating Temperature:+ 70 ℃ESD Protection:Without ESD ProtectionPackaging:TubeManufacturer:Maxim IntegratedBrand:Maxim IntegratedHeight:4.45 mmLength:19.43 mmProduct:RS-232 TransceiversProduct Type:RS-232 Interface ICPropagation Delay Time:10 usShutdown:Without ShutdownFactory Pack Quantity:25Subcategory:Interface ICsSupply Type:Single SupplySupply Voltage - Max:5.5 VSupply Voltage - Min:4.5 VWidth:7.87 mmPart # Aliases:MAX232Unit Weight:0.056438 oz MAX232 ManufacturerMaxim Integrated, a subsidiary of Analog Devices, designs, manufactures, and sells analog and mixed-signal integrated circuits for the automotive, industrial, communications, consumer, and computing markets. Maxim's product portfolio includes power and battery management ICs, sensors, analog ICs, interface ICs, communications solutions, digital ICs, embedded security, and microcontrollers. The company is headquartered in San Jose, California, and has design centers, manufacturing facilities, and sales offices worldwide. Using WarningNote: Please check their parameters and pin configuration before replacing them in your circuit. MAX232 FAQWhat does an RS-232 transceiver do?An RS 232 transceiver is a type of communication device that allows data to be sent and received wirelessly. The term “RS 232” indicates a “recommended standard“ set of rules that are used by all compatible devices.This allows data to be sent wireless beyond the limited cable range. What is an RS-232 connection?Simply put, a RS232 connection transmits signals using a positive voltage for a binary 0 and a negative voltage for a binary 1.These modules can be anything that also uses RS232 such as, operator interface or HMI, computers, motor controllers or drives, a robot, or some kind of vision system. How many devices can be connected to RS-232?RS-232 is the simplest of the two interfaces. It is used to connect two devices as illustrated below: That is, the transmitter of Device 1 is connected to the receiver of Device 2 and vice versa.