Phone

    00852-6915 1330

diagram Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

Resistors

How Relays Work? Relay Functions and Applications

IntroductionA relay is an electromagnetic switch operated by a relatively small electric current that can turn on or off a much larger electric current. It consists of a set of input terminals for a single or multiple control signals, and a set of operating contact terminals. Because of unique characteristics, it is widely used in many fields. How does a relay work? What the functions of relays, let’s check the following details.How Does A Relay Work?CatalogIntroductionⅠ Working Principle  1.1 Operation Example: Relay as a Switch  1.2 Working Principle of Different RelaysⅡ What is the Function of a Relay?  2.1 Summary  2.2 Types of RelayⅢ Relay Applications  3.1 Automotive Field  3.2 Household Appliance  3.3 Industrial Relays  3.4 Example Analysis: JYB-714 Liquid Level RelayⅣ Relay Selection RulesⅤ One Question Related to DC RelayⅥ Frequently Asked Questions about How Relay WorksⅠ Working PrincipleThe relay is generally composed of an iron core, coil, armature, contact reed and so on. As long as both ends of the coil having a voltage, a certain current will flow through the coil, which will produce electromagnetic effects. Under the action of the electromagnetic force, the armature will overcome the pull force of the return spring and attract to the core, thereby the movable contact and the static contact (normally opened terminal) are in the state of pull-in.Figure 1. Relay StructureWhen the coil is power-off, the electromagnetic attraction will disappear. The armature will move back to its original position under the reaction force of the spring, making the movable contact and the static contact (normally closed terminal) contract together. Under the actions of pull-in and release, achieve the purpose of conducting and cutting off in the circuit. 1.1 Operation Example: Relay as a SwitchThe following figure is the circuit diagram of the relay controlling the light. The relay has normally open contacts and normally closed contacts. The movable contact is a common terminal. This is a DC relay powered by a battery. When the coil of the relay is powered by a DC power supply, the coil with the iron core will generate the corresponding magnetic field to adsorb the armature, and the movable contact will move from the normally closed contact side to the normally open contact side, which is equal to the normally open contact being pulled in. We can see that the start/stop button, battery, and relay coil form a control loop. As long as this loop is closed, the current will flow through the coil and a magnetic field will be generated. The normally open contact, the lamp, and the control power supply (the other battery in the picture) form a loop. When the normally opened contact is closed, the loop is closed and the current will flow from the positive of control power supply to the bulb, passing through the closed normally opened contact to the negative pole, so that the light will on.Figure 2. A relay as a SwitchWhen the start/stop button disconnects, the coil has no current. So that the armature will not be attracted by the magnetic force, and will be reset by the spring. So that the other end of the moving contact will go from the normally opened contact to the normally closed contact. The circuit of the bulb is forcibly disconnected and does not turn on.Figure 3. Relay Controls a Light1.2 Working Principle of Different Relays1) Electromagnetic RelayIt works by using the suction force generated by the circuit in the input circuit between the electromagnet core and the armature.2) Solid State RelayElectronic components have their functions without mechanical moving parts, and the input and output are isolated.3) Temperature RelayIt will act when the outside temperature reaches a given value.4) Reed RelayUsing the reed action sealed in the tube, open, close, or switch the circuit with the function of the electric contact reed and the armature magnetic circuit.5) Time RelayWhen the input signal is added or removed, the output part needs to be delayed or time-limited before closing or opening its controlled circuit until the specified time.6) High-frequency Relay It is used to switch high-frequency and radiofrequency lines with minimal loss.7) Polarized RelayA polarized magnetic field and a control current are combined to act by the magnetic field generated by the control coil. Ⅱ What is the Function of a Relay?2.1 SummaryRelay is an automatic switching element with isolation function, which is widely used for remote control, telemetry, communication, automatic control, electronic equipment, etc. It is the most important control element in the circuits.Relays generally have a sensing mechanism (input part) that can reflect certain input variables (such as current, voltage, power, impedance, frequency, temperature, pressure, speed, light, etc.); there is a mechanism (input part) that can realize "switch on" and "switch off" to the controlled circuit. Between the input end and the output end of the relay, there is also an intermediate mechanism for coupling isolation of the input quantity, functional processing and driving the output part (driving part). As a control element, relays have the following functions:1) Expanding control rangeFor example, when the control signal of a multi-contact relay reaches a certain value, multiple circuits can be switched, disconnected, and connected at the same time from different forms of contact groups.2) AmplificationFor example, using a very small control quantity can control a large power circuit, such as sensitive relays, intermediate relays and so on.3) Integrated signalFor example, when multiple control signals are input to a multi-winding relay in a prescribed form, they will be relatively integrated to achieve a predetermined control effect.4) Automatic control, remote control, and monitoringFor example, the relay on the automatic device and other electrical appliances can form a program control circuit to realize automatic operation. 2.2 Types of RelayIntermediate RelayIt is the function of converting and transmitting the control signal. That is, its input signal is the power off/on the signal of the coil, and the output signal is the contact action of the intermediate relay. In essence, it belongs to one of the voltage relays and has the characteristics of multi-contacts (six pairs or even more). The contact can withstand a large current (rated current is 5A~10A), and its action is more sensitive (response time less than 0.05s). Voltage RelayIts main principle uses the voltage signal, and determines the action of the contact according to the coil voltage, in addition, the coil needs to be connected in parallel with the load during circuit design. The voltage relay can be divided into AC and DC type according to the coil voltage, and can be divided into overvoltage and Undervoltage according to the operating voltage. Therefore, their functions are also different. As for the overvoltage relay, when the coil voltage is within the rated value range, the armature will not make any pull-in action. On the contrary, the action will execute if the coil voltage is exceeded. The AC overvoltage relay plays the role of overvoltage protection in the circuit. When the coil voltage reaches or exceeds the rated value of the coil, the armature will make a pull-in action, and the coil voltage will be lower than the rated value. The Undervoltage relay mainly plays a role of Undervoltage protection in the circuit when the armature is released immediately. Current RelayIt works according to the current signal and determines the contact action according to the current of the coil. The current relay coil needs to be connected in series with the load when having the installation. According to the coil current, it can be divided into two types AC and DC. According to the action current, it can be divided into overcurrent and undercurrent types.Since the load current will pass through the coil when having overcurrent, the coil rated current (that is, the setting current) is usually chosen to be equal to the maximum load current. When the load current is not higher than the setting value, the armature will not act. On the contrary, if it exceeds, a pull-in action will occur. The main function of the overcurrent relay is to play overcurrent protection in the circuit, especially in some occasions where impulsive over-current occurs. Because it has a good protective effect.  The principle of the undercurrent relay is that when the current in the coil reaches or exceeds the operating current value, the armature will perform a pull-in action. On the contrary, the armature will be released immediately when the coil current is less than the operating current value. In a normal state, if the load current exceeds the working current of the coil, the armature will also perform pull-in. When the load current drops below the coil current, the armature will be released. Time RelayIt belongs to a relay that starts with the input signal (that is when the coil is powered on or off) and will output the signal (contact closed or disconnected) after a preset delay in advance. Time relays are generally used in relatively low voltage or current circuits to turn on and off higher voltage or current, just as an electric switch device in the circuit used for automatic control.Figure 4. Electrical Relay Symbol (SPST/SPDT/DPST/DPDT)Ⅲ Relay ApplicationsRelays are employed in a wide range of fields, and their environmental conditions and technical requirements vary greatly. What’s more, in the same application field there are different requirements. Here are some examples and a brief description.3.1 Automotive FieldThe automotive industry is increasingly using relays. The more common relays are: starting relays to start motors, horn relays, open circuit relay of motor or generator, regulating relays for charging voltage and current, flashing relays, control relays fro light brightness,control relays for air conditioning, and so on. The power supply in the car now mostly uses 12V, and the coil voltage is mostly set to be 12V. Due to the battery power supply, the voltage is unstable.  The environmental conditions are not good, for example, the suction voltage is less than 60VH (rated working voltage), and the overvoltage of the coil is required to 1.5VH. What’s more, the power consumption of the coil is relatively large, generally 1.6~2W, and the temperature rise is relatively high. Their environmental requirements are also quite harsh: the ambient temperature range is -40℃~100℃; the relay used in the engine box must be able to withstand the damage of sand, dust, water, salt, and oil; vibration and shock are undoubtedly affecting normal operation. 3.2 Household Appliance1) Air conditioning relays are mainly used to control compressor motors, fan motors and cooling pump motors to have control functions. Owing to the moment when the load starts, a large inrush current appears, which is about 6 times the full-load operating current. It takes a long time for the compressor motor to reach full speed (the power of the home appliance compressor motor is generally 1 to 3 horsepower, where the fan motor and cooling pump motor are 1/4 to 2 horsepower.), which is a serious threat to the relay contacts to eliminate as much as possible the contact bounce when the relay is sucked.  Because the relay is required to release fast, minimize contact bounce as much as possible. The safety requirements are also strict and must be recognized by a safety certification agency. For example, as for product environmental conditions, the ambient temperature requires -40 to 55℃, relative humidity up to 40%, 90RH, and have rainwater infiltration. Because weight and size are not important indicators, the relay is required to be robust and impact resistant.2) Relay used in washing machines, microwave ovens, electric heaters, etc. Relay contact load: the large load can reach 220V, 5000W heater (or 1 horsepower motor), and the small load can be as small as driving solenoids load, other relay coils load, indicator light load, etc. The expected life span of the relay is required to reach 5 to 10 years. That is to say, the electrical life of the relay is required to reach 105 times to 2×105 times. Ambient temperature: -40 to 55°C (85°C for microwave ovens and electric heaters); relative humidity 20 to 95%/RH. 3.3 Industrial RelaysIn industrial control, the main control function is completed by the universal AC relay. The relay is usually driven by a button or limit switch. It is also used in traffic signal controllers, temperature controllers, etc. The contacts of the relay can control solenoid valves, larger start motors, and indicator lights.  What’s more, the field of digital control has expanded the application of relays. Copy milling and coordinate boring are operated by data programming, and the signals are sent to the machine tool controller, memory unit and other logic elements to control 2 to 5 axes of the coordinate servo motor. With this mechanical control method, it is easy to control drilling machines, hexagonal lathes, ordinary lathes and automatic profiling machines.The digital control system requires the relay to have the ability to adapt to low-level signals, medium sensitivity, fast action and high switching reliability. The environmental conditions for the installation of industrial machinery must be considered. For instance, operating industrial machinery and surrounding equipment always transmit some shocks and vibrations to the control cabinet, and they also have the influence of splashing cutting coolant. So that these unfavorable environmental conditions must still be considered when selecting and designing relays. With strict safety requirements, high requirements are needed for electrical insulation, voltage resistance, and flame retardants. 3.4 Example Analysis: JYB-714 Liquid Level RelayLiquid level relay is a kind of relay that uses liquid level to control the circuit. To be specific, this is a relay with electronic circuits inside. Based on the conductivity of the liquid, when the liquid level reaches a certain height, the relay will act to cut off the power; when the liquid level is lower than a certain position, turn on the power to make the pump work.  To achieve the role of automated control, this control is composed of sensors and control actuators. According to the conductivity of water, but it is poor and cannot directly drive the relay. Therefore, there must be an electronic circuit to amplify the current to drive the relay to work. So the sensor of the liquid level controller is generally a wire. The line is divided into three types, high and low, and the middle line. The high is the water level overflow point to control the water level freely, in addition, the water will stop to fill in automatically. At the low water level, the low point is the automatic water filling point. Where the middle is constant contact.JYB-714 Liquid Level Relay①, ⑧ are the working power connecting terminals of the relay. ① is connected to L1, ⑧ is connected to N.②, ③, and ④ output the automatic control signal, and the working voltage of the output terminal is AC220V. ③ is the output signal common end, the level control signal of the water supply pump is output between ② and ③, and the drainage pump level control signal is output between ③ and ④.  ⑤, ⑥, ⑦ are the wiring terminals corresponding to the liquid level electrodes A, B, C in the pool.  ⑤ is connected to the high water level electrode A, ⑥ is connected to the low water level electrode B, and ⑦ connect to the lowest common electrode C. Note that in the experiment, the water inlet electrode uses a copper hard insulated wire of 1 to 1.5mm2, and the water inlet end is stripped of 5mm insulation. In addition, the safety voltage between the liquid level electrode terminals is DC24V. Tech Note1) Drainage type liquid level relay instructions"High" is the upper limit liquid level control point of the pool. When the water level rises to a high level, the water contacts the probe (electrode), and the controller automatically turns on the pump and starts to drain."Middle" is the lower limit liquid level control point of the pool. When the water level drops below the midpoint level, the water and the probe (electrode) are out of contact, and the controller automatically turns off the pump and stops draining."Low" is the ground line of the pool, the lowest point of the pool. 2) The difference between water-supply type liquid level relay and drainage-type liquid level relay:Water-supply type liquid level relay works in water shortage and stops when the water is full.The drainage-type relay works when water is full and stops in a water shortage.Figure 5. A RelayⅣ Relay Selection RulesTo use the relay well, the correct selection is very important. First of all, you must get a thorough understanding of characteristics and requirements of the controlled object, and have careful consideration. The principle, purpose, technical parameters, structural characteristics, specifications and models of the selected relays should be analyzed. On this basis, the relay should be correctly selected according to the actual situation and specific conditions of the project.1. The necessary conditions① The power supply voltage of the control circuit, the maximum current that can be provided.② Voltage and current in the controlled circuit. ③ Contact: When selecting a relay, on the one hand, you should consider whether the control circuit can provide enough working current, otherwise the pull-in of the relay is unstable. When the pull-in and release time of the relay cannot meet the requirements, the time constant of the coil loop can be changed to solve the problem. On the other hand, there is the elimination of electric sparks. Due to the small on-off current of the relay contacts, there will be no arc between the contacts, but "spark discharge" will occur. This is due to the presence of inductance in the contact circuit, and an overvoltage will appear on the inductance when it is disconnected. Together with power supply voltage on the contact gap, so that the contact gap will break down and discharge. Because of energy limitation, only spark discharge will generate. The alternating energy conversion between the capacitance and inductance existing between the contacts makes the spark looming and becoming a high-frequency signal. In addition, spark discharge will cause damage to the contacts, resulting in short service life. 2. After consulting the relevant materials to determine the conditions of use, you can find the relevant materials to find out the specific relay. If you already have a relay on hand, you can check whether it can be used according to the datasheet, and finally consider whether the size is appropriate. 3. Pay attention to the size of the appliance. If it is employed in general electrical appliances, in addition to the cabinet volume, small relays mainly consider the circuit board installation layout. For small electrical appliances, such as toys and remote control devices, ultra-small relay products should be used. 4. Rated load and service life are reference values, which will vary greatly according to different environmental factors, load properties and types. So it is better to confirm in actual or simulate actual use. 5. Try to use rectangular wave control for DC relays, and use sine wave control for AC relays. 6. In order to maintain the performance of the relay, please be careful not to drop the relay or subject it to strong shocks. 7. Do not use the relay in an environment with much dust and harmful gas. Harmful gases include gas containing sulfur, silicon, nitrogen oxides, etc. 8. As for the magnetic latching relay, it should be placed in the action or reset position as needed before use. 9. For polarized relays, please pay attention to the polarity of the coil voltage. 10. The relay is a heat-resistant component. High temperature can speed up the aging of the internal plastic and insulating materials of the relay. Contacts are oxidized and corroded, making it difficult to extinguish the arc. The technical parameters of the electrical components decay and the reliability reduces. So that good ventilation conditions should be maintained.And meanwhile, the low temperature cannot be ignored. Low temperature can aggravate the cold adhesion of the contacts and expose the contact surface. Many manufacturers’ relays indicate that the minimum temperature is -25°C, but high-voltage switches are also used in extreme cold. So it is recommended to leave the room when selecting the model to avoid the relay being unreliable due to low temperature. If circumstances permit, add heaters in the high cold area to ensure that the relay operates reliably and ensure the stability of the entire system. 11. Under the condition of low air pressure, the heat dissipation condition of the relay goes bad,  and the temperature of the coil rises, which changes the given pull-in and release parameters of the relay, affecting the normal operation of the relay. The low air pressure can also reduce the insulation resistance of the relay. It is difficult to extinguish the arc and is easy to melt the contacts and affect the reliability of the relay. It can be used normally at an altitude of fewer than 2000 meters, and it needs capacitance derated used at an altitude of more than 2000 meters. 12. Reduce the impact of mechanical stress on the relay. Mechanical force mainly refers to stress such as vibration, impact, and collision on the control system. The self-vibration of the circuit breaker in the high-voltage switch and the vibration caused by the opening and closing operations has a greater impact on the relay. An intermediate relay with a balanced armature mechanism should be selected. Electromagnetic relays have cantilevered beam structure, the natural frequency is low, oscillation and impact will cause resonance, resulting in the relay contact pressure to drop and contact instant disconnection or contact vibration, which will affect the reliability of the relay. It suggests that vibration measures should be taken to prevent resonance. Ⅴ One Question Related to DC Relay5.1 QuestionHow Does a DC relay work?5.2 AnswerA DC relay uses a single coil of wire wound around the iron core to make the electromagnet. When the DC coil is energized, the magnetism generated in the core is steady because the DC just keeps going. The steady magnetism keeps the lever attracted as long as the DC is flowing. Ⅵ Frequently Asked Questions about How Relay Works1. What is a relay and how it works?A relay is an electrically operated switch. They commonly use an electromagnet (coil) to operate their internal mechanical switching mechanism (contacts). When a relay contact is open, this will switch power ON for a circuit when the coil is activated. 2. Why relay is used?The switch may have any number of contacts in multiple contact forms, such as making contacts, break contacts or combinations thereof. Relays are used where it is necessary to control a circuit by an independent low-power signal, or where several circuits must be controlled by one signal. 3. How do you know if a relay is working?The only tool required to check a relay is a multimeter. With the relay removed from the fuse box, the multimeter set to measure DC voltage and the switch in the cab activated, first check to see if there are 12 volts at the 85 positions in the fuse box where the relay plugs in (or wherever the relay is located). 4. What is the main function of the relay?Relays are electric switches that use electromagnetism to convert small electrical stimuli into larger currents. These conversions occur when electrical inputs activate electromagnets to either form or break existing circuits. 5. What is the difference between relay and switch?The main difference between Relay and Switch is that the Relay is an electrically operated switch and Switch is an electrical component that can break an electrical circuit. ... Many relays use an electromagnet to mechanically operate a switch, but other operating principles are also used, such as solid-state relays. 6. Are Relays AC or DC?A Dc relay coil has a resistance that limits the dc current. An AC coil relies on its impedance for governing the current. An AC relay will remain contact closed due to mechanical inertia and a little mechanical hysteresis and, the fact that an alternating north and south pole both attract the relay armature. 7. How a relay works in a car?Although there are various relay designs, the ones most commonly found in low voltage auto and marine applications are electro-mechanical relays that work by activating an electromagnet to pull a set of contacts to make or break a circuit. These are used extensively throughout vehicle electrical systems. 8. What happens when a relay fails?If the ignition relay shorts burns out or otherwise fails while the engine is operating it will cut off power to the fuel pump and ignition system. ... In some instances of a faulty relay the vehicle will be able to restart once the relay cools off, only to stall out once again after the relay overheats. 9. Does a relay need constant power?The answer to that one is No. Relays have a finite lifetime in terms of how many times they can open and close. And limit to how much current they can handle. But keeping a relay constantly energized does not wear it out. 10. Why is a relay better than a switch?Relays are a better choice for switching large currents (> 5A). Relays can switch many contacts at once. Disadvantages of relays: • Relays are bulkier than transistors for switching small currents. Relays cannot switch rapidly (except reed relays), transistors can switch many times per second. Recommended ReadingBasic Knowledge of Relay Electronics Tutorial with VideoThe Role of the Relay and Its Working PrincipleThe Types of Common Relay and How to Choose Relay?
kynix On 2020-08-05   23510
Resistors

How to Test a Relay with Multimeter?

IntroductionA relay is an electronic control device, which has a control system (also called an input loop) and a controlled system (also called an output loop). It is often used in automatic control circuits. In fact, it is an automated switch using a smaller current to control a larger current. Therefore, it plays the role of automatic adjustment, safety protection, and converter in the circuit. Relay has the features of fast response speed, stable work, long service life and small size. In order to ensure that these performances can be better played, the test and maintenance of the relay (solid state relay) are particularly important. This paper will introduce main relay test parameters, how to test a relay, an example of an automotive relay test.Testing a RelayCatalogIntroductionⅠ Understanding Relays  1.1 Relay ParametersⅡ How to Test A Relay?  2.1 General Test Ideas  2.2 Types of Relay TestⅢ Relay for Life: Automotive Relay Test  3.1 Automotive Relay  3.2 Common Faults of Automotive Relays  3.3 Detection Method  3.4 Specific OperationⅣ One Question Related to Relay Test and Going Further  4.1 Question  4.2 AnswerⅤ Frequently Asked Questions about Relay TestⅠ Understanding Relays1.1 Relay ParametersMain relay parameters include rated working voltage, rated working current, coil resistance, contact load, etc.1) Rated working voltage refers to the voltage required by the coil when the relay is working normally. For DC relays it refers to DC voltage (Figure a), and for AC relays it refers to AC voltage (Figure b). Relays of the same type often have multiple assessed operating voltages for circuit requirements, and the specification number is added to the end of the component to distinguish.Figure 1. Relay Symbol2) The rated working current refers to the current required by the coil when the relay is working normally.Coil resistance refers to the DC resistance of the relay coil. When selecting a relay, you must ensure that it is rated working voltage and rated working current meet the requirements.Figure 2. Rated Working Current3) Contact load refers to the load capacity of the relay contact, also known as the contact capacity. For example, the contact load of the jzx-10m relay is:  DC 28v×2a or AC 115v×1a. When used, the voltage and current passing through the relay contact should not exceed the rated value, otherwise, the contact will be burned out and the relay will be damaged. A load of multiple sets of contacts of a relay is generally the same.Figure 3. Contact LoadRecommended Reading: Basic Knowledge of Relay Electronics Tutorial with Video    The Role of the Relay and Its Working Principle Ⅱ How to Test A Relay?Relays are widely used in power protection, automation, sport, remote control, measurement and communication devices, so it is very important to check and maintain the normal operation of relays. There are many types of relays. Therefore, the inspection of relays cannot only be judged by measuring the resistance value of the coil. It is necessary to adopt multiple detection methods according to different relay types.2.1 General Test Ideas1) measuring contact resistanceApply the specified working voltage to the relay coil, and use a multimeter to detect the on-off condition of the contact at the “R×1k” gear. When the power is not applied, the normally open contact does not work, and the normally closed contact conducts. When the power is turned on, you should be able to hear the pick-up sound of the relay. At this time, the normally open contact is conducting and the normally closed contact is opposite, and the switching contact should be switched accordingly. Otherwise, the relay is damaged. For multi-group contact relays, if some of the contacts are damaged, the remaining contacts can still be used.Figure 4. Relay Test 2) measuring coil resistanceThe resistance value of the relay coil can be measured with the multimeter at R×10Ω gear, so as to determine whether the coil is open. 3) measuring of pull-in voltage and currentUse an adjustable regulated power supply to input a set of voltage to the relay, and connect an ammeter in the power supply circuit to monitor. Increase the power supply voltage slowly, and when you hear the pull-in sound of the relay, write down the voltage and current. In order to be accurate, you can try several times to get the average value. 4) measuring the release voltage and currentSame test connection like the above. When the relay pulls in, then gradually reduce the supply voltage. When you hear the relay release sound again, write down the voltage and current at this time. Try several times to get the average release voltage and release current. Under normal circumstances, the release voltage of the relay is about 10-50% of the pull-in voltage. If the release voltage is too small (less than 1/10 of the pull-in voltage), it can't be used normally, which will affect the circuit stability resulting in abnormal operation. 2.2 Types of Relay TestElectromagnetic Relay TestFigure 5. Electromagnetic RelayThe multimeter is placed in the “R×100” or “R×1k” gear, and the two test leads (regardless of positive and negative) are connected to the two pins of the relay coil (shown in Figure 5). The indication of the multimeter should basically match the coil resistance of the relay. If the resistance value is obviously too small, it means that the coil is short-circuited locally; if the resistance value is 0, it means that there is a short circuit between the two coil pins; if the resistance value is infinite, it means that the coil is open or the pins are disconnected. Reed Relay TestReed relay is also one of the most commonly used relays. It consists of a reed switch and a coil, as shown in Figure 6. The reed switch is made by sealing two non-interconnected ferromagnetic metal strips in a glass tube, and the reed switch is placed in the coil. When the current passes through the coil, the magnetic field generated by the coil magnetizes the metal strips in the reed pipe, and the two metal strips attract due to opposite polarities to connect the controlled circuit. Several reed pipes can be placed in the coil, and they will act simultaneously under the action of the coil's magnetic field.Figure 6. Reed Relay Reed relay has a pair of coil pins and several pairs of reed switch pins, and there are corresponding marks on the shell for identification.Figure 7. Reed Relay Reed relays can also use a multimeter to detect their coils and contacts, and the detection method is the same as that of electromagnetic relays.Figure 8. Reed Relay Solid State Relay (SSR) TestThe input end can be tested with a multimeter. The multimeter is placed in the "R×10k" gear, the black test lead (the positive electrode of the battery in the meter) is connected to the positive electrode of the SSR input terminal, and the red test lead (that is, the negative electrode of the battery in the meter) is connected to the negative electrode of the input terminal of SSR. The hands should deflect more than halfway (Figure 9). Re-testing after swapping the two test leads, the hands should not move. If the needle deflects to the top or does not move regardless of the forward or reverse voltage access, the solid-state relay has been damaged.Figure 9. Solid State Relay  SSR You can also make a test circuit according to Figure 10. When the control voltage of the SSR input terminal is turned on, the light-emitting VD is on; when the control voltage of the SSR input terminal is cut off, the light-emitting diode VD is off.Figure 10. SSR Thermal Relay Test1) heating elements detectionThe heating element is composed of an electric heating wire or electric heating sheet, and its resistance is very small (close to 0Ω). The detection is shown in Figure 11. The normal resistance of the three groups of heating elements should be close to 0Ω. If the resistance is infinite (the digital multimeter displays the symbol "1" or "OL" for exceeding the range), the heating element is open.Figure 11. ① 200Ω gear is selected.② The red and black probes are respectively connected to the two ends of a heating element.③ The resistance is close to 0Ω, indicating that the resistor as a heating element is normal. 2) contact detectionThermal relays generally have a normally closed contact and a normally open contact. This detection includes working and non-working conditions. The first picture is the detection of the normally closed contact resistance when it is not in operation. Normally it should be close to 0Ω. Then the detection is taken in the opposite condition. Move the test rod, as shown in the second picture, simulates the over-current heating and bending of the heating element to make the contact action. The normally closed contact becomes an open circuit, and the resistance is infinite.Figure 12. ① 200Ω gear is selected.② The red and black probes are connected to both ends of the normally closed contact.③ The resistance is close to 0 Ω, indicating that the normally closed contact is closed.④ Move the test rod by hand.⑤ The out-of-range symbol "1" is displayed to indicate that the normally closed contact is open. Intermediate Relay TestThe electrical part of the intermediate relay is composed of coils and contacts, both of which use the resistance gear of a multimeter.1) The contact is detected when the control coil is not powered. Contacts include normally open contacts and normally closed contacts. When the control coil is power off, the normally open contacts are open and the resistance is infinite, at this time, the normally closed contacts are closed and the resistance is close to 0Ω. The above-mentioned detection of the normally open contact is shown in the figure below.Figure 13.① 200Ω gear is selected.② The red and black probes are connected to both ends of normally open contact.③ The out-of-range symbol "1" is displayed to indicate that the normally open contact is open. 2) Control coil detection of the intermediate relay is shown in Figure 14. Generally, the greater the rated current of the contact, the smaller the resistance of the control coil. This is because the greater the rated current of the contact, the larger the volume of the contact. Only a small control coil resistance (thicker line diameter) can flow through a larger current to produce a stronger magnetic field suction contact.Figure 14. ① 200Ω gear is selected for the gear switch.② Connect the red and black lead to the two pins of the control coil.③ The display of "6.60" indicates that the resistance of the control coil is 6.6kΩ.3) Power on the control coil to detect the contacts. Apply a rated voltage to the control coil, then use a multimeter to detect the resistance of the normally open and normally closed contacts. The normally open contact should be closed and the resistance should be close to 0Ω; the normally closed contact should be open and the resistance is infinite. Time Relay TestThe detection of time relay mainly includes contact normal state detection, coil detection and coil energization detection.1) Normal-state detection of contacts. It refers to the detection of the resistance of the contact when the control coil is not energized. The normally open contact is open and the resistance is infinite, while the normally closed contact is closed, and the resistance is close to 0Ω. Normal detection processes are shown in the figure below.Figure 15. ① 200Ω gear is selected for the gear switch.② The red and black lead is connected with two pins of a normally closed contact.③ The resistance is close to 0Ω, indicating that the normally closed contact is closed. 2) Detection of control coil. It is shown in Figure 16.Figure 16. ① 20kΩ gear is selected for the gear switch.② Connect the red and black lead to the two pins of the control coil.③ The display of "4.93" indicates that the resistance of the control coil is 4.93kΩ.3) Power on the control coil to detect the contacts. Apply a rated voltage to the control coil, then check whether the contact status has changed according to the characteristics of types of the time relay. For example, for a delay time relay, after a period of time delay, check whether the delay contact is closed (resistance is close to 0Ω) and whether the delay contact is disconnected (resistance is infinite).  Ⅲ Relay for Life: Automotive Relay Test3.1 Automotive RelayRelays are widely used in automotive circuits, such as starting system circuits, wiper circuits, and rear window heating circuits. When the vehicle starts, a larger starting current is required. If the ignition switch is used for direct control, the starting contacts will ignite and burn, which will affect the service life of the ignition switch and even cause serious consequences such as line ablation and fire. Using a relay to control a large current with a small current will not cause the above problems. When a certain voltage or current is applied to both ends of the electromagnetic relay coil, the magnetic flux generated by the coil passes through the magnetic circuit composed of the core, yoke, armature, and the working air gap of the magnetic circuit. Under the action of the magnetic field, the armature attracts the pole face of the iron core, making the normally closed contact opens and the normally open contact close. When the voltage or current at both ends of the coil is less than a certain value, the mechanical reaction force is greater than the electromagnetic attraction force, and the armature returns to the initial state: the normally closed contact is on and the normally open contact is off. One of the automobile relays functions is a switch; the other is load overload protection; the third is fault protection. 3.2 Common Faults of Automotive RelaysIncluding coil burnt, short circuit, insulation part aging, contact ablation, etc.1) Relay MalfunctionWhen the controlled circuit is required to be closed, the relay will not act, on the contrary, when the controlled circuit is not required to be closed, the relay will act. This kind of problem occurs mainly because the interference voltage in the circuit exceeds the allowable range of the drive circuit of the relay. When designing the circuit, pay attention to the factors that can cause interference (such as chip command errors, short circuits, grid fluctuations, etc.). 2) Relay BurnedThere are many reasons for burnout. For example, the actual switching current exceeds the rated switching current of the relay, and the actual inrush current exceeds the rated switching current of the relay. According to design experience, in order to avoid these problems, the rated current should be selected to be 2-3 times the actual switching current, and the impact current of the relay is 2-3 times the actual current. 3) Contact WeldingGenerally speaking, the temperature rise of the AC conversion relay coil is higher than that of the DC conversion relay. This is because of the eddy current loss and hysteresis loss in the magnetic circuit. In addition, when the AC conversion relay is operating at a voltage lower than the rated voltage, a bounce phenomenon may occur. This will cause burnout, welding of contacts and damage to the relay, or disconnection of the self-protection circuit. Therefore, measures must be taken to prevent fluctuations in the power supply voltage.In addition, regardless of the length of the fluctuation time, it will cause the failure of the relay. So ensure that there is a power supply with sufficient capacity. 4) Coil Temperature Rise is Too HighThe loss of magnetic materials such as copper wires and iron cores or the heat transfer of the contacts will cause the temperature rise. Therefore, the heat resistance of the insulating material and the distance between the relay and the heat-generating device should be paid special attention in the circuit design. 3.3 Detection MethodStatic detection: check the resistance of the coil and the resistance of the normally closed contact.Dynamic detection: energize the coil and detect the resistance of the normally open contact. 3.4 Specific OperationTurn on the ignition switch and hear whether there is a pull-in sound in the control relay or feel the relay with your hands for vibration. If so, it means that the relay is basically in routine. The failure of the circuit may be caused by other reasons. On the contrary, it means that the relay is faulty.Replace the relay to be tested with an identical working relay. Turn on the switch, and if the electrical equipment is working normally, it can be determined there is a problem with the relay to be tested.Use the multimeter Rx100Ω gear and combine the resistance of each pin of the circuit to analyze. If the conduction and disconnection are normal, it means that there is no problem with the relay, otherwise, it means the relay is faulty.Open the relay shell to check whether the contacts are ablated or oxidized. If there are bumps and rust on the contact, it means that the contact is ablated or oxidized and does not work properly.Check whether the coil is ablated or discolored. If the coil is ablated with jelly, the coil is black or has a gluey smell, which means the coil is short-circuited by ablation.Ⅳ One Question Related to Relay Test and Going Further4.1 QuestionWhat are the symptoms of a bad car relay?4.2 AnswerThe car suddenly stalls while operating. One of the most common symptoms of a failed ignition relay is a car that suddenly stalls while operating. Car not starting. Another symptom of a faulty ignition relay is a no-power condition.Dead battery. A dead battery is another symptom of a faulty ignition relay.Burned relay. Ⅴ Frequently Asked Questions about Relay Test1. How do you check if a relay is bad?The only tool required to check a relay is a multimeter. With the relay removed from the fuse box, the multimeter set to measure DC voltage and the switch in the cab activated, first check to see if there are 12 volts at the 85 positions in the fuse box where the relay plugs in (or wherever the relay is located). 2. How do you test a 12-volt relay? 3. How do you check an overload relay with a multimeter?CEP7 Overload Relay test proceduresMeasure the normal motor running current (i motor).Turn off the motor and let it cool for about 10 minutes.Calculate the following ratio: i (motor) / i (overload min FLA).Set the overload to its minimum FLA and turn on the motor.Wait for the overload to trip. 4. How do I test a solid-state relay?The SSR can be tested as described below if a load is connected. Connect a load and power supply, and check the voltage of the load terminals with the input ON and OFF. The output voltage will be close to the load power supply voltage with the SSR turned OFF. 5. Can a bad relay drain your battery?Battery drain or dead batteryA failed ECM power relay can also cause a battery drain or a dead battery. If the relay shorts, it can leave power on to the computer, even when the vehicle is turned off. This will place a parasitic drain on the battery, which will eventually cause it to go dead. 6. What happens when the main relay goes bad?The engine will not startIf the main relay is not supplying the engine computer with the power it needs, then the engine will not be able to crank and run the right way. Failing to get the main relay replaced will usually lead to the car being unusable. 7. How do you test a battery relay? 8. How do you test a protection relay?Protection relay self-test procedureThis will normally involve checking the relay watchdog circuit, exercising all digital inputs and outputs and checking that the relay analog inputs are within calibration by applying a test current or voltage. 9. How do you check if a relay is working?The only tool required to check a relay is a multimeter. With the relay removed from the fuse box, the multimeter set to measure DC voltage and the switch in the cab activated, first check to see if there are 12 volts at the 85 positions in the fuse box where the relay plugs in (or wherever the relay is located). 10. How do you test an electromagnetic relay?Grab a multimeter and set it to Ohms. Touch the leads across the electromagnet coil pins and measure resistance. Anywhere from 50-120 ohms is OK. Out of range or open means a bad electromagnet coil winding and time for a new relay.
kynix On 2020-07-29   15452
Resistors

Common Potentiometer Types and Applications Available

Executive Summary: Potentiometers in 2026A potentiometer (or "pot") is a three-terminal variable resistor used to control voltage, current, and signal processing in electronic circuits. While traditional mechanical pots remain vital for audio and industrial controls, 2026 trends favor high-precision Digital Potentiometers (DigiPots) and MEMS-based sensors for IoT and robotics applications. This guide covers the latest classification standards, modern applications, and essential maintenance tips for optimal circuit performance.Ⅰ. What is a Potentiometer? (2026 Overview)A potentiometer is a critical three-terminal passive electronic component that functions as an adjustable voltage divider. Ideally suited for applications requiring user-generated input or position sensing, it consists of a resistive element (track) and a sliding wiper. If only two terminals are configured (one end and the wiper), it functions as a variable resistor or rheostat. While the core mechanical construction of potentiometers remains consistent, modern 2026 manufacturing has introduced durable conductive plastics and cermet materials to extend lifecycle and precision.Figure 1: Potentiometer Basics and Modern ClassificationsⅡ. How are Potentiometers Classified?Potentiometers are primarily classified by their movement mechanism (Linear vs. Rotary) and their control method (Analog Mechanical vs. Digital). Understanding these distinctions is crucial for selecting components for 2026-era PCB designs.Table 1. Industry Standard Potentiometer Classifications (2026)Potentiometer TypeClassification Criteria & Modern StandardsBy Resistor MaterialElectrical performance relies on the track material. Common types include wire wound (high power), synthetic carbon film (consumer audio), metal glass glaze, and conductive plastic (high durability >1M cycles). Specialized types use metal foil or metal oxide film for precision aerospace applications.By Working Environment Selected based on IP ratings and stress factors: High-precision, high-resolution, high-power, or high-temperature variants. Modern sealed potentiometers are essential for automotive and outdoor IoT sensors.By Adjustable ResistanceIncludes fully adjustable (user interface), semi-adjustable (trimpots for calibration), and fine-adjustment types. Non-contact options (Hall Effect, Photo-electric) are gaining market share in 2026 to eliminate mechanical wear and "wiper noise."By Construction MechanicsRotary: Standard rotation is 270°–300°. Multi-turn: Uses a worm gear for 10-20 turns, vital for precision calibration.Linear Slider: Standard in audio mixing consoles for visual feedback of levels (faders). By Gang Number Single Gang: Controls one circuit.Dual/Ganged: Two pots on a single shaft, standard for stereo audio volume control to maintain channel balance.By Resistance Taper (Law)Linear (Type B): Resistance changes proportionally to angle. Used for voltage division.Logarithmic (Type A/Audio): Resistance changes logarithmically to match human hearing. Essential for volume controls.By Actuation MethodManual: Hand-turned knobs or sliders.Motorized: Equipped with a servo motor for remote control and "flying fader" automation in studio consoles. Ⅲ. Detailed Guide: Common Types & ApplicationsSelecting the right potentiometer requires understanding the trade-offs between mechanical endurance, noise levels, and precision.3.1 Breakdown of Key Potentiometer VarietiesRheostat (Variable Resistor)A rheostat functions strictly as a two-terminal variable resistor used to control current. While historically significant, in 2026, the term "rheostat" is considered legacy. Modern efficiency standards prefer PWM (Pulse Width Modulation) for current control over resistive rheostats, which dissipate excess energy as heat. However, they remain useful in simple educational circuits or rugged high-power calibration scenarios. Rotary PotentiometersThe rotary potentiometer is the most ubiquitous interface component. It features a resistive track (Carbon or Cermet) and a wiper connected to a rotating shaft. Key Specs: Typical tolerance is 10%-20%. Rotation is usually 270°. 2026 Applications: Smart home dial interfaces, car audio amplifiers, light dimmers (triac control), and older telecommunication equipment. Logarithmic (Audio) PotentiometersAlso known as "Audio Taper" pots. The resistance changes logarithmically to mirror the Weber-Fechner law of human hearing. At the start of rotation, resistance changes slowly; as the angle increases, the resistance shifts rapidly. This ensures that volume adjustments sound natural and linear to the human ear. Linear Potentiometers (Faders)In linear potentiometers (slide pots), the resistance varies directly with the physical distance the slider moves. They are indispensable in audio mixing consoles (EQ, Faders) because they provide immediate visual feedback of the setting. They are also used for precise voltage division in test equipment and battery internal resistance measurements. Digital Potentiometers (DigiPots)The 2026 Standard: Digital potentiometers are CMOS integrated circuits that replace mechanical wipers with digital switching networks. Controlled via protocols like I2C or SPI, they offer vibration immunity, zero mechanical wear, and programmable precision. Use Cases: Programmable gain amplifiers (PGAs), sensor calibration, LCD contrast control, and smart IoT devices where physical knobs are unnecessary. Membrane (Soft) PotentiometersConstructed by printing carbon/graphite onto a flexible substrate. When pressed, the top layer contacts the bottom resistive track. These are ultra-low profile and widely used in modern wearables, medical devices, and robotics tactile sensors. While they have lower accuracy than wirewound types, their form factor is unmatched for compact designs. Wirewound PotentiometersKnown for high power handling and thermal stability. A resistance wire is wrapped around an insulating core. Pros: High precision, high temperature tolerance. Cons: "Zipper noise" (resolution steps) and inductance issues at high frequencies. 3.2 Critical Application: Potentiometric Position SensorsPotentiometers remain one of the most cost-effective methods for measuring displacement in industrial machinery.3.2.1 Resistive Position SensorsThese function as passive transducers. By applying a stable reference voltage across the fixed terminals, the voltage at the wiper becomes directly proportional to the shaft's angle or linear position. They are widely used in joystick controls, valve positioning, and robotics joint feedback.Figure 2. Simple Position Sensor Circuit 3.2.2 Capacitive Position Sensors (Non-Contact Alternative)For environments where mechanical wear is a concern, capacitive sensors are the superior 2026 choice. They measure position by detecting changes in capacitance between a sensor plate and the target object. These are dominant in high-precision semiconductor manufacturing, touchscreens, and fluid level sensing where physical contact is impossible.Ⅳ. Best Practices: How to Use Potentiometers SafelyTo ensure longevity and signal integrity in your circuits, adhere to these maintenance and installation guidelines:Chemical Safety: Avoid exposing polycarbonate synthetic resin pots to ammonia, ketones, or high-acid chemicals, which degrade the housing.Flux Management: Do not use water-compatible fluxes. Poor quality soldering can lead to oxidation, causing "scratchy" audio or open circuits.Soldering Temp: Prevent heat damage. Pin terminals: 235°C ±5°C. Wire terminals: 350°C ±10°C. Keep solder >1.5mm from the body.Internal Contamination: Ensure no flux enters the internal mechanism during soldering to prevent contact noise.Voltage vs. Current: Potentiometers are designed for Voltage Division. Avoid using them as Rheostats (current limiters) for high loads, as the wiper contact resistance cannot handle high current.Moisture Control: Prevent condensation. In humid environments (like marine audio), use sealed or IP67-rated potentiometers.Mechanical Installation: Do not overtighten mounting nuts. For slide pots, ensure screw length doesn't penetrate the casing and jam the fader.Knob Assembly: Support the back of the shaft when pushing on knobs to prevent internal wiper collapse.Temperature Effects: Lubricant viscosity changes with temperature. For sub-zero applications, specify low-temperature grease to maintain smooth rotation.Signal Interference: Keep shafts/sliders short to minimize acting as an antenna for EMI (Electromagnetic Interference).Thermal Derating: Carbon film power ratings drop above 70°C. Ensure adequate ventilation. Ⅴ. Advanced FAQs and Industry Trends5.1 What are the primary potentiometer types?The industry divides them into Linear (Slide) and Rotary types. A third category, Digital Potentiometers (DigiPots), is now standard for automated systems, while Membrane "Soft Pots" serve ultra-thin form factors.5.2 Quick-Fire FAQsFrequently Asked Questions (2026 Updated)1. What is the main function of a potentiometer?It acts as a variable voltage divider to measure EMF, control volume/gain, or sense position. In 2026, it is also a key component in Human-Machine Interfaces (HMI). 2. What are the top 3 modern applications?User Interface: Volume and tone control in audio gear.Robotics: Position feedback servos (servo motors).Industrial: Linear displacement sensors in injection molding machines. 3. How does a potentiometer differ from a rotary encoder?Potentiometers are absolute position sensors (they know where they are on power-up) but have limited rotation. Encoders are digital, have infinite rotation, but typically require homing (calibration) on startup. 4. Why do audio pots use a logarithmic taper?Because human hearing is non-linear. A logarithmic taper matches the ear's sensitivity, creating a smooth perceived increase in volume.{ "@context": "https://schema.org", "@type": "TechArticle", "headline": "Potentiometer Ultimate Guide 2026: Types, Applications, and Selection", "datePublished": "2020-06-08", "dateModified": "2026-01-09", "description": "A comprehensive engineering guide to Potentiometers in 2026. Covers Linear vs Rotary, Digital Potentiometers, wiring diagrams, and maintenance tips for modern electronics.", "articleBody": "A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider...", "mainEntity": { "@type": "FAQPage", "mainEntity": [ { "@type": "Question", "name": "What are the main types of potentiometers?", "acceptedAnswer": { "@type": "Answer", "text": "The three main categories are Rotary Potentiometers (knobs), Linear Potentiometers (sliders/faders), and Digital Potentiometers (DigiPots) which use ICs for control." } }, { "@type": "Question", "name": "What is the difference between a potentiometer and a rheostat?", "acceptedAnswer": { "@type": "Answer", "text": "A potentiometer uses three terminals to divide voltage. A rheostat uses only two terminals (one fixed, one wiper) to restrict current. Modern circuits prefer potentiometers or PWM over rheostats for efficiency." } }, { "@type": "Question", "name": "Where are potentiometers used in 2026?", "acceptedAnswer": { "@type": "Answer", "text": "They are used in audio volume controls, robotic arm position sensing, industrial joystick controls, and as digital calibration trimmers in IoT devices." } } ] }}
Karty On 2020-06-18   15710
Resistors

Research and Application of Electronic Ballast Circuit Diagram

CategoryⅠ IntroductionⅡ Electronic Ballast Circuit Diagram Research Application 2.1 Overview 2.2 Circuit Structure of High-Performance Electronic Ballast       2.2.1 Power Factor Correction Circuit       2.2.2 Inverter Circuit       2.2.3 Lamp Circuit Network       2.2.4 Control Circuit2.3 High-Performance Electronic Ballast Dedicated Integrated Controller of ML4830 Series       2.3.1 Introduction to ML4831/32 Function       2.3.2 The Improvement of the Internal Function of ML48332.4 High-performance Electronic Ballast Built by ML4833Ⅲ FAQ Ⅰ IntroductionIn the 1970s, a worldwide energy crisis emerged. The urgency of energy conservation has led many companies to focus on energy-saving light sources and electronic ballasts for fluorescent lamps. With the rapid development of semiconductor technology, various high-return power switching devices are emerging, which provide conditions for the development of electronic ballasts. In the late 1970s, foreign manufacturers took the lead in launching the first generation of electronic ballasts, which was a major innovation in the history of lighting development. Because it has many advantages such as energy-saving, it has aroused great concern and interest around the world. It is considered to be an ideal product to replace the inductance ballast. Later, some well-known enterprises have invested considerable manpower and material resources to carry out higher-level research and development. Due to the rapid advancement of microelectronics technology, the development of electronic ballasts to high performance and high reliability has been promoted. Many semiconductor companies have introduced a series of products for dedicated power switching devices and control ICs. In 1984, Siemens developed an active power factor correction IC such as the TPA4812 with a power factor of 0.99. Subsequently, some companies have successively launched integrated electronic ballasts. In 1989, Finland's Hell Valley Company successfully launched electronically adjustable ballast monolithic integrated circuit ballasts. Electronic ballasts have been promoted and applied throughout the world, especially in developed countries. Figure 1. BallastChina's research and development of electronic ballasts started late, the technology is not advanced, early understanding of the difficulty and complexity of this product is insufficient, the development of special semiconductor devices has not kept up, the quality of products has not passed, and the market is extremely irregular. A large number of low-priced inferior goods were thrown to the market, causing losses to consumers and seriously damaging the image of electronic ballasts.  In the late 1990s, due to the rapid development and improvement of production levels, from circuit design to electronic components, the products entered a relatively mature stage, and high-quality products entered the construction project. The implementation of China's green lighting project paved the way for the promotion and application of electronic ballasts. Knowledge of Electronic Ballast for Fluorescent Lamps and Germicidal Lamps The electronic ballast is an electronic control device that uses a semiconductor electronic component to convert a direct current or low frequency alternating current voltage into a high frequency alternating current voltage, and drives a light source such as a low pressure gas discharge lamp (sterilization lamp) or a tungsten halogen lamp. The most widely used is the electronic ballast for fluorescent lamps. Due to the adoption of modern soft-switching inverter technology and advanced active power factor correction technology and electronic filtering measures, the electronic ballast has good electromagnetic compatibility and reduces the self-loss of the ballast. Ⅱ Electronic Ballast Circuit Diagram Research Application2.1 OverviewOn October 1, 1997, China's "Green Lighting Project" was officially launched. This is a major decision and measure in the field of lighting technology, which has a huge impact on China's energy, electric light source and lighting technology, and even environmental protection. As an important target of the "green lighting project", China will replace the incandescent lamp with an integrated energy-saving lamp composed of electronic ballasts and compact fluorescent lamps and promote more than 300 million energy-saving lamp, forming the terminal's ability to save 22 billion kWh, which is equivalent to saving about 49-63 billion yuan electricity construction funds. In addition to saving electricity, it can actually reduce social expenditures by 30-40 billion yuan. According to relevant experts from the Ministry of Information Industry, under the same luminous flux conditions, energy-saving lamps can save 80% of energy compared with incandescent lamps, and the cost of purchasing energy-saving lamps can be recovered in the 8-10 months of electricity savings. The use of electronic energy-saving lamps in ordinary households, enterprises and institutions, hotels, restaurants, and commercial systems is more cost-effective than incandescent lamps. However, the old-fashioned inductance ballasts currently working at the industrial frequency generally have the disadvantages of high energy consumption, low efficiency, large volume, and large amount of copper needed. Therefore, the state has set a policy which is to replace traditional inductance ballasts with high frequency electronic ballasts. Currently, some electronic ballasts have appeared on the market, and Table 1 lists the performance comparison of these electronic ballasts. According to the International Electrotechnical Commission standard IEC929 and China's professional standard ZBK74012-90, the electronic ballast should be used in "normal conditions, the lamp should be activated, but it does not cause damage to the lamp performance"; "The shortest time to apply the cathode preheating voltage should not be less than 0.4s" and "the crest factor of the open circuit voltage shall not exceed 1.8; during the minimum warm-up period, no extremely narrow voltage peaks that do not affect the rms value shall be generated", etc.  As listed in table 1, except for high grade electronic ballasts, they are unqualified products. In particular, as early as 1982, the International Electrotechnical Commission (IEC) developed a standard called “interference of household equipment and similar electrical equipment to the power supply system”, namely the IEC555-2 standard. In 1987, Europe also developed a similar EN60555-2 standard. Both standards strictly limit the power factor of the equipment to be close to 1, and it also clearly stated that, all products that do not meet the standards are not allowed to be sold. In view of the great harm caused by the low power factor, it is very important and necessary to impose regulations on the power factor of electronic equipment and products that must be close to 1. Figure 2. Brief Comparison of Low, Medium and High Grade Electronic Ballasts We believe that the high-performance electronic ballast should be a product that has both power factor correction and lamp filament preheating, lighting adjustment and lamp circuit protection, and is fully compliant with IEC555-2 and similar standards. The basic principles of the circuit structure and power factor correction circuit that must be provided for high-performance electronic ballasts are briefly discussed in this article. The integrated controllers for electronic ballasts ML4831, ML4832, ML4833 and high-performance electronic ballast circuits composed of them are highlighted. 2.2 Circuit Structure of High Performance Electronic BallastThe RFI and EMI filters in the figure filter out conducted RF interference and electromagnetic interference from the grid, while obstructing the conducted RF and electromagnetic interference generated by the ballast circuit from entering the grid. The bridge rectifier circuit converts the input AC to DC. The power factor correction circuit acts to improve the input AC current waveform, ensuring that the input current is sinusoidal and in phase with the input voltage, achieving a power factor close to or equal to one.  The inverter circuit completes the conversion of the DC high voltage to the high-frequency AC, and finally transmits the input power to the fluorescent tube through the lamp circuit network. In addition to transmitting electrical power, the lamp network will also perform preheating of the fluorescent filament, sampling and feedback of the lamp operating state signal. The feedback signal of the working state of the lamp is taken from the power factor correction circuit and the dimming signal, and processed by the control circuit to obtain the driving pulse of the switching device in the correct inverter circuit. 2.2.1 Power Factor Correction CircuitThe power factor of the system is defined as PF=γcosφ1 In the formula, γ=I1/IRMS, which is the ratio of the fundamental rms value of the input current to the rms value of the input total current and is also called the distortion factor of the current. φ1 is the phase shift angle of the fundamental current and voltage. If the input voltage of the system has no phase shift (ie, the system is purely resistive) and there is no harmonic component (ie DF=1), the PF of the system must be one. Unfortunately, the input rectification filter units that most of the current devices connect with the power frequency grid are composed of uncontrolled diodes and large-capacity electrolytic capacitors. The instantaneous value of the current on the grid side is quite high (generally about 2 to 3 times that of IRMS), the duration is very short (usually no more than 4ms), and it is severely non-sinusoidal, so the PF of the system is much lower than 1.  The power factor correction is aimed at the drawbacks of the traditional uncontrolled rectifier circuit, and adopts corresponding circuit measures. While increasing the DF value of the system, the phase shift of the input fundamental current and voltage is minimized, and finally the target with the PF value equal to 1 is achieved. As a boost-type active power factor correction circuit commonly used in electronic ballasts, the control circuit uses the input voltage signal as a reference, and the product of the input current and the output voltage signal is used as a modulation source to obtain a sinusoidal pulse width modulation (SPWM) signal to the step-up DC/DC power conversion circuit to adjust the on/off time ratio of the power switch. In the end, a stable DC high voltage is obtained.  The power switching device in the step-up power conversion circuit is driven by the SPWM signal outputted by the control circuit to turn on and off at a high speed, thereby ensuring that the current waveform flowing through the inductor connected in series with the rectifier bridge is a sine wave, and is in phase with the input voltage. Thus, the distortion factors γ=1 and φ1=0 of the system input current are obtained, that is, cosφ1=1, and the system power factor is 1. 2.2.2 Inverter CircuitThe most important function of the inverter circuit is to convert the high-voltage direct current outputted by the power factor correction circuit into a high-frequency alternating current for the fluorescent lamp. The power MOSFET push-pull tubes (V1 and V2) are alternately turned on and off under the driving pulse with a duty cycle of 50%, and is commutated when the current crosses zero in the parallel resonant loop of the power transformer primary inductance and capacitance thus to realize zero voltage switching(ZVS) and perform chopping on high voltage DC. The zero-voltage switching eliminates switching losses associated with output capacitance and parasitic capacitance charging of MOSFET tube, and the gate drive charge is minimal, which helps reduce gate losses.  Since the high frequency AC obtained by the secondary coupling of the power transformer is directly fed to the lamp network, there is no phase shift between the lamp current (ie, secondary current of the power transformer) and the output current of the inverter circuit (ie, primary current of the power transformer). Considering that the total impedance of the lamp network is reduced at high frequencies, and the negative resistance characteristic of the fluorescent lamp itself, it can be found that as the lamp current decreases (corresponding to the weakening of the light intensity of the lamp), the output current of the inverter circuit will increase. 2.2.3 Lamp Circuit NetworkThe lamp circuit network not only needs to deliver the high-frequency AC power to the lamp tube to complete the efficient conversion of electricity and light, but it also needs to implement functions such as filament warm-up, lamp current detection feedback, and auxiliary power supply for the entire electronic ballast system.  The power transformer primary T is connected to the inverter circuit, and the lamp current is directly transmitted to the lamp through the capacitor, and the secondary winding supplies the lamp with filament current for preheating and maintaining the operation. The current transformer TA performs detection and sensing of the lamp current, and sends a signal about the operation of the lamp to the control circuit at any time by the change of the lamp current. The control circuit can judge the light intensity of the lamp according to the magnitude of the lamp current (even including the disconnection and short circuit of the lamp), and then send corresponding control signals to the inverter circuit. 2.2.4 Control CircuitThe control circuit for high-performance electronic ballasts should have a series of functions including power factor correction, lighting adjustment, light-on preheating, lamp disconnection alarm, and lamp restart program control. At present, some integrated circuit controllers for electronic ballasts appearing in the domestic and international device market are mostly based on PFC control, with appropriate addition of lamp control functions, or implementation of lamp control by external circuits. It is worth mentioning that the ML4830/31/32/33 series products can be said to be integrated controllers for high-performance electronic ballasts. 2.3 High-Performance Electronic Ballast Dedicated Integrated Controller of ML4830 SeriesML4830/31/32/33 are integrated circuit controllers developed by American Micro Linear Corporation for high-performance electronic ballasts. The first generation ML4830 has been eliminated; the second generation ML4831 is manufactured by bipolar integrated circuit technology; the third generation ML4832 uses Bicmos process to replace the original bipolar process, the circuit bias current is greatly reduced, and the consumption is greatly reduced. The fourth-generation ML4833 not only adopts the Bicmos process but also has a major improvement in the internal structure, so the function is enhanced and the performance is better. Although these devices can use the functional block diagram of figure 3, the internal structure of ML4831 and ML4832 and the internal structure of ML4833 are respectively shown in figure 4 and figure 5. Figure 3. Functional Block Diagram of ML4831, 32, 33  Figure 4. Internal Block Diagram of ML4831, 32  Figure 5. Internal Structure Block Diagram of ML4833 2.3.1 Introduction to ML4831/32 FunctionThe ML4831/32 is composed of a continuous current type boosting power factor correction stage controlled by an average current. It has a dedicated control circuit for electronic ballasts with various ballast control links. Lamp start-up and restart timing can be achieved by using external circuit components to provide a wide range of control over different types of lamps. The ballast link uses an additional programmable method of frequency modulation and adjustment of the frequency range of the voltage-controlled oscillator to control the lamp power, so it is suitable for various types of output networks. The gain modulator in the ML4831/32 is highly immune to interference caused by switching high-power switching devices. The output of the gain modulator appears as a reference to the current error amplifier at the inverting input of the amplifier. Isine is the current drawn from the AC input; UEA is the output of the error amplifier (pin 1). The output of the gain modulator is limited to 1V. The PWM regulator in the PFC control section compensates for the positive voltage generated by the multiplier output through the negative voltage developed across the pin 4 sense resistor. At the same time, the power MOSFET is protected against high-speed current transients by weekly current limiting. Once the voltage at pin 4 is below 1V, the PWM cycle is terminated immediately. The overvoltage protection (OVP) terminal (pin 18) of the ML4831/32 is used to protect the power circuit from high voltage damage when the lamp is suddenly disconnected. The OVP take-off point can be set by directly tapping the voltage divider resistor to the high-voltage DC bus. As long as the voltage at pin 18 exceeds 2.75V, the power factor correction (PFC) transistor will be turned off and the ballast operation can continue.  The threshold of the OVP should be set to a value that the power device can operate safely, but is not too low to affect the operation of the boost power conversion link. The internal operational transconductance amplifier performs PFC voltage feedback, current sensing and loop amplification. The transconductance amplifier is designed with a low signal forward transconductance so that a large value resistor can be used as a load and a small (<1μF) ceramic capacitor for AC coupling in the compensation network. The compensation network can take the form of figure 6, introducing a zero point and a pole at frequencies fz and fP, respectively: fZ=1/2πR1C1fP=1/2πR1C2 It is noted that the DC-to-ground path and the output of the transconductance amplifier may be out of tune, and the offset error voltage value reflected at the input is determined by uos=iO/gm. Capacitor C1 in figure 6 is used to block DC and minimize the adverse effects of offset. All of the operational transconductance amplifiers in the ML4831/32 incorporate a Slew Rate enhancement to improve recovery under circuit power-up and transient response conditions because the transconductance amplifier changes from a small transconductance state to a large transconductance state. The response to large signals is essentially non-linear. Figure 6. Compensation Network for Transconductance Amplifier The ML4831/32 controls the output power of the lamp by frequency modulation of the non-overlapping conduction of the power switch tube in the inverter part of the ballast circuit. That is to say, during the discharge of oscillation timing capacitor CT, the output of both ballast power tubes is low. The frequency range of the voltage controlled oscillator (VCO) in the device is controlled by the output of the LFB amplifier (pin 6). As the lamp current decreases, the voltage at pin 6 rises, causing the CT charging current to drop, thus causing the oscillation frequency of the oscillator to become lower. Because the ballast output network attenuates high frequencies, the power fed to the lamp increases accordingly. In general, the frequency of the oscillator can be calculated as follows: fosc=1/(tchg+tdis) Attention: A zero charge current occurs when LFBOUT (pin 6) is high level. Typically, the charge current varies with the two inputs to the oscillator: One is the output of the warm-up timer, and the other is the output of the lamp feedback amplifier (pin 6). During the warm-up phase, the charging current is fixed at a value of Ichg (preheat) = 2.5 / Rset (3). During normal operation, the charging current varies with the voltage of pin 6 from 0 to UOH. When the voltage at pin 6 is zero, the oscillator frequency is lowest and the lamp power is maximum. The discharge current is much larger than the current flowing through the timing resistor RT. For example, when the discharge current is 5 mA, the discharge time is:  tdis ≈ 490 × CT. The ML4831/32 also includes a parallel regulator that limits the UCC voltage to 13.5V. When the UCC is 0.7V lower than 13.5V, the quiescent current of the device will be less than 1.7mA, and the output will be turned off, allowing the device to be started directly using the resistor attached to the rectified AC bus. In addition, because the ML4831/32 contains a temperature sensing function, the ballast operation is stopped as soon as the junction temperature of the device exceeds 120 °C. In order to better utilize the internal sensing function without using an external sensor, the position of the ML4831/32 must be carefully determined on the ballast's circuit board to ensure that the device can properly transfer the operating temperature of the ballast. The chip temperature of ML4831/32 can usually be estimated by the following formula:  Tj=65TA/PD(°C/W) It is worth noting that fully and reasonably using the sensing function inside the device is useful for reducing the total cost of the ballast. The starting scheme of the device is specifically designed for the ML4831/32 in accordance with the principle of ensuring the longest lamp life and minimizing the ballast heating. Figure 7(a) contains a starting scheme including preheating of the filament and sudden breaking of the lamp. When the ballast is energized, the time that the voltage on the CX rises from 0.7V to 3.4V is called the warm-up time of the filament.  During this time, the oscillator's charging current Ichg = 2.5/Rset, the oscillator produces a very high frequency, but does not produce a voltage sufficient to start the lamp. After the filament is preheated, the frequency of the inverter circuit drops to a minimum, and a high voltage is generated to start the lamp. If the voltage of the inverter circuit does not jump when the lamp should start to work, the lamp feedback voltage entering pin 9 will rise above Uref, the CX charging current will be bypassed, and the inverter circuit will stop working until CX drops to a 1.2V threshold by RX discharge. Stopping the inverter circuit in this way can avoid the failure of the lamp to start or the inverter circuit to overheat when it is disconnected from the socket.  In general, it is better to choose a large resistance RX to make this period longer. When CX reaches the 6.8V threshold, the oscillator will turn off LFBOUT, so the lamp will be driven to full power, then dimmed, and the potential of the CX pin is clamped at approximately 7.5V. The whole process is shown in the waveform of figure 7(b). Figure 7. Lamp Start Preheat and Interrupt Timing Scheme and Its Waveform 2.3.2 The Improvement of the Internal Function of ML4833The ML4833 is a modified version of the ML4831/32. In addition to the full functionality of the ML4831/32 described above, the most prominent improvement is in the power factor correction section. The power factor correction part of the ML4833 is a step-up type PFC control circuit for peak current sensing. This form of circuit only requires voltage loop compensation, which is simpler than the ML4831/32 with average current control mode circuit. It consists of a voltage error amplifier, a current sense amplifier without compensation, an integrator, a comparator, and a logic control circuit.  In the boost type power conversion part, the correction of the power factor is performed by the current sensing resistor to output the sensing voltage and the current flowing through, and the duty ratio is adjusted by comparing the integrated voltage signal of the error amplifier with the voltage across the Rsense. The control timing of the duty ratio is as shown in figure 8. Considering that all of the high-performance electronic ballast integrated control chips of Micro-Linearity are packaged in 18-pin DIP or SOIC packages, the improvement of the device structure will inevitably bring about changes in the internal functional frame and external pin functions. Figure 8. PEC Link and Duty Cycle Control of ML4833 2.4 High-performance Electronic Ballast Built by ML4833Figure 9 shows the complete circuit diagram of a high-performance electronic ballast built by ML4833. The circuit is a typical AC/DC/AC structure: the RFI suppression filter circuit is added to the input terminal, the booster active power factor correction circuit is composed of AC/DC in the front stage, and the high-frequency inverter circuit is composed of DC/AC in the rear stage. A closed-loop is formed through T5, VD11, R23 and pin 8 of the control to make the system works stably. Figure 9. Complete Circuit Diagram of High-performance Eectronic Ballast Built with ML4833  Ⅲ FAQ1. What is the use of electronic ballast?An electronic ballast will convert power frequency to a very high frequency to initialize the gas discharge process in Fluorescent Lamps – by controlling the voltage across the lamp and current through the lamp. 2. What is the output voltage of an electronic ballast?This unit operates off the AC mains with a voltage of 230 Volts and voltages generated within the unit can reach 600 to 800 Volts. 3. What is inside an electronic ballast?Lighting ballasts generate an initial high voltage to start the arc that excites the gases in fluorescent and HID lamps and makes them shine. ... Lighting ballasts for fluorescent light bulbs and HID lamps made before 1980 may contain polychlorinated biphenyls (PCBs). 4. How do you make an electronic ballast for tube light?An electrical ballast is nothing but a simple high current, mains voltage inductor made by winding number of turns of copper wire over the laminated iron core. Basically, as we all know a fluorescent tube requires a high initial current thrust to ignite and make the electrons flow connect in between its end filaments. 5. How do you wire an electronic ballast?Connect the ballast to the power from the breaker panel by wiring the black wire from the breaker panel to the black wire on the ballast, using a wire nut. Connect the white wire from the breaker to the white wire from the ballast. 6. What's the difference between electronic and magnetic ballast?A magnetic ballast uses coiled wire and creates magnetic fields to transform voltage. ... An electronic ballast uses solid-state components to transform voltage. It also changes the frequency of the power from 60 HZ to 20,000 HZ or higher depending on the ballast. 7. How do you test an electronic ballast with a multimeter?Insert one probe of the multimeter into the wire connector holding the white wires together. Touch the remaining probe to the ends of the blue, red and yellow wires leading from the ballast. Depending on the ballast, you may have only red and blue wires. 8. Are electronic ballasts non-linear loads?Rectified input, switching power supplies and electronic lighting ballasts are the most common single-phase non-linear loads. 9. Which is not the advantage of electronic ballast?Electronic ballasts are more efficient and more compact in size and weight. They also provide the ability for continuous power adjustment in different settings. A disadvantage is that power fluctuations may cause a failure but this can be offset by adding a buffer capacitor. The operation of the ballasts generates heat. 10. Can you repair an electronic ballast?I eventually replaced the 2 switching transistors in this ballast as well and it worked. So the next time you have a problem with an electronic ballast from a fluorescent fitting open it and check before buying a new one. They can be expensive and more often than not they can be repaired. 
kynix On 2020-01-16   3941
General electronic semiconductor

How to Read and Understand Schematics in Electrical? Basic Symbols Expressions

Introduction How to Read an Electrical Diagram Lesson What is a circuit Diagram? Circuit diagram is the basic of engineering research and planning. A schematic layout diagram, which is drawn with the standard symbol of physical electricity, can show the working principle of each component and device relationship, Each electronic component has a symbol. After seeing a few circuit diagrams, you’ll quickly learn how to distinguish the different symbols, and provide planning plan for installing electrons or electrical products. Circuit diagram is one of the basic skills that must be learned by electronic engineers. So this paper gathers the classical circuit materials related to regulated voltage power supply, DCDC conversion power supply, switching power supply, charging circuit, constant current source to provide the most practical circuit diagram reference for engineers. Schematic Symbols Basic Devices   A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.   An inductor, also called a coil, choke, or reactor, is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it. An inductor typically consists of an insulated wire wound into a coil around a core.     An electric battery is a device consisting of one or more electrochemical cells with external connections provided to power electrical devices such as flashlights, smartphones, and electric cars.[1] When a battery is supplying electric power, its positive terminal is the cathode and its negative terminal is the anode.[2] The terminal marked negative is the source of electrons that will flow through an external electric circuit to the positive terminal.       A relay is an electrically operated switch. Many relays use an electromagnet to mechanically operate a switch, but other operating principles are also used, such as solid-state relays. Relays are used where it is necessary to control a circuit by a separate low-power signal, or where several circuits must be controlled by one signal.           Five Parts to Understand Circuit Diagrams *Regulated Power Supply 1. The voltage adjustable range is between 3.5V~25V, the output current is large, using VR- tube circuit to obtain the stable output voltage. Working principle: after rectifying and filtering, DC voltage is supplied by R1 to the base of the adjusting tube, so that the adjusting tube can be switched on. When the voltage passes through the RP, R2 of the V1 conduction, V2 switched on, and then V3 is switched on. At this time, the emitter and collector voltage of V1, V2 and V3 do not change (it acts exactly like a voltage stabilizer). A stable output voltage can be obtained by adjusting RP, and the ratio of R1, PR, R2 to R3 determines the output voltage of the circuit. T: 80W~100W     Input: AC220VOutput Duplex Winding: AC28VRP: 1W (resistance: 250K~330K)FU1: 1A                FU2: 3A~5A VD1 | VD2: 6A02C4: 470µF/35V(electrolytic capacitor)C1: 3300µF / 35VC2 | C3: 0.1µF (MONO CAP)R1: 180~220Ω / 0.1W~1W     Fig 1. VR-tube Circuit 2. Regulated Voltage Adjustable Power Supply Circuit Diagram Whether the computer detection or electronic product can not be separated from the regulated power supply(RPS). This paper introduces one kind of RPS: a DC voltage continuously adjustable from 3V to 15V, the maximum current can be up to 10A, and the circuit uses a high precision standard voltage source integrated circuit (TL431) with temperature compensation which makes the voltage stabilizer more accurate. If there is no special requirement, it can basically meet the normal maintenance. The circuit is shown in the figure below. Fig 2. Regulated Voltage Adjustable Power Supply Circuit Diagram Its working principle is divided into two parts. The first part is a fixed 5V/1.5A power supply circuit; the second part is a high precision and large current regulator circuit which can be adjusted continuously from 3V to 15V. The first circuit is very simple. The DC voltage rectified by silicon bridge QL1 is filtered by C1 from the secondary 8V AC voltage of transformer, then the 5V three-terminal stabilizer block LM7805 can produce a fixed 5V | 1A power supply at the output end without any adjustment. This power supply can be used as an internal power source when the computer board is overhauled. The second part is basically the same as the common series power supply. The circuit is simple, the cost is low, but the voltage stabilizer performance is very high. The resistor R4, the regulator TL431, potentiometer R3 constitutes a continuously adjustable constant voltage source, which provides the reference voltage for the BG2 base. The regulated voltage value of the regulator TL431 is continuously adjustable, which determines the maximum output voltage of the power supply. If you want to expand the range of adjustable voltage, you can change the resistance values of R4 and R3, of course, the secondary voltage of transformer should also be increased. The power of the transformer can be controlled flexibly according to the output current, and the secondary voltage is about 15 V. Bridge rectifier QL, using 15A-20A silicon bridge, compact structure, fixed screws in the middle, can be directly fixed on the shell aluminum plate, better for heat sink. What adjusts the tube is the high current NPN metal shell silicon tube, because it has the very big heat, if the chassis allows, buying the big radiator as far as possible to expand the heat dissipation area; if does not need the big current, a smaller power silicon tube can be used to makes it smaller. The filter uses three 50V/4700uF electrolytic capacitance C5 and C7 in parallel, respectively, to make the output of large current more stable. In addition, this capacitor should be bought with a relatively larger volume, and those smaller ones will also mark 50V/4700uF, but the voltage fluctuates frequently, Or easy to fail for a long time lay idle. Finally, the power transformer can buy a ready-made switching power supply of more than 200W instead of the transformer. In this way, the voltage stability can be further improved, but the manufacturing cost is not too high, and other electronic components have no special requirements. After installation is completed, it can work properly without too much adjustment.   *Switched Power Supply(specific examples) The working principle of integrated control IC-UC3842 for PWM switching power supply The following is the UC3842 internal block diagram and pin diagram. UC3842 uses a fixed frequency pulse width controllable modulation mode, a total of 8 pins, each foot function as follows: Pin① is the output of the error amplifier, and the external resistor-capacitor unit is used to improve the gain and frequency characteristics of the error amplifier; Pin② is the feedback voltage input, which is compared with the 2.5 V reference voltage at the same phase of the error amplifier to generate the error voltage, thus controlling the pulse width; Pin③ is the current detection input, when detecting voltage exceeds 1V, the pulse width is reduced so that the power supply is in the state of intermittent operation; Pin④ is the timing end, the operating frequency of the internal oscillator is determined by the external resistor-capacitor time constant, f=1.8 / (RT×CT); Pin⑤ is the common ground; Pin⑦ is a DC power supply terminal with the function of undervoltage and overvoltage locking, the chip power consumption is 15mW. Pin⑧ is the output terminal of 5V reference voltage, its load capacity is 50mA. Fig 3. IC-UC3842 Electrical Diagram   UC3842 Internal Schematic Diagram UC3842 is an integrated controller of PWM switching power supply with excellent performance, wide application and simple structure. Because it has only one output, it is mainly used for voice control. The UC3842 pin7 is a voltage input with a starting voltage range of 16V-34V. When the power supply is on, the VCC is less than 16V, and the output of the Schmidt comparator is 0. At the same time, no reference voltage is generated and the circuit does not work. When Vcc > 16V, the input voltage Schmidt comparator sends out a high voltage to the 5V fern voltage regulator, which generates a 5V reference voltage. On the one hand, this voltage used in internal circuit; on the other hand, it provides a reference voltage to the outside through pin8. Once the Schmidt comparator flips to a high level (when the chip starts working), Vcc can change in the 10V-34V range without affecting circuit; when the Vcc is below 10V, the Schmidt comparator flips to a low level and the circuit stops working. When the reference voltage stabilizer has a 5V reference voltage output, the reference voltage detection logic comparator outputs a high level signal to the output circuit. At the same time, the oscillator will generate the oscillation signal of the f=Rt/Ct according to the parameters of the pin④ external Rt and Ct, which is added directly to the input of the totem pole circuit, the other is added to the position end of RS flip-flop made by PWM pulse width modulator, and the output end of R connects the output of current-detection comparator. The R-terminal is the control end of the duty ratio. When the R voltage rises, the Q pulse is widened. At the same time, the pulse width of pin⑥ is widened (duty cycle increased); when the R voltage drops, The Q pulse narrows and the pin⑥ pulse width becomes narrow (duty cycle reduced). The sequence of UC3842 points is as shown in the diagram. Only when the E point is in high level, and meanwhile, a point and b point is all in high level, the d point sends out the high level, the c point sends the low level, otherwise the d point sends the low level, c point sends out the high level. Pin② generally connects the feedback signal. When the pin②voltage increases, the pin① voltage will decrease, and the R-terminal voltage will also decrease, so the pin⑥ pulse will narrow, on the contrary, the pin⑥ pulse will become wider. Pin③ is a current sensing terminal. Usually, a small sample resistor is inserted into the source or emitter of the power transistor to convert the current passing through the switch to a voltage, and the voltage is introduced into the pin. When the load short circuit or other reasons cause the current of the power transistor to increase and the voltage on the sampling resistance exceeds 1V, the pulse output pin⑥ is stopped, which can effectively protect the power transistor from damage. Fig 4. UC3842 Internal Schematic Diagram TOP224P 12V | 20W Switching DC Power Supply Circuit Based on Regulated Voltage Two integrated circuits are used in the circuit: TOP224P three-terminal monolithic switching power supply (IC1) and PC817A linear optical coupler (IC2). After UR and Cl rectifier filter, AC power supply produces DC high voltage Ui, to supply primary winding of high frequency transformer T. VDz1 and VD1 can clamp the peak voltage of leakage inductance to the safe value and can attenuate the ringing voltage. VDz1 adopts P6KE200 type transient voltage suppressor with reverse breakdown voltage 200V, and VDl uses UF4005 type UFRD in 1A/600V. The secondary winding voltage is filtered by V, C2, L1 and C3 rectifier, getting 12V output voltage Uo. Uo value is set by the sum of the forward voltage drop UF, R1 of LED and the value of regulated voltage Uz2. Other output voltage values can be obtained by changing the turn ratio of high frequency transformer and the regulated voltage value of VDz2. R2 and VDz2 also provide a false load for 12V output to improve the load adjustment rate at light load. The feedback winding voltage is filtered by VD3 and C4 rectifier to supply the bias voltage required by TOP224P. Since the control current is regulated by R2 and VDz2, the output duty cycle is changed to stabilize the voltage. The common mode choke L2 can reduce the common mode leakage current generated by the waveform of the high voltage switch connected to the D by the primary winding. C7 is a protective capacitor used to filter out interference caused by coupling capacitors of primary and secondary windings. C6 can reduce the differential mode leakage current caused by the fundamental and harmonic waves of the primary winding current. C5 can not only filter the peak current added to the control terminal, but also determine the self-starting frequency, compensating the control loop with R1 and R3. Fig 5. TOP224P 12V | 20W Switching DC Power Supply Circuit The Main Technical Specifications of This Power Supply are as Follows AC Voltage: u=85~265V Voltage Regulation: η=78% Grid Frequency: fLl=47~440Hz Input Voltage (Io=1.67A): Uo=12V Working Temperature: TA=0~50℃ Maximum Output Current: IOM=1.67A Maximum Output Ripple Voltage: ±60mV Continuous Power Output: Po=20W /TA=25℃ or 15W /TA=50℃)   *DC-DC Power Supply 3V→+5V or +12V Circuit Portable electronic products powered by batteries generally use low power supply voltage, which can reduce the number of batteries and product size. In order to ensure the stability and accuracy of the circuit, it is necessary to use a regulated power supply. If the circuit uses 5V working voltage, but one component requires a higher working voltage, this often makes the designer feeling hard. In this paper, a circuit composed of two booster modules is introduced to solve this problem, and only two batteries are used to supply power. The circuit has fewer components, small size, light weight, stable output of 5V or 12V, and meets the requirements of portable electronic products. +5V power supply can output 60mA, and +12 V power supply maximum output current is 5 mA. Fig 6. 3V→+5V or +12V Circuit The circuit is shown above. It is composed of AH805 and FP106 booster module. AH805 is a kind of boost module with an input of 1.2V~3V and an output of 5V, which can output 100mA current at 3V. FP106 is a chip boost module with input of 4V~6V and output fixed voltage of 29 ±1V, the output current up to 40 mA.  AH805 and FP106 are both a level-controlled to shut down the power. The output voltage of two 1.5V alkaline batteries is 3V, inputting to the AH805, and its output voltage is 5V, inputting 5V to the FP106, and the output voltage is 28V~30V, and then the output voltage is 12 V after through the voltage stabilizer. It can be seen from the diagram that different output voltages can be obtained by changing the stabilizer voltage. Pin⑤ of FP106 is the closing end of controlling the power supply. When Pin⑤ is added a high level > 2.5V, the power supply is switched on; When adding the low level is less than 0.4V, the power supply is off. It can be controlled by circuit or manually. If it is not necessary, Pin⑤ is connected to Pin⑧. MC34063 3.6V→9V Circuit Working State: No-load: Output 3.65V| 18uA  Load: Output 9.88V | 50.2mA; Input 3.65V | 186.7mA, efficiency 72% Working Principle: When there is no load, the IC has no power on pin⑥ and stops working. The input current is only 18uA with input 3.65V. When there is a load (Q1 has Ieb current), the EC pole of 8550 is switched on and the IC is operating. Whether the IC works is determined by whether there is a load or not, it is quite a battery. Using IC has a high voltage conversion efficiency and output stably. If this circuit adds a point of improvement, for example, when increasing power, it can turn into a power supply from 4.2V to 5V without switch. You can use a battery box as a backup power source for your phone. Fig 7. MC34063 3.6V→9V Circuit   *Charging Circuit lm358 basic Battery Charger Circuit Diagram Fig 8. lm358 basic Battery Charger Circuit Diagram There are two different arguments about whether alkaline batteries can be recharged. Some can be filled; the other say it has a risk of explosion. In fact, alkaline batteries can be rechargeable, generally 30-50 times of its service life. In fact, due to the charging methods, there are two different consequences. First of all, there is no doubt that alkaline batteries can be rechargeable, and in the battery instructions, it is mentioned that alkaline batteries are not rechargeable and that charging can lead to explosions. That's true, but note that the word is "could". Actually, it can be viewed as a manufacturer's self-protection statement of exemption. The key to charging alkaline batteries is temperature. As long as you can charge the battery without high temperature, you can successfully do it. The right charging method requires several points: small current: 50mA  charge 1.7V  discharge 1.3V After some people tried charging practice, they said categorically that they could not recharge. The reason for the problems such as lack of charging, short electricity consumption, leakage, explosion, actually, most are charger problems. If the charging current of the charger is too large, far more than 50 ma, and some fast chargers is above 200ma, the direct result is that the temperature of the battery is very high. If the battery is hot, the batteries will leak, and the serious will explode. Some people use Ni-MH rechargeable battery charger to charge, low grade charger does not automatically stop charging function, after long time charging will lead to overcharge then causing battery leakage and explosion. A better charger has the function of automatic shutdown, but the stop charge voltage is generally set to 1.42 V of the Ni-MH rechargeable battery, while the voltage of the alkaline battery is about 1.7V when it fully charged. As a result, the voltage is too low which causing fake charge. And not to wait until the battery is completely out of power to charge, it will lead to poor lifetime of the battery. It is recommended that the voltage of alkaline battery is not less than 1.3V. Therefore, if you plan to charge the alkaline battery, you must have a qualified charger, charging current around 50mA, and charging cut-off voltage is about 1.7V.   Related Description Alkaline manganese rechargeable battery: based on alkaline zinc manganese battery, it is also called mercury-free alkaline manganese battery because of the use of mercury-free zinc powder and new additives. The battery can be recharged for dozens to hundreds of times without changing the discharge characteristics of the alkaline battery, which is more economical. Alkaline zinc-manganese battery was developed in 1882. It was developed in 1912 and put into production in 1949. It has been found that when KOH electrolyte solution replaces NH4Cl as electrolyte, both the electrolyte and the structure change greatly, its performance improved significantly. Features Open voltage is 1.5V Working temperature is between -20℃ to 60℃, it is suitable in alpine region. The capacity of high current continuous discharge is about 5 times that of acid zinc-manganese battery. 2.75W USB Charger This design adopts Power Integrations's LinkSwitch series product LNK613DG. This design is well suited for mobile phones or similar USB charger applications, including mobile phone battery chargers, USB chargers, or any application with constant voltage or constant current. In the circuit, the diode D1 to D4 rectifies the AC input, and the capacitors C1 and C2 filter the DC. The L1, C1 and C2 form a π type filter to attenuate the differential mode conduction EMI noise. These are connected by E-sheild technology of Power Integrations transformers. This design can easily meet the requirements of EN55022 B-type conduction EMI with sufficient margin, and no Y capacitor is required. Fire proof, fusible, winding resistor RF1 provides fault protection and limits surge current generated during startup. Fig 9. 2.75W USB Charger Circuit Fig 9 shows that U1 is powered by optional offset power, which reduces no-load power to less than 40 mW. The value of by-pass capacitance C4 determines the number of cable voltage drop compensation. The value of 1μF corresponds to the compensation of a 0.3Ω / 24 AWG USB output cable. (10μF capacitance compensates 0.49 Ω / 26 AWG USB output cable.). In the constant voltage stage, the output voltage is regulated by switch control. The output voltage is maintained by skipping the switching cycle. By adjusting the ratio of the prohibition period to maintain voltage regularly. This also optimizes the efficiency of the converter throughout the load range. Under the condition of light load (trickle charge), the current limit will be decreased to reduce the magnetic flux density of the transformer, thus reducing the audio noise and switching loss. With the increase of load current, the current limit will increase, and the skipping period will be reduced continuously. When no longer skipping any switching period (maximum power point), the controller in the LinkSwitch-II switches to constant current mode. When the load current needs to be further increased, the output voltage will decrease, and it reflects in the FB pin voltage. In response to the voltage drop of the FB pin, the switching frequency will decrease linearly to achieve constant current output. The RCD-R clamping circuit is composed of D5, R2, R3 and C3, which is used to limit the leakage voltage spike caused by leakage inductance. Resistance R3 has a relatively large value to avoid drain voltage waveform oscillations caused by leakage inductance, which prevents excessive oscillation during turn-off, thus reducing EMI conduction. Diode D7 rectifies secondary and C7 filters it. C6 and R7 together limit the transient voltage spike on D7 and reduce EMI conduction and radiation. The resistor R8 and Zener diode VR1 form an false output load which ensures that the output voltage is within an acceptable limit and that the battery does not discharge completely when the charger is off. Feedback resistors R5 and R6 set maximum operating frequency and output voltage at constant voltage stage.   *Constant-Current Source 1. Discussion on How to Design Three-wire Constant Current Source Driving Circuit The constant current source drive circuit is responsible for driving the temperature sensor Pt1000, to convert its sensing resistive signal with temperature into measurable voltage signal. In this system, the required constant current source should have good temperature stability, large output resistance, output current less than 0.5mA (upper limit of Pt1000 without self-heating effect), earthing at one end of load, and variable polarity of output current. Because the influence of temperature on the parameters of integrated operational amplifier is less significant than of the transistor or FET, the constant current source composed of integrated operational amplifier has the advantages of better stability and higher constant current performance. Especially in the case where one end of the load needs grounding, it has been widely used. So use the dual operational amplifier constant current source shown in figure 2. Amplifier UA1 is used as adder, UA2 as follower, UA1 and UA2 are gain bipolar operational amplifier OP07,  which having low noise, low misalignment and high open-loop. Fig 10. Three-wire Constant Current Source Driving Circuit Vb and Va are the up and down potential of the reference resistor Rref in figure 2: Va is the output of in-phase adder UA1. When taking the resistor R1= R2 , R3=R4, the output current of the Va=VREFx+Vb. It can be seen that the dual operational amplifier constant-current source has the following remarkable characteristics: Load earthing The output current is bipolar when the operational amplifier is supplied by a dual power source. The constant current can be achieved by changing the input reference VREF or adjusting the reference resistor Rref0. It is easy to obtain stable small current and compensation calibration. Because of the mismatch of the resistor, the voltage at both ends of the reference resistance Rref0 will be affected by the terminal voltage Vb of its driving load. At the same time, as a constant current source, Vb will definitely change with the load, which will affect the stability of the constant current source. Therefore, the four resistors R1, R2, R3, R4 are chosen according to the principle that the mismatch should be as small as possible, in addition, the mismatch direction of each pair of resistors should be consistent. In practice, a large number of precision resistors of the same batch can be screened, and 4 resistors with close resistance values can be selected. 2. High Voltage Constant Current Source Circuit Diagram(switch power model) The instrument needs a constant current source that can generate 1mA current on 0 to 3 megabytes ohmic resistance. A design composed with 12V storage battery and UC3845 has be made: the transformer uses a color TV high voltage packet, in which L1 enamelled wire is wound 24 turns on the core of the original high voltage package; L3 uses a coil of the original high voltage package and L2 with the high voltage part of the high voltage packet; L3 and LM393 constitute a voltage limiting circuit which limits the output voltage too high and adjusts the open-circuit output voltage by adjusting R10. Fig 11. High Voltage Constant Current Source Circuit Diagram(switch power model) You May Also Like Filtering Circuit Tutorial (Schematic Diagrams) Switch Mode Power Supply Circuit Design Tutorial Selection Guidance of Five Main Materials for Flexible Circuit Board Production Recommendation MC34063A SOP8 LM7805A UC3842AD   FAQ 1. What are the basic elements of electronics?When building electronic circuits, you will work with a number of basic electronic components, including resistors, capacitors, diodes, transistors, inductors and integrated circuits.   2. What is the schematic symbol represented in the electrical and electronic diagram?It is also called a schematic symbol. Each component has typical functionality according to its operational characteristics. An electronic circuit or schematic drawing uses a wired path between electronic components to complete the circuit. These components are represented by respective symbols for it.   3. What are the 5 components of electricity?The Basics of Electrical ComponentsResistors. The very first component that you should know about is the resistor.CapacitorsLight Emitting Diode (LED)TransistorsInductorsIntegrated Circuit (IC)   4. What are the types of electronics?Electronics has branches as follows:Digital electronicsAnalogue electronicsMicroelectronicsCircuit designIntegrated circuitsPower electronicsOptoelectronicsSemiconductor devices   5. What are the different schematic symbols?Schematic Symbols:Wires (Connected)Wires (Not Connected)DC Supply VoltageGroundNo Connection (nc)ResistorCapacitor, Polarized (Electrolytic)Light-Emitting Diode (LED)   6. What are the electrical diagrams?Image result for Electrical DiagramElectrical diagrams are drawings which are used to represent electrical circuits, these circuits are represented by using lines, symbols, and number combinations. Electrical diagrams show the wiring between components and the relative position of the components.   7. What are the three types of electrical diagrams?There are three ways to show electrical circuits. They are wiring, schematic, and pictorial diagrams. The two most commonly used are the wiring diagram and the schematic diagram.    8. What are the four types of electrical diagram?Image result for Electrical DiagramSome of these electrical drawings or diagrams have been described below.Block DiagramSchematics Circuit DiagramSingle Line Diagram or One-line DiagramWiring DiagramPictorial DiagramLadder Diagram or Line DiagramLogic DiagramRiser Diagram   9. What are the 2 main types of electricity?Current electricity is a constant flow of electrons. There are two kinds of current electricity: direct current (DC) and alternating current (AC).   10. What are the 2 types of electric circuit?Types of Electric CircuitsThere are two types of circuits found in homes and other common devices; namely series circuits and parallel circuits.   11. What is electrical block diagram?Block Diagram – A block diagram shows the major components of electrical or mechanical interrelations in block, or square or rectangular, form. The lines between the blocks represent the connections between the systems or components.   12. What are the 4 basic components of a circuit?Every electric circuit, regardless of where it is or how large or small it is, has four basic parts: an energy source (AC or DC), a conductor (wire), an electrical load (device), and at least one controller (switch). Visualize what happens when you switch on a room light.   13. What is type of wiring diagram?Schematic Diagrams often called a ladder diagram, is intended to be the simplest form of an electrical circuit. This diagram shows the circuit components on horizontal lines without regard to their physical location. It is used for troubleshooting because it is easy to understand the operation of the circuit.   14. What is the main purpose of electrical diagram?Electrical drawings, sometimes referred to as wiring diagrams, are a type of technical drawing that provide visual representation describing electrical systems or circuits. They are used to explain the design to electricians or other workers who will use them to help install or repair electrical systems.   15. Which software is used for electrical design?Top 8 Software For Electrical EngineersAutoCAD ElectricalPLC ProgrammingSCADA SoftwareAC/DC Drive SoftwareProteus And PspiceOrCADXilinxKeil
kynix On 2018-11-23   4781
Amplifiers

Detailed Explanation of Nine Simple Audio Amplifier Circuit Design Schematic Diagram

In this article today, we will introduce 9 simple audio amplifier circuit design schematic diagram with detailed explanation, complemented with some knowledge about amplifier.     Catalog   I. What is an Audio Amplifier? II. Nine Simple Audio Amplifier Circuit Design Schematic Diagrams III. Some Knowledge about Amplifier FAQ     I. What is an Audio Amplifier? Let's watch a video first. This video shows us how to make a great sounding LM386 audio amplifier with bass boost An audio amplifier is a device that reconstructs an input audio signal on an output element that produces sound. The reconstructed signal volume and power level are ideal. They are truthful, effective, and low distortion. The audio range is from 20Hz to 20 kHz, so the amplifier must have a good frequency response within this range. Depending on the application, the power varies greatly. From milliwatts of headphones to several watts of TV or PC audio, to dozens of watts of mini home stereo and car audio, to hundreds of watts or more of more powerful household and commercial audio systems, until the power is big enough to meet the sound requirements of an entire cinema or auditorium.   The development of audio amplifiers has gone through three times. They are electron tube (vacuum tube) time, bipolar transistor time, and field-effect transistor time. The electronic tube audio amplifier has a round and sweet timbre, but it has the disadvantages of large volume, high power consumption, unstable operation, and poor high-frequency response. For the bipolar transistor audio amplifier, it has the advantages of a wide frequency band, large dynamic range, high reliability, long life, and high-frequency response is good. However, its static power consumption and on-resistance are very large, and the efficiency is difficult to improve. The third one is the field-effect transistor audio amplifier. It has the same round and sweet timbre as the electron tube and its dynamic range is wide. More importantly, it has a small on-resistance and can achieve high efficiency. Figure 1 II. Nine Simple Audio Amplifier Circuit Design Schematic Diagrams Next, I would like to introduce nine simple audio amplifier circuit design schematic diagrams.   Circuit Diagram 1 This circuit makes full use of the conventional LM317 voltage adjustment chip,  so that it not only completes the voltage stabilization function of the unstabilized voltage after filtering but also realizes the function of amplifying the audio signal picked up by the electret capacitive microphone. The electret capacitive microphone contains an impedance converter based on JFET, which converts the speech signal into a current form and adds it to the RP resistor, causing the corresponding voltage change. 220V AC output 36V unstable DC through transformer and bridge rectifier, and after filtering by the capacitor, the low resistance audio amplification signal input by the LM317 on the DC is fed into the capacitor and output to the loudspeaker. The implementation circuit is shown in figure 2.   Figure 2 After the circuit is installed, the voltage difference between the two inputs of the electret capacitive microphone should be adjusted first. This voltage difference is required to be less than 1.25VDC. By connecting an adjustable resistor between the LM317 adjustment end and the ground, the required limit can be achieved by adjusting the resistance by Rp. Secondly, the audio signal picked up by the microphone is easy to be interfered with by external noise. The addition of C1 can filter out part of the interference signal, but the required signal is also attenuated. Because the internal gain of the LM317 can compensate for the attenuation part, the loss caused by the introduction of C1 is negligible.    In order to avoid excessive loss, the capacity of C1 should be as low as possible, this circuit takes 15F. Finally, it should be noted that the minimum operating current requirement of the LM317 chip is 4 mA when the circuit is working normally, and a load resistor is used to absorb the 4mA current. If a low impedance loudspeaker is used, this load resistance must also be introduced to compensate for the signal distortion. In a practical circuit, if an 8Q impedance loudspeaker is used, at least 420Q load resistance is used to compensate for the possible signal distortion.   Circuit Diagram 2 Figure 3     Circuit Diagram 3 Adjust R1 so that the signal is not distorted at the maximum output, and reduce R2 to output more power. If there is a multimeter, the collector voltage of the transistor can be adjusted to about half of the power supply voltage. Figure 4     Circuit Diagram 4 In this design, the gain control of the preamplifier adopts DC volume control mode is realized as shown in figure 5. The preamplifier is an inverse proportional amplifier composed of a fully differential operational amplifier and resistor. Its gain is determined by the ratio of feedback resistance to input resistance. The external input DC analog control signal Vc is converted into control data through the gain control module (GainCon-troD), which is used to control the ratio of the feedback resistance of the preamplifier to the input resistance, and then adjust the change of the gain. Figure 5   The operational amplifier adopts a two-cascade structure, as shown in figure 6. In the first stage, a folded common-source common-gate amplifier with PMOS input is used to provide a large gain. At the same time, the common-mode range of the input is increased and the flicker noise is reduced. The load of the folded input tube adopts a current source load with a source feedback structure to increase the output impedance and reduce noise. The second stage uses a common-source amplifier to provide a large swing.    In order to maintain the stability of the closed-loop, Miller compensation capacitance is added. At the same time, in order to counteract the influence of the zero points of the right half-plane, the zero adjusting resistance in series with the compensation capacitor is inserted into the feedforward path of the compensation capacitor. In the design of the common-mode feedback circuit, the common-mode feedback structure with resistance distributor and amplifier is adopted.     Figure 6   Circuit Diagram 5 The audio amplifier uses very few peripheral components and works well at 2v. (The circuit is shown in figure 7)   The TDA7052 is a mono amplifier designed for battery-powered portable tape recorders and radios with an internal gain set at 40dB. Now the recorder and radio tend to be miniaturized and the battery consumption is reduced, which means that the power supply voltage is reduced, and the output power is also reduced. In order to compensate for this loss, TDA7052 uses the bridge drive load (ETL) principle, which can make the output power of 8 EU load up to 1.2 w.   Figure 7 lists the working parameters of TDA7052. Except for special instructions, the power supply is 6 v, the load impedance is 80, the input signal frequency is 1 kHz and the ambient temperature is 25 degrees.   Figure 7   Circuit Diagram 6   TDA2822 Fabrication of microphone Power Amplifier Circuit The circuit has few peripheral components, simple fabrication, but surprisingly good sound quality. A dual audio amplifier integrated circuit is used and its main characteristics are high efficiency and low power consumption. The typical value of static working current is only about 6mA. The integrated circuit has strong voltage adaptability (from1.8V to 15V DC) and will still have a power output of about 100mW even if it is used at a low voltage of 1.8V. The specific circuit is shown in figure 8. Figure 8   The electret microphone MIC converts the picked sound signal into an electrical signal, which is introduced from the foot 2 of U1 by C2 and W, and amplified by U1 audio to promote the loudspeaker pronunciation. The machine is connected with a BTL output circuit, which is good for improving sound quality and reducing distortion. At the same time, the output power is increased fourfold. When a 3v voltage is used, the output power is 350mW.   The resistance R1 and R2 are 1/4W metal film resistance, W is a small carbon film potentiometer and C2 is preferably a monolithic capacitor. If there is no good quality ceramic capacitance, select high quality, voltage resistant, and low leakage current electrolytic capacitor for C1, C4, and C3. Choose high sensitivity electret microphone as MIC, choose small button switch or toggle switch for K and choose TDA2822M or TDA2822 or D2822 for U1. According to the numerical value in figure 7, it can work normally without debugging.     Electret microphone detection For example, the R*100 of MF 47 multimeter is used to measure the Great Wall CZ Ⅲ electret microphone. When the black watch pen is connected to the core line and shell of the electret microphone, the multimeter pointer refers to the value at 3k Ω. When blowing hard, the pointer refers to the value at 4k Ω (and the resistance value of some microphones becomes smaller). If you blowhard and the multimeter pointer wobbles very little, you can adjust the two watch pens and try again. If the multimeter needle is still wobbling very little, the electret microphone is damaged.   In application, the drain D of the electret microphone must be connected to the positive electrode of the power supply through a resistance of 4.7 to 10k Ω, and then connected to the amplifier circuit, as shown in figure 9. Figure 9   Circuit Diagram 7    Add an amplifying circuit to the microphone  The electronic components are as follows:                                                                    resistance R1:1k Ω resistance R2:1m Ω resistance R3:1k Ω transistor vT:9014 capacitance:4.7 UF capacitance C2 :4.7 UF battery:AA size battery     Figure 10    Working principle of amplifier circuit  Fig. 10 is a circuit diagram of the entire microphone amplifier circuit. As you can see from fig. 10, there are only six or seven originals of the whole circuit. The following is a brief description of how it works, in which the resistor R1 is responsible for providing the operating voltage to the microphone, R2 and R3 are responsible for providing the bias voltage for the transistor, and the capacitor C1 is responsible for coupling the signal of the microphone to the transistor for amplification. Finally, the amplified signal is coupled through capacitance C2 and sent back to the positive pole of the microphone line, that is, the outermost shielding layer of the microphone line (that is, the outer layer of copper mesh). Figure 10 is the material or electronic component we use to make it.    Considerations in production  The specifications of the electronic components required for the whole amplifier circuit are as follows: resistance R1:1K Ω resistance R2 :1m Ω resistance R3 : 1K Ω transistor VT :9014 capacitance C1:4.7 μ F capacitance C2 :4.7 μ F battery: a general AA size battery. △ Generally speaking, it can be used for about half a year if it is used normally.    Pay attention to the following points in the production process: 1. The pin of the transistor must be connected correctly; otherwise, it will not play the role of amplification. The pin distinguishes the following transistors lead down and the flat side facing itself. The transistors are E (emitter), B (base), and C (collector);   2. The microphone head is also polar. (see figure 4 for a specific distinction);   3. The polarity of the coupling capacitance can be distinguished by marking, and the pin with an arrow and marked "-" is a negative electrode, and the positive electrode is generally not marked   Because the components are few or can be directly welded in the shed, the circuit board can be directly installed into the base of the microphone, and the power lead of the circuit board can be connected to the battery slot reserved by the microphone.     Effect Test After trial, the effective distance of the microphone can reach 5 to 6 meters, and the effect is also obvious with the voice input function of Office Word 2003, and the speech can also be accurately recognized about 1 meter away from the microphone.   Circuit Diagram 8 A transistor is required. First, output the MP3 signal and use a lower power tube to amplify it. Then push medium power tube. This can achieve small distortion and have the coupling undone. This transistor circuit is simple, practical, and also easy to make.     Figure 11 The circuit is powered by a 9V single power supply. The input signal is coupled to the base of 9014 through 47uF capacitance. 9014 is responsible for preamplifier, and works in Class A state. 5.6K and 1.5K resistors are bias resistors of 9014, and 5.6K resistors are negative feedback resistors at the same time. 22 Ω resistors is a current series negative feedback resistor, which is used to increase the input impedance and reduce the linear distortion by 9014. The 470 Ω resistor is a 9014 collector load resistor used to convert the 9014 amplified current into a voltage, and two 1N4148 diodes are used to set the post-stage complementary tube in the pre-conduction region. OTL complementary output circuit is composed of 8050 and 8550. 3.3 Ω resistors are negative feedback resistors in series with emitters, which act the same as 22 Ω resistors. The 1000uf capacitor is the output capacitor, which is used to separate the DC and allow the AC signal to pass through. 8050 and 8550 are used as power output tubes to form a complementary push-pull output circuit, and the amplified current of 9014 is further amplified to push the loudspeaker. The static bias current of the push-pull circuit is set by two 1N4148, and the two 1N4148 are temperature compensation elements of two power output transistors at the same time. The voltage at the positive contact of the 1000uF electrolytic capacitor shall be half of the supply voltage. Because the conduction voltage of the silicon transistor base is 0.7 V, the base voltage of 8050 can be obtained to be about 5.2 V. From this, the static bias current of 9014 is (9- 5.2) / 470 =8 [mA]. The emitter voltage of 9014 is 8*22=0.176 V, and the base voltage is 0.176+0.7≈0.87V. Circuit Diagram 9 As long as R3 is increased, the gain of the amplifier can be increased. The parallel capacitor C4 at both ends of R3 is used to provide low resistance path filtering to high frequency to prevent high frequency self-excitation. J1 is a jumper, when J1 is turned on, foot 1 is grounded and the full power amplifier works; when J1 is disconnected, foot 1 is VDD, micro-power off, and the amplifier does not work. Jumper J2 can also control the operation of the amplifier. When J2 is disconnected, the + IN end is unbiased and the amplifier does not work. But if it is connected,  the amplifier works. LM4819 high gain audio amplifier circuit is shown in figure 12. Figure 12   III. Some Knowledge about Amplifier      Distortion  Also referred to as THD+N, Total Harmonic Distortion + Noise is simply a measure of the effect that an amplifier will have on sound output. The lower the distortion is, the closer your amp’s output will be to the original recording’s sound. The more distortion that there is, the more coloration there will be to the sound. Just keep in mind that your speakers will also have an impact upon sound, so choose them wisely by matching them with the right amplifier for the clearest sound.    Left and Right Signals  Crosstalk is a term that refers to the measure of how much of the right signal is mixed with the left signal. Amps come as a single unit, but they need to send signals out separately to the speakers so that you can hear things like a piano on the right and a singer to the left. If there is a lot of crosstalk, though, it will be much more difficult to decipher where the different sounds are coming from.    Power  When you look at an amp’s specs, you will also notice that there is a number for the power output, which is basically how loud the music can go. For the average listener, a 10W amp would be sufficient, as it will let you play your music loudly without creating any distortion. If you are really looking for a super loud amp, though, you can go as high as 100W. It really depends upon what your preferences are, what you will be using your amp for, what speakers you have, and how much room you have.    Connections  Your amp should have plenty of inputs for anything and everything that you wish to plug into it. You could have a 3.5mm connection for your iPod, and you could have a USB connection for your laptop, as a couple of examples. Just don’t sacrifice sound quality for more inputs.    Signal vs. Noise  There will always be some background noise within your amplifier, just as there is always some background noise in your own environment. What you want is an amp that will ensure the background noise is not obvious or perceptible. This will ensure that you will hear all of the music but none of the noise. Checking the signal to noise ratio on an amp will give you clearer insight into how well the product will work in this area.   FAQ   1. What does an audio amplifier do? An audio power amplifier (or power amp) is an electronic amplifier that amplifies low-power electronic audio signals such as the signal from radio receiver or electric guitar pickup to a level that is high enough for driving loudspeakers or headphones.   2. What is the difference between a speaker and an amplifier? Speakers are those things that make sound. The amplifier is what delivers sound to the speakers. Amps are usually radios and speakers are what you plug into the amp/receiver to hear the sound. ... The speakers plug into the sound card which in this case would loosly be called the amplifier.   3. Does amplifier improve sound quality? An amplifier simply increases(magnifies)the components of sound quality. If the quality of the input sound is poor, it will be a louder poor sound ; meaning you will hear the poorness of the sound more. It amplifies everything, the good and the bad.   4. Why do you need an amplifier? An amplifier is the device that turns the low voltage signals from your source equipment into a signal with enough gain to be used to power a pair of speakers. ... The second does the 'heavy lifting' and adds the gain to the signals in order to be used to power a pair of speakers. This is the power amplifier.   5. Which is better amplifier or receiver? A receiver is definitely the more convenient choice of the two, but that doesn't mean that it comes without any downsides. Usually a Lower Quality Amplifier - Though the quality of receiver amps is definitely increasing, you still don't have a completely dedicated amp with a receiver.   6. Which is more important speaker or amplifier? A speakers performance is highly variable and its sound will depend on the amp driving it. But the greatest amp (whatever that is) will sound like crap if the speaker sounds like crap. The quality of the speaker is the ultimate limitation of your system (assuming proper set up and room integration)   7. Can I hook up 8 ohm speakers to a 4 ohm amplifier? Yes, you can use 8 ohm speakers with a 4 ohm amplifier. Just wire two 8 ohm speakers of the same wattage in parallel.   8. How much money should I spend on an amp? If it's just for practicing in your bedroom, you can get a perfectly adequate little practice amp for under $200. If you'll be playing in a band or gigging out, yeah, you probably should expect to spend in the $500-700 range at least.   9. Do you need an amp for a subwoofer? Subwoofers are designed to increase the bass frequencies, resulting in a deep, thumping sound. In most cases, they are paired with an amplifier to boost the sound. If you do not have the funds for both components, you can still hook up a subwoofer without an amplifier; it simply involves a little more know-how.   10. Which transistor is used in amplifier? In most of the electronic circuits, we use commonly NPN transistor configuration which is known as NPN transistor amplifier circuit. Let us consider a voltage divider biasing circuit which is commonly known as a single stage transistor amplifier circuit.     Reference Component LM3886TF LM4652TA LM4765T  
kynix On 2017-08-18   2864

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.