The Kynix Blog

Tokyo Tech researchers demonstrate operation energy-savings in a low price silicon power transistor structure by scaling down in all three dimensions. In electronics, lower power consumption leads to operation cost savings, environmental benefits and the convenience advantages from longer running devices. While progress in energy efficiencies has been reported with alternative materials such as SiC and GaN, energy-savings in the standard inexpensive and widely used silicon devices are still keenly sought.K Tsutsui at Tokyo Institute of Technology and colleagues in Japan have now shown that by scaling down size parameters in all three dimensions their device they can achieve significant energy savings.Tsutsui and colleagues studied silicon insulated gate bipolar transistors (IGBTs), a fast-operating switch that features in a number of every day appliances. While the efficiency of IGBTs is good, reducing the ON resistance, or the voltage from collector to emitter required for saturation (Vce(sat)), could help increase the energy efficiency of these devices further.Previous investigations have highlighted that increases in the “injection enhancement (IE) effect”, which give rise to more charge carriers, leads to a reduction in Vce(sat). Although this has been achieved by reducing the mesa width in the device structure, the mesa resistance was thereby increased as well.Reducing the mesa height could help counter the increased resistance but is prone to impeding the (IE) effect. Instead the researchers reduced the mesa width, gate length, and the oxide thickness in the MOSFET to increase the IE effect and so reduce Vce(sat) from 1.70 to 1.26 V. With these alterations the researchers also used a reduced gate voltage, which has advantages for CMOS integration.They conclude, “It was experimentally confirmed for the first time that significant Vce(sat) reduction can be achieved by scaling the IGBT both in the lateral and vertical dimensions with a decrease in the gate voltage.”These are three terminal devices used as switches or rectifiers. With simple gate-drive characteristics and high-current and low-saturation-voltage capabilities they combine the benefits of two other types of transistors - metal-oxide-semiconductor field effect transistors (MOSFETs) and bipolar transistors.The researchers reduced the mesa width, gate length, and the oxide thickness in the MOSFET by a factor of 1/k, and compared devices with values of 1 and 3 for k. Because the fabrication of narrow mesas can cause problems they also reduced the trench depth by 1/k.Although this has a slightly negative effect on the IE effect, it has considerable benefits for fabrication ease and cost and the dependence of (Vce(sat)) on the trench depth was deemed to be small. The gate voltage was also decreased by a factor of 1/k, while the cell pitch was maintained at 16 μm.Reference:2SA1987C4706FJA4213RTU

A capacitive touch sensor display that provides a more intuitive interface to ease and accelerate user interactions has been developed by VCC. The LED-based CTH series capacitive touch sensor display combines graphic interactive control with colour identification to make the interface more user-friendly.Utilising sensitive capacitive touch sensing technology, the CTH series simplifies designs and offers cost savings by eliminating the need for a traditional switch.The LED display produces a high-optical clarity, and is offered with or without a wide variety of standard graphic overlays and colours. VCC can also develop custom icons to meet most any application requirement. Offered in a wide variety of colours including red, yellow, blue, pure green and white, the LED back-lit CTH series. The robust design has no moving parts, improving reliability and increasing the operational life.Featuring a through hole design, the capacitive touch sensor display is available in one standard size 15x15x11.0mm with an industry standard pitch of 0.100"."Featuring translucent icons illuminated with different coloured LEDs, the user friendly CTH series display offers superior device interaction by communicating a singular action to users such as on/off, alarm status, and more," said Sannah Vinding, Director of Product Development and Marketing at VCC. "The integrated functionality of the compact CTH series capacitive touch sensor display eliminates the need for designing-in a traditional switch. Unlike mechanical membrane switches or mechanical push buttons, capacitive touch keypads have no moving parts so there is nothing to wear out."The CTH series is used in a wide range of applications including appliances, consumer equipment, gaming devices, industrial control displays, media players, medical devices, mobile communication devices, PDAs, point of sale terminals, portable instruments, touch screen monitors and more.Reference:T141AM61STMPE1208SQTRQT1101-ISGAT42QT2100-AUR  

In an advance that helps pave the way for next-generation electronics and computing technologies—and possibly paper-thin gadgets —scientists with the U.S. Department of Energy's Lawrence Berkeley National Laboratory (Berkeley Lab) developed a way to chemically assemble transistors and circuits that are only a few atoms thick. What's more, their method yields functional structures at a scale large enough to begin thinking about real-world applications and commercial scalability. The scientists controlled the synthesis of a transistor in which narrow channels were etched onto conducting graphene, and a semiconducting material called a transition-metal dichalcogenide, or TMDC, was seeded in the blank channels. Both of these materials are single-layered crystals and atomically thin, so the two-part assembly yielded electronic structures that are essentially two-dimensional. In addition, the synthesis is able to cover an area a few centimeters long and a few millimeters wide. "This is a big step toward a scalable and repeatable way to build atomically thin electronics or pack more computing power in a smaller area," says Xiang Zhang, a senior scientist in Berkeley Lab's Materials Sciences Division who led the study. Zhang also holds the Ernest S. Kuh Endowed Chair at the University of California (UC) Berkeley and is a member of the Kavli Energy NanoSciences Institute at Berkeley. Other scientists who contributed to the research include Mervin Zhao, Yu Ye, Yang Xia, Hanyu Zhu, Siqi Wang, and Yuan Wang from UC Berkeley as well as Yimo Han and David Muller from Cornell University. Their work is part of a new wave of research aimed at keeping pace with Moore's Law, which holds that the number of transistors in an integrated circuit doubles approximately every two years. In order to keep this pace, scientists predict that integrated electronics will soon require transistors that measure less than ten nanometers in length. Transistors are electronic switches, so they need to be able to turn on and off, which is a characteristic of semiconductors. However, at the nanometer scale, silicon transistors likely won't be a good option. That's because silicon is a bulk material, and as electronics made from silicon become smaller and smaller, their performance as switches dramatically decreases, which is a major roadblock for future electronics. Researchers have looked to two-dimensional crystals that are only one molecule thick as alternative materials to keep up with Moore's Law. These crystals aren't subject to the constraints of silicon. In this vein, the Berkeley Lab scientists developed a way to seed a single-layered semiconductor, in this case the TMDC molybdenum disulfide (MoS2), into channels lithographically etched within a sheet of conducting graphene. The two atomic sheets meet to form nanometer-scale junctions that enable graphene to efficiently inject current into the MoS2. These junctions make atomically thin transistors. "This approach allows for the chemical assembly of electronic circuits, using two-dimensional materials, which show improved performance compared to using traditional metals to inject current into TMDCs," says Mervin Zhao, a lead author and Ph.D. student in Zhang's group at Berkeley Lab and UC Berkeley. Optical and electron microscopy images, and spectroscopic mapping, confirmed various aspects related to the successful formation and functionality of the two-dimensional transistors. In addition, the scientists demonstrated the applicability of the structure by assembling it into the logic circuitry of an inverter. This further underscores the technology's ability to lay the foundation for a chemically assembled atomic computer, the scientists say. "Both of these two-dimensional crystals have been synthesized in the wafer scale in a way that is compatible with current semiconductor manufacturing. By integrating our technique with other growth systems, it's possible that future computing can be done completely with atomically thin crystals," says Zhao. Reference: 2N3811 EMX2T2R DMA204020R  

Type 1 diabetes patients may one day be able to monitor their blood glucose levels and even control their insulin infusions via a transparent sensor on a contact lens, a new Oregon State University study suggests.The sensor uses a nanostructured transistor – specifically an amorphous indium gallium oxide field effect transistor, or IGZO FET – that can detect subtle glucose changes in physiological buffer solutions, such as the tear fluid in eyes.Type 1 diabetes, formerly known as juvenile diabetes, can lead to serious health complications unless glucose levels are carefully controlled. Problems can include retinopathy, blindness, neuropathy, kidney and cardiac disease.Researchers in the OSU College of Engineering say sensors they fabricated using the IGZO FET will be able to transmit real-time glucose information to a wearable pump that delivers the hormones needed to regulate blood sugar: insulin and glucagon.The sensor and pump would, in effect, act as an artificial pancreas."We have fully transparent sensors that are working," said Greg Herman, an OSU professor of chemical engineering and corresponding author on this study. "What we want to do next is fully develop the communication aspect, and we want to use the entire contact lens as real estate for sensing and communications electronics."We can integrate an array of sensors into the lens and also test for other things: stress hormones, uric acid, pressure sensing for glaucoma, and things like that. We can monitor many compounds in tears – and since the sensor is transparent, it doesn't obstruct vision; more real estate is available for sensing on the contact lens."The FET's closely packed, hexagonal, nanostructured network resulted from complimentary patterning techniques that have the potential for low-cost fabrication. Those techniques include colloidal nanolithography and electrohydrodynamic printing, or e-jet, which is somewhat like an inkjet printer that creates much finer drop sizes and works with biological materials instead of ink.The findings by postdoctoral scholar Xiaosong Du, visiting scholar Yajuan Li and,Herman were recently published online in the journal Nanoscale. The Juvenile Diabetes Research Foundation provided primary funding for the research.Google has been working on a glucose-monitoring contact lens but its version is not fully transparent."It's an amperometric sensor and you can see the chips—that means it has to be off to the side of the contact lens," Herman said. "Another issue is the signal is dependent on the size of the sensor and you can only make it so small or you won't be able to get a usable signal. With an FET sensor, you can actually make it smaller and enhance the output signal by doing this."This research builds on earlier work by Herman and other OSU engineers that developed a glucose sensor that could be wrapped around a catheter, such as one used to administer insulin from a pump."A lot of type 1 diabetics don't wear a pump," Herman said. "Many are still managing with blood droplets on glucose strips, then using self-injection. Even with the contact lens, someone could still manage their diabetes with self-injection. The sensor could communicate with your phone to warn you if your glucose was high or low."The transparent FET sensors, Herman said, might ultimately be used for cancer detection, by sensing characteristic biomarkers of cancer risk. Their high sensitivity could also measure things such as pulse rate, oxygen levels, and other aspects of health monitoring that require precise control.Reference:OP913SLBPW41NBPW20RFPD204-6C 

It takes a very, very clean room to build a detector sensitive enough to see the light from the beginning of the universe.Work is underway at the U.S. Department of Energy's (DOE's) Argonne National Laboratory on a new "clean room." The new lab will be specially suited for building parts for ultra-sensitive detectors—such as those to carry out improved X-ray research, or for the South Pole Telescope to search for light from the early days of the universe."This will be a unique facility, and a wonderful investment for the future of the laboratory," said Supratik Guha, who heads the Center for Nanoscale Materials, a DOE Office of Science User Facility adjacent to where the new space will be located.Clean rooms are a special kind of laboratory that is heavily filtered and cleaned, so that no free-floating particles interfere with delicate work. Take a cube of air one foot on a side: In a normal room in your house or office, this cube contains about one million free-floating particles of dust, dirt and other materials. In the clean room, it's no more than 100.This environment is what you need to build detectors that can detect the tiniest amount of energy striking the surface."Even a few stray specks of dust in the niobium can throw off the design for these detectors," said Marcel Demarteau, who heads the High Energy Physics Division at Argonne and will be a key user of the new lab.One use for such detectors is in the South Pole Telescope in Antarctica, one of several telescopes searching for light waves that have traveled throughout the universe since the moments after the Big Bang. This kind of light is called the Cosmic Microwave Background radiation.Because the light has traveled across space for the 13.8 billion years since the universe began, it has encountered all sorts of obstacles that slightly change its power spectrum—galaxy clusters, patches of dark matter, even our own atmosphere. "We have to correct for these to map the Cosmic Microwave Background signature we're looking for, but these small perturbations themselves hold an enormous amount of very valuable information about the composition of the universe," Demarteau said.  The most sensitive instruments today to find such signals are detectors made from superconductors. Superconductors are extremely sensitive materials that change properties dramatically when their temperature is raised even a tiny bit, and scientists can build components that react to specific frequencies to detect the signature of the Cosmic Microwave Background. The new clean room should allow researchers to build even more sensitive detectors—think of a camera that takes 150-pixel pictures versus one that can take 500,000-pixel images.The same technology will also offer researchers a chance to get better close-ups of the atomic makeup of objects being studied at the Advanced Photon Source, a DOE Office of Science User Facility at Argonne where scientists use X-rays to study everything from car fuel injectors to proteins that play roles in disease.The Advanced Photon Source sends beams of high-energy X-rays at a sample of whatever scientists are studying: a new solar cell material, a sample of volcanic glass from Greenland, a protein involved in photosynthesis. The X-rays hit the sample and scatter off in all directions. Very sensitive detectors pick up that scatter and reveal the chemical and atomic layout of the sample. The better the detector, the more information you can get; so Advanced Photon Source scientists are always looking for new ways to improve those detectors."The type of detector we want to build, nobody makes commercially: so we have to build our own," said Thomas Cecil, an engineer with the Advanced Photon Source. The new clean room will allow them to experiment with new kinds of transition edge sensors, which he said they hope could eventually improve the sensitivity by one or even two orders of magnitude compared to traditional silicon-based detectors.Building such technology is an excruciatingly delicate process, in which they lay down multiple coatings just a few nanometers thick—less than a hundredth of the diameter of a human hair—of superconducting materials and etch patterns into them. Then they repeat the process all over again, for up to 15 layers.The detector itself is so precise that it's operated at temperatures colder than outer space to achieve maximum sensitivity. "It's an excellent opportunity for us to push the boundaries of what's possible," Cecil said.Other potential uses, Demarteau said, include quantum computing as well as homeland security: building detectors that can pick out the particular signature of a specific kind of radiation, to detect if terrorists are carrying a dirty bomb made out of, for example, cesium-137. 

A group of researchers at Osaka University, succeeded in producing nanostructured gas sensor devices for detecting volatile organic compounds (VOC) in breath for the purpose of healthcare in time equivalent to or shorter than one tenth of the time required for manufacturing conventional gas sensors. This group improved conventional complicated production methods, developing a simple production method of just sintering substrates applied with materials. This gas sensor's sensing response was comparable to the top-of-the-line sensors reported all over the world.Research leading detection of low concentrations of gas present in exhaled human breath to health checkups and early detection and treatment of serious diseases is being performed. As gas sensors using nanomaterials can detect various gases even at low concentrations, installing such sensors in electronic healthcare devices is sought after, and research and development are being actively conducted.Semiconductor gas sensors detect gas through reduced electrical resistance due to gas molecules attached to the surface of crystalline semiconductor materials. For this, gas sensors need a specific surface area of nanomaterials. In order to use nanomaterials for conventional gas sensors, a complicated flow was necessary, from nanomaterials synthesis to cleansing, uniform dispersion of solvent, applying on substrates, and sintering. Thus, there is a concern that manufacturing technology of such gas sensors requires significant time and labor, increasing cost.A group of researchers led by Assistant Professor Tohru Sugahara (SUGANUMA Lab.) at The Institute of Scientific and Industrial Research, Osaka University, succeeded in producing nanostructured gas sensor devices for detecting volatile organic compounds (VOC) in breath for the purpose of healthcare in time equivalent to or shorter than one tenth of the time required for manufacturing conventional gas sensors. This group improved conventional complicated production methods, developing a simple production method of just sintering substrates applied with materials. This gas sensor's sensing response was comparable to the top-of-the-line sensors reported all over the world.Since demand in healthcare products is on the rise, there is a lot of activity in research and development of sensors for checking health and disease by examining the gas components of a person's breath. Breathalyzers for finding out who is driving drunk have already been commercialized. Recently, breath sensors for early detection of life-style diseases such as cancer and diabetes have been developed, but most of them are large, bulky and expensive. If gas sensors with high sensitivity are produced thanks to this group's research results, portable breath sensors enabling early detection of diseases will gain popularity.Reference:KGZ10 KGZ10-SPGMS10RVS