Phone

    00852-6915 1330

structure Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

IC Chips

Global Semiconductor Supply Chain: How It Works From Fab to Distributor

Strategic Analysis: This data-driven guide covers the semiconductor supply chain explained for procurement managers, engineers, and business buyers navigating the severe 2026 hardware constraints.The global semiconductor supply chain is no longer a sequential manufacturing process; it is a live geopolitical auction. Big Tech hyperscalers are injecting unprecedented capital into the pipeline, effectively buying up all sub-7nm capacity and forcing lower-margin industries out. Consequently, understanding this ecosystem requires looking past basic fabrication to the critical bottlenecks in design software, raw materials, and specialized logistics. According to Goldman Sachs Research and march 2026 pmic market analysis kynix supply chain report, the top five hyperscalers (Amazon, Microsoft, Google, Meta, and Oracle) are projected to spend between $635 billion and $690 billion on capital expenditures in 2026, with approximately 75% of that budget directly targeting AI infrastructure and data centers.The Semiconductor Supply Chain Explained: The Pre-Conflict Geographic RealityThe semiconductor supply chain is geographically entrenched because advanced node manufacturing requires decades of localized infrastructure and specialized labor that cannot be rapidly replicated.Despite aggressive Western reshoring efforts and subsidies like the US CHIPS Act, the physical manufacturing center of gravity remains heavily entrenched in East Asia. In early 2026, Asia still dominates over 70% of global semiconductor manufacturing capacity. According to the TestFlow 2026 Global Chip Map and PwC Semiconductor Report 2026, South Korea (~21%), Industrial Chain and Development Trend of PCB in China (~21%), and Taiwan (~19%) control the vast majority of the physical pipeline. Building a fabrication plant in Ohio or Germany does not create immediate self-sufficiency when the raw materials and chemical processing remain centralized overseas.Pro Tip: While many guides suggest government subsidies will create domestic self-sufficiency by 2030, professional workflows actually require immediate reliance on East Asian fabs because raw material processing and sub-tier chemical suppliers remain heavily centralized there.The Shift to In-House DesignThe traditional dynamic of tech companies buying off-the-shelf chips is dead. Experts point out that "Consumer-Facing Designers" like Apple and Tesla have transitioned from being mere component buyers to operating as their own highly aggressive design houses. This shift fundamentally changes the supply chain power dynamic, as these companies now compete directly with traditional chipmakers for foundry space.The Design Layer: Fabless Architects and EDA MonopoliesThe design layer is highly monopolized because creating modern microarchitectures requires proprietary simulation software controlled by a strict oligopoly.The EDA and Design Ecosystem MonopolyBefore a physical chip is manufactured, it must be designed. The industry splits into two primary models: Fabless companies (like NVIDIA and AMD) that design chips but outsource the manufacturing, and Integrated Device Manufacturers (IDMs, like Intel) that design and manufacture their own silicon. Both models currently fight for the exact same limited foundry capacity.The "Big Three" GatekeepersBefore a single atom of silicon is etched, companies must pass through the Electronic Design Automation (EDA) layer. The EDA market is an oligopoly where just three companies—Synopsys (~31%), Cadence (~30%), and Siemens EDA (~13%)—control over 85% of the global market share, generating a combined ~$16 billion in revenue, according to SemiAnalysis and Deep Research Global (2026). In visual whiteboard breakdowns of the ecosystem, we observed that these specific EDA tools are mandatory. You cannot bypass them.Counter-Intuitive Fact: While most people think foundries hold all the power, the EDA software monopoly actually dictates the pace of innovation. Without paying millions in licensing fees to these three companies, fabless architects cannot even submit a design for manufacturing.Entity Comparison: Fabless vs. IDM vs. FoundryBusiness ModelPrimary FunctionKey Advantage2026 VulnerabilityExample EntitiesFablessArchitecture & DesignLow capital expenditure on physical plants.Completely reliant on third-party foundry capacity.NVIDIA, AMD, AppleIDMDesign & ManufacturingEnd-to-end control over the production timeline.Massive R&D costs to maintain bleeding-edge nodes.Intel, SamsungFoundryPure-Play ManufacturingEconomies of scale; serves multiple massive clients.Geopolitical risk and extreme equipment costs.TSMC, GlobalFoundriesDecision Framework: If you prioritize raw compute power for AI training, choose NVIDIA's latest architecture. If you prioritize absolute cost-efficiency for basic legacy IoT sensors, then nan is the strategic winner.The Fabrication Chokehold: Sub-7nm Nodes and The "Invisible" InfrastructureThe fabrication chokehold is severe because sub-7nm production relies on ultra-expensive lithography equipment and highly volatile chemical supply chains.2nm Silicon Wafer Detail and High-NA EUV LithographyThe EUV & Yield Rate BattleThe physical scale of transistors is the true battleground for AI. To achieve sub-7nm and 3nm nodes, foundries rely entirely on Extreme Ultraviolet (EUV) lithography. ASML's next-generation High-NA (Numerical Aperture) EUV lithography machines, which are mandatory for scaling down to 2nm and 1.4nm nodes, cost approximately $350 million to $380 million per single unit (Forbes / ASML Corporate Guidance).With a $350M EUV machine, foundries can etch transistors at the 2nm scale. This means a hyperscaler can pack 100 billion transistors into a single GPU, allowing a data center to train a massive language model in weeks rather than years. However, the ultimate metric of foundry success is the Yield Rate—the percentage of working chips on a silicon wafer. Complex metallization stacks frequently fail, making high yield rates the most closely guarded secret in the industry.The Unsung Vacuum Pump BottleneckVisual stress tests and industry breakdowns highlight critical sub-tier suppliers that are rarely mentioned. Vacuum pump suppliers like Edwards, DAS, and Pfeiffer provide the ultra-high vacuum environments without which semiconductor fabrication is physically impossible. Furthermore, the ecosystem is not a linear chain but a complex network. If the materials layer (companies like Resonac or Merck) fails to provide specific, highly volatile chemicals, the entire multi-billion dollar fabrication process stops.OSAT and Specialized Logistics: The Final Points of FailureOSAT and logistics are critical failure points because they act as strict quality gates and require highly specialized, time-sensitive handling.OSAT as a Strict Quality GateOutsourced Semiconductor Assembly and Test (OSAT) is the final, often overlooked packaging bottleneck. Real-world testing suggests that assembly and testing aren't just for packaging; they are strict quality gates. If a batch doesn't meet specifications and quality standards at the OSAT stage, the entire previous fabrication cost is written off as a total loss.THE SEMICONDUCTOR SUPPLY CHAIN - A BRIEF OVERVIEWCritical LogisticsExperts point out that logistics serve as a single point of failure. Beginners often forget that these chips are time-sensitive, high-value assets. The industry relies on specialized courier networks, specifically naming Airspace and CNW, to move highly sensitive wafers securely across global zones.Pro Tip: While standard freight focuses on volume, semiconductor logistics prioritize vibration control and temperature stability. A single turbulent flight without proper dampening can destroy millions of dollars in completed integrated circuits.Is Physical Manufacturing Capacity the Actual Ceiling for AI Advancement Right Now?Physical manufacturing capacity is the current ceiling because hyperscaler demand vastly outpaces the foundries' ability to scale advanced node production.To appease insatiable AI demand from companies like NVIDIA and Apple, TSMC is being forced to boost its 3nm monthly wafer capacity to 180,000–200,000 wafers by the end of 2026—a 20% to 40% increase over their initial targets, according to TrendForce and Global Semi Research. Even with this massive expansion, the capacity is immediately consumed by the highest bidders.The Tungsten & Rare Earth FactorUsers on community forums often report extreme frustration that consumer PC components and lower-margin automotive industries are getting squeezed out of fab capacity. This is the "Collapse of Normal Tech." AI giants are willing to pay massive premiums, effectively monopolizing the top-tier supply chain. Furthermore, critical raw materials like tungsten are emerging as brand-new strategic bottlenecks, heavily influenced by quiet geopolitical repositioning ahead of potential global conflicts.As noted in industry analyses, "Overall, the semiconductor manufacturing ecosystem is a complex and interdependent network of Semiconductor Systems or Components that work together to bring new semiconductor products to market."Conclusion & Strategic Next StepsThe semiconductor supply chain is a highly contested network because AI infrastructure investments have fundamentally altered global procurement priorities.The 2026 semiconductor landscape is defined by the hyperscaler squeeze. The supply chain is working exactly as designed—but only for the top 1% of buyers who can afford to monopolize TSMC's 3nm nodes and ASML's High-NA EUV machines. As industry experts note, "There are thousands and thousands of companies involved," meaning resilience requires deep visibility into sub-tier suppliers, from EDA software monopolies to vacuum pump manufacturers.Procurement teams must audit their tier-2 and tier-3 component reliance today. Securing alternative supply lines for critical chemicals and legacy nodes is mandatory before competitors secure the remaining global capacity.FAQ: People Also AskWhat is the difference between a Foundry and an OSAT?A foundry (like TSMC) physically manufactures the silicon wafers and etches the microscopic transistors onto them. An OSAT (Outsourced Semiconductor Assembly and Test) takes those completed wafers, cuts them into individual chips, tests them for quality, and packages them into the final protective casing used in electronics.Why are EUV lithography machines so important?Extreme Ultraviolet (EUV) lithography machines, exclusively manufactured by ASML, use light with a wavelength of just 13.5 nanometers to print incredibly tiny, complex patterns on silicon. They are the only machines on Earth capable of producing the advanced sub-7nm chips required for modern AI, smartphones, and supercomputers.What does a 3nm node mean in semiconductor manufacturing?Historically, "3nm" referred to the physical gate length of a transistor. Today, it is a commercial marketing term used to denote a specific generation of highly advanced, densely packed microarchitecture. A 3nm node offers significantly higher performance and lower power consumption compared to previous generations like 5nm or 7nm.How are hyperscalers impacting the global chip shortage?Hyperscalers (Amazon, Google, Microsoft, Meta) are investing hundreds of billions into AI data centers. Because they require the most advanced chips (like NVIDIA GPUs) and are willing to pay massive premiums, they consume the vast majority of top-tier foundry capacity, leaving lower-margin industries (like auto and consumer electronics) fighting for limited remaining resources.Why can't the US or Europe just build their own independent supply chains?Building a physical fabrication plant is only one piece of the puzzle. An independent supply chain requires domestic control over raw materials (rare earths, tungsten), specialized chemicals, EDA software, and sub-tier infrastructure (vacuum pumps, specialized logistics). Currently, this ecosystem is deeply entangled globally, with critical dependencies firmly rooted in East Asia and Europe.
Kynix On 2026-07-27   168
IC Chips

Detailed Analysis of Flexible Electronics Materials and Applications

  After 20 years, your life may be like this:The electronic skin on your pulse can monitor your heart rate and blood sugar at any time to realize intelligent pulse detection;The electronic skin on your throat can "voice" for the deaf and mute by feeling the pressure changes produced by the movement of the throat muscles;Your whole body may become a network center, and the sensors in your body will connect with the outside world...All this seems very far away, but these technologies are quietly gestating, and are very likely to become disruptors of new technologies.Flexible Electronics: The Future of TECHNow is the era of smart phones, but the current smart electronic products are still rigid electronic devices. In the future, mankind is about to enter a new era, the era of flexible electronics. Flexible electronic devices that are as soft as human skin will be the next development trend of the electronics industry, and may even subvert human life. Catalog I What is Flexible electronics?II Applications of flexible electronics2.1 Flexible electronic display2.2 Thin film solar panels2.3 RFID2.4 Electronic skinIII ConclusionFAQ  I What is Flexible electronics? The concept of flexible electronics started in the 1980s, when people tried to replace inorganic semiconductors such as silicon with organic semiconductors, so that organic electronic devices have flexible characteristics.Flexible electronic technology is a brand-new electronic technology revolution. It is an emerging electronic technology that makes organic and inorganic materials electronic devices on flexible, malleable plastic or thin metal substrates. It has a wide range of fields in information, energy, medical treatment, and national defense.  Applications of flexible electronics In addition to integrating electronic circuits, functional materials, micro-nano manufacturing and other fields of technology, flexible electronic technology also spans industries such as semiconductors, packaging, testing, materials, chemicals, printed circuits, and display panels. Not only that, it can also help the transformation and upgrading of traditional industries, such as plastics, printing, chemicals, and metal materials.By improving its performance and industrial added value, flexible electronics will frequently appear in human life, bringing revolutionary changes to the industrial structure and future life. As technology upgrades, flexible electronics materials research and development and rich application products have emerged.II Applications of flexible electronicsWith the development of flexible electronic technology, various electronic products have emerged. Just as microelectronics technology provides a technology platform for large-scale integrated circuits and computer chip technologies, flexible electronic technology provides a brand-new technological platform for the research and development of new products. 2.1 Flexible electronic displayThe flexible electronic display is a brand-new product developed on the flexible electronic technology platform. Unlike traditional flat-panel displays, such displays can be repeatedly bent and folded, thus bringing great convenience to our lives.For example, all visual materials, including books, newspapers, magazines, and video files, can be presented on this display and can be viewed anytime, anywhere. Although current popular MP4 players and personal digital assistants (PDAs) can meet such use needs, the display screen cannot be bent and folded, and can only be read and viewed in a small screen area. And video, visual effects are greatly constrained. In contrast, flexible electronic displays have unparalleled advantages. They are like newspapers. When they are needed, they are unfolded. When they are used, they are curled or even folded. This guarantees the convenience of portability while giving full consideration to the visual effects.Flexible electronic displaySamples of flexible electronic displays have been successfully developed and it is believed that it will be a long way from entering the market. It is worth mentioning that flexible electronic displays use more lightweight organic materials instead of inorganic materials, so their weight is lighter than traditional displays, and this feature helps to improve their portability. In addition, the use of high molecular organic materials offers possibilities for reducing costs. In addition, the flexible electronic display has the characteristics of a thin thickness, and its thickness can be much smaller than that of the popular liquid crystal display. Therefore, another name of the flexible electronic display is a paper-like electronic display.2.2 Thin film solar panelsThin film solar panel is another specific application of flexible electronics technology. In today's world, energy has become a topic of global concern. China not only faces energy shortages but also faces environmental pollution. As a clean energy source, solar energy can effectively alleviate the contradiction of energy shortage under the premise of zero environmental pollution.As the most common way to use solar energy, solar panels can cover a large area at the lowest cost to effectively use solar energy. At present, thin film amorphous Sili-Con solar panels have been successfully developed and marketed. Thin film solar panel Thin-film solar panels based on flexible electronic technology can meet high-power generation needs, such as the use of thin-film solar panels in solar power plants in sunny desert areas.In addition, it can also make full use of its flexible and lightweight features to integrate it into clothing. Putting on such clothes to walk or exercise in the sun, the power of small appliances (such as MP3 players and laptops) that are carried around can be supplied by the thin-film solar panels on the clothes, thus achieving the purpose of saving and environmental protection.2.3 RFIDRadio frequency identification (RFID) technology can be used to complete information input and processing, fast and convenient operation, and rapid development without manual contact, and is widely used in production, logistics, transportation, medical, food, security and other fields. RFID systems usually consist of transponders and readers.The electronic tag is one of many forms of transponder, and can be understood as a transponder with a thin film structure, which has the characteristics of convenient use, small size, thin and light, and can be embedded in the product. More and more electronic tags will be used in future RFID systems.Flexible Electronics in RFIDIn this response to Covid-19, flexible electronic technology has played a huge role in body temperature measurement.Group body temperature measurement has problems such as huge number of monitoring people, cumbersome temperature measurement work, and difficulty in continuous temperature recording. Wearable temperature measuring stickers made by introducing flexible electronic technology can record and analyze the body temperature data of the target population. In this way, potential threats can be discovered and eliminated through long-term monitoring, thereby helping management departments to achieve personnel management monitoring.2.4 Electronic skinAnother important application of flexible electronics is electronic skin. Electronic skin, also called skin-like electrons, is basically characterized in that various electronic components are integrated on a flexible substrate to form a skin-like circuit board, which has high flexibility and elasticity like skin and can be used in many other applications. electrical equipment.It can be said that the potential of flexible electronic skin is great. With the popularization of technologies such as smart medical care, virtual reality, and artificial intelligence, the demand for wearable devices has surged, and flexible electronic skin is a perfect combination of wearable devices. Think about an electronic component installed on the body and used as a skin, isn't it sci-fi?Electronic skinIII Conclusion Folding computers, folding mobile phones, and wearable digital products are in the ascendant. With the development of science and technology, flexible electronic devices have received more and more attention from the society. Such devices can still work under bending, folding, twisting, compression or stretching conditions. In the future, flexible electronic equipment will have a very broad development space in the fields of energy, medical, information and communication.Pieces of work brought by flexible electronics are interpreting the integration of innovation and tradition in the era of the Internet of Everything, and the era of science and technology connecting everything is approaching.You can boldly imagine that in 20 years, your life might be like this:In the morning, the flexible electronic skin watch on your body wakes you up and reports the quality of your sleep. Put on your glasses, and the day’s schedule has been displayed for you on the transparent screen. After washing, the robot has prepared breakfast for you and your family; After going out, the smart watch on your wrist shows that the air quality is excellent; the smart assistant called "Flying" for you and has parked outside the house, waiting for you to start your day's itinerary... FAQ 1. Why are electronics flexible?The key advantages of flexible electronics, compared with current silicon technologies, are low-cost manufacturing (e.g. ink-jet printing and roll-to-roll imprinting) and inexpensive flexible substrates (e.g. plastics). ... In principle, flexible electronics is ideal for integration. 2. Where are flexible electronics used?Consumer electronics devices make use of flexible circuits in cameras, personal entertainment devices, calculators, or exercise monitors. Flexible circuits are found in industrial and medical devices where many interconnections are required in a compact package. 3. How could Flexible Electronics benefit the consumer?Among the benefits of flexible electronics (compared to traditional, rigid alternatives) are size, weight, portability, and energy efficiency. Above all, they make previously impossible designs and technologies (such as wearable devices) possible. 4. When was flexible electronics invented?1960s. Flexible electronics have a long history. The first flexible device was made in the 1960s by thinning crystalline silicon solar cells for use in extraterrestrial satellites. Today, smart credit cards carry bendable microchips which are made using stretchable Silicon. 5. What are flexible electronics made of?Flexible Electronics: generally refers to a class of electronic devices built on conformable or stretchable substrates, usually plastic, but also metal foil, paper and flex glass. 6. What are the two major approaches of making flexible electronics?(1) Transfer and bonding of completed circuits to a flexible substrate(2) Fabrication of the circuits directly on the flexible substrate  7. What makes flexible electronic display attractive?One property of flexible electronics which deserves to be highlighted is their robustness. This makes a great difference for applications such as wearables, notebooks and other consumer electronics which traditionally feature glass-based displays or sensors. 8. How flexible electronics are made?Compared with conventional microelectronics, flexible electronics does not require extrinsic packages such as ceramics. Instead, flexible circuits and packages can be manufactured and integrated together using only plastics. ... These layers can then be stacked together to complete the flexible electronic systems. 9. Why are flexible electronics important?Among the benefits of flexible electronics (compared to traditional, rigid alternatives) are size, weight, portability, and energy efficiency. Above all, they make previously impossible designs and technologies (such as wearable devices) possible. 10. Why do we need flexible materials?Not only does flexible packaging use less material than its rigid counterparts, leading to a lower overall packaging cost, it also creates less waste. Fres-co states that flexible packaging formats create 50 percent less waste than rigid ones, while also reducing greenhouse gas emissions and BTU consumption. 
Kynix On 2025-04-29   946
Robots

Securing the Future of Electric Vehicles - Addressing Cybersecurity Threats

Overview: This article discusses cybersecurity's importance for electric vehicles and their charging infrastructure, highlighting vulnerabilities and protective measures against cyberattacks.   Electric vehicles (EVs) have developed into one of the key technologies to help society meet challenging clean energy and decarbonization goals over the past ten years. The electric vehicle market has expanded by 60% annually on average. In the near future, this growth is anticipated to continue with even higher adoption rates. Electric Vehicle Advantages Many nations have implemented policies to promote the use of clean-fuel vehicles. The main obstacle to the adoption of electric vehicles is frequently identified as range anxiety. Recent advancements in battery and charging technology are reducing this range anxiety. For instance, the 100 kWh battery in the Tesla Model S is enough for a trip of up to 402 miles.    Similarly, electric vehicle charging stations and the infrastructure that supports them have grown significantly in size and number. At the end of the year, there were 7.3 million electric vehicle charging stations implemented worldwide, an increase of 60% from the previous year. Additionally, the electric vehicle charging stations now have a higher charging capacity and can provide faster charging services. These electric vehicle charging stations with a rated charging power of up to 350 kW have been recently developed. An electric vehicle can be charged using these chargers in under 15 minutes.   Smart electric vehicle charging features like remote control through smartphone apps are not only making electric vehicle charging faster but also more approachable and, therefore, more available to broader customer audiences.   Cyberattacks in Electric Vehicles Although significant and well-publicized cyberattacks have not yet targeted smart electric vehicle charging stations, threats and reasonable ways of attack have been reported. According to Kaspersky Lab, ChargePoint Home's smartphone electric vehicle charging app has security flaws. Through the charging device's WiFi connection, this flaw would allow a remote attacker to break into the charger and interfere with electric vehicle charging.    Cyberattacks might also target electric vehicle charging station web applications, such as those from Circontrol, an electric vehicle charging station vendor with over 80,000 electric vehicle charging stations in 60 nations. This flaw would make use of the poor login information for electric vehicle charging. These well-known vulnerabilities highlight the cyber risks associated with electric vehicles and electric vehicle charging stations. Protective Measures Against these Cyberattacks Because of these attacks and the social costs they produce, efforts are being made to standardize cyber-physical interfaces for both residential and commercial electric vehicle charging.    Electric vehicles and electric vehicle charging stations are vulnerable to attacks that could harm equipment due to non-standard cyber-physical interfaces. For a number of electric vehicle charging architectures, the European Network on Cybersecurity suggested security standards. These standards provide security for both electric vehicle charging stations and their possessions. It also secures communications between charging station operators and power grid operators.    The standard specifies access control, future security compatibility of charging stations, monitoring and controlling system security, and message encryption for secure communication. Additionally, due to flaws in these interfaces, it is possible to weaponize electric vehicles and use them to launch extensive demand-side cyberattacks against the power grid.    Demand-side cyberattacks on electricity grids involve manipulating appliances like electric vehicles, distributed energy resources, and heating, ventilation, and air conditioning (HVAC) loads. These appliances are internet-connected and have high power. Although such attacks on power grids have not occurred in the past, there is growing awareness among electric vehicle owners that they could be carried out using vulnerabilities that already exist. Power grid operators won't be able to handle them.  Smart Grids Cybersecurity A cyber-physical overview of the smart electric power grid is shown in Fig. 1. Resources that are IoT-enabled are still being used in all four power sectors, including generation, transmission, distribution, and customer service. However, by utilizing IoT-enabled devices, it also introduces new cyber threats to the power grid. An overview of these threats as they relate to smart grid cybersecurity can be found below. Fig. 1: A cyber-physical overview of the smart electric power grid Source: IEEE Access Stride Threat Model The STRIDE threat model, originally created by Microsoft to assess software threats, can be used to categorize cyberattacks. It is a categorical risk assessment model for spoofing, tampering, repudiation, integrity, denial-of-service (DoS), and elevation of privilege threats to a given cyber-physical system. Smart Grid Threats SCADA Threats SCADA is a centralized monitoring and control system that is frequently used in real-world power grids. It has four main parts: a central master terminal unit, a human-machine interface (HMI), field units like power line communications (PLC), remote terminal units (RTU), and communication channels. Despite having industry-standard defenses, the SCADA network is still susceptible to insider attacks.   SCADA Field Unit Threats Intelligent electronic devices (IEDs), PLCs, RTUs, and phasor measurement units (PMUs) are examples of SCADA field units. Relays, sensors, and breakers are examples of microprocessor-based IEDs. IEDs are monitored by RTUs, which send measurements to PLCs, SCADAs, or both. PLCs and SCADAs, in turn, use RTUs to communicate control signals to IEDs. This control capability of PLCs enables some control actions to be performed decentralized without involving SCADA.   The field units communicate with one another by using protocols. Additionally, these protocols are open to online threats. The system can become unstable if erroneous data is introduced into it.   Advanced Metering Infrastructure (AMI) Threats To allow interaction between the utility, consumers, and distributed energy resources (DERs), power grids are increasingly deploying AMI, such as smart meters. Residential consumers or prosumers may have IoT-enabled devices like smartphones linked to the exact same network as their smart meter, while commercial DER operators plan to protect their smart meter-connected network with a VPN. Smart meters and their communication channels are vulnerable to all types of cyberattacks because of this attack surface.   Demand Response Threats Demand response resources make use of AMIs and Smart meters, making them equally susceptible to threats. The data input and output of these devices can be manipulated causing problems to the grid operators.   Threats from Devices With IoT Intruders can get into high-wattage devices and appliances with IoT interfaces by taking advantage of weak passwords on local networks and the fact that they can connect to remote devices like smartphones and smart TVs, which are vulnerable to supply chain threats.    Electric Vehicle Charging Threats Cyberattacks on charging electric vehicles and the power grid pose greater social and economic risks. The charging methods can be wired charging or wireless charging, but the risks possessed are the same.   Summarizing the Key Points Cybersecurity is crucial for the growing electric vehicle industry and its charging infrastructure to prevent potential cyberattacks.Standardizing cyber-physical interfaces and implementing security measures are essential to protect electric vehicles and charging stations.Vulnerabilities in electric vehicle charging systems can be exploited, posing risks to equipment and potentially impacting power grids.The European Network on Cybersecurity has suggested security standards to safeguard communication between charging station operators and power grid operators.The rapid growth of electric vehicles and charging infrastructure necessitates a proactive approach to address cybersecurity challenges and ensure a secure and sustainable future. References [1] Acharya Samrat, Yury Dvorkin, Hrvoje Pandzic, and Ramesh Karri. “Cybersecurity of Smart Electric Vehicle Charging: A Power Grid Perspective.” IEEE Access 8 (2020): 214434–53. https://doi.org/10.1109/access.2020.3041074.
Rakesh Kumar, Ph.D. On 2023-06-20   163
Power

Commercial Electric Vehicles Charging Infrastructure

Overview: The availability of charging infrastructure is the most critical factor in the market penetration of commercial electric vehicles. In this article, a concise evaluation of a variety of topics related to the development of such infrastructure is provided.Charging InfrastructureThe SAE J1772 standard categorizes the electric vehicle (EV) charging infrastructure into three levels based on the charging power rate, voltage, current, and installation location, as shown in Table 1. Levels 1 and 2 are known as slow chargers, while level 3 is a fast charger. These levels indicate how long EVs take to charge.Table 1. Charging Levels of EV According to the SAE J1772 Standard. Source: IEEE Accessi The standard of North America.ii Typical values of DC charging station.iii Developed DC charging station. By the end of 2018, there were roughly 5.2 million light-duty vehicles (electric truck) charging stations installed worldwide. While public charging stations reached 1,44,000 fast chargers and 3,95,000 slow chargers, the majority of these stations were installed as slow-charging private stations. Numerous plans to accelerate the deployment of charging infrastructure were also announced. The majority of these announcements concerned chargers from the private sector with various capacities. Other announcements deal with publicly accessible chargers and make fewer promises for infrastructure for charging on highways. The power needs of these vehicles determine whether the current charging infrastructure is appropriate for commercial EVs (CEVs). Light- and medium-duty (electric trucks) ETs can be charged overnight using level 2 chargers, while small- and medium-duty ETs can be charged quickly using level 3 chargers. Additionally, some heavy-duty ETs can be overnight charged using level 3 chargers.  However, the majority of medium- and heavy-duty EVs with long driving distances need specialized fast-charging infrastructure with higher power capacities than the current fast level 3 chargers. As a result, several businesses, including Tritium, Phoenix Contact, BMW Group, and Charge Point, have revealed new plans to install high-power capacity charging infrastructure with a 400 kW or higher rating. Additionally, Tesla Inc. has revealed plans to expand its network of 1 MW mega chargers, each of which can travel 640 km in just 30 minutes. In accordance with the operational schedules of commercial EVs, charging infrastructure can be installed at locations where vehicles are parked (depots, yards, aggregators, etc.) to enable overnight charging or between shifts, as well as in open areas to enable charging along a commercial vehicle's daily route. Two proposed methods for charging commercial EVs are suitable: return-to-base model charging infrastructure and public charging infrastructure. Return-To-Base Model Charging Infrastructure The majority of commercial enterprises use a "return-to-base" strategy, where high-power charging infrastructure is installed at their commercial facilities (depots, yards, industrial micro-grids, etc.) to enable the full charging of electric trucks (ET) outside of working hours, such as overnight or between shifts, as shown in Fig. 1. This is due to the spatial and temporal distribution of commercial truck fleet activities and a lack of suitable public charging stations.  Installing a dedicated charging station for each ET that needs to be charged at the commercial facility is the easiest strategy to implement during the early stages of ET adoption. However, it is possible for several ETs to share a single charging station in order to lower the upfront cost of the infrastructure necessary for charging, provided that this decrease in the number of charging stations does not interfere with the ETs' operational schedules.Fig. 1. Operation model of the return-to-base strategy. Source: IEEE Access Charging at Public Charging Infrastructure Commercial vehicles should ideally be charged where they park, but for a variety of reasons, as shown in Fig. 2, it may still be necessary to charge them while they are on the road during their daily driving cycles. Particularly for small commercial enterprises, charging commercial vehicles while they are on the road can help to reduce the capital cost investment of charging infrastructure required at a parking area. The development of contact-free charging infrastructure, mainly inductive power transfer (IPT) charging systems, has been the subject of extensive research.  Installation of battery swapping charging infrastructure, which allows EVs to swap out their nearly empty battery bank for a fully charged battery bank, is another way to put electric vehicles on the road. Contrarily, conductive charging stations can be gradually sized and scaled up to meet the power needs of CEVs. Therefore, compared to other options, charging stations do not require as much infrastructure investment.Fig. 2. Operation model of public charging infrastructure. Source: IEEE Access Charging Infrastructure for Long-Haul Commercial EVs Large battery banks need to be charged at warehouses because long-distance commercial vehicles have large daily ranges. The payload ratings of long-haul vehicles, however, would be impacted by the weight of the large battery banks. For a few long-haul CEVs that are currently on the market, Table 2 displays the battery weight ratio of the total GVW. As can be seen, increasing battery capacity will result in a higher battery weight to gross vehicle weight ratio, which will lower the maximum payload capability.  According to an analysis, the maximum payload of long-distance CEVs is lower than that of commercial diesel vehicles, as shown in Fig. 3. This graph displays the weight distribution of the major parts for CEVs and diesel vehicles with various battery capacities. As can be seen, compared to diesel vehicles, the CEV's maximum payload is limited to a maximum of 23%.Table 2. The battery weight ratio of the total GVW of some long-haul CEVs. Source: IEEE Accessi The battery weight is calculated based on the energy density 0.125 kWh/kgFig. 3. Weight breakdown of main components for diesel vehicles and CEVs with different battery capacities. Source: IEEE Access In order to electrify long-distance commercial vehicles, the best possible combination of battery bank size and high-power public charging stations along a route is required. Due to the strict operational schedules of these vehicles, charging long-haul vehicles on the road presents numerous difficulties. The number of hours that long-haul vehicles may be operated each day before being required to take a break is subject to many regulations.  For instance, the Federal Motor Carrier Safety Administration, a division of the US Department of Transportation, sets a daily cap on the number of hours of service at 10.5 hours before requiring eight hours of rest. Similarly to this, driving is only permitted for a maximum of 4.5 hours per day and must be followed by a minimum of a 45-minute break. Therefore, as shown in Fig. 4, charging activities for long-distance vehicles must take place when the vehicle is at rest. To keep up with their operational schedules, long-distance vehicles will have to stop at places with lots of high-power charging stations. However, running multiple chargers simultaneously imposes significant challenges on the power grid, requiring expensive network reinforcement. Additionally, the stability of a grid system is impacted by these numerous charging stations, particularly during peak hours. These limitations have an effect on the number of vehicles that can be charged at a particular location and, consequently, the rate at which charging infrastructure is utilized. Fig. 4. Operation model of haulage trucks. Source: IEEE Access The right size and localization of charging infrastructure along highway routes will be necessary to overcome the aforementioned difficulties with charging long-haul vehicles. Electric utilities, fleet owners, and truck stops should work together to identify the best locations for the charging infrastructure while taking into account the reliability of the power systems and the schedules of long-haul vehicles.Summarizing with Key Points: Some of the takeaways from the article are as follows: SAE J1772 standard divides EV charging infrastructure into three levels based on power rate, voltage, current, and installation location. Levels 1 and 2 are slow chargers, while Level 3 is a fast charger.Tritium, Phoenix Contact, BMW Group, and Charge Point have announced plans to install 400 kW or higher charging infrastructure. Tesla Inc. plans to expand its 1 MW mega charger network, which can travel 640 km in 30 minutes.There are two suggested ways to charge commercial EVs: infrastructure for Return-to-base model charging and infrastructure for public charging.Return-to-base strategy is installing high-power charging infrastructure at their commercial facilities (depots, yards, industrial micro-grids, etc.) to fully charge ETs and reduce infrastructure costs. Several ETs can share a charging station.In public charging infrastructure, road charging commercial vehicles reduces parking area charging infrastructure capital costs. IPT charging systems, battery swapping infrastructure, and conductive charging stations have been studied.To charge long-haul vehicles, highway charging infrastructure must be properly sized and located. Electric utilities, fleet owners, and truck stops should consider power system reliability and long-haul vehicle schedules when choosing charging locations. This blog post is part of a full research article from IEEE Access.
Rakesh Kumar, Ph.D. On 2023-02-28   419
Mosfets

Difference and Relation Between IGBTs and MOSFETs

Introduction IGBT and MOSFET are fully controlled devices and are voltage-driven, that is, the device is turned on or off by controlling the gate voltage. In fact, the structure of the IGBT is an NPN-type MOSFET plus a P-junction, that is, an NPNP structure, which is a P-type BJT driven by MOS in principle. So what is the difference between them? What is the specific connection of them? MOSFET BJT or IGBT - Brief Comparison Catalog Introduction Ⅰ MOSFET & IGBT Review Ⅱ Si IGBT vs SiC MOSFET Ⅲ Different Requirements for Si IGBT and SiC MOSFET 3.1 ON & OFF State 3.2 Short-Circuit Protection 3.3 Interference and Delay Ⅳ IGBT Working Principle by Analogy with MOSFET Ⅴ FAQ Ⅰ MOSFET & IGBT Review MOSFET is a metal-oxide-semiconductor field effect transistor, or metal-insulator-semiconductor. The source and drain of it can be swapped, and they are both N-type regions formed in the P-type backgate. In most cases, these two regions are the same, even if the two ends are reversed, it will not affect the performance of the device. Such devices are considered symmetrical. According to the polarity of its "channel" (working carrier), MOSFET can be divided into two types: N-type and P-type, usually also called NMOSFET and PMOSFET, abbreviations including NMOS, PMOS, etc.IGBT (insulated gate bipolar transistor), is a composite fully controlled voltage-driven power semiconductor device composed of BJT (bipolar transistor) and MOS. Have the advantages of high input impedance of MOSFET and the low on-voltage drop of the GTR. When the GTR saturation voltage is reduced, the current carrying density is large, but the driving current is large; the MOSFET driving power is small, the switching speed is fast, but the on-state voltage drop is large, and the current carrying density is small. The IGBT combines the advantages of the above two devices, and the driving power is small and the saturation voltage is reduced. In simple terms, an IGBT is equivalent to a thick base PNP transistor driven by a MOS. Figure 1. N-MOSFET Architecture Ⅱ Si IGBT vs SiC MOSFET Since the differences between IGBT and MOSFET in structure, working principle and application range are quite detailed, it is impossible to express clearly in one sentence. Next, we will compare the differences between silicon (Si) IGBTs and silicon carbide (SiC) MOSFETs in detail.The electrical parameters and characteristics of Si IGBT and SiC MOS drivers are quite different. The requirements for driving of SiC MOS are also different from those of traditional silicon devices. They have the characteristics of low on-resistance and small switching loss, which can reduce device loss and improve system efficiency, and more suitable for high frequency circuits. It is widely used in new energy vehicle motor controller, vehicle power supply, solar inverter, charging pile, UPS, PFC power supply and other fields.The difference between the two is mainly reflected in the GS turn-on voltage, GS turn-off voltage, short-circuit protection, signal delay and anti-interference, as follows: Characteristic Si IGBT SiC MOSFET Drive Requirements Switching Frequency Low, >30kHz High, 50~500kHz 1) Use high power gate resistors. 2) Optimize the cooling environment. 3) Improve the efficiency of the DC-DC conversion circuit and reduce the overall loss of driving power. Threshold Voltage 5V-6V 1.6V-4.5V Negative pressure shutdown/Miller clamp to prevent false turn-on Switching Time 300ns 50ns 1) Use digital isolation driver chip, the signal transmission delay can reach 50ns, and it has relatively high consistency, and the transmission jitter is less than 5ns. 2) the low transmission delay push-pull chip is selected. Switching-On Time 15V 15V~22V 1) Priority is given to stabilizing the negative voltage to ensure that the shutdown voltage is stable. 2) A negative voltage clamping circuit is added to ensure that it does not exceed the standard during shutdown. Switching-Off voltage -15V~-5V -5V~0V Short-Circuit Withstand Time <10μs 2~5μs A diode or a resistor string is used to detect short circuits, and the shortest short-circuit protection time is limited to about 1.5μs. CMTI 15kV/μs 100kV/μs 1) The common mode anti-interference ability reaches 100kV/μs to transmit the isolation chip for signal transmission. 2) The optimized isolation transformer design is adopted, and its primary side and the secondary side are shielded to reduce mutual crosstalk. 3) The Miller clamp is used to prevent the influence of the switch of the same bridge arm.   Ⅲ Different Requirements for Si IGBT and SiC MOSFET For a fully-controlled switching device, configuring an appropriate on-off voltage is of great significance for the safety and reliability of the device. Due to the difference between IGBT and MOSFET, the requirements for the two are also different.IGBT is a field-controlled device whose turn-on and turn-off are determined by the voltage between the gate(G) and the emitter(E). The working principle of MOS tube (enhancement mode NMOSFET) is to use VGS to control the amount of "induced charges" to change the condition of the conductive channel, and then to control the drain current. 3.1 ON & OFF State 1) Silicon IGBT: Silicon IGBTs of various manufacturers have the same turn-on and turn-off voltage requirements.· The typical turn-on voltage is required to be 15V.· The shutdown voltage value range is -5V~-15V, and customers can choose the appropriate value according to their needs. The common values are -8V, -10V, -15V.· Prioritize stable positive voltage to ensure stable turn-on.2) Silicon carbide MOSFET: Different manufacturers have different switching voltage requirements:· The turn-on voltage is required to be higher than 22V~15V.· The shutdown voltage is required to be higher -5V~-3V.· Prioritize negative voltage stabilization to ensure stable turn-off voltage.· Increase the negative voltage clamping circuit to ensure that it does not exceed the standard when it is turned off. 3.2 Short-Circuit Protection The switching device has the risk of short circuit during operation, and configuring a suitable short circuit protection circuit can effectively reduce the damage caused by the short circuit during the use of the switching device. Compared to Si IGBTs, SiC MOSFETs have shorter short-circuit withstand times.1) Silicon IGBTThe time of surrender and short-circuit of Si IGBT is generally less than 10μs. When designing the short-circuit protection circuit of it, set the detection delay and corresponding time of short-circuit protection to 5-8μs.2) SiC MOSFETGenerally, the short-circuit withstand capability of SiC MOSFET modules is less than 5μs, and short-circuit protection is required to work within 3μs. A diode or a resistor string is used to detect short circuits, and the protection time is limited to about 1.5μs. 3.3 Interference and Delay 1) The impact of high dv/dt and di/dt on the system.When the switching action is performed under the condition of high voltage and high current, the switching of the silicon carbide MOSFET device will generate high dv/dt and di/dt, which will affect the driver circuit. It is very important to improve the anti-interference ability of the driver circuit for the reliable operation of the system. the following way to achieve.· Add common mode choke coil and filter inductor to the input power supply, which reduce the interference of driver EMI to low voltage power supply.· A low-pass filter is added to the rectification part of the secondary side power supply, which reduce the interference of the driver to the high-voltage side.· Use an isolation chip with a common mode immunity of 100kV/μs for signal transmission.· Optimize the isolation transformer design, and use shielding layer on primary side and secondary side to reduce crosstalk between each other.· Use Miller clamp to prevent the influence of the switch of the same bridge arm. 2) Low transmission delayUsually, the application switching frequency of silicon IGBT is less than 40kHZ, and the recommended application switching frequency of SiC MOSFET is greater than 100kHz. The increase of application frequency makes MOS require the driver to provide lower signal delay time. The transmission delay of the SiC MOSFET drive signal should be less than 200ns, and the transmission delay jitter should be less than 20ns, which can be achieved by the following methods.· Using digital isolation driver chip, the signal transmission delay can reach 50ns, and it has relatively high consistency, and the transmission jitter is less than 5ns.· Select push-pull chips with low transmission delay and short rise & fall time. Due to the conductance modulation effect, the on-state specific resistance of high voltage SiC IGBTs is much lower than that of power SiC MOSs, and does not change much as the blocking voltage rating increases. When the conductance modulation effect is fully exerted, the on-state voltage drop of the IGBT drift region is only related to the bipolar diffusion coefficient and bipolar lifetime of the carriers, and will not change with the increase of the on-current. When the operating temperature changes, the on-state voltage drop of the SiC high voltage IGBT decreases with the increase of the junction temperature. This is mainly because the bipolar lifetime of the extra carriers in the SiC epitaxial layer will increase with the increase of temperature. Although the diffusion coefficient will shrink to some extent with the increase of temperature, the greater prolongation of lifetime will eventually make the the bipolar diffusion length increased, thereby reducing the on-state voltage drop. It is especially true in n-channel devices.This is in sharp contrast to the larger increase in the forward voltage drop of the power MOS at high temperature. Silicon carbide p-channel IGBTs have higher on-state voltage drop than n-channel IGBTs at the same current density due to their larger channel resistance, but their volt-ampere characteristics do not change much with temperature. As for the applications, this is undoubtedly an advantage. Figure 2. Comparison of characteristics between SiC IGBT and power MOS under the Same Condition of Withstand Voltage of 20kV. It is not difficult to calculate from the intersection of the equal power consumption curve in the figure and the on-state characteristic curves of these devices: corresponding to the same power consumption of 300W/cm2, the ratio of the on-state current of the silicon carbide IGBT to the silicon carbide power MOS versus p-channel devices and n-channel devices are different, they are 1.5 and 1.8 at room temperature, respectively, and increase to 2.7 and 3.5 at 225°C, indicating that high-voltage and high-current SiC IGBTs are more suitable for high-temperature applications.In a word, compared with Si IGBT, SiC MOSFET not only improves system efficiency, power density and operating temperature, but also puts forward higher requirements for the driver. In order to make silicon carbide MOSFET better in the system, it is necessary to give SiC MOSFET a appropriate driver.   Ⅳ IGBT Working Principle by Analogy with MOSFET IGBT is a Darlington pair composed of GTR and MOSFET: part of which is MOSFET driver, and the other part is thick-base PNP transistor. Figure 3. IGBT Architecture Its simplified equivalent circuit is shown in the figure below, and RN in the figure is the modulation resistance in the base area of the PNP transistor. It can be clearly seen from this circuit that the IGBT is a composite device of Darlington configuration composed of transistors and MOSFET, where the transistor in the figure is a PNP transistor, and the MOSFET is an N-channel field effect transistor, so the IGBT of this structure is called an N-channel IGBT, and its symbol is N-IGBT. Similarly there are P-channel IGBTs, namely P-IGBTs. Figure 4. Simplified Equivalent Circuit The electrical graphic symbols of the IGBT are shown in the figure. IGBT is a field-controlled device, and its turn-on and turn-off are determined by the voltage UGE between the gate and the emitter. When the gate-emitter voltage UCE is positive and greater than the turn-on voltage UCE (th), a channel is formed in the MOSFET and is a PNP. The N-type transistor provides the base current to turn on the IGBT. At this time, the holes (minority carriers) injected into the N- region from the P+ region modulate the conductance of the N- region, reduce the resistance RN of the N- region, and make the IGBT also has a small on-state voltage drop. When no signal or reverse voltage is applied between the gate and emitter, the channel in the MOSFET disappears, the base current of the PNP transistor is cut off, and the IGBT is turned off. It can be seen that the driving principle of IGBT is basically the same as that of MOSFET.① When UCE is negative: J3 junction is in reverse bias state, and the device is in reverse blocking state.② When UCE is positive: UC< UTH, the channel cannot be formed, and the device is in a forward blocking state; UG> UTH, an N-channel is formed under the insulating gate, and conductance is generated in the N- region due to the interaction of carriers modulation so that the device is conducting forward. Figure 5. Hybrid Switch Using Si IGBT and SiC MOSFET 1) ONThe structure of IGBT silicon is very similar to that of power MOSFET, and the main difference is that JGBT adds a P+ substrate and an N+ buffer layer, in terms of it, one MOS drives two bipolar devices (devices with two polarities). The application of the substrate creates a J junction between the P, and N+ regions of the tube. When the positive gate bias causes the inversion of the P base region under the gate, an N-channel is formed, and an electron flow occurs at the same time, and a current is generated exactly in the manner of a power MOSFET. If the voltage produced by this electron flow is in the range of 0.7V, J1 will be forward biased, some holes will be injected into the N- region, and the resistivity between N- and N+ will be adjusted, which reduces the power conduction the total loss of the pass and initiates a second charge flow. The end result is the temporary emergence of two different current topologies within the semiconductor layer: an electron flow (MOSFET current), and a hole current (bipolar). When UCE is greater than the turn-on voltage UCE(th), a channel is formed in the MOSFET to provide base current for the transistor, and the IGBT is turned on. 2) On-State Voltage DropThe conductance modulation effect reduces the resistance RN and reduces the on-state voltage drop. The so-called on-state voltage drop refers to the tube voltage drop UDS when the IGBT enters the on-state, and this voltage decreases with the rise of UCS. 3) Shut DownWhen a negative bias is applied to the gate or the gate voltage is lower than the threshold value, the channel is disabled and no holes are injected into the N-region. In any case, if the current of the MOSFET decreases rapidly during the switching phase, the collector current decreases gradually. This is because there are still minority carriers in the N layer after the commutation starts. This reduction in residual current value (wake) is entirely dependent on the charge density at turn-off, which in turn is related to several factors, such as the number and topology of dopants, layer thickness and temperature. The decay of minority carriers makes the collector current have a wake waveform. Collector current will cause increased power dissipation and cross-conduction problems, especially on devices that use freewheeling diodes.Considering that the wake is related to the recombination of minority carriers, the current value of the wake should be closely related to the Tc, IC of the chip, and has a close relationship with the mobility of holes. Therefore, depending on the temperature reached, it is feasible to reduce the undesirable effects of this current on the end equipment design. When a back pressure or no signal is applied between the gate and the emitter, the channel in the MOS disappears, the base current of the transistor is cut off, and the IGBT is turned off. 4) Reverse BlockingWhen a reverse voltage is applied to the collector, the junction is reverse biased and the depletion layer expands to the N-region. Because the thickness of this layer is reduced too much, an effective blocking ability will not be obtained, so this mechanism is very important. In addition, if the size of this region is increased too much, the voltage drop will continuously increase. 5) Forward BlockingWhen the gate and emitter are shorted and a positive voltage is applied at the collector terminal, the junction is controlled by the reverse voltage. At this time, the depletion layer of the N drift region is still subjected to the externally applied voltage. 6) LatchICBT has a parasitic PNPN thyristor between the collector and the emitter. Under special conditions, this parasitic device will turn on. This phenomenon increases the amount of current between the collector and the emitter, reduces the controllability of the equivalent MOSFET, and often causes device breakdown problems. The thyristor turn-on phenomenon is known as IGBT latch-up. Specifically, the causes of such defects vary, but are closely related to the state of the devices.   Ⅴ FAQ 1. Are there SiC IGBT?Along with the increasing maturity for the material and process of the wide bandgap semiconductor silicon carbide (SiC), the insulated gate bipolar transistor (IGBT) representing the top level of power devices could be fabricated by SiC successfully. 2. Where are SiC MOSFETs used?The primary automotive applications for SiC power MOSFETs, diodes, and modules are onboard electric vehicle (EV) chargers, DC/DC converters, and drivetrain inverters. Plug-in hybrid EVs and battery EVs (BEVs) use onboard chargers to “refuel” the vehicle battery either at home or at a public charging station. 3. What is SiC MOSFET?Silicon Carbide (SiC) MOSFETs exhibit higher blocking voltage, lower on state resistance and higher thermal conductivity than their silicon counterparts. SiC MOSFETs are designed and essentially processed the same way as silicon MOSFETs. 4. Can MOSFET replace IGBT?Due to the higher usable current density of IGBTs, it can usually handle two to three times more current than a typical MOSFET it replaces. This means that a single IGBT device can replace multiple MOSFETs in parallel operation or any of the super-large single power MOSFETs that are available today. 5. What are the advantages of silicon carbide?Silicon carbide MOSFETs have a critical breakdown strength that is 10x of silicon, and silicon carbide MOSFETs can operate at much higher temperatures, provide higher current density, experience reduced switching losses, and support higher switching frequencies. 6. What are the advantages of silicon carbide (SiC) over silicon (Si)?The advantage of SiC starts in the material itself having a 10x higher dielectric breakdown field strength, 2x higher electron saturation velocity, 3x higher energy bad gap and 3x higher thermal conductivity than Silicon. 7. What is the difference between silicon and silicon carbide?Silicon has a breakdown voltage of around 600V, while silicon carbide can withstand voltages 5-10 times higher. ... Silicon carbide can switch at nearly ten times the rate of silicon, which results in smaller control circuitry. 8. What is SiC in semiconductor?SiC (silicon carbide) is a compound semiconductor composed of silicon and carbide. SiC provides a number of advantages over silicon, including 10x the breakdown electric field strength, 3x the band gap, and enabling a wider range of p- and n-type control required for device construction. 9. Which is better MOSFET or IGBT?When compared to the IGBT, a power MOSFET has the advantages of higher commutation speed and greater efficiency during operation at low voltages. What's more, it can sustain a high blocking voltage and maintain a high current. ... The IGBT is also a three terminal (gate, collector, and emitter) full-controlled switch. 10. Why use an IGBT instead of a MOSFET?The main advantages of IGBT over a Power MOSFET and a BJT are: 1. It has a very low on-state voltage drop due to conductivity modulation and has superior on-state current density. ... It canbe easily controlled as compared to current controlled devices (thyristor, BJT) in high voltage and high current applications. 11. Why is MOSFET preferred?Mosfet provides a very good isolation between the gate and the other two terminals compared to bjt. Mosfet can handle more power compared to BJT. The mosfet has a very low power loss and a high speed. Voltage signals can easily operate a mosfet, so it is used in many digital circuits. 12. Where are MOSFETs used?Power MOSFETs are commonly used in automotive electronics, particularly as switching devices in electronic control units, and as power converters in modern electric vehicles. The insulated-gate bipolar transistor (IGBT), a hybrid MOS-bipolar transistor, is also used for a wide variety of applications. 13. Why IGBT is very popular nowadays?With its lower on-state resistance and conduction losses as well as its ability to switch high voltages at high frequencies without damage makes the Insulated Gate Bipolar Transistor ideal for driving inductive loads such as coil windings, electromagnets and DC motors. 14. How many terminals are in a MOSFET?four terminalsThe MOSFET has four terminals: drain, source, gate, and body or substrate. 15. Why is IGBT bipolar?IGBTs is a bipolar device that utilizes two types of carriers, electrons and holes, resulting from the complex configuration that features a MOSFET structure at the input block and bipolar output, making it a transistor that can achieve low saturation voltage (similar to low ON resistance MOSFETs) with relatively fast. 16. How many types of IGBT are there?two typesInsulated Gate Bipolar Junction Transistor (IGBTs) are normally classified into two types. (ii) Punch Through [PT-IGBT]. These IGBTs are also referred to as symmetrical and asymmetrical IGBTs. These varieties of IGBT differ widely with regard to their fabrication technology, structural details etc. 17. What is full MOSFET?MOSFET stands for metal-oxide-semiconductor field-effect transistor. It is a field-effect transistor with a MOS structure. Typically, the MOSFET is a three-terminal device with gate (G), drain (D) and source (S) terminals. 18. How does an IGBT work as a switch?As defined by being a transistor, an IGBT is a semiconductor with three terminals which work as a switch for moving electrical current. Just as the word “gate” suggests, when voltage is applied to the gate, it opens or “turns on” and creates a path for current to flow between the layers. 19. Can I use transistor instead of MOSFET?It very much depends on the application. BJTs can be cheaper than FETs. This is especially true for high voltage switching where the much larger die area of FETs make them much more expensive. 20. Can IGBT conduct in reverse direction?No. The IGBT cannot conduct current in the reverse direction (from emitter to collector) even with a positive Vge applied to it, because it has a bipolar-type structure. ... However, the gate has no control over this reverse current flow; it is simply the forward biasing of the diode that allows it.
Ivy On 2022-01-28   2217
Connectors

Automotive Connectors Basic and Performance Standards Overview

Introduction Automotive connectors are a component that very common for electronic engineering technicians. Its function is very simple: it sets up a bridge of communication between the blocked or isolated circuits in the circuit, so that the current flows and the circuit realizes the predetermined function. The form and structure of automotive connectors are ever-changing. They are mainly composed of four basic structural components, namely: contacts, shells (depending on the types), insulators, and accessories. Common Automotive Electrical Connections Catalog Introduction Ⅰ Automotive Connectors Ⅱ Basic Structure Ⅲ Design Criteria Ⅳ Automotive Connector Development Trends Ⅴ Connector Selection Ⅵ Performance Standard for Automotive Electrical Connectors Ⅶ FAQ Ⅰ Automotive Connectors There are nearly 100 types of connectors used in general automobiles, and there are hundreds of connectors used in a single model. As people have higher and higher requirements for safety, environmental protection, comfort, and intelligence in automobiles, the application of automotive electronic products is increasing, which make the number of automotive connector applications increase. Figure 1. Automotive Connector Type Ⅱ Basic Structure The four basic structural components of automotive connectors, it is these four basic structural components that enable automotive connectors to act as a bridge to make cars run stably.First, the contact piece is the core part of the automobile connector to complete the electrical connection function. Generally, a contact pair is composed of a male contact piece and a female contact piece, because the electrical connection is completed by the insertion of two parts.The male contact is a rigid part, and its shape is cylindrical (round pin), square column (square pin) or flat (insert). The male contacts are generally made of brass and phosphor bronze. The female contact piece is the jack, which is the key part of the contact pair. It relies on the elastic structure to elastically deform when it is inserted into the pin to generate elastic force to form close contact with the male contact piece to complete the connection. There are many types of jack structures, including cylindrical type (split slot, necking), tuning fork type, cantilever beam type (longitudinal slotting), folding type (longitudinal slotting), box type (square jack) and hyperboloid wire spring jacks, etc.Second, the shell, is the outer cover of the automotive connector. It provides mechanical protection for the built-in insulating mounting plate and pins, and provides alignment when the plug and socket are inserted, thereby fixing the connector to the device.Third, insulators, are also often referred to as automobile connector bases or inserts. Its function is to arrange the contacts according to the required position and spacing, and to ensure the insulation performance with the shell. Good insulation resistance, withstand voltage performance and ease of processing are the basic requirements for selecting insulating materials to be processed into insulators.Fourth, accessories, are divided into the structural part and the installation part. Structural accessories such as retaining rings, positioning keys, positioning pins, guide pins, coupling rings, cable clamps, sealing rings, gaskets, etc. Mounting accessories such as screws, nuts, spring rings, etc. Most of the accessories have standard parts and general parts.   Ⅲ Design Criteria With the rapid development of the automobile industry, various functional parts and various components on the automobile are constantly developing in the direction of intelligence, refinement and reliability. The structural design, appearance design and material of automobile connectors are also proposed. higher requirement. Automotive connectors must meet the USCAR-20 standard, which is the performance standard of automotive electrical connector systems. It is necessary to stipulate that the electrical connector contact surface of automotive connectors should always be reliable throughout the service cycle, including the following factors:1) The material of the connector contacts is stable and reliable.2) Positive force stability.3) The voltage and current of the circuit are stable.4) The temperature requirements are within the specified range, including the surrounding temperature and its own temperature rise.5) Better robustness.6) It must be the same as the connector used for high-speed and long-distance communication computers, and the automotive connector must be able to work reliably under harsh conditions.7) Connector insertion force: below 20.5kg8) Connector retention force: 2.5kg or more9) Heat resistance: -40~120℃ Figure 2. Automotive Connectors Ⅳ Automotive Connector Development Trends The "Miniaturization", "High Speed" and "Intelligence" of connector products are the trends of future development. The future technological innovation of the industry is mainly concentrated in the following directions:1) Miniaturization DevelopmentThis technology is mainly developed for the miniaturization trend of connectors, and can be applied to micro-miniature connectors below 0.3mm, which belongs to the new varieties of MINI USB series products. It can be used for multi-contact expansion card slot connectors, which can meet and exceed the strict requirements of multi-contact surface mount technology butt joint coplanarity, with high accuracy and low cost.2) Wireless TransmissionThe high-frequency and high-speed wireless transmission of connector technology is mainly aimed at a variety of wireless device communication applications and has a wide range of applications.3) Simulation Application TechnologyIt is based on a variety of disciplines and theories, using computer and its corresponding software such as AutoCAD, Pro/E program stress analysis software as tools, through the establishment of product models and corresponding boundary conditions, to its mechanical, electrical, high-frequency simulation analysis and confirmation of other performances, thereby reducing the cost of product development failure caused by factors such as material selection and unreasonable structure, improving the development success rate, and helping to provide support for the realization of complex system applications for products.4) Connector Intelligence TechnologyThis technology is currently mainly used in DC series power connector products. Intelligent signal detection can be performed before power transmission to ensure that the positive and negative poles are turned on and the power is turned on after the plug is inserted in place. In the future, enterprises will need to develop similar intelligent technologies for other products because of the adverse consequences of arc damage and burn-in caused by conductive contact.5) Precision connector technologyPrecision connectors involve many aspects such as product design, process technology and quality control technology. The main technologies include the following aspects:a. Precision mold processing technology: Adopt CAD, CAM and other technologies, introduce high-precision processing equipment in the industry, and use personnel production experience and advanced equipment and technical means to achieve high-precision high-quality mold products.b. Precision stamping and injection molding technology: realize precise, efficient and stable all-round control and perfect surface quality of various stamping parts and injection molding parts to ensure product quality.c. Automated assembly technology: Through the application of precision control technology, semi-automatic testing machine technology, etc., the problem of manual operation of precision products is overcome and the core competitiveness is improved.6) Manufacturing Process ResearchThe competitiveness of products depends to a certain extent on the level of manufacturing technology. Continuously developing new manufacturing processes and improving existing production and processing technologies can greatly improve the manufacturing efficiency and quality assurance capabilities of products.a. Fine manufacturing process: This process is mainly aimed at technologies such as small spacing and thin thickness. Some companies have carried out research on the process of connectors with a spacing of less than 0.4mm. This type of technology can ensure that the company reaches the advanced level of the international industry in the field of ultra-fine manufacturing.b. Integrate development technology of light source signal and electromechanical structure. It can be applied to audio connectors placed in electronic components. By adding IC, LED and other electronic components to the audio connectors, which can also transmit analog signals and the function of digital signal. It breaks through the current design of audio connector conduction transmission in the form of mechanical contact.c. Low temperature and low pressure molding process technology. The sealing and physical and chemical properties of the hot-melt material are used to achieve the functions of insulation and temperature resistance. After packaging, the wire protects the welding point from being pulled by external forces, and the packaging of the DC connector body and the wire has a insulation, temperature resistance, impact resistance and other functions ensure product quality and reliability, and will continue to be developed and applied in different products in the future. Figure 3. Automotive Connectors Ⅴ Connector Selection 1) Electrical FactorCurrent requirements: high current, low current, signal level; Steady state, cyclic, transient.They determine the type of terminal/size of contact segment/plating (0.64mm to 8.0mm pin and male terminal).Wire diameter/insulation requirements: voltage drop and/or corrosion resistance, which determine the center distance of the connector.2) Location/EnvironmentTemperature: Engine compartment – sealed, ambient temperature >105℃; vibration, fluid compatibility, passenger compartment – unsealed, ambient temperature <85℃.Sealing: Potential for high pressure jet/splash, potential for immersion, humidity; fluid type, sealed or not for device connectors.3) StandardStandards: Customer StandardsInstitutional StandardsDomestic StandardsInternational StandardsConnector performance test requirements are included in system-level specifications. For GM, Ford and Chrysler are usually USCAR specifications, that is, engine-related applications have relatively high vibration requirements. Other OEMs generally have their own standards (similar to USCAR). What’s more, equipment-side suppliers are responsible for the performance of mating-side connectors.4) Customer PreferencePreferred product strategy: Reduce cost of connector systems with different methods:Ford: Design competition for door connectors.Ford: Prefer terminal design/supplier (focus on contact interface).General: Prefer the terminal design (focus on the hole position of the connector).Chrysler: Strategies for favoring terminal/plastic Part suppliers.5) Regional preferenceNorth America: USCAR Drawing/Performance/Design Criteria —Tangless Terminals, TPA, CPA regulations. In many instances the harness supplier has a significant influence.Europe: Design influence of contact contacts/development with major OEMs; preference for two-piece contacts, even if cost pressures and North American porting operations force OEMs to consider U.S technology, that is, accepting Tangled contacts. Long-term relationships between OEMs and suppliers.Asia: Traditionally influenced by Toyota. Focus on assembly ability (ergonomics) that affects quality assurance; North America influences China to change the status, like low-cost solutions.6) Physical factorsSize, number of circuits, mating position, wire harness docking or equipment connection, mechanical main features: levers, bolts; manual docking capability; multiple types of connectors for high input/output applications.7) AssemblyWire Harness: Insertion force of connectorVisual, audible and tactile operational feedback for users. Figure 4. Terminals & Connectors Ⅵ Performance Standard for Automotive Electrical Connectors For a connector, the specification parameters such as the ambient temperature, current carrying capacity, protection level, anti-vibration level, etc. will be defined in its specifications at the beginning of research and development, because when the connector is selected according to different requirements. The following are three most widely used standards USCAR-2-6, QC/T1067-2017 and GMW3191-2012.🔺QC/T-1067 Temperature Classification Class Ambient Operating Temperature Typical Installation Position A -40~85℃ Passenger compartment (Not recommended) B -40~100℃ Passenger compartment C -40~125℃ On engine D -40~150℃ On engine (hot locations) E -40~175℃ and above Negotiate   🔺QC/T-1067 Vibration Classification Class Typical Installation Position V1 On elastic parts of the body but not to the engine V2 On engine but not to heavily vibrating parts V3 Components subject to serve vibration V4 Components subject to extreme vibration V5 On Wheel   🔺QC/T-1067 Sealing Classification Class Description Typical Installation Position S1 Unsealed Passenger compartment or trunk S2 Sealed Exposed areas S3 Sealed (with high pressure spray) Exposed areas (with high pressure spray)   🔶GMW-3191 Temperature Class Class Ambient Operating Temperature Typical Installation Position 1 -40~85℃ Passenger compartment or trunk 2 -40~100℃ Underhood, chassis 3 -40~125℃ On engine, transmission 4 -40~150℃ On engine (hot locations) 5 Per connector CTS Per CTS GTS=Component Technical Specification   🔶GMW-3191 Vibration Class Class Typical Installation Position 1 On body or chassis 2 On engine 3 On wheel, Unsprung Mass 4 Severe applications (e.g., ECU, Throttle Body, EGR) 5 Transmission (internal and external) ECU=Engine Control Unit, EGR=Exhaust Gas Recirculation   🔶GMW-3191 Sealing Class Class Description Typical Installation Position 1 Unsealed Unsealed Passenger Compartment or trunk 2 Submersion Sealed Underhood or exposed areas, including door 3 High Pressure Spray Protected Exposed areas where high pressure spray is expected   🔻USCAR-2 Temperature Classification Class Ambient Operating Temperature Typical Application T1 -40~85℃ T1 is not recommended for new applications T2 -40~100℃ Typical suitable for use in passenger component T3 -40~125℃ Typical suitable for use in engine component T4 -40~150℃ Needed for some on-engine applications near hot components T5 -40~175℃ For use as needed   🔻USCAR-2 Vibration Classification Class Common Name Typical Application Other Requirements Met V1 Chassis Profile Components on sprung portions of vehiele not coupled to Engine None V2 Engine Profile Components coupled to Engine with no severe vibration possible Pass on V2 - pass also for V1 V3 Severe On-Engine Components subject to serve vibration Pass on V3 - pass also for V1 and V2 V4 Extreme Vibration Used as needed to correlate to extreme vibration areas Pass on V4 - pass also for V1 and V2 and V3 V5 Unsprung Component Wheel-mounted components None   🔻USCAR-2 Sealing Classification Seal Class Common Name Typical Application S1 Unsealed S1 is suitable for use in passenger components or other dry areas on a vehicle such as the trunk S2 Sealed S2 (meets requirements of 5.9.7) is for exposed locations S3 Sealed (with high pressure spray) S3 is for exposed locations. It meets Sections 5.9.7 plus 5.6.7; S3 is applications when robustness to direct splash is needed Regarding the vibration test, the main purpose is to check whether the performance of the connector system under the simulated actual vehicle vibration conditions meets the requirements. In the case of vibration or in shock, it will cause the coating wear of the terminal contact surface, the positive pressure attenuation, the failure of the mechanical system performance of the supporting plastic material, etc. Therefore, it is necessary to continuously monitor the contact resistance in the vibration experiment and ensure that it does not exceed 7Ω (or 1Ω) in the line for more than 1 microsecond. According to the definition and analysis of the connector using environment through the above different standards, it is necessary to understand that the use position, the temperature level, vibration level, and protection level should be considered to make the best choice.   Ⅶ FAQ 1. What are connectors in cars?Connectors used in automotive applications enable everything from stereo systems to drivetrains. As these systems become more connected, more automated, and more energy-efficient, they require connectors that can deliver high-speed connectivity in rugged, lightweight, and easy-to-install designs. 2. How do I choose a car connector?There are several criteria to consider when selecting electrical interconnect components, including:Current rating (current density)Connector size (circuit density)Engagement forceWire sizeConfiguration and circuit sizeOperating voltageAgency approvalsPrice per circuit 3. What are the different types of automotive electrical connectors?Automotive TerminalsContactsCrimp Wire Pins, Tabs & FerrulesFoil TerminalsInterconnect DevicesKnife DisconnectsMagnet Wire TerminalsPCB Terminals 4. How many connectors does a car have?Today, there are an average of 274 connectors in a vehicle. 5. Are all car stereo connectors the same?All aftermarket car stereos can use the same car stereo wiring harness, but it all depends on what the owner of the vehicle wants to do for one main reason. 6. What is uscar standard?SAE USCAR-2. May 1, 2004. PERFORMANCE STANDARD FOR AUTOMOTIVE ELECTRICAL CONNECTOR SYSTEMS. Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and so on.
kynix On 2022-01-11   3697

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.