thyristors Related Articles

ⅠIntroductionThyristors are high-speed solid-state devices that can control motors, heaters, and lighting. Before we get into Thyristor Circuits. We'll look at the basic construction and operation of the Silicon Controlled Rectifier, also known as a Thyristor. Next, we'll look at how we can use thyristors and thyristor switching circuits to control much larger loads like lamps, motors, or heaters, among other things. CatalogⅠIntroductionⅡ Thyristors Circuits Related VideoⅢ What Is Silicon Controlled Rectifier?Ⅳ Construction of Silicon Controlled RectifierⅤ What is a Thyristor?Ⅵ Thyristor Switching Circuits6.1 Thyristor Circuit in DC6.2 AC Thyristor CircuitⅦ How an SCR Circuit Works with Thyristor Circuits?7.1 DC Thyristor / SCR Circuit7.2 Basic AC Thyristor / SCR Circuit7.3 AC SCR Circuit with Gate Phase ControlⅧ FAQ Ⅱ Thyristors Circuits Related VideoSilicon Control Rectifier SCR Basic AC Circuit Thyristors Circuits Video Description:  Silicon Control Rectifier SCR Basic AC Circuit Ⅲ What Is Silicon Controlled Rectifier?The Silicon Controlled Rectifier (SCR) is one of the most popular devices in the market. SCR can be found in a variety of applications such as rectification, power regulation, and inversion, among others. SCR, like a diode, is a unidirectional device that allows current in one direction but opposes it in the other gate. SCRs have the ability to turn ON or OFF, and their switching is controlled by biasing conditions and the gate input terminal.By varying the ON periods of the SCR, the average power delivered at the load can be varied. It is capable of handling tens of thousands of voltages and currents. Figure depicts the SCR symbol and its terminals.Figure1 :Silicon Controlled Rectifier   Ⅳ Construction of Silicon Controlled RectifierAs shown in the figure, an SCR has three terminals: anode, cathode, and gate. SCRs have the ability to turn ON or OFF, and their switching is controlled by biasing conditions and the gate input terminal.By varying the ON periods of the SCR, the average power delivered at the load can be varied. It is capable of handling tens of thousands of voltages and currents. Figure depicts the SCR symbol and its terminals.Figure2:Construction The SCR is manufactured using three different types of constructions: planar, Mesa, and press pack. Planar construction, in which all junctions in an SCR are diffused, is used for low-power SCRs. In a mesa type construction, junction J2 is formed by diffusion and the outer layers are alloyed to it as a result. This design is primarily used in high-power Silicon Controlled Rectifiers. The SCR is braced with plates made of molybdenum or tungsten to provide high mechanical strength. One of these plates is soldered to a copper stud, which is threaded to connect to the heat sink. Ⅴ What is a Thyristor?A thyristor is a four-layer solid-state semiconductor device made of P and N materials. When a gate receives a triggering current, it begins to conduct until the voltage across the thyristor device is biased forward. In this case, it functions as a bistable switch. To control a large amount of current flowing through the two leads, we must create a three-lead thyristor by combining the small amount of current with that current. This is referred to as control lead. If the potential difference between the two leads is less than the breakdown voltage, a two-lead thyristor is used to turn the device on.Figure3:Thyristor Ⅵ Thyristor Switching CircuitsDC Thyristor CircuitAC Thyristor circuit 6.1 Thyristor Circuit in DCWhen connected to a DC supply, we use a thyristor to control larger DC loads and current. The main advantage of using a thyristor in a DC circuit as a switch is that it provides a high current gain. Because a small gate current can control a large anode current, the thyristor is classified as a current-operated device.Figure4:Thyristor Circuit in DC 6.2 AC Thyristor CircuitWhen connected to an alternating current supply, the thyristor behaves differently because it is not the same as a DC-connected circuit. A thyristor is used as an AC circuit during one half of a cycle, causing it to turn off automatically due to its reverse biased condition. Figure6:AC Thyristor Circuit Ⅶ How an SCR Circuit Works with Thyristor Circuits?7.1 DC Thyristor / SCR CircuitMany applications call for an SCR circuit to control the operation of a DC load. This can be used for switching DC motors, lamps, or any other load.The basic SCR circuit shown below can control power to a load by using a small switch to initiate power application to the load.Figure7:Basic DC thyristor / SCR circuit With S1 closed and S2 open, no current will flow at first. The SCR circuit will turn on and the current will flow in the load only when S2 is closed and it triggers the gate by causing the gate current to flow.Until the anode circuit is broken, the current will continue to flow. S1 can be used for this. Another method is to place the switch S1 across the SCR and briefly close it, causing the voltage across the SCR to disappear and the SCR to stop conducting.Because of their functions in this SCR circuit, S1 and S2 may be referred to as the Off switch and the ON switch, respectively. In this configuration, S1 must be able to carry the full load current, while S2 must only carry the gate current. Once the SCR is turned on, the switch can be released and remain open because the SCR's action maintains the current flow through the device and thus the load.R1 connects the gate to the power supply via the switch. When S2 is closed, current flows through the resistor enters the gate and activates the SCR. The resistor R1 must be calculated to provide enough gate current to turn on the SCR circuit.R2 is included to reduce the SCR's sensitivity so that it does not fire on any noise that is detected. 7.2 Basic AC Thyristor / SCR CircuitWhen using a thyristor circuit with AC, a few changes must be made, as shown below.This is because alternating current reverses polarity throughout the cycle. This means that the SCR will become reverse-biased, effectively lowering the anode voltage to zero and causing it to turn OFF for one-half of each cycle. As a result, there is no need for an off switch because this is accomplished as part of the use of an alternating current supply.When using a thyristor circuit with AC, a few changes must be made, as shown below.This is because alternating current reverses polarity throughout the cycle. This means that the SCR will become reverse-biased, effectively lowering the anode voltage to zero and causing it to turn OFF for one-half of each cycle. As a result, there is no need for an off switch because this is accomplished as part of the use of an alternating current supply.Figure8: AC thyristor / SCR circuitThe circuit operates in a slightly different manner than the DC SCR circuit. When the switch is turned on, the circuit must wait for sufficient anode voltage to be available as the AC waveform progresses along its path. In addition, the SCR circuit will have to wait until the voltage within the gate section of the circuit is high enough to trigger the SCR. The switch must be in a closed position for this to work.Once triggered, the SCR will remain to conduct for the duration of the positive half of the cycle. As the voltage falls, the anode-cathode voltage will become insufficient to support conduction. At this point, the SCR will come to a halt.The SCR will then not operate during the negative half of the cycle. The process will only be repeated when the next positive half of the cycle returns. As a result, this circuit will only operate when the gate switch is closed.One disadvantage of using this type of SCR circuit is that it cannot supply more than 50% power to the load because it does not conduct during the negative half of the AC cycle because the SCR is reverse biased. 7.3 AC SCR Circuit with Gate Phase ControlBy varying the proportion of the half-cycle over which the SCR conducts, the amount of power reaching the load can be controlled. This can be accomplished by using an SCR circuit with phase control of the input gate signal.Figure9:AC thyristor circuit waveformsThe SCR gate signal is derived from an RC circuit consisting of R1, VR1, and C1 before the diode D1 when using the SCR circuit with phase control.Because the SCR is forward biased, only the positive half cycle of the waveform is of interest, as with the basic AC SCR circuit. During this half-cycle, the capacitor, C1, charges up from the AC supply voltage via the resistor network of R1 and VR1. The waveform at the positive end of C1 is seen to lag behind the input waveform, and the Gate is only triggered when the voltage at the capacitor's high end has risen sufficiently to trigger the SCR via D1. As a result, the SCR's turn-on time is delayed compared to what it would be if the RC network was not present. The VR1 value changes the delay and thus the proportion of the cycle over which the SCR operates. The power into the load can thus be adjusted in this manner. Figure10: AC thyristor circuit with gate phase control R1 is a series resistor that has been included to limit the minimum value for the resistor network to a value that will provide an acceptable gate current level for the SCR. The phase angle of the gate waveform must typically vary between 0° and 180° to provide complete control of the 50% of the cycle available for conduction with an SCR. These circuits demonstrate some of the fundamental concepts underlying the design of SCR thyristor circuits. They show how they work and how they can be used in their most basic form. One of the most important considerations when designing thyristor circuits is power dissipation. Because these circuits frequently handle high voltages and high power levels, power dissipation can be a significant factor in circuit design and operation. Ⅷ FAQ1. What does a thyristor do in a circuit?The primary function of a thyristor is to control electric power and current by acting as a switch. For such a small and lightweight component, it offers adequate protection to circuits with large voltages and currents (up to 6000 V, 4500 A).2. How thyristor acts as a switch?When connected to a direct current DC supply, the thyristor can be used as a DC switch to control larger DC currents and loads. When using the Thyristor as a switch it behaves like an electronic latch because once activated it remains in the “ON” state until manually reset3. What is difference between SCR and thyristor?Thyristor is a four semiconductor layer or three PN junction device. It is also known as “SCR” (Silicon Control Rectifier). The term “Thyristor” is derived from the words of thyratron (a gas fluid tube which works as SCR) and Transistor. Thyristors are also known as PN PN Devices.4. Is thyristor convert AC to DC?A single-phase thyristor rectifier converts an AC voltage to a DC voltage at the output. The power flow is bidirectional between the AC and the DC side.5. What are the advantages of thyristor?Advantages of Thyristor :It is easy to turn on. It is able to control AC power. It can switch high voltage, a high current device. It cost is very low. 

IntroductionThyristor is a four semiconductor layers or three PN junctions devicea solid-state semiconductor device with four layers of alternating P- and N-type materials. It is also known as “SCR” (Silicon Control Rectifier). The term “Thyristor” is dervid from the words of thyratron (a gas fluid tube which work as SCR) and Transistor. And It acts exclusively as a bistable switch in electronic circuit.What is a Thyristor?CatalogIntroductionⅠ Types of ThyristorsⅡ Thyristor Selection2.1 Specific Requirements of Applying Circuit2.2 Main Parameters of the ThyristorⅢ Replacement of ThyristorⅣ Detection of Thyristor4.1 Detection of Unidirectional Thyristors4.2 Detection of TRIACⅠ Types of ThyristorsCommonly used thyristors include unidirectional thyristors, TRIAC, and turn-off thyristors, etc., which should be selected reasonably according to the needs of the circuit.— Unidirectional ThyristorThe unidirectional thyristor is characterized in that the current can only flow from the anode A to the cathode k, and is mainly used in the control of DC power supply or pulsating direct current, AC power rectification, and DC power inverter.Unidirectional thyristors can be divided into ordinary thyristors and high-frequency thyristors (the working frequency is above 110kHz). Commonly used unidirectional thyristors are 3CT series, 3DT series, KP series and KK series (high frequency thyristors), and imported MCR series, SF series, BST series etc.— TRIACTRIAC was developed on the basis of the unidirectional thyristor and is an AC power control device. TRIAC can not only replace two unidirectional thyristors in anti-parallel, but also requires only one trigger circuit, which is more convenient to use.The characteristic of TRIAC is that alternating current can pass through it, which is mainly used in the control of AC power supply and the adjustment of AC voltage. Commonly used TRIAC include 3CTS series and KS series, as well as imported MAC series, SM series, BCR series, etc.— Gate Turn-off ThyristorThe characteristic of the gate turn-off thyristor is that it can be switched off by the control electrode. It is mainly used in gate turn-off contactless switches, DC inverters, dimmer, speed regulation and other occasions.Gate turn-off thyristors are power-type control devices developed on the basis of ordinary thyristors. After the ordinary thyristor is triggered to be turned on, its control electrode does not work. To turn off the thyristor, the power must be cut off, or the forward current flowing through the thyristor must be less than the holding current. Gate turn-off thyristor overcomes the above drawbacks. When the control electrode G is added with a positive pulse voltage, the thyristor is turned on, and when the control electrode G is added with a negative pulse voltage, the thyristor is turned off.Gate turn-off thyristors are ideal high-voltage, high-current switching devices. For example, the DG series high-power gate turn-off thyristors can reach a maximum voltage of 4500V and a maximum current of 3000A. Ⅱ Thyristor Selection2.1 Specific Requirements of Applying CircuitThere are many types of thyristors, which should be selected reasonably according to the specific requirements of the application circuit.For AC/DC voltage control, controllable rectification, AC voltage regulation, power inverter, switching power supply protection circuit, etc., ordinary thyristors can be selected.For AC switch, AC voltage regulation, AC motor linear speed regulation, lamp linear dimming, solid state relay, solid state contactor, etc., a TRIAC should be selected.For AC motor variable frequency speed regulation, chopper, power inverter and various electronic switch circuits, you can choose gate turn-off thyristor.For sawtooth wave generator, long time delay, over voltage protector and trigger circuit with power transistor, etc., BTG thyristor can be selected.In electromagnetic cookers, electronic ballasts, ultrasonic circuits, superconducting magnetic energy storage systems, switching power supplies and other circuits, reverse conducting thyristors can be selected.In the photocoupler, light detector, light alarm, light counter, photoelectric logic circuit and operation monitoring circuit of automatic production line, the light-control thyristor can be selected.2.2 Main Parameters of the ThyristorThe main parameters of the thyristor should be determined according to the specific requirements of the application circuit.The selected thyristor should have a certain power margin, and its rated peak voltage and rated current (on-state average current) should be higher than the maximum operating voltage and maximum working current of the controlled circuit by 1.5 to 2 times.The parameters of the thyristor's forward voltage drop, gate trigger current, and trigger voltage should meet the requirements of the application circuit (this refers to the control circuit of the gate), and should not be high or low, otherwise it will affect the normal operation of the thyristor. Ⅲ Replacement of ThyristorAfter the thyristor is damaged, if no thyristor of the same type is replaced, another type of thyristor with similar performance parameters can be used instead.When designing an application circuit, a large margin is generally left. When replacing the thyristor, just pay attention to its rated peak voltage (repeated peak voltage), rated current (on-state average current), gate trigger voltage and gate trigger current, especially the two indicators of rated peak voltage and rated current.The switching speed of the thyristor used for replacement should be consistent with the switching speed of the damaged thyristor. For example: After the high-speed thyristor used in the pulse circuit and high-speed inverter circuit is damaged, only the same type of fast thyristor can be used instead of the ordinary thyristor.When selecting a thyristor to be used for replacement, it is not necessary to leave too much margin for any parameter, and the parameter of it should be as close as possible to the parameter of the replaced thyristor, because an excessively large margin is not only a waste, but also sometimes has side effects, such as non-triggering or insensitive triggering.In addition, the appearance of the two thyristors should be the same, otherwise it will cause inconvenience to the installation. Ⅳ Detection of ThyristorThyristors are usually represented by the letters "SCR" in circuit schematic diagrams. For example, SCR2 refers to the thyristor numbered 2. The symbol of the thyristor in the schematic diagram is shown in figure 1. Figure 1. Symbols of Thyristor4.1 Detection of Unidirectional Thyristors(1) Discrimination of each electrode: According to the structure of an ordinary thyristor, it can be seen that there is a PN junction between the gate G and the cathode K, which has unidirectional conductive characteristics, while there are two PN junctions of opposite polarities connected in series between the anode A and the gate. Therefore, by measuring the resistance between the pins of an ordinary thyristor with the R × 100 or R × 1 k Q level of the multimeter, three electrodes can be determined.The specific method is: use the black probe of the multimeter to connect one electrode of the thyristor, and use the red probe to touch the other two electrodes in turn. If the measurement result has a resistance value of several thousand ohms (kΩ) and another resistance value of several hundred ohms(Ω), it can be determined that the black probe is connected to gate G. In the measurement with a resistance value of several hundred ohms, the red probe was connected to the cathode K, and in the measurement with a resistance value of several thousand ohms, the red probe was connected to the anode A. If the measured resistance values are both very large, it means that the black probe is not connected to gate G. Apply the same method to test other electrodes until three electrodes are found.You can also measure the forward and reverse resistance between any two pins. If the forward and reverse resistance are close to infinity, the two electrodes are anode A and cathode K, and the other pin is gate G.Each electrode of the ordinary thyristors can also be judged according to its packaging form.For example, the bolt end of the bolt-type ordinary thyristor is anode A, the thinner lead end is gate G, and the thicker lead end is cathode K.The lead end of the flat thyristor is gate G, the flat end is anode A, and the other end is cathode K.A thyristor of metal package (T0-3) is a common thyristor and its shell is anode A.The middle pin of the plastic thyristor (T0-220) is anode A, and it is mostly connected with its own heat sink. Figure 2. Pin Arrangement of Several Common Thyristors(2) Judging whether it is good or bad: Use the R×1 kΩ level of a multimeter to measure the forward and reverse resistance values between anode A and cathode K of ordinary thyristor, which should normally be infinite (∞) ; If the forward and reverse resistance values are zero or the resistance values are both small, it indicates that a breakdown short circuit or leakage occurs inside the thyristor.Measure the forward and reverse resistance values between gate G and cathode K. Normally, there should be forward and reverse resistance values similar to diodes (the actual measurement results are smaller than those of ordinary diodes), that is, the forward resistance value is small (less than 2 kΩ) and the reverse resistance value is large (greater than 80 kΩ). If the resistance values of the two measurements are both large or small, it means that the thyristor is open or short-circuited between electrode G and K. If the forward and reverse resistance values are equal or close, it indicates that the thyristor has failed, and the PN junction between its electrodes G and K has lost its unidirectional conduction effect.Measure the forward and reverse resistance value between anode A and gate G. In normal conditions, both resistances should be several hundred kiloohms (kΩ) or infinite. If the forward and reverse resistance values are not the same (there is unidirectional conduction like a diode). One of the two PN junctions connected in reverse series between gate G and electrode A has been short-circuited.(3) Detection of triggering capability: For ordinary thyristors with low power (working current is below 5A), it can be measured with R×1 level of the multimeter . During the measurement, the black probe is connected to anode A and the red probe is connected to cathode K. At this time, the watch hand does not move, and the resistance value is displayed as infinite (∞). Use tweezers or wires to make anode A and gate G of the thyristor be short-circuited(see figure 3), which is equivalent to applying a forward trigger voltage to gate G. At this time, if the resistance value is several ohms to tens of ohms (the specific resistance value will vary according to the part number of the thyristor), it indicates that the thyristor is conducting due to the forward trigger. Then disconnect electrode A and gate G(the probes on electrode A and K do not move, only the trigger voltage of gate G is cut off). If the value indicated by the watch hand is still in the position of several ohms to tens of ohms, it indicates that the triggering performance of the thyristor is good. Figure 3. Detection of Triggering CapabilityFor medium and high power ordinary thyristors with a working current above 5 A, the on-state voltage drop VT, holding current IH and the gate trigger voltage Vo are relatively large. The current provided by the R × 1 kΩ level of the multimeter is low, and the thyristor cannot be completely turned on, so a 200Ω adjustable resistor and one to three 1.5 V dry batteries can be connected in series at the end of the black probe (depending on the capacity of the thyristor being tested, if its working current is greater than 100 A, three 1.5 V dry batteries are applied), as shown in figure 4. Figure 4. Detection of Trigger VoltageYou can also use the test circuit in figure 5 to test the triggering capability of an ordinary thyristor. In the circuit, vT is the thyristor under test, HL is a 6.3 V indicator (small electric beads in a flashlight), GB is a 6 V power supply (four 1.5 V dry batteries or 6 V regulated power supply can be used), and S is the button, R is the current limiting resistor. Figure 5. Test Circuit to Test the Triggering CapabilityWhen the button S is not connected, the thyristor VT is in a blocking state, and the indicator light HL is not on (if HL is on at this time, there may be breakdown of vT or leakage damage). After pressing the button S once (turn S on for a moment to provide the trigger voltage for gate G of the thyristor VT), if the indicator HL is always on, it means that the thyristor has a good triggering capability. If the brightness of the indicator is low, it indicates that the thyristor has poor performance and a large conduction voltage drop (the conduction voltage drop should be about 1 V under normal conditions). If button S is on, the indicator light is on, and when button S is off, the indicator light is off, indicating that the thyristor is damaged and the triggering performance is poor.4.2 Detection of TRIAC(1) Discrimination of each electrode: Use the R×1 or R×10 level of the multimeter  to measure the forward and reverse resistance values between three pins of the TRIAC. If it is measured that one pin is not connected with the other two pins, then this pin is the main electrode T2.After finding the electrode T2, the remaining two pins are the main electrode T1 and the gate G3. Measuring the forward and reverse resistance values between these two pins will gain two smaller resistance values. In a measurement with a small resistance value (about tens of ohms), the black probe is connected to the main electrode T1, and the red probe is connected to gate G.One end of the bolt of the bolt-shaped TRIAC is the main electrode T2, the thinner lead end is gate G, and the thicker lead end is the main electrode T1.    The shell of the metal-encapsulated (TO-3) TRIAC is the main electrode T2.The middle pin of the plastic-encapsulated (TO-220) TRIAC is the main electrode T2, which is usually connected to its own small heat sink. Figure 6. Pin Arrangement of Several TRIAC(2) Judging whether it is good or bad: Use the R×1 or R×10 level of a multimeter to measure the forward and reverse resistance values between the main electrode T1 and the main electrode T2 and between the main electrode T2 and gate G of the TRIAC. Normally it should be close to infinity. If the measured resistance values are all very small, it means that the electrodes of the TRIAC have been broken down or are short-circuited.Measure the forward and reverse resistance of the main electrode T1 and gate G. Normally, it should be between tens of ohms (Ω) and one hundred ohms (Ω) (when the black probe is connected to electrode T1 and the red probe is connected to gate G, the measured forward resistance value is slightly smaller than the reverse resistance value). If the forward and reverse resistance values between electrode T1 and gate G are measured to be infinite, it indicates that the thyristor has been damaged by an open circuit.(3) Detection of triggering capability: For small power TRIAC with working current below 8A, it can be measured directly with R×1 level of the multimeter. When measuring, first connect the black probe to the main electrode T2 and the red probe to the main electrode T1, then use tweezers to make electrode T2 and gate G be short-circuited, and add a positive polarity trigger signal to gate G. If the resistance value measured at this time changes from infinity to more than ten ohms (Ω), it means that the thyristor has been triggered to conduct, and the conduction direction is T2 → T1.Then connect the black probe to the main electrode T1, and the red probe to the main electrode T2. Use tweezers to make electrode T2 and gate G be short-circuited, and add a negative polarity trigger signal to gate G. If the resistance value measured at this time changes from infinity to more than ten ohms (Ω), it means that the thyristor has been triggered to conduct, and the conduction direction is T1 → T2.If gate G is disconnected after the thyristor is triggered to be turned on, the low-resistance conduction state cannot be maintained between electrode T2 and T1 and the resistance value becomes infinite, it indicates that the TRIAC has poor performance or is damaged. If a positive (or negative) polarity trigger signal is added to gate G, the thyristor still does not conduct (the forward and reverse resistance values between T1 and T2 are still infinite), then the thyristor is damaged and has no trigger continuity.For medium and high power TRIAC with a working current of 8A or more, when measuring their triggering capability, one to three 1.5V dry batteries can be connected in series to a probe of a multimeter, and then measure by using R×1 level as described above.For a TRIAC with a withstand voltage of 400V or more, its trigger capability and performance can also be tested by using 220V AC voltage.Figure 7 is a test circuit of a TRIAC. In the circuit, FL is a 60W /220V incandescent bulb, VT is the TRIAC under test, R is a 100Ω current limiting resistor, and S is a button. Figure 7. TRIAC CircuitAfter the power plug is connected to the working frequency AC, the TRIAC is in the off-state and the light bulb is off. (If the bulb is glowing normally at this time, it means that electrode T1 and T2 of the thyristor under test have been broken down and short-circuited; if the light bulb is slightly light, it means that the thyristor under test is damaged by leakage). Press the button S once to provide the trigger voltage signal for gate G of the thyristor. In normal conditions, the thyristor should be immediately triggered to turn on, and the light bulb will glow normally. If the bulb fails to emit light, the internal circuit of the tested thyristor is damaged. If the light bulb is turned on when the button S is pressed, and the light bulb is turned off when the button is released, it indicates that the triggering performance of the tested thyristor is poor.When using a multimeter to detect low-power light-controlled thyristors, put the multimeter in R × 1 level, connect one to three 1.5V dry batteries in series to a black probe, and measure the forward and reverse resistance values between the two pins. Normally it should be infinite. Then use a small flashlight or laser pen to illuminate the light receiving window of the light controlled thyristor. At this time, a small forward resistance value can be measured, but the reverse resistance value is still infinite. In a measurement with a small resistance value, the black probe is connected to the anode A, and the red probe is connected to the cathode K.The following method can also be used to measure light-controlled thyristors. Turn on the power switch S and illuminate the light receiving window of the thyristor VT with a flashlight. After adding a trigger light source (high-power light-controlled thyristor has its own light source, as long as the light-emitting diode or semiconductor laser in its optical cable is added with the working voltage, no external light source is required), the indicator EL should be on. After the light source is evacuated, the indicator light EL should remain illuminated. There is only one PN junction. Therefore, you just need to measure electrode A and G with a multimeter.Put the multimeter in the R × 1 kΩ level, and the two probes can be connected to one of the two pins of the thyristor under test (measure their forward and reverse resistance values). If a pair of pins is measured with a low resistance value, the black probe is connected to the anode A, while the red probe is connected to gate G, and the other pin is the cathode K. (2) Judging whether it is good or bad: Use the R×1 level of a multimeter to measure the forward and reverse resistance values between the electrodes of the BTG thyristor. Under normal conditions, the forward and reverse resistances between the anode A and the cathode K are infinite; the forward resistance between the anode A and gate G (when the black probe is connected to electrode A) is several hundred ohms to several thousand ohms and the reverse resistance value is infinite. If the forward and reverse resistance values between two electrodes are measured to be very small, it indicates that the thyristor has been short-circuited and damaged.(3) Detection of triggering capability: Put the multimeter in the R × 1 Ω level, connect the black probe to anode A, and the red probe to cathode K. The measured resistance should be infinite. Then touch gate G with your finger and add a human body induction signal to it. If the resistance between electrodes A and K changes from infinity to low resistance (a few ohms) at this time, it indicates that the thyristor has a good triggering ability. Otherwise, the performance of the thyristor is poor. Frequently Asked Questions about Thyristors1. What is thyristor and its types?A thyristor is a four-layer device with alternating P-type and N-type semiconductors (P-N-P-N). In its most basic form, a thyristor has three terminals: anode (positive terminal), cathode (negative terminal), and gate (control terminal). The gate controls the flow of current between the anode and cathode. 2. What is thyristor diagram?In general, Thyristors are also switching devices similar to the transistors. ... SCR or Thyristor is a four-layered, three-junction semiconductor switching device. It has three terminals anode, cathode, and gate. Thyristor is also a unidirectional device like a diode, which means it flows current only in one direction. 3. Where is thyristor used?Thyristors may be used in power-switching circuits, relay-replacement circuits, inverter circuits, oscillator circuits, level-detector circuits, chopper circuits, light-dimming circuits, low-cost timer circuits, logic circuits, speed-control circuits, phase-control circuits, etc. 4. Why SCR is called Thyristor?Silicon Controlled Rectifier (SCR) is a unidirectional semiconductor device made of silicon. This device is the solid state equivalent of thyratron and hence it is also referred to as thyristor or thyroid transistor. 5. What is thyristor diagram?In general, Thyristors are also switching devices similar to the transistors. ... SCR or Thyristor is a four-layered, three-junction semiconductor switching device. It has three terminals anode, cathode, and gate. Thyristor is also a unidirectional device like a diode, which means it flows current only in one direction.