The Kynix Components - Sensors, Transducers
Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips
Product OverviewThe MP3V5004G series piezoresistive transducer is a state-of-the-art monolithic silicon pressure sensor designed for a wide range of applications, but particularly those employing a microcontroller or microprocessor with A/D inputs. This sensor combines a highly sensitive implanted strain gauge with advanced micromachining techniques, thin-film metallization, and bipolar processing to provide an accurate, high level analog output signal that is proportional to the applied pressure. This blog will introduce MP3V5004GC6U systematically from its features, pinout to its specifications, applications, also including MP3V5004GC6U datasheet and so much more. CatalogProduct OverviewMP3V5004GC6U FeaturesMP3V5004GC6U PinoutMinimum Recommended Footprint For Small Outline PackagesMP3V5004GC6U ApplicationsMP3V5004GC6U Operating CharacteristicsMP3V5004GC6U Maximum RatingsOn-chip Temperature Compensation and CalibrationPressure (p1)/Vacuum (p2) Side Identification TableMP3V5004GC6U PackageMP3V5004GC6U SpecificationMP3V5004GC6U ManufacturerMP3V5004GC6U DatasheetUsing WarningsMP3V5004GC6U FAQ MP3V5004GC6U FeaturesTemperature Compensated from 10°C to 60°CAvailable in Gauge Surface Mount (SMT) ConfigurationDurable Thermoplastic (PPS) Package MP3V5004GC6U PinoutThe following figure is the diagram of MP3V5004GC6U pinout. MP3V5004GC6U Pinout Minimum Recommended Footprint For Small Outline PackagesSurface mount board layout is a critical portion of the total design. The footprint for the semiconductor package must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. It is always recommended to fabricate boards with a solder mask layer to avoid bridging and/or shorting between solder pads, especially on tight tolerances and/or tight layouts. MP3V5004GC6U ApplicationsWashing Machine Water LevelIdeally Suited for Microprocessor or Microcontroller-Based Systems MP3V5004GC6U Operating CharacteristicsCharacteristicSymbolMinTypMaxUnitPressure RangePOP0—3.92400kPa mm H2OSupply Voltage(1)VS2.73.03.3VDCSupply CurrentIS——10mAdcSpan at 306 mm H2O (3 kPa)(2)VFSS—1.8—VOffset(3) (4)VOFF0.450.60.75VSensitivityV/P—0.65.9—V/kPa mV/mm H2OAccuracy(4) (5) 0 to 100 mm H2O (10 to 60°C)100 to 400 mm H2O (10 to 60°C)——————±1.5±2.5%VFSS%VFSS 1.Device is ratiometric within this specified excitation range.2.Span is defined as the algebraic difference between the output voltage at specified pressure and the output voltage at the minimum rated pressure.3.Offset (Voff) is defined as the output voltage at the minimum rated pressure.4.Accuracy (error budget) consists of the following:Linearity: Output deviation from a straight line relationship with pressure over the specified pressure range.Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is cycled to and from the minimum or maximum operating temperature points, with zero differential pressure applied.Pressure Hysteresis: Output deviation at any pressure within the specified range, when this pressure is cycled to and from the minimum or maximum rated pressure, at 25°C.Offset Stability: Output deviation, after 1000 temperature cycles, -30° to 100°C, and 1.5 million pressure cycles, with minimum rated pressure applied.TcSpan: Output deviation over the temperature range of 10° to 60°C, relative to 25°C.TcOffset: Output deviation with minimum rated pressure applied, over the temperature range of 10° to 60°C, relative to 25°C. Variation from Nominal: The variation from nominal values, for Offset or Full Scale Span, as a percent of VFSS, at 25°C.Auto-Zero at Factory Installation: Due to the sensitivity of the MP3V5004G, external mechanical stresses and mounting position can affect the zero pressure output reading. Auto-zeroing is defined as storing the zero pressure output reading and subtracting this from the device's output during normal operations. Reference AN1636 for specific information. The specified accuracy assumes a maximum temperature change of ±5°C between auto-zero and measurement. MP3V5004GC6U Maximum RatingsRatingSymbolValueUnitsMaximum Pressure (P1 > P2)PMAX16kPaStorage TemperatureTSTG–30 to +100°COperating TemperatureTA0 to +85°C Exposure beyond the specified limits may cause permanent damage or degradation to thedevice. Figure 1 shows a block diagram of the internal circuitry integrated on a pressure sensor chip. Figure 1. Fully Integrated Pressure Sensor Schematic On-chip Temperature Compensation and CalibrationThe performance over temperature is achieved by integrating the shear-stress strain gauge, temperature compensation, calibration and signal conditioning circuitry onto a single monolithic chip. Figure 2 illustrates the gauge configuration in the basic chip carrier (Case 482A). A fluorosilicone gel isolates the die surface and wire bonds from the environment, while allowing the pressure signal to be transmitted to the silicon diaphragm. The MP3V5004G series sensor operating characteristics are based on the use of dry air as pressure media. Media, other than dry air, may have adverse effects on sensor performance and long-term reliability. Internal reliability and qualification test for dry air, and other media, are available from the factory. Contact the factory for information regarding media tolerance in your application. Figure 3 shows the recommended decoupling circuit for interfacing the output of the MP3V5004G to the A/D input of the microprocessor or microcontroller. Proper decoupling ofthe power supply is recommended. Figure 4 shows the sensor output signal relative to pressure input. Typical, minimum and maximum output curves are shown for operation over a temperature range of 10°C to 60°C using the decoupling circuit shown in Figure 3 The output will saturate outside of the specified pressure range. Figure 2. Cross Sectional Diagram SSOP (not to scale) Figure 3. Recommended Power Supply Decoupling and Output Filtering. Figure 4. Output vs. Pressure Differential at ±2.5% VFSS Pressure (p1)/Vacuum (p2) Side Identification TableFreescale Semiconductor designates the two sides of the pressure sensor as the Pressure (P1) side and the Vacuum (P2) side. The Pressure (P1) side is the side containing silicone gel which isolates the die from the environment. The Freescale Semiconductor pressure sensor is designed to operate with positive differential pressure applied, P1 > P2. The Pressure (P1) side may be identified by using the table below. Part NumberCase TypePressure (P1) Side IdentifierMP3V5004GC6U/T1482ASide with Port AttachedMP3V5004GP1369Side with Port AttachedMP3V5004DP1351Side with Part MarkingMP3V5004GVP1368Stainless Steel Cap MP3V5004GC6U PackageThe following diagram shows the MP3V5004GC6U package. MP3V5004GC6U Package MP3V5004GC6U SpecificationProduct AttributeAttribute ValueManufacturer:NXPProduct Category:Board Mount Pressure SensorsPressure Type:GaugeOperating Pressure:0 Pa to 3.92 kPaOutput Type:AnalogMounting Style:SMD/SMTOperating Supply Voltage:2.7 V to 3.3 VPort Type:Single Axial BarblessPackage / Case:SOP-8Minimum Operating Temperature:0 CMaximum Operating Temperature:+ 85 CSeries:Series:MPXx5004Packaging:TubeOperating Supply Current: Operating Supply Current:10 mAPort Size:3.17 mmProduct Type:Pressure Sensors MP3V5004GC6U ManufacturerNXP Semiconductors enables secure connections and infrastructure for a smarter world, advancing solutions that make lives easier, better and safer. As the world leader in secure connectivity solutions for embedded applications, NXP is driving innovation in the secure connected vehicle, end-to-end security and privacy and smart connected solutions markets. MP3V5004GC6U DatasheetYou can download MP3V5004GC6U datasheet from the link given below:MP3V5004GC6U Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. MP3V5004GC6U FAQWhat type of sensor is the MP3V5004G series piezoresistive transducer? Monolithic silicon pressure sensor. What kind of analog output signal does the piezoresistive transducer provide?High level analog output signal. How does a pressure sensor work?Pressure transducers have a sensing element of constant area and respond to force applied to this area by fluid pressure. The force applied will deflect the diaphragm inside the pressure transducer. The deflection of the internal diaphragm is measured and converted into an electrical output. Where are pressure sensors used?Pressure sensors are used for control and monitoring in thousands of everyday applications. Pressure sensors can also be used to indirectly measure other variables such as fluid/gas flow, speed, water level, and altitude. What is an example of a pressure sensor?A common example of this is when a tire pressure gauge is used to measure the air pressure in an automobile tire.
Kynix On 2022-04-12
Product OverviewThe LM75A is a temperature-to-digital converter using an on-chip band gap temperature sensor and Sigma-delta A-to-D conversion technique. The device is also a thermal detector providing an overtemperature detection output. The LM75A contains a number of data registers: Configuration register (Conf) to store the device settings such as device operation mode, OS operation mode, OS polarity and OS fault queue as described in Section 7 “Functional description”; temperature register (Temp) to store the digital temp reading, and set-point registers (Tos and Thyst) to store programmable overtemperature shutdown and hysteresis limits, that can be communicated by a controller via the 2-wire serial I2C-bus interface. The device also includes an open-drain output (OS) which becomes active when the temperature exceeds the programmed limits. There are three selectable logic address pins so that eight devices can be connected on the same bus without address conflict. This blog will introduce LM75ADP systematically from its features, pinout to its specifications, applications, also including LM75ADP datasheet and so much more. CatalogProduct OverviewLM75ADP FeaturesLM75ADP PinoutLM75ADP ApplicationsLM75ADP Circuit DiagramLM75ADP Block DiagramLM75ADP PackageLM75ADP SpecificationLM75ADP ManufacturerLM75ADP DatasheetUsing WarningsLM75ADP FAQ LM75ADP Features■ Pin-for-pin replacement for industry standard LM75 and offers improved temperature resolution of 0.125 °C and specification of a single part over power supply range from 2.8 V to 5.5 V■ Small 8-pin package types: SO8 and TSSOP8■ I2C-bus interface with up to 8 devices on the same bus■ Power supply range from 2.8 V to 5.5 V■ Temperatures range from −55 °C to +125 °C■ 11-bit ADC that offers a temperature resolution of 0.125 °C■Temperature accuracy of:◆+2 °C from- 25°C to +100 °C◆+3°Cfrom-55°Cto+125°C■Programmable temperature threshold and hysteresis set points■Supply current of 3.5 μA in shutdown mode for power conservation■Stand- alone operation as thermostat at power-up ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101■Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA LM75ADP PinoutThe following figure is the diagram of LM75ADP pinout. LM75ADP Pinout LM75ADP Applications■ System thermal management■ Personal computers■ Electronics equipment■ Industrial controllers LM75ADP Circuit DiagramThe following is the circuit diagram of LM75ADP. LM75ADP Circuit Diagram LM75ADP Block DiagramThe following figure shows the block diagram of LM75ADP. LM75ADP Block Diagram LM75ADP PackageThe following diagram shows the LM75ADP package. LM75ADP Package LM75ADP SpecificationProduct AttributeAttribute ValueManufacturer:NXPProduct Category:Board Mount Temperature SensorsOutput Type:DigitalConfiguration:LocalAccuracy:+/- 3 CSupply Voltage - Min:2.8 VSupply Voltage - Max:5.5 VInterface Type:I2CResolution:11 bitMinimum Operating Temperature:- 55 CMaximum Operating Temperature:+ 125 CShutdown:ShutdownMounting Style:SMD/SMTPackage / Case:TSSOP-8Brand:NXP SemiconductorsOperating Supply Current:100 uAOutput Current:10 mAProduct:Product:Temperature Sensors with Thermal WatchdogsProduct Type:Temperature SensorsSeries:LM75A LM75ADP ManufacturerNXP Semiconductors enables secure connections and infrastructure for a smarter world, advancing solutions that make lives easier, better and safer. As the world leader in secure connectivity solutions for embedded applications, NXP is driving innovation in the secure connected vehicle, end-to-end security and privacy and smart connected solutions markets. LM75ADP DatasheetYou can download LM75ADP datasheet from the link given below:LM75ADP Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. LM75ADP FAQWhat technique does the LM75A use? Sigma-delta A-to-D conversion. What is the LM75A? Thermal detector. What is the name of the data register in the LM75A? Configuration register. What is a temperature sensor?A temperature sensor is a device that detects and measures hotness and coolness and converts it into an electrical signal. How does temperature sensor work?The basic principle of working of the temperature sensors is the voltage across the diode terminals. If the voltage increases, the temperature also rises, followed by a voltage drop between the transistor terminals of base and emitter in a diode.
Kynix On 2022-04-07
Product OverviewThe LSM6DSO is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope boosting performance at 0.55 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer. This blog will introduce LSM6DSO systematically from its features, pinout to its specifications, applications, also including LSM6DSO datasheet and so much more. CatalogProduct OverviewRelated Video IntroductionLSM6DSO FeaturesLSM6DSO PinoutLSM6DSO ApplicationsLSM6DSO Block DiagramLSM6DSO Application hintsLSM6DSO PackageLSM6DSO SpecificationLSM6DSO ManufacturerLSM6DSO DatasheetUsing WarningsLSM6DSO FAQ Related Video Introduction Video: 360° Lid Detection using LSM6DSO LSM6DSO Video Description: Learn how to use ST's LSM6DSO iNEMO inertial measurement unit (IMU) in a 360° lid detection application. LSM6DSO FeaturesPower consumption: 0.55 mA in combo high-performance mode“Always-on" experience with low power consumption for both accelerometer andgyroscopeSmart FIFO up to 9 kbyteAndroid compliant±2/±4/±8/±16 g full scale±125/±250/±500/±1000/±2000 dps full scaleAnalog supply voltage: 1.71 V to 3.6 VIndependent IO supply (1.62 V)Compact footprint: 2.5 mm x 3 mm x 0.83 mmSPI / I²C & MIPI I3CSM serial interface with main processor data synchronizationAuxiliary SPI for OIS data output for gyroscope and accelerometerAdvanced pedometer, step detector and step counterSignificant Motion Detection, Tilt detectionStandard interrupts: free-fall, wakeup, 6D/4D orientation, click and double-clickProgrammable Finite State Machine: accelerometer, gyroscope and externalsensorsEmbedded temperature sensor LSM6DSO PinoutThe following figure is the diagram of LSM6DSO pinout. LSM6DSO Pinout LSM6DSO ApplicationsMotion tracking and gesture detectionSensor hubIndoor navigationIoT and connected devicesSmart power saving for handheld devicesEIS and OIS for camera applicationsVibration monitoring and compensation LSM6DSO Block DiagramThe following figure shows the block diagram of LSM6DSO. LSM6DSO Block Diagram LSM6DSO Application hintsThe following are the diagrams of LSM6DSO application hints. LSM6DSO electrical connections in Mode 1 LSM6DSO electrical connections in Mode 2 LSM6DSO electrical connections in Mode 3 and Mode 4 LSM6DSO PackageThe following diagram shows the LSM6DSO package. LSM6DSO Package LSM6DSO SpecificationManufacturer:STMicroelectronicsOperating Temperature-Max:85 °COperating Temperature-Min: -40 °CSupply Voltage-Max (Vsup):3.6 VSupply Voltage-Min (Vsup):1.71 VSupply Voltage-Nom (Vsup):1.8 VProduct Type: IMUs - Inertial Measurement UnitsSubcategory: Sensors LSM6DSO ManufacturerSTMicroelectronics is a global independent semiconductor company and a leader in developing and delivering semiconductor solutions across the spectrum of microelectronics applications. An unrivaled combination of silicon and system expertise, manufacturing strength, Intellectual Property (IP) portfolio, and strategic partners positions, STMicroelectronics is at the forefront of System-on-Chip(SoC) technology and its products play a key role in enabling today's convergence trends. LSM6DSO DatasheetYou can download LSM6DSO datasheet from the link given below:LSM6DSO Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. LSM6DSO FAQWhat is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope?LSM6DSO. What is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope?0.55 mA. What unit is IMU?An inertial measurement unit (IMU) is an electronic device that measures and reports a body's specific force, angular rate, and sometimes the orientation of the body, using a combination of accelerometers, gyroscopes, and sometimes magnetometers. What are IMU in phone?An IMU is a specific type of sensor that measures angular rate, force and sometimes magnetic field. IMUs are composed of a 3-axis accelerometer and a 3-axis gyroscope, which would be considered a 6-axis IMU. What is IMU bandwidth?The bandwidth is the maximum frequency to which a sensor or system will respond. This frequency is typically defined at the point where the response has dropped to half power, or the -3 dB point on a Bode mangitude plot.
Kynix On 2022-03-11
Product OverviewThe BNO055 is a System in Package (SiP), integrating a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second, a triaxial geomagnetic sensor and a 32-bit cortex M0+ microcontroller running Bosch Sensortec sensor fusion software, in a single package. The corresponding chip-sets are integrated into one single 28-pin LGA 3.8mm x 5.2mm x 1.1 mm housing. For optimum system integration the BNO055 is equipped with digital bidirectional I2C and UART interfaces. The I2C interface can be programmed to run with the HID-I2C protocol turning the BNO055 into a plug-and-play sensor hub solution for devices running the Windows 8.0 or 8.1 operating system. This blog will introduce BNO055 systematically from its features, pinout to its specifications, applications, also including BNO055 datasheet and so much more. CatalogProduct OverviewRelated Video IntroductionBNO055 FeaturesBNO055 ComponentsSolution provided functionalityWhat makes the difference?BNO055 PinoutBNO055 ApplicationsBNO055 Connection DiagramsBNO055 PackageBNO055 SpecificationBNO055 ManufacturerBNO055 DatasheetUsing WarningsBNO055 FAQ Related Video Introduction Video: Setting up the BNO055 Absolute Orientation Sensor | Automatic Addison BNO055 Video Description: In this video, we'll set up the Adafruit BNO055 Absolute Orientation Sensor from scratch, step-by-step. The BNO055 is actually three sensors in one device. It includes an accelerometer to measure acceleration forces, a gyroscope that uses Earth's gravity to help determine orientation, and a magnetometer that measures magnetism. BNO055 FeaturesIncludes all sensors, sensor hub and optimized softwareLow power consumption, supports various power modes for switching sensors on and off and algorithm modules to speed code developmentAdvanced 9-axis sensor fusion algorithms Fast background calibration of all sensors and calibration monitor while in useEnhanced magnetic distortion detection and suppressionReal-time motion tracking due to built-in group delay compensationGyroscope drift cancellationSupports multiple operating mode, i.e. 6-axis based applications (inertial measurement Units) BNO055 Components3-axis accelerometer (14Bit)3-axis gyroscope (16Bit)3-axis geomagnetic sensor32 bit ARM Microcontroller2 x 3.8 mm² footprintBosch Sensortec Sensor Data Fusion with fast magnetic calibration (optimally integrated & tuned) Solution provided functionalityWindows 8.1 compatibleHigh accuracy quaternion: 2-3 deg (static)Low latency: 20 msLow calibration time: 2-3 sImmune to magnetic distortionsPower consumption advantages through integration What makes the difference?Hardware and software co-design enables high performance with low power consumptionQuaternion communication is 10x more efficient than raw dataIntegrated sensor fusion software reduces customer development costs and timeAll components in one package leads to simplified system integration and faster time to marketFootprint is significantly reduced compared to discrete and system on board solutions BNO055 PinoutThe following figure is the diagram of BNO055 pinout. BNO055 Pinout BNO055 ApplicationsNavigationRoboticsFitness and well-beingAugmented realityContext awarenessTablets and ultra-books BNO055 Connection DiagramsThe connection diagrams of BNO055 are shown in the picture below. I2C connection diagram UART connection diagram HID via IC connection diagram BNO055 PackageThe following diagram shows the BNO055 package. BNO055 Package BNO055 SpecificationProduct AttributeAttribute ValueManufacturer:BoschProduct Category:IMUs - Inertial Measurement UnitsSensor Type:9-axisSensing Axis:X, Y, ZSensitivity:1 LSB/mgAcceleration:2 g, 4 g, 8 g, 16 gOutput Type:DigitalInterface Type:HID-I2C, I2C, UARTResolution:16 bitOperating Supply Current:13.7 mASupply Voltage - Min:2.4 VSupply Voltage - Max:3.6 VMinimum Operating Temperature:- 40 CMaximum Operating Temperature:+ 85 CPackage / Case:LGA-28Packaging:Packaging:ReelBandwidth:1000 Hz BNO055 ManufacturerThe Bosch Group, a leading global supplier of technology and services, is designed to improve quality of life worldwide with products and services that are innovative and spark enthusiasm. BNO055 DatasheetYou can download BNO055 datasheet from the link given below:BNO055 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. BNO055 FAQWhat is in an IMU?Inertial measurement unit (IMU) The IMU is a sensor that measures triaxial acceleration and triaxial angular velocity. The IMU consists of an accelerometer, which can output linear acceleration signals on three axes in space, and a gyroscope, which can output angular velocity signals on three axes in space. What three components are in an IMU?An IMU is a specific type of sensor that measures angular rate, force and sometimes magnetic field. IMUs are composed of a 3-axis accelerometer and a 3-axis gyroscope, which would be considered a 6-axis IMU. They can also include an additional 3-axis magnetometer, which would be considered a 9-axis IMU. How does inertial measurement unit work?An inertial measurement unit works by detecting linear acceleration using one or more accelerometers and rotational rate using one or more gyroscopes. Typical configurations contain one accelerometer, gyro, and magnetometer per axis for each of the three principal axes: pitch, roll and yaw. What is the BNO055 equipped with for optimum system integration? Digital bidirectional I2C and UART interfaces. What can the I2C interface be programmed to run with?HID-I2C protocol.
Kynix On 2022-02-23
Product OverviewThe MPU-60X0 is the world’s first integrated 6-axis MotionTracking device that combines a 3-axis gyroscope, 3-axis accelerometer, and a Digital Motion Processor™ (DMP) all in a small 4x4x0.9mm package. With its dedicated I2C sensor bus, it directly accepts inputs from an external 3-axis compass to provide a complete 9-axis MotionFusion™ output. The MPU-60X0 MotionTracking device, with its 6-axis integration, on-board MotionFusion™, and run-time calibration firmware, enables manufacturers to eliminate the costly and complex selection, qualification, and system level integration of discrete devices, guaranteeing optimal motion performance for consumers. The MPU-60X0 is also designed to interface with multiple noninertial digital sensors, such as pressure sensors, on its auxiliary I2C port. The MPU-60X0 is footprint compatible with the MPU-30X0 family. The MPU-6000 and MPU-6050 are identical, except that the MPU-6050 supports the I2C serial interface only, and has a separate VLOGIC reference pin. The MPU-6000 supports both I2C and SPI interfaces and has a single supply pin, VDD, which is both the device’s logic reference supply and the analog supply for the part. This blog will introduce MPU-6050 systematically from its features, pinout to its specifications, applications, also including MPU-6050 datasheet and so much more. CatalogProduct OverviewRelated Video IntroductionMPU-6050 FeaturesMPU-6050 PinoutMPU-6050 ApplicationsMPU-6050 CAD ModelsMPU-6050 Circuit DiagramMPU-6050 Block DiagramMPU-6050 PackageMPU-6050 SpecificationMPU-6050 ManufacturerMPU-6050 DatasheetUsing WarningsMPU-6050 FAQ Related Video Introduction Video: Build an Electronic Level with MPU-6050 and Arduino MPU-6050 Video Description: Today we will be working with the MPU-6050, a low-cost Inertial Measurement Unit, or IMU. This device has a lot of different applications in many fields including robotics, gaming, quadcopters, and IoT devices. The MPU-6050 has an internal gyroscope and accelerometer. It's an inexpensive device, available in several packages and modules. The module I am using is very common and has a built-0in voltage regulator so it can work with 5-volt logic. We will start by looking at the MPU-6050 internals, as well as at the pinout of the module I am using. Next, we will load a couple of libraries into our Arduino IDE and ruins some sample code to display Pitch, Yaw, and Roll. After that, we will build a small project, an electronic level. Our level will display on an LCD and will also use 5 LEDs to give a good visual indication of how level the surface is. MPU-6050 FeaturesDigital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-programmable fullscale range of ±250, ±500, ±1000, and ±2000°/secExternal sync signal connected to the FSYNC pin supports image, video and GPS synchronizationIntegrated 16-bit ADCs enable simultaneous sampling of gyrosEnhanced bias and sensitivity temperature stability reduces the need for user calibrationImproved low-frequency noise performanceDigitally-programmable low-pass filterGyroscope operating current: 3.6mAStandby current: 5µAFactory calibrated sensitivity scale factorUser self-test MPU-6050 PinoutThe following figure is the diagram of MPU-6050 pinout. MPU-6050 Pinout MPU-6050 ApplicationsBlurFree™ technology (for Video/Still Image Stabilization)AirSign™ technology (for Security/Authentication)TouchAnywhere™ technology (for “no touch” UI Application Control/Navigation)MotionCommand™ technology (for Gesture Short-cuts)Motion-enabled game and application frameworkInstantGesture™ iG™ gesture recognitionLocation based services, points of interest, and dead reckoningHandset and portable gamingMotion-based game controllers3D remote controls for Internet connected DTVs and set top boxes, 3D miceWearable sensors for health, fitness and sportsToys MPU-6050 CAD ModelsThe following are MPU-6050 Symbol, Footprint, and 3D Model. MPU-6050 Symbol MPU-6050 Footprint MPU-6050 3D Model MPU-6050 Circuit DiagramThe following is the circuit diagram of MPU-6050. MPU-6050 Typical Operating Circuit MPU-6050 Block DiagramThe following figure shows the block diagram of MPU-6050. MPU-6050 Block Diagram MPU-6050 PackageThe following diagram shows the MPU-6050 package. MPU-6050 Package MPU-6050 SpecificationProduct AttributeAttribute ValueManufacturer:TDKProduct Category:IMUs - Inertial Measurement UnitsSensor Type:6-axisSensing Axis:X, Y, ZSensitivity:340 LSB/CAcceleration:10000 gOutput Type:DigitalInterface Type:I2COperating Supply Current:3.9 mASupply Voltage - Min:2.375 VSupply Voltage - Max:3.46 VMinimum Operating Temperature:- 40 CMaximum Operating Temperature:+ 105 CMoisture Sensitive:YesSubcategory:Sensors MPU-6050 ManufacturerInvenSense, Inc, a TDK Group Company: InvenSense is part of the Sensor System Business Company within TDK and is the industry leader in MEMS Motion, Audio, and Pressure Solutions for the consumer, industrial, automotive, and IoT market segments. With a very robust portfolio of MEMS 3/6/7/9 axis motion sensors, accompanied by the highest performing MEMS audio microphones, and pressure sensors - TDK continues to push the boundaries of performance and quality; setting new standards of innovation across multiple industries. MPU-6050 DatasheetYou can download MPU-6050 datasheet from the link given below:MPU-6050 Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. MPU-6050 FAQWhat is the MPU-60X0 compatible with? Footprint compatible with the MPU-30X0 family. What is the MPU-60X0 designed to interface with on its auxiliary I 2C port?Pressure sensors. What is the main supply pin for the MPU-6000?VDD. What are the units of inertial measurement?An Inertial Measurement Unit (IMU) is a device that can measure and report specific gravity and angular rate of an object to which it is attached. An IMU typically consists of: Gyroscopes: providing a measure angular rate. Accelerometers: providing a measure specific force/acceleration. What can IMUs measure?As you've seen, IMUs are used to measure acceleration, angular velocity and magnetic fields, and, when combined with sensor fusion software, they can be used to determine motion, orientation and heading. They're found in many applications across consumer electronics and the industrial sector.
Kynix On 2022-01-25
Product OverviewThe LSM6DSL is a system-in-package featuring a 3D digital accelerometer and a 3D digital gyroscope performing at 0.65 mA in high-performance mode and enabling always-on low-power features for an optimal motion experience for the consumer. The LSM6DSL supports main OS requirements, offering real, virtual and batch sensors with 4 kbyte for dynamic data batching. This blog will introduce LSM6DSL systematically from its features, pinout to its specifications, applications, also including LSM6DSL datasheet and so much more. CatalogProduct OverviewLSM6DSL FeaturesLSM6DSL PinoutLSM6DSL ApplicationsLSM6DSL CAD ModelsLSM6DSL Block DiagramLSM6DSL Circuit DiagramLSM6DSL PackageLSM6DSL SpecificationLSM6DSL ManufacturerLSM6DSL DatasheetUsing WarningsLSM6DSL FAQ LSM6DSL FeaturesPower consumption: 0.4 mA in combo normal mode and 0.65 mA in combo high-performancemode“Always-on” experience with low power consumption for both accelerometer and gyroscopeSmart FIFO up to 4 kbyte based on features setCompliant with Android K, L, and MHard, soft ironing for external magnetic sensor corrections±2/±4/±8/±16 g full scale±125/±245/±500/±1000/±2000 dps full scaleAnalog supply voltage: 1.71 V to 3.6 VIndependent IOs supply (1.62 V)Compact footprint, 2.5 mm x 3 mm x 0.83 mmSPI & I2C serial interface with main processor data synchronization featurePedometer, step detector and step counterSignificant motion and tilt functionStandard interrupts: free-fall, wakeup, 6D/4D orientation, click and double-clickEmbedded temperature sensorECOPACK®, RoHS and“Green” compliant LSM6DSL PinoutThe following figure is the diagram of LSM6DSL pinout. LSM6DSL Pinout LSM6DSL ApplicationsMotion tracking and gesture detectionCollecting sensor dataIndoor navigationIoT and connected devicesIntelligent power saving for handheld devicesVibration monitoring and compensation LSM6DSL CAD ModelsThe following are LSM6DSL Symbol and Footprint. LSM6DSL Symbol LSM6DSL Footprint LSM6DSL Block DiagramThe following figure shows the block diagram of LSM6DSL. LSM6DSL Block Diagram LSM6DSL Circuit DiagramThe device core is supplied through the Vdd line. Power supply decoupling capacitors (C1, C2 = 100 nF ceramic) should be placed as near as possible to the supply pin of the device (common design practice).The functionality of the device and the measured acceleration/angular rate data is selectable and accessible through the SPI/I2C interface.The functions, the threshold and the timing of the two interrupt pins for each sensor can be completely programmed by the user through the SPI/I2C interface. LSM6DSL electrical connections in Mode 1 LSM6DSL electrical connections in Mode 2 LSM6DSL PackageThe following diagram shows the LSM6DSL package. LSM6DSL Package LSM6DSL SpecificationEU RoHSCompliant with ExemptionECCN (US)EAR99Part StatusPreliminaryAutomotiveNoPPAPNoProduct CategoryAccelerometer and GyroscopeMinimum Operating Temperature (°C)-40Maximum Operating Temperature (°C)85PackagingTrayMinimum Storage Temperature (°C)-40Maximum Operating Supply Voltage (V)3.6Typical Operating Supply Voltage (V)1.8Supplier PackageLGAPin Count14MountingSurface MountPackage Height0.86Package Length3Package Width2.5PCB changed14Lead ShapeNo Lead LSM6DSL ManufacturerST is a global semiconductor leader delivering intelligent and energy-efficient products and solutions that power the electronics at the heart of everyday life. ST’s products are found everywhere today, and together with our customers, we are enabling smarter driving and smarter factories, cities and homes, along with the next generation of mobile and Internet of Things devices. By getting more from technology to get more from life, ST stands for life.augmented. LSM6DSL DatasheetYou can download LSM6DSL datasheet from the link given below:LSM6DSL Datasheet Using WarningsNote: Please check their parameters and pin configuration before replacing them in your circuit. LSM6DSL FAQHow many kbytes of data is the LSM6DSL? 4 kbyte. What is the power consumption of LSM6DSL?0.4 mA. What is LSM6DSL used for?LSM6DSL can be used for motion tracking and gesture detection, collecting sensor data, indoor navigation, iot and connected devices, intelligent power saving for handheld devices and vibration monitoring and compensation. What is iNEMO?iNEMO™ inertial modules are inertial measurement units (IMU) which integrate complementary types of sensors to offer more compact, robust, and easy-to-assemble solutions compared to discrete MEMS products. What does an IMU output?An inertial measurement unit (IMU) measures and reports raw or filtered angular rate and specific force/acceleration experience by the object it is attached to. Data outputs for an IMU are typically body-frame accelerations, angular rates and (optionally) magnetic field measurements.
Kynix On 2022-01-21
Join our mailing list!
Be the first to know about new products, special offers, and more.
Feature Posts
ENC624J600-I/PT microcontroller: Datasheet, Features, Application[FAQ]2023-03-07
ATMEGA1280-16AU microcontroller: Datasheet, Features, Application[FAQ]2023-03-07
STM8S207CBT6 Microcontroller: Datasheet, Features, Application[FAQ]2023-03-06
2N7002P Mosfet: Datasheet, Pinout, Features [FAQ]2021-10-21
L298N Motor Driver: Datasheet, Arduino, Circuit [Video&FAQ]2021-10-21














