The Kynix Blog

IntroductionThe 1N4007 is a general-purpose silicon rectifier diode, typically found in a plastic DO-41 axial package. It is widely used in various AC-to-DC rectifier circuits, bridge rectifier circuits, and general-purpose power supply applications. The 1N4007 utilizes the unidirectional conductivity of the P-N junction to convert alternating current into pulsed direct current. Due to its high reverse voltage rating (1000V) and low cost, it is one of the most popular components in electronics.Ⅰ 1N4007 Diode Specifications1.1 Rectifier Diode OverviewThe 1N4007 is a standard recovery rectifier diode. In low-power/low-current scenarios, the forward voltage (Vf) is typically around 0.7V to 0.8V. However, under its full rated load (1A), the forward voltage drop can reach up to 1.1V.Note on Frequency: The reverse recovery time (Trr) of the 1N4007 is in the microsecond (μs) range (typically 2μs to 30μs depending on conditions). This classifies it as a "slow" diode, meaning it is suitable for 50Hz/60Hz mains rectification but not suitable for high-frequency switching circuits (like high-frequency DC-DC converters), where Fast Recovery (FR) or Ultra-Fast (UF) diodes are required.Rectifier diodes make full use of unidirectional conductivity. They block the negative half-cycle of an AC waveform to convert it into a pulsating DC signal. To smooth this output, they are usually used in combination with a capacitor. The diode is connected in series, and the capacitor is connected in parallel to the load.Figure 1. 1N4007 Bridge Rectifier Circuit Example1.2 Nomenclature: What does 1N4007 mean?"1": Represents the number of junctions. In JEDEC nomenclature, "1" stands for a component with one P-N junction (a diode)."N": Stands for semiconductor device, registered with the EIA (Electronic Industries Alliance) / JEDEC."4007": The specific registration number indicating the device's electrical characteristics within the 1N400x series.1.3 1N4007 Pins and SymbolPINDescription1 (Marked with Band)Cathode (-)2 (Unmarked)Anode (+)1.4 1N4007 Basic Parameters (at 25°C)Type: Standard Recovery Silicon RectifierMax Average Forward Rectified Current (Io): 1.0 APeak Forward Surge Current (Ifsm): 30 A (for 8.3ms single half-sine-wave)Max Repetitive Peak Reverse Voltage (Vrrm): 1000 VMax DC Blocking Voltage: 1000 VMax Forward Voltage Drop (Vf): 1.1 V (at 1.0A current)Max Reverse Leakage Current (Ir): 5 μA (at rated DC blocking voltage)Typical Junction Capacitance (Cj): 15 pF (measured at 4V, 1MHz)Typical Thermal Resistance: 65 °C/W (Junction to Ambient)Operating Temperature Range: -55°C to +150°CFigure 2. Forward Current Derating Curve1.5 1N4007 FeaturesLow reverse leakage currentHigh surge current capability (up to 30A non-repetitive)RoHS compliant and available in Pb-Free packagesHigh-temperature soldering guaranteed: 260°C/10 seconds.Mechanical Data:Case: DO-41 Molded PlasticTerminals: Plated axial leads, solderable per MIL-STD-202Polarity: Color band denotes cathode endⅡ 1N4001-1N4007 Series ComparisonThe 1N400x series contains diodes that are physically identical and rated for the same current (1A). The only difference is the Maximum Repetitive Reverse Voltage (Vrrm). Because the 1N4007 has the highest voltage rating (1000V), it can replace any other diode in the series (1N4001 through 1N4006).ModelCurrent (A)Max Peak Reverse Voltage (V)Max RMS Voltage (V)1N4001150351N40021100701N400312001401N400414002801N400516004201N400618005601N400711000700Ⅲ Alternative Models & EquivalentsThe 1N4007 can often be replaced by higher-spec diodes.Higher Current: 1N5399 (1.5A) and 1N5408 (3.0A). Note: The 1N5408 has thicker leads and a larger body (DO-201AD) and may not fit all PCB holes designed for the 1N4007.Fast Recovery: If high-frequency performance is required, FR107 (Fast Recovery) or UF4007 (Ultra Fast) are excellent replacements. They share the same voltage/current ratings but switch off much faster.Schottky Diodes (Caution): While Schottky diodes like 1N5819 or 1N5818 have a lower forward voltage drop (higher efficiency), they usually have much lower reverse voltage ratings (often 20V-40V). Do not replace a 1N4007 with a Schottky diode in high-voltage circuits (like 110V/220V mains) or the diode will fail instantly. However, for low voltage (e.g., 12V) DC inputs, a Schottky like the SB1100 (100V) can be a more efficient substitute.ModelMax Reverse Voltage (V)Avg Rectified Current (A)Max Surge Current (A)Max Reverse Leakage (μA)1N4007100013051N539910001.55051N5408100032005FR10710001305 (Fast Recovery)Ⅳ 1N4007 vs. M7 (SMD Versions)When moving from Through-Hole Technology (THT) to Surface Mount Technology (SMT), the electrical equivalents of the 1N4007 are identified by different package codes.1N4007: This specifically refers to the DO-41 axial lead package (through-hole).M7: This is the SMA (DO-214AC) surface mount version of the 1N4007. It is electrically identical (1A, 1000V).A7: This is the SOD-123 surface mount version. It is smaller than the SMA package but carries similar specs (usually slightly lower thermal dissipation).SM4007: This generally refers to the MELF (DO-213AB) cylindrical surface mount package, though "SM4007" is sometimes used generically for any SMD version.Figure 3. DO-41 Package (1N4007)Summary: If you see a diode marked "M7" on a circuit board, it is a surface-mount 1N4007.Ⅴ 1N4007 Application Examples5.1 Solving Auxiliary Winding OvervoltageThe slow recovery characteristics of the 1N4007 can sometimes be advantageous over faster diodes in specific power supply applications.In Flyback power supplies, multi-output transformers can suffer from poor cross-regulation. A common issue is the VCC auxiliary winding voltage rising too high, triggering the IC's Over-Voltage Protection (OVP). This often happens because a fast diode (like the HER107) rectifies the high-frequency leakage inductance spike (the "ringing") at the leading edge of the waveform, rather than just the plateau voltage.Figure 4. IC Control CircuitSolution: By replacing the fast HER107 with a standard speed 1N4007, the slower turn-on time ignores the initial high-frequency spike. This effectively filters the peak voltage, lowering the average VCC voltage seen by the IC and preventing false OVP triggering.5.2 RCD Snubber EMI SuppressionIn RCD (Resistor-Capacitor-Diode) snubber circuits used to protect MOSFETs in Flyback converters, using a slow diode like the 1N4007 can help improve Electro-Magnetic Interference (EMI).Figure 5. RCD Absorption CircuitHow it works: A "fast" diode snaps off very quickly, which can induce high-frequency ringing. The 1N4007 takes longer to recover (reverse recovery). During this brief recovery period, a small amount of reverse current flows back. This "soft recovery" acts as a dampener, absorbing some of the oscillation energy and reducing the voltage stress and EMI radiation on the MOSFET drain.Trade-off: The downside is that the 1N4007 will generate more heat due to reverse recovery losses. This technique is generally suitable for lower-power adapters (<20W) where EMI is a priority and thermal overhead is available.Ⅵ FAQ1. What is a 1N4007 diode used for?It is a general-purpose rectifier diode used to convert AC to DC, prevent reverse polarity, and protect circuits from voltage spikes (flyback protection).2. What is the difference between 1N4001 and 1N4007?The only difference is the Peak Repetitive Reverse Voltage. The 1N4001 is rated for 50V, while the 1N4007 is rated for 1000V. 1N4007 can replace a 1N4001, but a 1N4001 cannot replace a 1N4007 in high-voltage circuits.3. Can I replace 1N4148 with 1N4007?Generally, No. The 1N4148 is a high-speed signal diode (very fast switching, low current). The 1N4007 is a power rectifier (slow switching, high current). • If you put a 1N4007 in a high-speed data circuit, it will be too slow and fail to work.• If you put a 1N4148 in a power circuit, it will likely burn out due to its lower current limit (200mA vs 1A).4. How much current can a 1N4007 diode handle?It can handle 1 Ampere of continuous rectified current. It can handle a non-repetitive surge of 30 Amperes (for less than 8.3ms), which is useful for inrush current at startup.5. What is the voltage drop of 1N4007?While often cited as 0.6V or 0.7V, under a full 1A load, the voltage drop is typically 0.9V to 1.1V.6. What is M7 diode?M7 is the surface-mount (SMD) code for the 1N4007 diode in an SMA package. It has the same electrical specs: 1A, 1000V. body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; } h2 { color: #2c3e50; border-bottom: 2px solid #3598db; padding-bottom: 10px; margin-top: 30px; } h3 { color: #34495e; margin-top: 20px; } table { width: 100%; border-collapse: collapse; margin: 20px 0; } table, th, td { border: 1px solid #ddd; } th, td { padding: 12px; text-align: left; } th { background-color: #f2f2f2; } img { max-width: 100%; height: auto; display: block; margin: 20px auto; } .note { background-color: #f9f9f9; border-left: 6px solid #2196F3; padding: 10px; font-style: italic; } .warning { background-color: #fff3cd; border-left: 6px solid #ffc107; padding: 10px; }

IntroductionRelays are fundamental components in modern electronics, serving as switches that open and close circuits both electronically and mechanically. They regulate the flow of electricity by controlling circuit contacts. Even in 2025, with the rise of solid-state technology, electromechanical relays remain vital for high-current applications.Understanding the state of a relay is crucial:Normally Open (NO): The circuit is disconnected when the relay is inactive (not energized).Normally Closed (NC): The circuit is connected when the relay is inactive.When energy (electricity or an electrical charge) is supplied to the coil, these states change, allowing for precise control over high-power systems using low-power signals.Ⅰ What is a Relay and How Does it Work?A relay is an electrically operated switch. Traditional relays employ an electromagnet (coil) to mechanically operate a switching mechanism (contacts). When the coil is activated, it generates a magnetic field that moves the armature, changing the state of the contacts from open to closed (or vice versa).The relay diagrams below demonstrate the operational logic of standard relays.1.1 Sample Wiring Diagrams for a Normally Open RelayExample 1: A four-pin (normally open) relay with the switch placed on the positive side of the control circuit.Figure 1: Positive side switching configuration.Example 2: A four-pin (normally open) relay with the switch placed on the negative side of the control circuit.Figure 2: Negative side switching configuration.Ⅱ Relay Related Video Introduction Topic: Relay Terminal Numbering System, IEC Schematic Symbols, and Coil Voltage Explained.Video Description: In this tutorial, we explore how the Terminal Numbering system works (identifying relay pins), the IEC schematic symbol for 8-pin Ice Cube relays and Mini contactor relays, and critical information regarding Coil voltage. Specifically, we address why you cannot use DC voltage on a coil designed strictly for AC voltage.Ⅲ Why use a Relay?Relays allow a low-current circuit (like a microcontroller or dashboard switch) to control a high-current circuit (like a motor or headlight array). As of 2025, this isolation is critical for protecting sensitive digital electronics. Key advantages include:Safety & Protection: High-amperage power is kept away from the operator interface and sensitive control units.Cost & Space Efficiency: Thinner gauge wires connect the control switch to the relay, saving weight, space, and copper costs.Voltage Drop Reduction: Relays allow power to be routed directly from the source to the device over the shortest distance, minimizing voltage loss.Heavy Duty Compatibility: Heavy gauge cable is only required for the short run from the power source to the device (via the relay).3.1 Why does a Car Need a Relay?Automotive applications rely heavily on relays. Using a relay eliminates the need for high-current rated switches on the dashboard, which are bulky and expensive. Secondly, relays allow for decentralized power distribution; they can be placed closer to the load (e.g., headlights, electric motors, cooling fans) to ensure maximum efficiency. In modern Electric Vehicles (EVs), high-voltage relays are essential for battery management and safety disconnects.3.2 Why are Protection Devices used in a Relay?When an electromagnetic relay turns off, the magnetic field in the coil collapses rapidly, generating a significant voltage spike (Back EMF). This spike can damage sensitive components in the control circuit (like the ECU or transistors). To prevent this, Flyback Diodes or resistors are often installed across the relay coil. While resistors are more durable, diodes are generally more effective at clamping the voltage spike. The choice depends on the sensitivity of the driving circuit.Ⅳ How to Understand the Electrical Specifications of a Relay?Reading a relay's datasheet is vital for system longevity. Specifications are generally divided into two parts:Coil Ratings: Specifies the voltage (e.g., 12VDC, 24VDC, 120VAC) required to energize the electromagnet.Contact Ratings: Specifies the maximum voltage and amperage the internal switch can handle. Never exceed this rating.For Double Throw relays, you may see specifications formatted as "2 x switch"—one rating for the Normally Open (N/O) terminal and another for the Normally Closed (N/C) terminal (e.g., N/O: 35A at 14VDC, N/C: 20A at 14VDC).Ⅴ What’s the difference between 4 or 5 Pin Relays?The primary difference lies in the switching capability. A 4-pin relay typically controls a single circuit (on/off), whereas a 5-pin relay can switch power between two different circuits.4 Pin Relay (SPST - Single Pole Single Throw)4-pin relays typically feature two control pins (85 and 86) for the coil, and two power pins (30 and 87). They act as a simple on/off switch. When the coil is energized, the internal switch connects pin 30 to pin 87, powering the device.Figure 3: 4-Pin Relay (Open State)Figure 4: 4-Pin Relay (Closed/Energized State)5 Pin Relay (SPDT - Single Pole Double Throw)5-pin relays include two control pins (85 and 86), a common power pin (30), a Normally Open pin (87), and a Normally Closed pin (87A). This allows the relay to toggle power between two circuits. When at rest, power flows to 87A; when energized, power switches to 87.Figure 5: 5-Pin Relay SchematicNote: These diagrams are simplified to demonstrate functionality. If the relay coil is protected by a diode (internal or external), the coil terminal wired to the diode's anode must be connected to the negative ground to ensure proper polarity and protection.Ⅵ All Types of Relay SymbolsRelays vary by function, construction, and terminal configuration. Below is a list of common relay types and their schematic symbols.Electromagnetic RelayThe standard relay using a coil and magnetic field to move contacts mechanically.Figure 6: Electromagnetic Relay SymbolThermal Overload RelayThis relay uses a bimetallic strip instead of a magnetic coil. The strip bends as it heats up from current flow, opening auxiliary contacts to protect motors from overheating.Figure 7: Thermal Overload Relay SymbolSPST RelaySingle Pole Single Throw: Has four terminals total. It connects one input to one output.Figure 8: SPST Relay SymbolSPDT RelaySingle Pole Double Throw: Has five terminals. It features one common terminal that switches between a Normally Open (NO) and a Normally Closed (NC) terminal.Figure 9: SPDT Relay SymbolDouble Coil Latching RelayLatching relays maintain their contact position after the power is removed. A double coil version uses one coil to set the position and another to reset it.Figure 10: Latching Relay SymbolOvercurrent RelayDesigned to operate only when the current exceeds a specific threshold, protecting circuits from faults.Figure 11: Overcurrent Relay SymbolDifferential RelayActivates when there is a difference between two identical electrical quantities (e.g., input current vs. output current), commonly used in transformer protection.Figure 12: Differential Relay SymbolPulse RelayOperates based on pulse signals, toggling the contact state with each input pulse. Essential for lighting control systems.Figure 13: Pulse Relay SymbolOn/Off Time Delay RelayContains a timing mechanism that delays the closing or opening of contacts after the coil is energized or de-energized.Figure 14: Time Delay Relay SymbolRemanence RelayA specific type of latching relay that uses the magnetic remanence (residual magnetism) of the core to hold the position without continuous power.Figure 15: Remanence Relay SymbolNo Volt RelayAlso known as an Under-voltage Relay. It trips the circuit breaker when the voltage drops below a safe operational level.Figure 16: No Volt Relay SymbolAC and DC RelayWhile they perform similar switching functions, AC and DC relay coils are constructed differently regarding internal resistance and impedance.Figure 17: AC and DC Relay SymbolsPolarized RelayContains a permanent magnet in addition to the coil. The state of the contacts depends on the polarity of the input signal.Figure 18: Polarized Relay SymbolDistance Relay (Impedance Relay)Used primarily in high-voltage transmission lines. It detects faults by measuring the impedance on the line, which corresponds to the physical distance to the fault location.Figure 19: Distance or Impedance Relay SymbolⅦ FAQ1. What is the main purpose of a relay in a circuit?A relay acts as an electrically operated switch. It allows a low-power signal (like from a microcontroller) to control a high-power circuit (like a heater or motor), while keeping the two circuits electrically isolated.2. What is the circuit symbol for an amplifier vs. an aerial?While not relays, these are common components in related schematics:Amplifier: Represented by a triangle on its side. It increases signal strength.Aerial (Antenna): Often abbreviated as 'AE', it is the device used to transmit or receive signals.3. How is a relay connected to a transistor circuit?In a standard driver circuit, the relay coil is often connected to the Collector of a transistor. However, in an Emitter Follower configuration, the coil can be connected to the Emitter, where the input signal drives the Base and the output is taken from the Emitter load.4. How does a 12V automotive relay work?The relay is installed between the battery (power source) and the accessory (load). When the dashboard switch is flipped, it sends a small current to the relay coil. The coil energizes, closing the internal high-current contacts, allowing power to flow directly from the battery to the accessory.5. Why are symbols used in circuit diagrams?Schematic symbols provide a standardized, universal language for engineers. They show how components are electrically connected (logic), rather than their physical layout. This allows for easier troubleshooting and design verification.

Introduction The laser displacement sensor is a device that uses laser technology for measuring. It consists of a laser, a laser detector and a measuring circuit. It is a new type of measuring instrument. For example, it can accurately measure the position and displacement of a object in a non-contact method.The laser has the excellent characteristics of good straightness, so the same laser displacement sensor has higher accuracy than the known ultrasonic sensor. However, the laser generating device is relatively complex and large in size. Therefore the application range of the laser displacement sensor is strict. Catalog Introduction Ⅰ Basic Working Principle 1.1 Measurement Objects 1.2 Measurement Methods Ⅱ Measurement Applications in Product Line Ⅲ Laser Displacement Sensors Advantages Ⅳ Alternative Types of Laser Displacement Sensor Ⅴ Laser Displacement Sensors Suppliers Ⅵ FAQ Ⅰ Basic Working Principle 1.1 Measurement Objects The laser beam emitted by the laser diode is irradiated to the surface of the object to be measured, and the reflected light passes through a set of lenses and is projected onto the photosensitive element matrix. The photosensitive part can be a CCD(charge-coupled device), CMOS(complimentary metal oxide semiconductor) or a PSD(position-sensitive detector) element. And the intensity of the reflected light depends on the surface characteristics of the measured object. The laser displacement sensor can also measure thickness, vibration, distance, diameter and other geometric quantities of the detected object. displacement sensor working state" width="294" height="222" /> Figure 1. Laser Displacement Sensor Working State 1.2 Measurement Methods According to the measurement principle, there are laser triangulation method and laser echo analysis method. The former method is generally suitable for high-precision and short-distance measurement, while the latter method is used for long-distance measurement. The following are the details of there methods.🔺Triangulation MethodThe simplest triangular displacement measurement system is to emit a beam of light from the light source to the surface of the object, and observe the position of the reflection point through imaging in the other direction, so that the displacement of the object can be detected. Since the incident and reflected light form a triangle, this method is called triangulation. According to the relationship between the angle between the incident light and the surface of the object to be measured, it can be divided into direct type and inclined type.The light emitted by the laser, after being focused by the condenser lens, is vertically incident on the surface of the measured object, and the movement of the object or the surface change causes the incident light spot to move along the incident optical axis. Receive the scattered light from the incident point of the lens and image it on the sensitive surface of the position detector (such as PSD, CDD) of the light spot. However, the laser beam of the sensor is perpendicular to the measured surface. So there is only one accurate focus position, and the images at the other positions are in different degrees of high focus state. In addition, high focus will cause the dispersion of the image point, thereby reducing the measuring accuracy. Figure 2. Light Path (direct-injection type) In order to improve accuracy, θ1 and θ2 must meet: tgθ1=Utgθ2In the formula, U is the lateral magnification. At this time, the side points within a certain depth of field can be imaged on the detector in focus to ensure accuracy.If the displacement of the light spot on the imaging surface is x', using the proportional relationship between the sides of similar triangles. The displacement of the measured surface can be obtained according to the following formula: In the formula, α is the distance from the intersection of the laser beam optical axis and the receiving optical axis to the front main surface of the receiving lens, and b is the distance from the rear main surface of the receiving lens to the center point of the imaging surface. θ1 is the angle between the optical axis of the laser beam and the optical axis of the receiving lens, and θ2 is the angle between the measured normal line and the optical axis of the receiving lens. Figure 3. Light Path (inclined type) The light emitted by the laser is incident on the measured surface at a certain angle with the normal direction of the measured surface, and the scattered light or reflected light of the measured surface of the light spot is also received by the receiving lens. The conditions should be satisfied at: tg(θ1+θ2)=Utgθ3If the image of the light spot moves x'on the sensitive surface of the detector, using the proportional relationship of similar triangles, the moving distance of the object surface along the normal direction is: Where, θ1 is the angle between the optical axis of the laser beam and the normal of the measured surface. θ2 is the angle between the optical axis of the imaging lens and the normal of the measured surface. θ3 is the angle between the optical axis of the detector and the optical axis of the imaging lens. The laser transmitter shoots the visible red laser light to the surface of the object to be measured through the lens. The laser light scattered by the surface of the object passes through the receiver lens and is received by the internal CCD linear camera. According to different distances, the camera can be set at different angles to trace this light spot. Based on this angle and the known distance between the laser and the camera, the digital signal processor can calculate the distance between the sensor and the measured object.And meanwhile, the position of the light beam at the receiving element is processed by analog and digital circuits, and the corresponding output value is calculated by the microprocessor analysis. Finally, the standard data signal is output proportionally in the analog window set by the user. If the switch output is used, it will be turned on within the set window and turned off outside the window. In addition, the analog quantity and the switch quantity output can set up the detection window independently.The maximum linearity of the laser displacement sensor adopting the triangulation method can reach 1um, and the resolution can reach the level of 0.1um. For example, the ZLDS100 type sensor can achieve high resolution of 0.01%, high linearity of 0.1%, high response of 9.4KHz, and can adapt to harsh environments. 🔺The Echo AnalysisThe laser displacement sensor uses the principle of echo analysis to measure the distance to achieve a certain degree of accuracy. The inside of the sensor is composed of a processor unit, an echo processing unit, a laser transmitter, and a laser receiver. The laser displacement sensor emits one million laser pulses per second through the laser transmitter to the detection object and returns to the receiver. The processor calculates the time required for the laser pulse to meet the detection object and return to the receiver to calculate the distance. The output value is the average output of thousands of measurement results. It is measured by the so-called pulse time method. The laser echo analysis method is suitable for long-distance detection, but the measurement accuracy is lower than that of the laser triangulation method, and the farthest detection distance can reach 250m. Figure 4. Laser Displacement Sensor Application Ⅱ Measurement Applications in Product Line Laser displacement sensors are often used to measure physical quantities such as length, distance, vibration, speed, and orientation, and can also be used for flaw detection and atmospheric pollutant monitoring.1) Size determinationPosition identification of small parts, monitoring of the presence of parts on the conveyor belt, detection of material overlap and coverage, control of the robot position (tool center position), device status, device position (through small holes), liquid level monitoring, thickness measurement, vibration analysis, crash test measurement, automobile related test, etc.2) Thickness Measurement of Metal Flakes and Thin PlatesThe laser sensor measures the thickness of a thin metal sheet (thin plate). Detection of changes in thickness can help find wrinkles, small holes or overlaps to avoid machine malfunctions.3) Simultaneous MeasurementGetting more values includes angle, length, inner and outer diameter eccentricity, conicity, concentricity and surface profile.4) Stuff Length MeasurementPut the measured stuff on the conveyor belt at the designated position, the laser sensor detects the it and measures it simultaneously with the triggered laser scanner, and finally obtains the length.5) Inspection of UniformityPlace several laser sensors in a row in the tilt direction of the workpiece to be measured, and directly output the measurement value through one sensor. In addition, you can also use a software to calculate the measurement value and read the result according to the signal or data.6) Inspection of Electronic ComponentsUse two laser scanners to place the component under test between them, and finally read the data through the sensor to detect the accuracy and completeness of the component size.7) Inspection of Filling Level on the Production LineThe laser sensor is integrated into the manufacturing of the filling product. When the product passes the sensor, it can be detected whether it is full. The sensor uses the extended program of the laser beam reflection surface to accurately identify whether the filling product is qualified and the quantity of the product.8) Measuring the Straightness of the ObjectFirst, 2-3 laser displacement sensors are needed to perform combined measurement. Then install them on a straight line parallel to the production line, and determine the distance between the three laser displacement sensors according to the measurement accuracy you need. Finally, you need to make this object move in a direction parallel to the installation line.When the production line and the sensor installation line are parallel, the greater the difference between the distances measured by the three sensors, the worse the straightness of the object, and the smaller the difference between the distances measured by the three sensors, indicating the straightness of the object. A straightness percentage can be established based on the length of the object and the distance between the three sensors, so as to obtain a quantified signal output, which has got the quantified signal output of detecting the object straightness. Figure 5. Light Receiver of Laser Displacement Sensor Ⅲ Laser Displacement Sensors Advantages 1) High Resolution and RepeatabilityEven in a larger working range, the sensor can still maintain a higher resolution and repeatability.2) Stable PerformanceThe sensor is less affected by the material and surface characteristics of the measured object, and it can directly measure the highly reflective, diffuse reflective and rough surfaces of different materials without spraying developer powder (Except for a few special materials).3) Measurement of Holes and Complex Geometric SurfacesThe coaxiality of the laser sensor enables high-precision measurement of deep holes, narrow slots, grooves and blind holes.4) Large Measurable AngleThe maximum measurable angle range of the laser sensor is 170° (±85°) in space. This technology enables the sensor to truly restore every minute detail of the complex surface of the measured object without causing any damage to the measured object.   Ⅳ Alternative Types of Laser Displacement Sensor 1) Eddy Current Displacement SensorResolution: The maximum resolution of the eddy current sensor can reach 0.1um, which is basically equivalent to the laser displacement sensor.Linearity: The linearity of the eddy current sensor is generally low, about 1% of the range, and the high-end laser displacement sensor is generally 0.1%.Measurement Conditions: The eddy current sensor requires the measured object to be a conductor and non-magnetic, that is, a non-magnetic conductor, such as aluminum, copper, etc., The laser displacement sensor is suitable for whether the measured object is magnetic or conductive. There are intersections between the two.2) Capacitive Displacement SensorThe accuracy of capacitive displacement sensors is very higher than laser displacement sensors, but the range of them is very small and generally less than 1mm, and the range of laser displacement sensors can be up to 2m.3) Fiber Optical Displacement SensorThe measurement principle of the fiber optical displacement sensor is measuring the change of the light flux and light intensity reflected on the surface of the object due to the displacement. And the probe is composed of two parts: a transmitting fiber and a receiving fiber. For the displacement and vibration of small objects, the conventional non-contact displacement sensor is limited by the reflection area and the measuring result is not ideal, while the optical fiber displacement sensor can be made into a very small probe (minimum 0.2mm diameter). What’s more, it can also be made into a form of linear transmission and reception. The displacement value can be calculated by measuring the degree of obstruction of the optical fiber during the displacement process. The accuracy can reach 0.01um, and the range can be up to 4mm. Figure 6. Fiber Optical Displacement Sensor Ⅴ Laser Displacement Sensors Suppliers Suppliers IFM Efector, Inc. MTI Instruments, Inc. Kinequip, Inc. LMI Technologies Inc. Mod-Tronic Instruments Limited Digi-Key Micro-Epsilon Diamond Technologies, Inc. Wenglor sensoric LLC Ergonomic Partners Automation Products Group, Inc. Schmitt Industries, Inc. Polytec, Inc. Baumer Ltd. Limab Rockwell Automation Baumann Machinery RIEGL USA, Inc. Linear Measurement Instruments Corp. Steven Engineering Zygo Corporation PICS INC Industrial Controls Finch Automation   Ⅵ FAQ 1. What is laser displacement sensor?The principle of laser displacement sensor ranging is a method where triangulation is applied by combining the emitting element and the position sensitive device (PSD) to perform ranging (detecting the amount of displacement). ... The laser light is focused through the emitting lens and projected on an object. 2. How does a displacement sensor work?A Displacement Sensor measures and detects changes (displacement) in a physical quantity. The Sensor can measure the height, width, and thickness of an object by determining the amount of displacement of that object. A Measurement Sensor measures the position and dimensions of an object. 3. Which sensor is used to measure the displacement?Inductive sensors – this technology uses alternating currents and is used to measure linear displacement. 4. Where are displacement sensors used?A displacement sensor (displacement gauge) is used to measure travel range between where an object is and a reference position. Displacement sensors can be used for dimension measurement to determine an object's height, thickness, and width in addition to travel range. 5. What are the types of displacement sensors?Displacement Sensor Types:Linear Displacement SensorsRotary Displacement SensorsEncodersCable Extension TransducersMembrane Potentiometers 6. Which laser sensor is used for measuring very long distances?LDM301 laser distance sensor series – fast measurement of long distances. The laser distance sensors of the LDM301 series use a measured time-of-flight principle to measure distances of 300 m for natural surfaces and 3,000 m for reflective surfaces. 7. What are the different laser sensors?The different types of laser sensors include charge-coupled devices (CCD), complimentary metal oxide semiconductors (CMOS), position-sensitive detectors (PSD), and photoelectric sensors. 8. How do laser position sensors work?The laser emits a laser beam to the target as shown above. The light reflected off the target is concentrated by the receiver lens and forms an image on the light receiving element. When the distance changes, the concentrated light reflects at a different angle and the position of the image changes accordingly. 9. How can sensors be used to detect objects?Ultrasonic sensors use sound waves to detect objects. Most ultrasonic sensors detect objects and measure distance by listening for the return echo of an emitted sound wave reflecting off of a target or background condition. 10. How do position sensors work?In Hall-effect position sensors, a moving part is linked to a magnet housed with a sensor shaft thereby forming a Hall element. With the movement of the body or its part the magnet also moves which leads to the formation of magnetic field and hence Hall voltage.

Ⅰ IntroductionThe potentiometer is a fundamental component that remains essential in 2025's electronics landscape.Widely used in circuits to control volume in audio equipment, adjust lighting brightness (dimmers), and calibrate sensors in IoT devices, potentiometers bridge the gap between user input and digital or analog response.While the working principle might seem complex at first, understanding the internal construction simplifies the concept. Whether you are working with classic analog circuits or interfacing with modern microcontrollers like Arduino or ESP32, mastering the potentiometer is a key skill. Figure 1: Standard Rotary PotentiometerⅡ Potentiometer Related Video Introduction Video: How A Potentiometer Works & Options for Wiring Potentiometer Video Description: This video explains the internal mechanics of a potentiometer and demonstrates common wiring configurations, including volume control (voltage divider), variable resistor, and signal blender setups. Ⅲ Potentiometer Basics3.1 Potentiometer SymbolTwo primary symbols represent potentiometers. The American standard (ANSI) depicts a zigzag line with three terminals, while the international standard (IEC) uses a rectangular box with three terminals. Both symbols indicate a fixed resistive track with a third terminal (the wiper) connecting to the center.  Figure 2: ANSI vs. IEC Potentiometer Symbols 3.2 Potentiometer Pin ConfigurationPin No.Pin NameDescription1Fixed EndConnected to one end of the resistive track (often Ground in volume circuits).2Variable End (Wiper)The wiper terminal that moves along the track to provide variable voltage or resistance.3Fixed EndConnected to the other end of the resistive track (often Input or VCC). 3.3 FeaturesTechnical specifications vary by model, but standard rotary potentiometers generally feature:Type: Rotary (Panel Mount or PCB Mount)Standard Resistance Values: 1K, 5K, 10K, 50K, 100K, 500K, 1M Ohm.Power Rating: Typically 0.25W to 0.5W for carbon film; higher for wirewound.Maximum Input Voltage: Often rated up to 200V DC (check datasheet).Rotational Life: Standard carbon pots offer ~10,000 to 15,000 cycles. High-end conductive plastic models can exceed 1-2 million cycles. 3.4 Selecting a PotentiometerPotentiometers (POTs) are essentially variable resistors. They adjust voltage or signal levels via a mechanical knob. Selection depends on two main criteria: Resistance (R-ohms) and Power (P-Watts).The resistance value determines the load placed on the source circuit. Common values include 10K and 100K for audio and signal processing. High-impedance circuits often require 500K or 1M pots.The power rating indicates how much heat the component can dissipate. Standard potentiometers are rated around 0.3W to 0.5W, making them suitable for low-current control signals, but not for directly driving high-power motors or heavy loads. 3.5 How to Use a Potentiometer?While standard resistors have two terminals, a potentiometer has three. The diagram below illustrates the internal function. Figure 3: Internal Structure of a Potentiometer The resistive track between terminals 1 and 3 provides a constant resistance (e.g., 10kΩ). The wiper (terminal 2) moves along this track, tapping into the voltage at a specific point.For example, with a 10k linear potentiometer:Resistance between Pin 1 and Pin 3 is always 10kΩ.If the wiper is set to the exact center (50%), the resistance between Pin 1 and Pin 2 is 5kΩ, and Pin 2 to Pin 3 is also 5kΩ.This "Voltage Divider" principle is what makes potentiometers effective for reading analog signals into microcontrollers like an Arduino. 3.6 ApplicationsAudio Control: Volume and tone knobs in guitars and amplifiers.Position Sensing: Joysticks in gaming controllers and servo motors in robotics.User Interface: Control dials for dimmers, fan speeds, and temperature settings.Calibration: Trimmer potentiometers (trimpots) are used on PCBs to fine-tune circuit performance. 3.7 2D Diagram (Model P232)Figure 4: Mechanical Dimensions (Model P232)  Ⅳ How to Wire a Potentiometer?Wiring a potentiometer is straightforward, but correctness depends on the application (Volume vs. Variable Resistor). The most common configuration is the Voltage Divider (Volume Control), where you ground the first terminal, input signal to the third, and take the output from the middle wiper. 4.1 Part 1: Selecting and Preparing a Pot Step 1: Identify Terminals. Place the pot on a flat surface with the shaft pointing up and terminals facing you. Terminal 1 (Left): Typically Ground. Terminal 2 (Middle): Output (Wiper). Terminal 3 (Right): Input (VCC/Signal). Step 2: Check Specifications. Locate the markings on the case. "100K" indicates a maximum resistance of 100,000 ohms. Verify the taper code (e.g., 'B' often usually Linear, 'A' usually Audio/Logarithmic in modern Asian/American components).Tip: Choose resistance based on your circuit. A 10K pot is standard for microcontroller inputs (5V logic), while audio circuits often use 100K or 250K/500K for guitars. Step 3: Preparation. Ensure your electronic device is unplugged to prevent short circuits. If prototyping, insert the pot into a breadboard. If soldering to a panel, ensure the surface is clean.Step 4: Wire Prep. Measure and cut your wires. Strip approximately 0.5 inches (1.3 cm) of insulation from the ends. Use standard rosin-core solder for electronics; avoid acid-core solder (used for plumbing) as it damages circuit boards. 4.2 Part 2: Soldering Your TerminalsStep 5: Ground Connection. Solder a wire from Terminal 1 (Left) to the Ground (GND) point on your device or chassis. This sets the "zero" point for the volume/voltage. Step 6: Signal Output (Wiper). Connect a wire to Terminal 2 (Middle). This is your modified signal. If connecting to a microcontroller (like Arduino), this wire goes to an Analog Input (e.g., A0). If using it for audio, this goes to the amplifier input. Step 7: Signal Input. Connect Terminal 3 (Right) to your signal source or voltage supply (e.g., 5V or Audio Source). This allows the current to flow across the resistive track to the ground. 4.3 Part 3: Using Your PotentiometerStep 8: Testing. Before powering up, you can use a multimeter set to Resistance (Ohms). Measure across Pins 1 and 2. Turning the knob should smoothly change the resistance value. Step 9: Operation. Power on your device. Turning the knob clockwise should increase the signal (volume/voltage), and counter-clockwise should decrease it.Finishing Touches: You can add a knob cap for better ergonomics and aesthetics. Ensure the pot is securely mounted to prevent the wires from twisting during operation. Ⅴ FAQ1. What are the main types of potentiometers?Potentiometers are classified by their construction and movement:Rotary Potentiometers: The most common type, controlled by turning a knob.Linear (Slide) Potentiometers: Controlled by sliding a fader, common in audio mixers.Digital Potentiometers (DigiPots): Controlled electronically via protocols like I2C or SPI, used in modern digital circuits.Membrane Potentiometers: Flat, flexible sensors used in touch interfaces. 2. How do you read potentiometer taper markings (A vs. B)?The "Taper" indicates how resistance changes as you turn the knob. Modern Standard (Asia/USA/IEC): A = Audio (Logarithmic) Taper: Resistance changes slowly at first, then quickly. Best for volume controls because human hearing is logarithmic. B = Linear Taper: Resistance changes evenly. Best for adjusting brightness, fan speed, or sensor calibration.Note: Vintage European devices sometimes used the reverse (A=Linear, B=Log), but modern components almost universally follow A=Log, B=Linear. 3. What does "10k potentiometer" mean?This designation refers to the total resistance of the component. If you measure the resistance between the two outer terminals (Pin 1 and Pin 3), it will always read 10kΩ (10,000 ohms), regardless of the knob's position. The wiper allows you to select a value between 0Ω and 10kΩ. 4. When should I use a low vs. high resistance potentiometer?Low Resistance (e.g., 1k - 10k): Best for signals driving standard inputs (like Arduino pins) or to minimize noise interference. High Resistance (e.g., 250k - 1M): Best for high-impedance sources, such as electric guitar pickups, to prevent signal loss (loading) which preserves treble frequencies. 

Ⅰ Introduction A flyback converter has the function of a simple switch-mode power supply, which is usually applied in either AC or DC applications. This low- to mid-power device with multiple outputs transfers power from the input to the output during off-time. It can be found in a television set, a plasma lamp, and a variety of other electronic devices that require high voltage.   flyback transformers which I have met with." width="455" height="240" />  6 different kinds of flyback transformers which I have met with   Catalog Ⅰ Introduction Ⅱ Basics of Flyback Transformers 2.1 What are Flyback Transformers? 2.2 What is a flyback? Ⅲ How Does a Flyback Transformer Work? Ⅳ Design of Flyback Transformer 4.1 Key Components of Flyback Transformer 4.2 Design of Flyback Transformer Ⅴ Advantage  and application of Flyback Transformers 5.1 Advantages of Using Flyback Transformers 5.2 What are typical flyback transformer applications? Ⅵ Practical Projects of Flyback Transformers Ⅶ FAQ       Ⅱ Basics of Flyback Transformers   2.1 What are Flyback Transformers?   A flyback transformer is a gapped-core coupled inductor. When the input voltage is applied to the primary winding during each cycle, energy is stored in the gap of the core. It is then transferred to the secondary winding, where it is used to power the load. Flyback transformers are used in flyback converters to provide voltage transformation and circuit isolation.   Flyback transformers are the most common choice for low-cost, high-efficiency isolated power supply designs up to 120 Watts. They offer circuit isolation, the ability to have multiple outputs, and the ability to have positive or negative output voltages. They can also be controlled across a wide range of input voltage and load conditions. Because the energy is stored in the transformer, the flyback topology, unlike the other isolated topologies, does not require a separate output filter inductor. This reduces the number of components required and simplifies the circuit requirements. This article goes over flyback transformers and the applications that they are best suited for. What is a flybackTransformers ?     2.2 What is a flyback?   In the condition of flyback topologies, energy is kept in the magnetic field of the transformer during the first half of the switching cycle, but in the second half of the cycle, it is released to the secondary winding(s) connected to the load. Flyback transformers have a gapped-core design that allows for high energy storage without oversaturating the core. This aspect of energy storage distinguishes flybacks from other topologies such as forward-mode, in which energy is transferred directly from primary to secondary. Flyback transformers are also known as coupled inductors as the gapped core and stored energy.   The circuit of a flyback transformer？       Ⅲ How Does a Flyback Transformer Work?   A flyback transformer circuit resembles other isolated transformer circuits in appearance and has many of the same components, such as a switch, output rectifier or diode, and input and output capacitors. However, compared with other isolated transformers, flyback transformers store energy within the core and do not require a separate output inductor. By ensuring circuit isolation and allowing both positive and negative output voltage, this highly efficient construction facilitates cost-effective power usage.   Switch The metal oxide semiconductor field-effect transistor (MOSFET) is the most common switch design for flyback converters, consisting of three terminals that modify the intensity of and redirect electronic signals. Flyback converter switches can also consist of bipolar transistors, gallium nitride (GaN), or silicon carbide (SiC). Current flows are stored in the core through the primary coil when the switch is closed (or in the on position). When the switch is turned off, current flows through the secondary coil and is transmitted to the output load. The output voltage is adjusted by varying the duty cycles and turn ratios of the primary and secondary coils.   Coupled Inductor A coupled inductor is made up of the coils that transmit and store energy in a flyback transformer. Mutual electromagnetic inductance connects the two coils—when energy flows into the primary coil, it creates a magnetic link and generates a voltage in the second coil. The function of coupled inductors is to change the voltage. They can also be used to isolate circuit components to improve electrical flow efficiency. When the switch is turned on, energy enters the primary winding and is stored in the core. When the switch is in off status, the stored magnetic flux flows into the secondary winding, and the energy is distributed via a diode.   Output Diode As current flows from the second coil, it can be increased, decreased, or modified. Diodes ensure that current flows unidirectionally toward the output and that the voltage remains constant to meet the application's requirements. Because the current from the transformer can fluctuate depending on the input voltage, the diode, and output capacitor help to maintain a constant outflow of current.   Input and Output Capacitors In flyback transformers, capacitors can be installed on both the input and output ends of the current flow. They are used to reserve energy to release it in controlled amounts. Input capacitors manage the flow of energy into the primary coil, while output capacitors manage the flow of energy to ensure a smooth flow at the desired voltage and current.     Fig. 2: Current when switching on and off       Ⅳ Design of Flyback Transformer   4.1 Key Components of Flyback Transformer Primary switchMutually coupled inductorOutput rectifierInput capacitorOutput capacitor     4.2 Design of Flyback Transformer It is made up of a few electrical components. A switching device, consisting of transistors or MOSFETs, is present at the input to turn on and off the primary coil's input voltage. In reverse bias, the secondary coil contains a diode that restricts current flow.       Fig 1. Construction of Flyback transformer   A flyback transformer, unlike other types of transformers, is designed to be excited by direct current voltage. A switch powered by a DC supply drives the primary winding. The magnetic flux is transferred to the secondary coil when the primary coil is activated. Because the secondary coil is connected to a diode in reverse bias., the current is stored. However, As a result, the next incoming primary winding pulse adds to the stored current (i.e the energy stored in the previous pulse). The result of this subsequent addition is a very high pulse of electricity at the output.       Ⅴ Advantage  and application of Flyback Transformers   5.1 Advantages of Using Flyback Transformers Flyback transformers have several advantages over other types of converters, including:   Circuit isolation. The circuit isolation provided by flyback transformers prevents electrical hazards and improves safety, especially for those working near high-energy electrical systems.   Compact size. Flyback transformers are smaller, lighter, and easier to install than comparable transformers due to their simple design, making them a better fit within your overall electrical system.   Cost-effectiveness. Flyback transformers typically cost the same as other transformers. However, because they contain fewer components, flyback converters – of which flyback transformers are an important component – are typically less expensive than comparable converters. This is important to remember when thinking about flyback transformers and their use in flyback converters.   Convenience Flyback transformers can be used to isolate and manipulate multiple output voltages from a single control.     5.2 What are typical flyback transformer applications? Flyback transformers can be used in a variety of applications, including:   DC-DC power suppliesTelecomLED LightingPower over Ethernet (PoE)Capacitor chargingBattery chargingSolar MicroinvertersAC-DC power supplies Flyback transformers are commonly used when the output current is less than 10 amps and the output power is less than 100 watts. Coilcraft sells standard, off-the-shelf flyback transformers ranging in power from a few Watts to around 120 Watts. Forward-mode, push-pull, and half-bridge / full-bridge topologies are more efficient when higher current and power are required.     Ⅵ Practical Projects of Flyback Transformers The drivers used to drive flyback transformers in flyback mode, or push-pull topology, are featured in this project because they are not conventional transformers.   Projects circuit   These flyback transformers can be found in anything with a CRT, such as TVs or monitors, and are responsible for generating high voltage to create an electric field. In turn, electrons are accelerated toward the screen, where they excite phosphors and form images. Flyback transformers are made of coupled inductors that are driven differently than iron-cored main transformers because they use a ferrite core that requires different operating conditions.   building drivers for flyback transformer   To avoid finding the built-in primary, you may need to consider winding your primary during construction. The primary turns can be adjusted to achieve the desired output voltage or drive voltage. The 555 astable modes is used in one flyback driver design.   Ⅶ FAQ 1. What is the function of flyback transformer? A flyback transformers, also known as a line output transformer, stores energy from input voltage in switched-mode power supplies. It is useful for multiple electrical applications. At one time, these transformers were used to meet high voltage needs at high frequencies.   2. Why is it called a flyback transformer? The reason it is called a flyback transformer is because the primary winding uses a relatively low-voltage saw-tooth wave. The wave gets strengthened first and then gets switched off abruptly; this causes the beam to fly back from right to left on the display.   3. What is a flyback transformer in CRT? A flyback transformer, sometimes called a line output transformer, is used in older CRT TV's and computer monitors to produce the high voltage required to drive the CRT and electron gun. They also have auxiliary low voltage windings which the TV designers use to power other parts of the TV.   4. What type of transformer do I have? In order to do this, simply look for the “W” on your device's label. This will help you determine which transformer you need. If the device is 300 watts, then you will need to buy a transformer that is also 300 watts.   5. Why flyback converter is used? Flyback converters are often used in power supplies requiring low to medium output power at several output voltages. With a flyback, multiple outputs incur little additional cost or complexity—each additional output requires only another transformer winding, rectifier and output filter capacitor.   6. How do I select a core for a flyback transformer? The ideal core material should have a maximum available ΔB and low core losses (proportional to the shaded area). Powder cores are made of tiny insulated particles, hence, the air gaps are distributed evenly through the core structure.        

Introduction In general, the radio is constructed by mechanical devices, electronic devices, magnets, etc. It receives the audio signals emitted by broadcasting stations through converting electric wave signals. After the invention of the vacuum tube, the circuit and receiving performance of the radio had undergone revolutionary progress and improvement, that is valve radio. Later, with the development of technology, radios with transistors as the core gradually became popular. It's what we know as a transistor radio. Radios are still widely used for many functions. Here two main radios will be described in detail below. Catalog Introduction Ⅰ Valve Tube Radio 1.1 Vacuum Tube Radio Classifications 1.2 Advantages and Disadvantages of Valve Radio 1.3 German Vintage Valve Radio Models for Sale Ⅱ Transistor Radio 2.1 Transistor Radio Overview 2.2 Transistor Radio Selection Matters 2.3 Transistor Radio Brands for Sale Ⅲ Radio Further Development Ⅳ FAQ Ⅰ Valve Tube Radio The valve radio, also known as the vacuum tube radio, was a product of the early 20th century, and immediately became the new favorite of that era with the launch of the broadcasting station. By the late 1920s, vacuum tube radio equipment replaced the primitive spark-gap systems on most merchant ships. This new equipment could send and receive signals virtually worldwide, by using high frequency or "short-wave" bands. Tube technology allowed radio signals to be tuned with much greater precision than spark-gap. The basic design for tube radio was perfected by the 1930s and continued in use on merchant vessels into the 1980s. 1.1 Vacuum Tube Radio Classifications 🔺AM (Amplitude Modulation) RadioIn the era when tube radios were popular, AM radios were the mainstream products. Amplitude modulation wave modulates the high-frequency carrier with audio signal. Its waveform is symmetrical, the amplitude is the same as that of the modulated signal, and then obtain the audio signal after high-frequency component is filtered out. In addition, the frequency of the carrier signal (the frequency of the broadcasting station) is the carrier frequency.AM radios can receive medium-wave and short-wave broadcasts, and some can receive long-wave broadcasts. Since the mid-band frequency interval has been unified to 9KHz, its highest audio frequency is only 4KHz. So the sound quality is affected because of large electromagnetic interference.There are two main types of AM radios: direct-amplifier type and external (self) differential type1) Direct-amp radio, also called high-amp radio, its typical circuit structure is as follows:High Amplifier—Detection—Low Amplifier—Power AmplifierA circuit that uses a grid detector circuit and high-frequency positive feedback is called a regenerative radio, which can obtain higher sensitivity and amplitude selectivity. A regenerative radio with high amplifier and short wave can receive AM telegraph signals. Most of the old Japanese-made radios have such circuits. Direct-amp radios are prone to self-excitation of high-frequency signals, high-end and low-end gains are uneven, and regenerative radios without high-amplification have poor selectivity. In addition, the reed speakers with poor sound quality are generally used, so they are gradually replaced by superheterodyne radios.Simple regenerative radios mostly use reed speakers, which have high impedance (about 10K) and high sensitivity. It can be directly used as the load of the power amplifier tube, but the frequency range is only 350~3000Hz, so the sound quality is poor. Later regenerative radios applied moving coil speakers, and the sound quality was better. However, because of low impedance, an output transformer is required, and its primary impedance must match the load impedance of the power amplifier tube. Moving coil speakers are divided into permanent magnets, constant magnets and excitation. Among them, excitation horns are used in AC electronic tube radios, and their excitation coils can also be used as filter chokes. 2) Heterodyne RadioThe heterodyne radio adopts a frequency conversion circuit. The signal generated by its high-frequency oscillation circuit and the input signal have a certain frequency difference. After the two are mixed, a fixed intermediate frequency signal (455~465KHz) is generated. Some people call the oscillation frequency higher than the signal frequency a heterodyne type, and vice versa.Heterodyne plus intermediate frequency amplifier circuit is called superheterodyne. This type of circuit requires a single electron tube to oscillate, and later a multi-pole or composite tube dedicated to frequency conversion appears. The superheterodyne type is the most common circuit of commercial radios. It has an automatic volume control circuit and can add tuning instructions. The circuit principle will be described in detail later. The superheterodyne radio can obtain more stable and higher gain due to amplifying the fixed frequency. The disadvantage is that there is image frequency interference.The circuit structure of a typical superheterodyne radio is as follows:Frequency Conversion—Middle Amplification—Detection—Low Amplification—Power Amplification 3) Autodyne Frequency Conversion RadioUsing ordinary pentodes for frequency conversion is only suitable for the mid-band, and the middle frequency is 175KHz. Due to the popularization of special frequency conversion tubes, it is rarely used now. Figure 1. Vintage AM Radio 🔺FM (Frequency Modulation) RadioFM radio is a radio that transmits radio signals through the use of FM frequency modulation carrier. Due to the shorter wavelength, the signal transmitted is much better than that of the radio that uses the AM wavelength. However, due to the short wave, the transmission distance is relatively short.FM wave is to use audio signal to modulate the frequency of high frequency carrier. Its advantages include strong anti-interference ability, high signal-to-noise ratio, good frequency bandwidth and sound quality, in addition, the audio frequency can reach 20Hz~15000Hz. Because the FM wave works in the ultra-high frequency band, it can accommodate many radio stations. With its linear propagation characteristics, the same frequency can be reused at a distance of hundreds of kilometers, which can effectively solve the problem of congestion of medium and short wave radio stations.Modern FM broadcasting is compatible with stereo and mono channels(in the early days of stereo broadcasting, two frequencies were used and two radios for reception). Some hobbyists are likely to use a simple super-regenerative circuit to receive FM broadcasts. Because it works in a self-oscillation state, the work is unstable and has strong super-noise. 1.2 Advantages and Disadvantages of Valve Radio Advantages of Valve Radio 1) The valve tube circuit has a simple structure and good anti-overload performance.2) The characteristics of the power amplifier circuit of the tube radio are better than those of the transistor or integrated circuit power amplifier. The screen current of the Class A power amplifier circuit with an output transformer for output impedance matching has little change at zero signal and full signal. So the performance is stable, the distortion of the line work area is very small, and the harmonic content is very rich .3) The speakers used in valve radios are generally larger in diameter than those of transistor or integrated circuit radios.4) The IF circuit characteristics of tube radios are better than those of transistor or integrated circuit radios.5) Have collection value. Disadvantages of Valve Radio As for the shortcomings, valve tubes that are large in size and used as basic components, built-in accessories are also bulky, power consumption has also increased, the overall quality has become poor, inconvenient to carry, and poor seismic performance. In addition, it is very difficult to make FM stereo radio devices, because early tube radios can only receive shortwave and medium waves. These shortcomings eventually led to the replacement of tube radios by transistor radios. Vintage Valve Radios - Will they work? 1.3 German Vintage Valve Radio Models for Sale AEG RadioBlaupunktGerman EMUDGraetz Vintage RadioGrundig Vintage RadioHornyphon Vintage RadioVintage Koerting RadioGerman Metz Vintage RadioVintage Nordmende RadioPhilips Vintage RadioVintage Saba RadioVintage Siemens RadioTelefunken Radio Figure 2. Vintage Valve Radio Ⅱ Transistor Radio 2.1 Transistor Radio Overview The transistor radio is the second generation radio after the valve radio. Compared with vacuum tubes, transistors are small in size, light in weight, resistant to vibration, long in life, and low in power consumption. This kind of radios can be made compact and have relatively stable performance. Therefore, after the advent of transistor radios, a large number of portable radios and pocket radios have emerged. They are very convenient for daily use. The Regency TR-1 was the first commercially manufactured transistor radio by developed by Texas Instruments and IDEA Inc., introduced in 1954.Transistor radios use transistors to process and amplify signals. Simple to use, it is a small transistor-based radio receiver. 2.2 Transistor Radio Selection Matters To choose a good transistor radio, you must first understand four basic relationships:1) The larger the chassis volume, the better the sound quality.2) The larger the horn diameter, the better the sound quality.3) The larger the battery volume, the longer the relative service life of the battery.4) The longer the magnetic bar, the higher the sensitivity.Secondly, we should also pay attention to five points when selecting:1) The change after the power supply voltage is reduced should be small. When selecting, you can have listening trial, because the impact on a high-quality radio should not be significant.2) The distortion of the offset radio should be small. After finding a radio station, having the left and right adjustments, the distortion should be small. In addition, there should be no whistling sound, otherwise, the frequency characteristics of the intermediate frequency part are poor.3) The volume change should be small when turning the button.4) Human body induction has little influence. When a person's body is close to the radio, it will have a certain impact on the work of the radio. This situation is particularly obvious for shortwave.5) The noise should be small. Noise generally includes electrical noise and mechanical noise. Turn the radio to a place where there is no station, and turn on the volume to the maximum. At this time, the minimum sound is better. Listen to a program to check whether there are noises caused by resonance of certain components when the volume is loud. Finally, you should also pay attention to whether the tuning knobs and buttons are coordinated and effective, and whether the shell of the radio is damaged or not. Vintage Transistor Radios Show And Tell 2.3 Transistor Radio Brands for Sale EdifierGAORUI HOME TEXTILESONYRoltonHALFSUNPandaSoaiyNintaus Figure 3. Regency tr-1 Transistor Radio Ⅲ Radio Further Development With the advent and development of integrated circuits, transistors have been replaced by integrated circuits, that is the third-generation radios invention, sometimes also known as semiconductor radios.After the radio uses integrated circuits, not only the size can be made smaller, but also the reliability is high. As the number of integrated circuit components is getting larger and larger, radios made with it have better performance and more functions. The integration of radios has become an inevitable trend.   Ⅳ FAQ 1. What is a vacuum tube radio?A vacuum tube, also called a valve in British English, is an electronic device used in many older model radios, television sets, and amplifiers to control electric current flow. The cathode is heated, as in a light bulb, so it will emit electrons. ... The anode is the part that accepts the emitted electrons. 2. Do valve radios still work?A valve radio will never be as reliable as a transistor set, and short of ripping out the chassis and replacing it with a transistor circuit, we aren't going to make it that reliable. However, some designs of valve set are more unreliable than others, and the main factor seems to be heat. 3. What did valves do in radios?The valve was useful as an electronic switch and its first use was in radio circuits detecting signals. The valve has two elements - a wire and a metal plate surrounded by a vacuum. The electricity flows between them. 4. How does a tube radio work?The basic working principle of a vacuum tube is a phenomenon called thermionic emission. It works like this: you heat up a metal, and the thermal energy knocks some electrons loose. 5. When did radios stop using vacuum tubes?1950s-60s - Most vacuum tubes were replaced by transistors in the west. 1970s-80s Tubes are still used in many specialized applications like broadcast television and radio. 6. Why did we stop using vacuum tubes?Vacuum tubes suffered a slow death during the 1950s and '60s thanks to the invention of the transistor—specifically, the ability to mass-produce transistors by chemically engraving, or etching, pieces of silicon. Transistors were smaller, cheaper, and longer lasting.A transistor is a semiconductor device used in electronic circuits as to function as "on" and "off" switching and amplifying device in the electronic circuits. ... Radio is a device which transmit and amplifies signals. The modern radio uses transistor since it is smaller in size. 7. Are transistor radios still being made?Transistor radio is an obsolete term now, carried over from when having transistors rather than tubes made small radios possible. It has come to be analogous to a portable, battery-powered radio, so while I will be making some recommendations, they likely will have integrated circuits, rather than transistors.It is a radio receiver which uses transistors to amplify the sound. Transistor radios can be cheap and small and some use very little electric power. Some can amplify the weak radio waves that are usually not picked up by weaker vacuum tube radios. 8. What does a transistor radio do?The function of transistors in radios is straightforward. Sounds are recorded through a microphone and turned into electrical signals. Those signals travel through a circuit, and the transistor amplifies the signal, which is subsequently much louder when it reaches a speaker. 9. Why was the transistor radio invented?One goal was to find a replacement for fragile and energy-wasting vacuum tubes. Building on war-time research, John Bardeen and Walter Brattain, working with group leader William Shockley, developed a device they called a transistor. 10. Where was the transistor radio invented?There was a tremendous push during the war to reduce the size and power consumption of vacuum tubes, particularly because the receivers used in radio-controlled bombs depended on vacuum tube technology. “Not long after the war ended, the transistor was developed at Bell Labs, in 1947. 11. What is the name of first transistor radio?Regency TR-1In July 1954 the Texas Instruments and Industrial Development Engineering Associates (I.D.E.A.) companies embarked on a six month project to produce a pocket-sized radio for the Christmas market. The result was the Regency TR-1, the world's first pocket transistor radio.