The Kynix Blog

What is a coupling capacitor?In electronics, capacitive coupling is a type of electronic coupling, which uses capacitance between circuits to transfer energy. This coupling design can produce expected effects, and may also produce some accidental effects. Capacitive coupling usually involves placing capacitors in series circuits to achieve signal coupling.Next, this blog will briefly introduce you the basic information of coupling capacitors, mainly from the following six aspects: definition, coupling, decoupling, coupling mode, principle, and function.What is Coupling Capacitor?CatalogI Definition of coupling capacitorII CouplingIII DecouplingIV Coupling method4.1 Direct coupling4.2 Common impedance coupling4.3 Capacitive coupling4.4 Electromagnetic induction coupling4.5 Radiation coupling4.6 Leakage couplingV Working Principle of Coupling CapacitorVI The role of capacitive couplingFAQI Definition of coupling capacitorCoupling capacitance, also known as electric field coupling or electrostatic coupling, is a coupling method due to the existence of distributed capacitance.Coupling capacitors make the two systems of strong and weak currents coupled and isolated by capacitors, provide high-frequency signal paths, prevent low-frequency currents from entering the weak current system, and ensure personal safety. In addition to the above functions, the coupling capacitor with voltage extraction device can also extract power frequency voltage for protection and reclosing use, and play the role of a voltage transformer.Coupling capacitor II CouplingCoupling refers to the process of signal transmission from the first stage to the second stage, and usually refers to AC coupling when it is not specified.From the circuit point of view, it can always be divided into the driving power supply and the driven load. If the load capacitance is relatively large, the drive circuit must charge and discharge the capacitance to complete the signal jump. When the rising edge is relatively steep, the current is relatively large, so that the drive current will absorb a large power supply current. The inductance and resistance (especially the inductance on the chip pins will bounce). Compared with normal conditions, this current is actually a kind of noise, which will affect the normal operation of the previous stage. This is coupling.Red WIMA CAPIII DecouplingDecoupling refers to taking further filtering measures to the power supply to remove the influence of mutual interference between the two levels of signals through the power supply.The coupling constant refers to the time constant corresponding to the product of the coupling capacitance value and the second-stage input impedance value.The purpose of decoupling1. Remove the high-frequency ripple in the power supply, and cut off the high-frequency signal of the multi-stage amplifier through the crosstalk path of the power supply;2. When working with a large signal, the circuit's demand for power increases, causing power fluctuations, and the influence of power fluctuations on the input stage/high voltage gain stage when the large signal is reduced by decoupling;3. Form a floating ground or floating power supply, and complete the coordination of each part of the ground or power supply in a complex system. The high-frequency switching noise generated by the active device during switching will propagate along the power line. The main function of the decoupling capacitor is to provide a local DC power supply to the active device to reduce the propagation of switching noise on the board and to guide the noise to the ground.WEST-CAPIV Coupling methodThe interference signal generated by the interference source causes electromagnetic interference to the electronic control system through a certain coupling channel. The coupling method of interference is nothing more than acting on the electronic control system through wires, spaces, common lines, etc. There are mainly the following:4.1 Direct couplingDirect coupling is the most direct way of interference intrusion, and it is also the most common way in the system. For example, interference signals directly invade the system through wires and cause interference to the system. For this coupling method, filtering and decoupling can be used to effectively suppress the introduction of electromagnetic interference signals. 4.2 Common impedance couplingCommon impedance coupling is a common coupling method. It often happens when the currents of two circuits have a common path. Common impedance coupling has two types: common ground and power supply impedance. To prevent this coupling, the coupling impedance should be close to zero, so that there is no common impedance between the interference source and the interfered object. 4.3 Capacitive couplingCapacitive coupling, also known as electric field coupling or electrostatic coupling, is a coupling method due to the existence of distributed capacitance. 4.4 Electromagnetic induction couplingElectromagnetic induction coupling is also called magnetic field coupling. It is a coupling method induced by the electromagnetic field in the internal or external space. The common method to prevent this coupling is to shield devices or circuits that are susceptible to interference. 4.5 Radiation couplingThe electromagnetic field radiation can also cause interference coupling, which is an irregular interference. This kind of interference is easily transmitted to the system through the power line. In addition, when the signal transmission line is long, they can radiate and receive interference waves, which is called the antenna effect. 4.6 Leakage couplingThe so-called leakage coupling is resistive coupling. This interference often occurs when the insulation is reduced.Black beautyV Working Principle of Coupling CapacitorWhen the capacitor is connected to the AC circuit, the voltage of the circuit connected to a pin gradually rises, and gradually accumulates charge on the plate where it is located. When the voltage of the circuit connected to the pin drops, the charge accumulated when the potential is high returns to the circuit.TCC V-CAPThe same goes for the other end. The capacitor is insulated, and no current flows through the entire capacitor, but the phenomenon that it accumulates and releases charges as the potential rises and falls, which makes people mistakenly believe that there is current passing. Therefore, it can isolate the DC.The AC signal is coupled to the following circuit components in the form of increasing and decreasing potential at both ends. Capacitors have the characteristics of passing AC and blocking DC. As a coupling capacitor, its function is to allow AC signals to pass normally, while blocking the DC current of the previous amplifier circuit, so that it will not affect the operating point of the next amplifier circuit.Why can the capacitor make the AC current flow and the DC current cannot flow? The two plates of the capacitor can store charge but do not form a loop. The DC current can charge the capacitor, but when the voltage across the capacitor is the same as the power supply voltage, the circuit stabilizes. Therefore, no current will flow; the positive half cycle of the alternating current charges the capacitor, and the negative half cycle first discharges the capacitor. Such continuous charging and discharging are equivalent to current flowing through the capacitor to form a path. VI The role of capacitive couplingThe function of capacitive coupling is to transfer the AC signal from the previous stage to the next stage.Coupling methods include direct coupling and transformer coupling. The direct coupling efficiency is the highest, and the signal is not distorted. However, the adjustment of the working points of the front and rear stages is more complicated and involves each other. In order to prevent the working point of the latter stage from being affected by the previous stage, it is necessary to separate the former stage from the latter stage in terms of direct current.SPRAGUE VQ V-CAPAt the same time, the AC signal can be smoothly transmitted from the previous stage to the next stage. At the same time, the way to accomplish this task is to use capacitor transmission or transformer transmission to achieve. They can transmit AC signals and block DC, so that the working points of the front and rear stages are not involved in each other. But the difference is that when using a capacitor to transmit, the phase of the signal will be delayed, and when using a transformer, the high-frequency component of the signal will be lost.In general, capacitors are often used as coupling elements for small signal transmission, and transformers are often used as coupling elements for large signal or strong signal transmission. FAQ 1. What is meant by coupling capacitor?Coupling capacitors (or dc blocking capacitors) are use to decouple ac and dc signals so as not to disturb the quiescent point of the circuit when ac signals are injected at the input. Bypass capacitors are used to force signal currents around elements by providing a low impedance path at the frequency.2. How does a coupling capacitor work?Definition: A capacitor that is used to connect the AC signal of one circuit to another circuit is known as a coupling capacitor. ... On the o/p end, we get the AC signal. So a coupling capacitor is placed between two circuits so that AC signals supplies while the DC signal is blocked.3. What is the need of coupling capacitor?Coupling capacitors are essential components in amplifier circuits. They are used to prevent interference of a transistor's bias voltage by AC signals. In most amplifier circuits, this is achieved by driving the signal to the base terminal of a transistor through a coupling capacitor.4. What is coupling and decoupling capacitor?A decoupling capacitor is a capacitor used to decouple one part of an electrical network (circuit) from another. ... In analog circuits, a coupling capacitor is used to connect two circuits such that only the AC signal from the first circuit can pass through to the next while DC is blocked.5. Why decoupling capacitor is used?A decoupling capacitor acts as a local electrical energy reservoir. Capacitors, like batteries, need time to charge and discharge. When used as decoupling capacitors, they oppose quick changes of voltage. ... Decoupling capacitors are used to filter out voltage spikes and pass through only the DC component of the signal. 6. How do I choose a coupling capacitor?A coupling capacitor is best selected so that its impedance is as low as possible at the frequency of interest. The impedance magnitude at any frequency is easily calcu- lated as: Since the net reactance is zero at the capaci- tor's FSR, the total impedance will be equal to the ESR at this frequency. 7. What is the value of coupling capacitor?C is the coupling cap value, w is the angular frequency 2*pi*f with f the frequency in Hertz. Units of resistance Ohms, capacitance Farads. The reason for this is because the three components form a voltage divider and the output only appears across R2 the output resistor. 8. What is coupling capacitor and bypass capacitor?Coupling capacitors (or dc blocking capacitors) are use to decouple ac and dc signals so as not to disturb the quiescent point of the circuit when ac signals are injected at the input. Bypass capacitors are used to force signal currents around elements by providing a low impedance path at the frequency. 9. What happens when coupling capacitor is removed?Since capacitor blocks DC, former stage do not affect DC biasing of succeeding stage. Disadvantage of coupling capacitor is, it put limit on low frequency response of the amplifier. Another disadvantage is, capacitor coupled amplifier, can not be used for amplifying DC signal. 10. How do you calculate the value of coupling capacitor?Measure, calculate or determine from a manufacturer's data sheet the input impedance of the circuit to which the coupling capacitor is connected. Multiply this number by 1/10 to find the minimum value of the coupling capacitor's impedance.

IntroductionWhat is the IC package? To put it simply, chip packaging is the process of placing a bare integrated circuit chip produced in a foundry on a load-bearing substrate, leading the pins out, and then fixing the package as a whole. It is analogous to the chip's shell, which can wrap, fix, and seal the chip to protect it from external forces such as water, air, moisture, chemicals, and so on.With the continuous improvement of IC packaging, there are more and more types of IC packaging. Various IC packaging packages types, names, logos, etc. can sometimes be confusing. This blog will give you a brief introduction to IC packaging related content, which mainly includes the following three parts: common IC brand identification, IC package terminology, classification of IC packaging, and hope to help you further effectively distinguish and understand IC packaging. Catalog IntroductionEvolution of IC Packaging TypeIC Packaging Types10 Common IC Brand Identification71 kinds of IC package terminology   explainedFAQ Evolution of IC Packaging TypeIn the early stage of the development of chip packaging, there are mainly two types: 1. Through-hole package2. Surface mount packageThrough hole package mainly includes Dual In-line Package (DIP), Transistor Outline (TO), Pin Grid Array (PGA) and so on. Through-hole packageSurface mount package includes TO-252 (D-PAK), Small-Outline Transistor (SOT), Small Outline Package (SOP), Plastic Quad Flat Package (QFP), Plastic Leaded Chip Carrier (PLCC) and so on.Surface mount packageDue to the increasing demand of the surface mount market, the earlier through-hole TO packaging has also begun to develop to the surface mount mode. For example, DPAK packaging, which is easy for many people to confuse, actually refers to TO-252, D2PAK refers to TO-263 and D3PAK refers to TO-268.In the middle and later stage, chip packaging began to enter the era of area array packaging. During this period, packaging types such as Ball Grid Array Package (BGA), Chip Scale Package (CSP), Quad Flat No-lead Package (QFN) and Multi-Chip Module (MCM) began to become popular.With the further development of packaging technology, some chips have begun to adopt the latest three-dimensional stacking packaging technology. IIC Packaging TypesAccording to the different port direction, the common IC packages can be divided into four categories: unilateral, bilateral, four-sided and matrix and several types can be subdivided from the above four categories according to different packaging forms and port shapes. Please refer to the following table for details. IC packaging types In addition, according to the material medium, IC packaging can also be divided into metal, ceramic, plastic and other types, generally distinguished by prefix. For example, "C" refers to ceramic package, "H" refers to package with heat sink and "P" refers to plastic package. 10 Common IC Brand IdentificationMany integrated circuit models’ prefix is often the abbreviation of the manufacturer's name. If you see the following prefix model, you might as well check the corresponding brand first. Of course, this method is not entirely feasible. So you still have to refer to the PDF file of the specific product according to the actual situation.1. AMDThose prefixed with AM are all AMD products, and there are also some confusion between the prefix PAL, CYPRESS and TI. The specific situation should be determined by checking the information.2. ATMELThose prefixed with AT are ATMEL products.3. CYPRESSThose prefixed with CY are all CYPRESS products, and some of them are confused with prefix PALC, PALCE and TI.4. NSCThose prefixed with DM, LF, LM, DS, etc., are basically NSC products. NSC has many product series with other prefix, but the specific situation should be determined by checking the information.5. AD：Those prefixed with AD, OP are AD brand. AD has many other series, such as prefix: DAC, ADG, ADSP and many other series.6. INTERSIL：Those prefixed with HI1, HI2, HI3, HI4, HA1, HA2, HA3, HA4, CA, ICL, ICM, ID, IS, etc., are INTERSIL products. There is also some confusion between prefix MD and INTEL.7. IDT：The prefix for IDT products is almost the prefix IDT.8. MAXThe prefix for MAX products is almost the prefix MAX.9. AGILENTCommon prefixes are HCPL, HDSP, HSSR, and so on.10. ALTERAThe prefix for ALTERA products is almost the prefix for EPM. IC package Figure (105 kinds in total)71 kinds of IC package terminology explainedStill not sure what some IC packaging terms mean exactly? Here is a list of 71 common IC packaging terms for you.1. BGA (Ball Grid Array)BGA is one of the surface mount packages. Spherical bumps are made on the back of the printed substrate to replace pins. LSI chips are assembled on the front of the printed substrate, and then sealed by molding resin or filling method. It is also known as Pad Array Carrier (PAC) and the number of pins can exceed 200. It is a kind of package for multi-pin LSI.The package was developed by Motorola and was first used in portable phones and other devices. 2. BQFP (Quad Flat Package with Bumper)BQFP is one of the QFP packages that is provided with protrusions (cushions) at the four corners of the package body to prevent bending deformation of the pins during transportation. American semiconductor manufacturers mainly use this package in microprocessors and Asic circuits. The center distance of the pin is 0.635 mm, and the number of pins ranges from 84 to 196. (see QFP). 3. Butt Joint PGA (Butt Joint Pin Grid Array)Butt Joint PGA is an alias for surface mount PGA (see Surface Mount PGA) 4. C- (Ceramic)C- is a mark that represents a ceramic package and is often used in practice. For example, CDIP represents Ceramic DIP. 5. CerdipThe Ceramic Dual In-line Package sealed with glass is for circuits such as ECL RAM, DSP (Digital Signal Processor). Cerdip with glass window is used for ultraviolet erasing EPROM and microcomputer circuit with EPROM. The center distance of the pin is 2.54 mm, and the number of pins ranges from 8 to 42. In Japan, this package is represented as DIP-G (G means glass seal). 6. CerquadOne of the surface mount packages, that is, the lower sealed Ceramic QFP, is used to package logic LSI circuits such as DSP. Cerquad with windows is used to package EPROM circuits. The heat dissipation is better than that of Plastic QFP, and power ranges from 1.5 to 2W can be allowed under natural air cooling conditions. But the cost of packaging is 3 to 5 times higher than that of Plastic QFP. Pin center distance has 1.27 mm, 0.8 mm, 0.65 mm, 0.5 mm, 0.4 mm and other specifications. The number of pins ranges from 32 to 368. 7. CLCC (Ceramic Leaded Chip Carrier)Ceramic Leaded Chip Carrier is one of the surface mount packages, and the pins are drawn from the four sides of the package in T-shaped. Those with windows are used for packaging ultraviolet erasing EPROM and microcomputer circuit with EPROM, etc. This packaging is also known as QFJ and QFJ-G (see QFJ). 8. COB (Chip on Board)Chip on Board package is one of the bare chip mounting technologies. The semiconductor chip is connected and mounted on the printed circuit board, the electrical connection between the chip and the substrate is realized by the lead stitching method. Next, cover it with resin to ensure its reliability. Although COB is the simplest bare chip mounting technology, its packaging density is far lower than that of TAB and reverse chip welding technology. 9. DFP (Dual Flat Package)Dual Flat Package is another name for SOP (see SOP). This was once called in the past, but now it is basically out of use.10. DIC (Dual In-line Ceramic Package)This is another name for Ceramic DIP (including glass seal) (see DIP). 11. DIL (Dual In-Line)DIL is an alias for DIP (see DIP). European semiconductor manufacturers often use this name. 12. DIP (Dual In-line Package)Dual In-line Package is one of the through hole packages. The pins are drawn from both sides of the package, and the packaging materials are plastic and ceramic. DIP is the most popular through-hole package, including standard logic IC, memory LSI, microcomputer circuit and so on. The center distance of the pin is 2.54 mm, and the number of pins ranges from 6 to 64. The packaging width is usually 15.2 mm. Some refer to packages with widths of 7.52 mm and 10.16 mm as skinny DIP and slim DIP (narrow DIP, respectively). In most cases, however, it is indistinguishable and is simply collectively referred to as DIP. In addition, Ceramic DIP sealed with low melting point glass is also known as Cerdip (see Cerdip). 13. DSO (Dual Small Out-lint)DSO is the alias for SOP (see SOP). Some semiconductor manufacturers use this name. 14. DICP (Dual Tape Carrier Package)DICP is one of the TCP (loaded packages). The pins are made on the insulation tape and drawn from both sides of the package. Due to the use of TAB (Tape Automated Bonding) technology, the package shape is very thin. It is commonly used in liquid crystal display drive LSI, but most of them are customized products. In addition, the 0.5 mm thick memory LSI thin package is in the development stage. In Japan, DICP is named DTP according to the standard of EIAJ (Japanese Electronic Machinery Industry). 15. DIP (Dual Tape Carrier Package)As we mentioned above, it is the name of DTCP in the standard of the Japanese Electronic Machinery Industry Association. (see DTCP). 16. FP (Flat Package)FP is one of the surface mount packages and it is another name of QFP or SOP (see QFP and SOP). Some semiconductor manufacturers use this name.17. Flip-chipFlip-chip is one of the bare chip packaging technologies. The metal bump is made in the electrode region of the LSI chip, and then the metal bump is connected to the electrode area on the printed substrate by pressure welding. The occupied area of packaging is basically the same as the size of the chip, which is the smallest and thinnest of all packaging technologies. 18. FQFP (fine pitch quad flat package)FQFP usually refers to the QFP which the center distance of the pin is less than 0.65 mm (see QFP). Some conductor manufacturers use this name.19. CPAC (Globe Top PAD Array Carrier)CPAC is another name for BGA by Motorola in the United States. 20. CQFP (Quad Fiat Package with Guard Ring)CQFP is one of the plastic QFP. The pins are masked with a resin protective ring to prevent bending deformation. Before assembling the LSI on the printed substrate, we need to cut off the pin from the protective ring and make it become L-shaped. This package has been mass produced by Motorola in the United States. The center distance of the pin is 0.5 mm, and the maximum number of pins is about 208.21. H- (with heat sink)H- represents a mark with a heat sink. For example, HSOP represents a SOP with a heat sink.22. Pin Grid Array (surface mount type)PGA is usually a through-hole package with a pin length of about 3.4 mm. The surface mount PGA has display–shaped pins on the bottom of the package, ranging in length from 1.5 mm to 2.0 mm. Mounting uses the method of butt joint with the printed substrate, so it is also known as butt joint PGA. Because the center distance of the pin is only 1.27 mm, which is half smaller than the through-hole PGA, the package body cannot be made very large, and the number of pins is more than the through-hole type (ranges from 250 to 528). It is a package for large-scale logical LSI. The packaging substrate has a multi-layer ceramic substrate and a glass epoxy resin printing base. Packaging based on multi-layer ceramic substrate has been practical. 23. JLCC (J-Leaded Chip Carrier)JLCC refers to the alias for windowed CLCC and windowed Ceramic QFJ (see CLCC and QFJ). The name used by some semiconductor manufacturers. 24. LCC (Leadless chip carrier)LCC refers to a surface mount package with only electrode contact and no pin on the four sides of the ceramic substrate. It is a high-speed and high-frequency IC package, also known as Ceramic QFN or QFN-C (see QFN). 25. LGA (Land Grid Array)LGA , that is, an array state flat electrode contact package made on the bottom surface. All we need to do is to insert the socket when assembling. Ceramic LGA, with 227 contacts (1.27 mm center distance) and 447 contacts (2.54 mm center distance) has been used in high speed logic LSI circuits. LGA can accommodate more input and output pins in a smaller package than QFP. In addition, because of the small impedance of the lead, it is very suitable for high-speed LSI. However, due to the complexity of socket production and high cost, it is basically not used much now. But the demand for it is expected to increase in the future. 26. LOC (Lead on Chip)LOC is one of the LSI packaging technologies. The front end of the lead frame is located at the top of the chip. A convex solder joint is made near the center of the chip, and the lead is stitched for electrical connection. Compared with the original structure in which the lead frame is arranged near the side of the chip, the chip contained in the package of the same size is up to about 1 mm wide. 27. LQFP (Low Profile Quad Flat Package)LQFP is a kind of QFP whose package body thickness is 1.4 mm and this is the name used by the Japanese Electronics and Machinery Industry according to the new QFP shape specification. 28. L-QUADL-QUAD is one of the Ceramic QFP. The thermal conductivity of aluminum nitride for packaging substrate is 7 to 8 times higher than that of alumina and has good heat dissipation. The frame of the package is sealed with alumina and the chip is sealed by filling method, thus the cost is suppressed. It is a package developed for logical LSI that allows 3 w power under natural air cooling conditions. LSI logic packages with 208 pins (0.5 mm center distance) and 160 pins (0.65 mm center distance) have been developed and put into mass production in October 1993. 29. MCM (Multi-Chip Module)MCM is a package that assembles multiple bare semiconductor chips on a wiring substrate. According to the substrate materials, it can be divided into MCM-L, MCM-C and MCM-D. MCM-L is a module that uses the usual glass epoxy resin multi-layer printed substrate. The wiring density is not that high and the cost is low. MCM-C is a module which uses thick film technology to form multi-layer wiring and uses ceramics (alumina or glass-ceramic) as substrate, which is similar to mixing IC with thick film of multi-layer ceramic substrate. There is no significant difference between them, and the wiring density was higher than that of MCM-L.MCM-D is a module which uses thin film technology to form multi-layer wiring and uses ceramics (alumina or aluminum nitride) or Si and Al as substrate. The wiring density is the highest of the three modules, but the cost is also high. 30. MFP (Mini Flat Package)MFP is another name for plastic SOP or SSOP (see SOP and SSOP) and it is used by some semiconductor manufacturers. 31. MQFP (Metric Quad Flat Package)MQFP is a classification of QFP according to the JEDEC standard. It refers to standard QFP with a pin center distance of 0.65 mm and a body thickness of 3.8 mm~2.0 mm (see QFP). 32. MQUAD (Metal Quad)MQUAD is a kind of QFP package developed by Olin Company in the United States. The substrate and cover are made of aluminum and sealed with adhesive. The power of 2.5 w~2.8 w can be allowed under the condition of natural air cooling. SHINKO ELECTRIC INDUSTRIES CO., LTD. was licensed to start production in 1993. 33. MSP (Mini Square Package)MSP is another name for QFI (see QFI) and is often called in the early days of development. QFI is the name specified by the Electronic Machinery Industry Association of Japan. 34. OPMAC (Over Molded Pad Array Carrier)OPMAC is the name used by Motorola for molded resin seal BGA (see BGA). 35. P- (plastic)P- is the mark that represents a plastic package. For example, PDIP represents Plastic DIP. 36. PAC (Pad Array Carrier)PAC is an alias for BGA (see BGA). 37. PCLP (Printed Circuit Board Leadless Package)Fujitsu of Japan uses the name for Plastic QFN (Plastic LCC) (see QFN). The center distance of the pin can be divided into two specifications: 0.55 mm and 0.4 mm. It is currently in the development phase. 38. PFPF (Plastic Flat Package)PFPF is an alias for Plastic QFP (see QFP) and it is used by some LSI manufacturers. 39. PGA (Pin Grid Array)PGA is one of the through-hole packages, and the vertical pins on the bottom are arranged in the form of display. The packaging substrate is basically multi-layer ceramic substrate. In the case of not specifically indicating the name of the material, most of the Ceramic PGA, are used in high-speed and large-scale logic LSI circuits. The cost is high. The center distance of the pin is usually 2.54 mm, and the number of pins ranges from 64 to 447. In order to reduce the cost, the packaging substrate can be replaced by glass epoxy resin printing substrate. There is also Plastic PGA with 64 to 256 pins. In addition, there is a short pin surface mount PGA (Butt Joint PGA) with a pin center distance of 1.27 mm. (see Surface Mount PGA). 40. Piggy BackIt refers to a ceramic package with sockets and its shape is similar to that of DIP, QFP and QFN. It is used to confirm operation on the evaluation program when developing a device with a microcomputer. For example, plug the EPROM into the socket for debugging. This kind of package is basically custom-made, and there is little circulation on the market. 41. PLCC (Plastic Leaded Chip Carrier)PLCC is one of the surface mount packages. The pin is drawn from the four sides of the package in the shape of T and is made of plastic. Texas Instruments was first used in 64k-bit DRAM and 256k-bit DRAM, and now it has been widely used in logic LSI, DLD (or logic device) and other circuits. The center distance of the pin is 1.27 mm, and the number of pins ranges from 18 to 84. The J-shaped pin is not easy to deform and is easier to operate than QFP, but the appearance inspection after welding is more difficult.PLCC is similar to LCC (also known as QFN). In the past, the only difference between the two was that the former used plastic and the latter used ceramics. But now there are J-shaped pin packages made of ceramics and pin-free packages made of plastic. (marked as plastic LCC, PC LP, P-LCC, etc.) Thus they have been unable to distinguish.To this end, the Japanese Electronics and Machinery Industry decided in 1988 to refer to packages with J-shaped pins on four sides as QFJ, and packages with electrode bumps on four sides as QFN (see QFJ and QFN). 42. P-LCC (Plastic Leadless Chip Carrier)Sometimes it is another name for Plastic QFJ, sometimes it is another name for QFN (Plastic LCC) (see QFJ and QFN). Some LSI manufacturers use PLCC for lead package and P-LCC for lead-free package to show the difference. 43. QFH (Quad Flat High Package)QFH is a kind of Plastic QFP. In order to prevent the package body from breaking, the QFP body is made thicker (see QFP). This is the name used by some semiconductor manufacturers. 44. QFI (Quad Flat I-leaded Package)QFI is one of the surface mount packages. The pin is drawn from the four sides of the package in I-shaped. It is also known as MSP (see MSP). The mount is connected with the printed substrate by butt joint. Because there is no protruding part of the pin, the occupied area of the mount is smaller than that of QFP. Hitachi has developed and used this package for video analog IC. In addition, this package is also used by PLL IC of Motorola, a Japanese company. The center distance of the pin is 1.27 mm, and the number of pins is from 18 to 68.45. QFJ (Quad Flat J-leaded Package)QFJ is one of the surface mount packages. The pin is drawn from the four sides of the package in the shape of J. It is the name stipulated by the Japan Electronic Machinery Industry Association. The center distance of the pin is 1.27 mm. There are two kinds of materials: plastic and ceramics. Plastic QFJ is mostly called PLCC (see PLCC), and it is for microcomputers, gate displays, DRAM, ASSP, OTP, etc. The number of pins ranges from 18 to 84. Ceramic QFJ is also known as CLCC and JLCC (see CLCC). The windowed package is used for ultraviolet erasing EPROM and microcomputer chip circuits with EPROM. The number of pins ranges from 32 to 84.46. QFN (Quad Flat Non-leaded Package)QFN is one of the surface mount packages and it is often called LCC now. QFN is the name specified by the Electronic Machinery Industry Association of Japan. The four sides of the package are equipped with electrode contacts. Because there are no pins, the mounting area is smaller than QFP, and the height is lower than QFP. However, when there is a stress between the printed substrate and the package, it cannot be alleviated at the electrode contact. Therefore, it is difficult for electrode contacts to make as many pins as QFP. The number of pins is generally ranges from 14 to 100.There are two kinds of materials: ceramic and plastic. When marked with LCC, they are basically Ceramic QFN. The center of the electrode contact is 1.27 mm.Plastic QFN is a low-cost package for printing substrate with glass epoxy resin. In addition to 1.27 mm, there are two kinds of electrode contact center distance: 0.65 mm and 0.5 mm. This package is also known as Plastic LCC, PCLC, P-LCC and so on.47. QFP (Quad Flat Package)QFP is one of the surface mount packages, with pins drawn from four sides in L-shaped. There are three kinds of substrate: ceramic, metal and plastic. In terms of quantity, plastic packaging accounts for the vast majority. When the material is not specifically indicated, most of the cases are Plastic QFP. Plastic QFP is the most popular multi-pin LSI package. It is not only used in microprocessor, gate display and other digital logic LSI circuits, but also in VTR signal processing, audio signal processing and other analog LSI circuits. The center distance of pin has 1.0 mm, 0.8 mm, 0.65 mm, 0.5 mm, 0.4 mm, 0.3 mm and other specifications. The maximum number of pins in the 0.65 mm center distance specification is 304.In Japan, QFP with a pin center distance less than 0.65 mm is called QFP (FP). But now the Japanese Electronics and Machinery Industry will re-evaluate the shape of the QFP. There is no difference in the center distance of the pin. But according to the thickness of the package body, it can be divided into three types: QFP (2.0 mm~3.6 mm thickness), LQFP (1.4 mm thickness) and TQFP (1.0 mm thickness).In addition, some LSI manufacturers specifically refer to the QFP with the pin center distance as 0.5 mm as shrink QFP or SQFP, VQFP.However, some manufacturers also call the QFP with pin center distance of 0.65 mm and 0.4 mm SQFP, which makes the name a little confused. The disadvantage of QFP is that when the center distance of the pin is less than 0.65 mm, the pin is easy to bend. In order to prevent pin deformation, several improved QFP varieties have emerged such as BQFP with tree finger buffer pads on the four corners of the package (see BQFP); GQFP with a resin protection ring which covers the front of the pin (see GQFP) and TPQFP (see TPQFP)，which is set test bumps in the package body and can be tested in a special fixture to prevent pin deformation.In the aspect of logical LSI, many development products and highly reliable products are packaged in multi-layer ceramic QFP. Products with a minimum pin center distance of 0.4 mm and a maximum number of pins of 348 have also been introduced. In addition, there are glass-sealed ceramic QFP.48. QFP (FP) (QFP fine pitch)This is the name specified in the standard of the Japan Electronic Machinery Industry Association. The pin center distance is 0.55 mm, 0.4 mm, 0.3 mm and so on, which is smaller than that of 0.65 mm (see QFP).49. QIC (Quad In-line Ceramic Package)QIC is another name for Ceramic QFP and it is used by some semiconductor manufacturers (see QFP, Cerquad).50. QIP (Quad In-line Plastic Package)QIP is another name for Ceramic QFP and is used by some semiconductor manufacturers (see QFP, Cerquad).51. QTCP (Quad Tape Carrier Package)QTCP is one of the TCP packages that forms pins on the insulation tape and leads out from the four sides of the package. It is a thin package using TAB technology (see TAB, TCP).52. QTP (Quad Tape Carrier Package)QTP is the name used by the Japanese Electronic Machinery Industry for the shape specifications developed by QTCP in April 1993 (see TCP).53. QUIL (Quad In-Line)QUIL is an alias for QUIP (see QUIP).54. QUIP (Quad In-line Package)The pin is drawn from both sides of the package and bends down into four columns at every other pin. The pin center distance is 1.27 mm. When inserted into the printed substrate, the insertion center distance becomes 2.5 mm. Therefore, it can be used for standard printed circuit boards.It is smaller package than the standard DIP. Nippon Electric has adopted this kind of package in microcomputer chips for desktop computers and household appliances. There are two kinds of materials: ceramics and plastics. The number of pins is 64. 55. SDIP (Shrink Dual In-line Package)SDIP is one of the through-hole packages with the same shape as the DIP. Its pin center distance (1.778 mm) is less than DIP (2.54 mm) so it gets this name. The number of pins ranges from 14 to 90. It is also known as SH-DIP. There are two kinds of materials: ceramics and plastics.56. SH-DIP (Shrink Dual In-line Package)SH-DIP is the same as SDIP and it is used by some semiconductor manufacturers. 57. SIL (Single In-Line)SIL is an alias for SIP (see SIP). European semiconductor manufacturers often use this name. 58. SIMM (Single In-line Memory Module)A memory module provided with electrodes only near one side of the printed substrate. It usually refers to a module inserted into a socket. The standard SIMM has two specifications: 30 electrodes with center distance of 2.54 mm and 72 electrodes with center distance of 1.27 mm. The SIMM with 1 megabit and 4 megabit DRAM packaged with SOJ on one or both sides of the printed substrate has been widely used in personal computers, workstations and other devices. There are at least 30 to 40 percent of DRAM is installed in SIMM. 59. SIP (Single In-line Package)The pins are drawn from one side of the package and arranged in a straight line. The package is laterally mounted on the printed substrate. The center distance of the pin is usually 2.54 mm, and the number of pins ranges from 2 to 23, most of which are customized products. Packages come in different shapes. Sometimes packages with the same shape as ZIP are called SIP.60. SK-DIP (Skinny Dual In-line Package)SK-DIP is a kind of DIP which has a narrow body with a width of 7.62 mm and a pin center distance of 2.54 mm. It is often collectively referred to as DIP (see DIP).61. SL-DIP (Slim Dual In-line Package)SL-DIP is a kind of DIP which has a narrow body with a width of 10.16 mm and a pin center distance of 2.54 mm. It is commonly referred to as DIP. 62. SMD (Surface Mount Devices)Occasionally, some semiconductor manufacturers classify SOP as SMD (see SOP).63. SO (Small Out-line)SO is another name for SOP and is used by many semiconductor manufacturers in the world. (see SOP).64. SOI (Small Out-line I-leaded Package)SOI is one of the surface mount packages. The pin is drawn down from both sides of the package in I-shaped, with a center distance from 1.27 mm and 26 pins. The occupied area of mounting is smaller than that of SOP. Hitachi uses this package in analog IC (IC for motor drive).65. SOIC (Small Out-line Integrated Circuit)SOIC is an alias for SOP (see SOP). Many semiconductor manufacturers abroad use this name.66. SOJ (Small Out-Line J-Leaded Package)SOJ is one of the surface mount packages. The pin is J-shaped from both sides of the package, so it gets its name. They are usually plastic products and are used in memory LSI circuits such as DRAM and SRAM. But most of them are used in DRAM.Many of the DRAM devices packaged in SOJ are mounted on SIMM. The center distance of the pin is 1.27 mm, and the number of pins ranges from 20 to 40 (see SIMM).67. SOL (Small Out-Line L-leaded Package)The name used for SOP in accordance with the JEDEC standard (see SOP).68. SONF (Small Out-Line Non-Fin)SONF is the SOP without heat sink. As the same as the usual SOP, the NF (non-fin) mark is intentionally added In order to show that there is no heat sink in the power IC package. The name is used by some semiconductor manufacturers (see SOP).69. SOF (Small Out-Line Package)SOF is one of the surface mount packages with pins drawn from both sides of the package in L-shaped. There are two kinds of materials: plastic and ceramics. And it is also known as SOL and DFP.SOP is not only used for memory LSI, but also widely used in small-scale ASSP and other circuits. SOP is the most popular surface mount package in areas where the input and output terminals do not exceed 10 to 40. The center distance of the pin is 1.27 mm, and the number of pins is from 8 to 44.In addition, a SOP with a pin center distance less than 1.27 mm is also known as a SSOP. A SOP with assembly height less than 1.27 mm is called TSOP (see SSOP, TSOP). There is also a SOP with a heat sink. 70. SOW [Small Outline Package(Wide-Type)]SOW refers to wide body SOP and this name is used by some semiconductor manufacturers.71. COG (Chip on Glass)COG (Chip on Glass) packaging technology, which has great influence on the development of Liquid Crystal Display (LCD) technology, is becoming more and more practical in the world.FAQ 1. What is package in IC?The case, known as a "package", supports the electrical contacts which connect the device to a circuit board. In the integrated circuit industry, the process is often referred to as packaging. Other names include semiconductor device assembly, assembly, encapsulation or sealing.2. What are the different types of IC packages?What is IC packaging?DIP (Double In-line Package)SOP/SOIC/SO (Small Outline Package)QFP (Quad Flat Package)QFN/LCC (Quad Flat Non-leaded Package)BGA (Ball Grid Array Package)CSP (Chip Scale Package)3. What is IC and how it works?An integrated circuit, or IC, is small chip that can function as an amplifier, oscillator, timer, microprocessor, or even computer memory. An IC is a small wafer, usually made of silicon, that can hold anywhere from hundreds to millions of transistors, resistors, and capacitors.4. What are the types of ICs?Below is the classification of different types of ICs basis on their chip size.SSI: Small scale integration. 3 – 30 gates per chip.MSI: Medium scale integration. 30 – 300 gates per chip.LSI: Large scale integration. 300 – 3,000 gates per chip.VLSI: Very large scale integration. More than 3,000 gates per chip.5. How do I know my IC type?How to Identify Integrated Circuit ChipsIdentify the manufacturer first. ...Look up data sheets in the manufacturer's printed catalog. ...Look up a part number in an electronic retailer's catalog. ...Use the technical specifications for a piece of equipment to find part numbers and alternates.6. What is the most common type of digital IC package?DIP (Dual in-line packages)DIP, short for dual in-line package, is the most common through-hole IC package you'll encounter. These little chips have two parallel rows of pins extending perpendicularly out of a rectangular, black, plastic housing.7. What are the advantages of IC?The advantages of ICs : (i) Extremely small in size, (ii) Low power consumption, (iii) Reliability, (iv) Reduced cost, (v) Very small weight and (vi) Easy replacement. 8. What is the IC package?What Is the Package in IC? IC packaging refers to the material that contains a semiconductor device. The package is a case that surrounds the circuit material to protect it from corrosion or physical damage and allow mounting of the electrical contacts connecting it to the printed circuit board (PCB). 9.Why IC packaging is important?IC packaging is the ability to provide more and more I/O interconnections to a die (bare chip) that is increasingly shrinking in size is an ever-present problem.10. What are the three basic types of linear IC packages?IC packages can be grouped into three general categories; Dual In-line Packages, Chip Carriers and Grid Arrays. All the packages, regardless of the category has a body style that scales with pin count.

Nanotechnology, a technology on a microscopic scale that is indiscernible to the human eye, is gradually having a huge impact on human electronic information, manufacturing, energy, environment and medical care. Mobile phones, computers, cosmetics, sunglasses, tennis rackets, bicycles ...... many of your daily necessities are or have been used in nanotechnology.Want to learn more about what is nanotechnology? Click on the video below or scroll down to see more content!What is Nanotechnology? CatalogI. What is nanotechnology?II. Nano products in consumer marketIII. Small, energy-efficient, bendable screen   digital productsIV. Energy saving and environmental   protectionV. Cancer diagnosis and treatmentVI. Nanotechnology risk alertFAQI. What is nanotechnology?Nanoscience is the science that studies the interactions, composition, properties and fabrication methods of matter at the nanoscale (between atomic and molecular to submicron scales). At such small scales, the physical, chemical and biological properties of materials are vastly different compared to those of macroscale objects.A research report prepared by Springer Nature, the National Center for Nanoscience and the Documentation and Information Center of the Chinese Academy of Sciences shows that nanotechnology promotes multidisciplinary cross-fertilization and breeds numerous opportunities for scientific and technological breakthroughs and original innovations. At the same time, nanotechnology will have a huge impact on people's production and life with the birth of high technology.II. Nano products in consumer marketDue to their ideal mechanical, chemical, electrical, thermal or optical properties, new nanomaterials are used in daily necessities and industrial manufacturing.It is estimated that there are more than 1,600 nanotechnology-based consumer products on the market, including lightweight and rigid tennis rackets, bicycles, luggage, auto parts and rechargeable batteries.Ordinary hair dryers or hair straighteners may use nanomaterials to reduce weight or extend service life. Sunscreens have used sunscreen ingredients such as nano-titanium dioxide or zinc oxide that are invisible on the skin surface. Nano-engineered fibers are used to make anti-wrinkle and anti-staining clothes, which are not only light in weight but also prevent the growth of bacteria.In the manufacturing industry, nanostructured materials are used in surface coatings or lubricants for machine parts to reduce wear and extend the service life of the machine. Alloys with nanostructures are ideal high-performance materials for the manufacture of aircraft and aerospace parts due to their high strength, durability and light weight. They are used in the manufacture of airframes, filter materials and other parts to bring stronger corrosion resistance, earthquake resistance and fire resistance.Nano particles of metals, oxides, carbon and other compounds are also good catalysts, and have important industrial applications in petroleum refining, biofuels and other fields.III. Small, energy-efficient, bendable screen digital productsNanotechnology, a key driver for the information technology and digital electronics industry, has further enhanced the performance of many electronic products, such as computers, cell phones and TVs, the study says.Due to the advancement of nanotechnology, integrated chips and transistors have become smaller and smaller, but the calculation speed has increased day by day. In 2016, the world's first 1-nanometer transistor was born. The transistor is made of carbon nanotubes and molybdenum disulfide instead of silicon, demonstrating the potential to further reduce the size of electronic devices.Scientists’ in-depth understanding of the physical properties of nanomaterials has promoted the development of quantum devices, achieved high-speed data transmission with lower energy consumption, and improved the performance and security of information systems.Zhu Xing, chief scientist of the National Nanoscience Center, said that one application area of quantum dots or inorganic semiconductor nanocrystals is the display screen industry. Based on nanotechnology, the display screens of TVs, computers and mobile devices can achieve ultra-high definition, energy saving, and even bendable, and produce more realistic images. People use carbon nanotubes or silver nanowires when designing new transparent conductive materials, which opens the door to the development of various electronic devices that use flexible screens.IV. Energy saving and environmental protectionAccording to experts, nanotechnology can promote the development of alternative energy sources, improve energy efficiency, and provide new solutions for environmental governance.Based on nanotechnology or new catalysts, oil and natural gas extraction and fuel combustion have become more efficient, which reduces pollution and energy consumption of power plants, vehicles and other heavy equipment.Scientists use nano-engineering to improve the performance of solar photovoltaic power generation equipment and reduce costs. Nanomaterials can also be used for waste heat conversion, such as converting car exhaust into useful energy.For another example, scientists have developed nano-particles that can convert carbon dioxide into clean fuel methane, and nano-photocatalysts that can increase the production capacity of hydrogen, which provide the prospect of developing new renewable energy sources.Nano-structured electrode materials can be used to increase the capacity and performance of rechargeable batteries, reduce battery weight, and thereby improve the efficiency and endurance of electric vehicles.In addition, nanotechnology can also be used for water treatment and pollutant cleaning. For example, nanomaterials such as molybdenum disulfide film can promote the desalination of salt water with more efficient filterability, while porous nanomaterials can absorb heavy metals and slicks in water like a sponge to absorb toxic substances such as heavy metals and slick oil.In addition, nanofibers can absorb tiny particles in the air, so they can be used as a filter to purify the air.The application of nanotechnology in environmental governance also includes the detection of pollutants in air, water and soil. Due to their unique chemical and physical properties, nanoparticles are more sensitive to chemical or biological reagents, so they can be used in sensors to identify toxic substances, which is simpler and faster than traditional methods, and can even remove pollutants while detecting.V. Cancer diagnosis and treatmentAccording to experts, nanotechnology has an increasingly significant impact on the medical and health industries, and has been steadily developed in medical applications such as drug delivery, biomaterials, imaging, diagnosis, and active implants.According to the research report, perhaps the most eye-catching application of nanotechnology in biomedicine is the emergence of the so-called nanopore gene sequencing technology. Its working principle is to use an electric field to drive each single DNA strand through a nano-sized hole in the film, that is, a nanopore.When a single strand of DNA passes through the nanopore, the current change generated on the hole is recorded, thereby identifying the gene coding sequence on the single strand. This technology is expected to significantly reduce the cost of gene sequencing and increase the speed of sequencing.Another promising medical application of nanotechnology is drug delivery. Nanotechnology allows drugs to break through chemical, anatomical, and physiological barriers to reach diseased tissues, increasing the amount of drug accumulation at focal sites and reducing damage to healthy tissue.For example, carefully designed nanomedicines can penetrate cancerous tissues via vascular leakage points and accumulate at the target location, thereby increasing the precision of targeted cancer therapy.In medical imaging, nanoparticles, due to their tiny size and special chemical properties, can form aggregates in specific tissues and tumor locations, thus enabling easier and more accurate diagnosis and improving treatment outcomes.Nanotechnology can also be applied to biological tissue engineering. Nanomaterials such as graphene, nanotubes, and molybdenum disulfide can be used to make scaffolds to help repair or reshape damaged tissues. Nanostructured scaffolds can mimic the unique micro-environment of tissues, promote cell attachment, reproduction and growth, and induce normal cell functions and tissue growth.VI. Nanotechnology risk alertNew technology is like a double-edged sword, bringing benefits and risks, and nanotechnology is no exception. The research report pointed out that while praising its rapid development, people should also be careful of its environmental, health and social impacts.The biggest concern of people at present is the threat of nanoparticles to health, because nanoparticles can easily enter the human body through the lungs or skin. For example, it has been found that metal pollutants in carbon nanotubes and nanoparticles of diesel fuel have adverse effects on health. Workers exposed to nano-pollutants in production operations have a higher health risk.In addition, industrial emissions generated during the manufacturing process of nanomaterials will also pose a risk of environmental pollution. Nanoparticles have high activity and small size, which may adversely affect the ecosystem and pose a threat to the survival of animals and plants.Although nanomedicine has a bright future, it is still unclear whether it is involved in metabolism in the human body and how it is metabolized, so it may also bring unexpected consequences. The long-term effect of nanomedicine is still unclear.FAQ 1. What is nanotechnology used for?Nanotechnology also lowers costs, produces stronger and lighter wind turbines, improves fuel efficiency and, thanks to the thermal insulation of some nanocomponents, can save energy. The properties of some nanomaterials make them ideal for improving early diagnosis and treatment of neurodegenerative diseases or cancer. 2. What exactly is nanotechnology?Nanotechnology is science and engineering at the scale of atoms and molecules. It is the manipulation and use of materials and devices so tiny that nothing can be built any smaller. 3. How is nanotechnology used in everyday life?The average person already encounters nanotechnology in a range of everyday consumer products – nanoparticles of silver are used to deliver antimicrobial properties in hand washes, bandages, and socks, and zinc or titanium nanoparticles are the active UV-protective elements in modern sunscreens. 4. Is Nanotechnology good or bad?Nanoparticles do hold out much environmental promise. The same reactivity that makes them harmful in the body also means they can break down dangerous chemicals in toxic waste – or anywhere, for that matter. And their use in electronics drastically reduces power demand, which could cut greenhouse gases. 5. Is nanotechnology safe for humans?Out of three human studies, only one showed a passage of inhaled nanoparticles into the bloodstream. Materials which by themselves are not very harmful could be toxic if they are inhaled in the form of nanoparticles. The effects of inhaled nanoparticles in the body may include lung inflammation and heart problems. 6. What diseases can nanotechnology cure?Nanomedicine — the application of nanomaterials and devices for addressing medical problems — has demonstrated great potential for enabling improved diagnosis, treatment, and monitoring of many serious illnesses, including cancer, cardiovascular and neurological disorders, HIV/AIDS, and diabetes, as well as many types ...7. What is nanotechnology and why is it important?Why is nanotechnology important? Nanotechnology improves existing industrial processes, materials and applications by scaling them down to the nanoscale in order to ultimately fully exploit the unique quantum and surface phenomena that matter exhibits at the nanoscale. 8. What is so special about nanotechnology?Nanotechnology is not simply working at ever smaller dimensions; rather, working at the nanoscale enables scientists to utilize the unique physical, chemical, mechanical, and optical properties of materials that naturally occur at that scale.9. What are the advantages and disadvantages of nanotechnology?Nanotechnology offers the potential for new and faster kinds of computers, more efficient power sources and life-saving medical treatments. Potential disadvantages include economic disruption and possible threats to security, privacy, health and the environment.10. Why Is nanotechnology dangerous?Nanoparticles are likely to be dangerous for three main reasons: Nanoparticles may damage the lungs. ... Nanoparticles can get into the body through the skin, lungs and digestive system. This may help create 'free radicals' which can cause cell damage and damage to the DNA.

RFID is the abbreviation of Radio Frequency Identification.Its principle is the contactless data communication between the reader and the tag to achieve the purpose of identifying the target. RFID has a wide range of applications, typical applications include animal chip, car chip immobilizer, access control, parking control, production line automation, and material management.What is RFID? How RFID works? RFID Explained in DetailCatalogI Overview of RFIDII Working principle of RFIDIII How RFID system is composed?3.1 About the reader3.2 About electronic tagsIV Features4.1 Applicability4.2 High efficiency4.3 Uniqueness4.4 SimplicityFAQI Overview of RFIDRadio frequency identification, or radio frequency identification technology, is a type of automatic identification technology that uses wireless radio frequency for non-contact two-way data communication. It uses radio frequency to read and write recording media (electronic tags or radio frequency cards) to achieve the purpose of identification and data exchange. It is considered to be one of the most promising information technologies in the 21st century.Radio frequency identification technology uses radio waves without contact with fast information exchange and storage technology, combines wireless communication with data access technology, and then connects to the database system to achieve non-contact two-way communication. In this way, the purpose of identification is achieved, and it can be used for data exchange, connecting an extremely complex system in series.In the identification system, the reading and writing and communication of electronic tags are realized through electromagnetic waves. According to the communication distance, it can be divided into near-field and far-field. For this reason, the data exchange mode between the read/write device and the electronic tag is correspondingly divided into load modulation and backscatter modulation.  II Working principle of RFIDThe basic working principle of RFID technology is not complicated: After the tag enters the reader, it receives the radio frequency signal from the reader, and uses the energy obtained by the induced current to send out the product information stored in the chip (Passive Tag, passive tag or passive tag). ), or the tag actively sends a signal of a certain frequency (Active Tag, active tag or active tag). After the reader reads and decodes the information, it is sent to the central information system for relevant data processing.A complete RFID system is composed of three parts: a reader, an electronic tag, a so-called transponder, and an application software system. Its working principle is that the reader emits radio wave energy of a specific frequency to drive the circuit to send out the internal data. At this time, the Reader receives the interpretation data in order and sends it to the application program for corresponding processing.From the perspective of the communication and energy sensing methods between the RFID card reader and the electronic tag, it can be roughly divided into two types: inductive coupling and backscatter coupling. Generally, low-frequency RFID mostly adopts the first method, and high-frequency RFID mostly adopts the second method.The reader can be a read or read/write device depending on the structure and technology used, and it is the information control and processing center of the RFID system. The reader usually consists of a coupling module, a transceiver module, a control module and an interface unit.The reader and the tag generally adopt a half-duplex communication mode for information exchange, and the reader provides energy and timing to the passive tag through coupling. In practical applications, management functions such as the collection, processing and remote transmission of object identification information can be further realized through Ethernet or WLAN. III How RFID system is composed?The complete RFID system consists of three parts: Reader, Tag and data management system. 3.1 About the readerThe reader is a device that reads the information in the tag or writes the information that the tag needs to store into the tag. Depending on the structure and technology used, the reader can be a read/write device, which is the information control and processing center of the RFID system. When the RFID system is working, the reader sends radio frequency energy in an area to form an electromagnetic field, and the size of the area depends on the transmit power.The tag in the coverage area of the reader is triggered to send the data stored in it, or modify the data stored in it according to the instructions of the reader, and can communicate with the computer network through the interface. The basic composition of the reader usually includes: transceiver antenna, frequency generator, phase-locked loop, modulation circuit, microprocessor, memory, demodulation circuit and peripheral interface composition.(1) Transceiver antenna: Send radio frequency signals to the tag, and receive the response signal and tag information returned by the tag.(2) Frequency generator: Generates the operating frequency of the system.(3) Phase-locked loop: Generate the required carrier signal.(4) Modulation circuit: Load the signal sent to the tag to the carrier wave and send it out by the radio frequency circuit.(5) Microprocessor: Generates the signal to be sent to the label, decodes the signal returned by the label, and sends the decoded data back to the application program. If it is an encrypted system, a decryption operation is also required.(6) Memory: store user programs and data.(7) Demodulation circuit: demodulate the signal returned by the tag and deliver it to the microprocessor for processing.(8) Peripheral interface: to communicate with the computer.3.2 About electronic tagsThe electronic tag consists of a transceiver antenna, AC/DC circuit, demodulation circuit, logic control circuit, memory and modulation circuit.(1) Transceiver antenna: Receive the signal from the reader and send the required data back to the reader.(2) AC/DC circuit: Utilize the electromagnetic field energy emitted by the reader, output by the voltage regulator circuit to provide a stable power supply for other circuits.(3) Demodulation circuit: Remove the carrier from the received signal and demodulate the original signal.(4) Logic control circuit: decode the signal from the reader, and send back the signal according to the requirements of the reader.(5) Memory: As a location for system operation and storage of identification data.(6) Modulation circuit: The data sent by the logic control circuit is loaded to the antenna and sent to the reader after the modulation circuit.IV FeaturesGenerally speaking, the radio frequency identification technology has the following characteristics.  4.1 ApplicabilityRFID technology relies on electromagnetic waves and does not require physical contact between the connecting parties. This makes it possible to establish connections without regard to dust, fog, plastic, paper, wood and various obstacles, and to complete communications directly. 4.2 High efficiencyRFID system read and write speed is extremely fast, a typical RFID transmission process is usually less than 100 milliseconds. RFID readers in the high frequency band can even identify and read the contents of multiple tags simultaneously, greatly improving the efficiency of information transmission.  4.3 Uniquenesseach RFID tag is unique, through the RFID tag and product one-to-one correspondence, you can clearly track the subsequent circulation of each product. 4.4 SimplicityRFID tag structure is simple, high recognition rate, the required reading equipment is simple. Especially with the gradual popularization of NFC technology on smart phones, each user's cell phone will become the simplest RFID reader.FAQ 1. What is RFID used for?Radio Frequency Identification (RFID) is the wireless non-contact use of radio frequency waves to transfer data. Tagging items with RFID tags allows users to automatically and uniquely identify and track inventory and assets.2. What is RFID and how it works?RFID is a method of data collection that involves automatically identifying objects through low-power radio waves. Data is sent and received with a system consisting of RFID tags, an antenna, an RFID reader, and a transceiver.3. What RFID means?Radio Frequency Identification (RFID) refers to a wireless system comprised of two components: tags and readers. The reader is a device that has one or more antennas that emit radio waves and receive signals back from the RFID tag.4. Is RFID harmful to human?It is a non-ionizing type of radiation, but some researches show that it could have a negative impact on the human body in a long-term period [11, 12]. So, for the safety reasons, manufacturers of the RFID systems have limited the range of the RFID antennas used in their systems.5. Is RFID tag and FASTag same?FASTag is a device that employs Radio Frequency Identification (RFID) technology for making toll payments directly while the vehicle is in motion. FASTag (RFID Tag) is affixed on the windscreen of the vehicle and enables a customer to make the toll payments directly from the account which is linked to FASTag.6.What is RFID and its advantages?RFID technology automates data collection and vastly reduces human effort and error. RFID supports tag reading with no line-of-sight or item-by-item scans required. RFID readers can read multiple RFID tags simultaneously, offering increases in efficiency.7. Why is RFID bad?Some negative effects are that its deadly, if RFID tags combine with static electricity you can die. Another negative effect is that the government is slowly taking away surviving resources and giving ultimatums, such as if you don't get the RFID tracking chip your public assistance will be terminated.8.What are the disadvantages of RFID?a. Materials like metal & liquid can impact signal.b. Sometimes not as accurate or reliable as barcode scanners.c. Cost – RFID readers can be 10x more expensive than barcode readers.d. Implementation can be difficult & time consuming.9.How do I charge my RFID FASTag?In order to recharge your FASTag sticker, just hit the Add Money option in your Paytm app. FASTag will automatically reserve some amount from your wallet, which can be used at toll plazas later. Do note that FASTag can be used only after 20 mins of adding money to the Paytm Wallet.10. Can I use existing RFID for FASTag?If a vehicle already has an RFID tag, it might already be activated. When you buy the vehicle, RFID tag payment was also done. It might also have a minimum balance of INR 100 or 200 as is required by the bank. You can recharge it with your Customer ID or Wallet ID of FASTag.11. How does RFID work without power?Passive RFID tags have no power of their own and are powered by the radio frequency energy transmitted from RFID readers/antennas. The signal sent by the reader and antenna is used to power on the tag and reflect the energy back to the reader.12. What are the types of RFID tags?RFID tags can be grouped into three categories based on the range of frequencies they use to communicate data: low frequency (LF), high frequency (HF) and ultra-high frequency (UHF). Generally speaking, the lower the frequency of the RFID system, the shorter the read range and slower the data read rate.13.How do I know if I have an RFID chip?The best way to check for an implant would be to have an X-ray performed. RFID transponders have metal antennas that would show up in an X-ray. You could also look for a scar on the skin. Because the needle used to inject the transponder under the skin would be quite large, it would leave a small but noticeable scar.14. Does RFID require power?Active RFID tags possess their own power source – an internal battery that enables them to have extremely long read ranges as well as large memory banks. Typically, active RFID tags are powered by a battery that will last between 3 - 5 years, but when the battery fails, the active tag will need to be replaced.15. What is the difference between a QR code and RFID?QR codes must always be “read-only”, whereas RFID tags can be “read-write”, depending on the radio frequency that's being used. ... So, not only are RFID tags futuristic and have more uses than QR tags, they also have many more applications. The read range is far superior for an RFID tag. 

FPGA (Field-Programmable Gate Array), it is the product of further development on the basis of PAL, GAL, CPLD and other programmable devices. It appears as a kind of semi-custom circuit in the field of application specific integrated circuit (ASIC). It not only solves the shortage of custom circuit, but also overcomes the shortcoming of limited number of gates in the original programmable devices.What is an FPGA, and how does it compare to a microcontroller?CatalogI. What is FPGA?II. Principles of FPGAs III. FPGA Pros & ConsIV. FPGA Chip StructureV. FPGA FeaturesFAQI. What is FPGA?FPGA (Field Programmable Gate Array) is a product of further development on the basis of programmable devices such as PAL and GAL. It emerged as a semi-custom circuit in the field of application-specific integrated circuits (ASIC), which not only solves the deficiencies of custom circuits, but also overcomes the shortcomings of the limited number of gate circuits of the original programmable devices.II. Principles of FPGAs FPGA adopts the concept of Logic Cell Array (LCA), which consists of Configurable Logic Block (CLB), Input Output Block (IOB) and Internal Interconnect. Three parts. FPGAs are programmable devices with a different structure than traditional logic circuits and gate arrays (such as PAL, GAL and CPLD devices). The logic of the FPGA is implemented by loading programmed data into the internal static memory cell, and the values stored in the memory cell determine the logic function of the logic cell and the connection between the modules or between the modules and the I/O. The value stored in the memory cell determines the logical function of the logic unit and the way the modules are linked to each other or to the I/O, and ultimately determines the functions that the FPGA can achieve.III. FPGA Pros & Cons - The Pros of FPGAs:(1) FPGAs consist of hardware resources such as logic cells, RAM, multipliers, etc. By organizing these hardware resources rationally, hardware circuits such as multipliers, registers, address generators, etc. can be implemented.(2) FPGAs can be designed by using block diagrams or Verilog HDL, from simple gate circuits to FIR or FFT circuits.(3) FPGAs can be infinitely reprogrammed, loading a new design solution in a few hundred milliseconds, reducing hardware overhead with reconfiguration.(4) The operating frequency of the FPGA is determined by the FPGA chip as well as the design, and can be modified by modifying the design or replacing it with a faster chip to meet certain demanding requirements (of course, the operating frequency is not unlimited and can be increased, but is governed by current IC processes and other factors).  - The Cons of FPGAs:(1) All functions of FPGAs rely on hardware implementation and cannot implement operations such as branching conditional jumping.(2) FPGAs can only implement fixed-point operations.To conclude: FPGAs rely on hardware to implement all functions and can be compared to dedicated chips in terms of speed, but there is a big gap in design flexibility compared to general purpose processors.IV. FPGA Chip StructureMainstream FPGA is still based on look up table technology, has far exceeded the basic performance of previous versions, and integrates common features (such as RAM, clock management and DSP). FPGA chips have seven main parts: programmable input/ output unit, basic programmable logic unit, complete clock management, embedded block RAM, rich wiring resources, embedded bottom functional unit and embedded special hardware module.The functions of FPGA chip structure are as follows:1. Programmable Input and Output BlockThe programmable input/ output block is referred to as I/ O port. It is the interface part between the chip and the external circuit, which can drive and match the input/ output signals under different electrical characteristics. I/ O in FPGA is classified by group, and each group can support different I/ O standards independently. With the flexible configuration of the software, different electrical standards and I/ O physical characteristics can be met, the drive current can be adjusted, and the frequency of I/ O port of the and pull-up resistor and pull-down resistor can be changed, so that the frequency of the I/ O port can be higher and higher. Some high-end FPGA can support data rate up to 2Gbps through DDR register.Fig 1. IOB Internal Structure DiagramThe external input signal can be read into the FPGA through the memory cell of the IOB module, or directly written into the inside of the FPGA. When the external input signal passes through the memory cell of the IOB module read into the inside of the FPGA, the requirement of hold time  can be reduced, which usually the windows default is 0.In order to facilitate management and adapt to a variety of electrical standards, FPGA's IOB is divided into several banks, each bank interface standard is determined by its interface voltage VCCO, in addition, a bank can only have one VCCO, but each bank VCCO can be different. Only ports with the same electrical standard can be connected together, and the same VCCO voltage is the basic requirement of the interface standard.2. Configurable Logic Block (CLB)CLB is the basic logical unit within the FPGA. The actual number and characteristics of CLBs vary depending on the device, but each CLB contains a configurable switch matrix that consists of 4 or 6 inputs, some lectotype circuits (multiplexers, etc.) and flip-flops. The switch matrix is highly flexible and can be configured to work with combinational logic, shift registers, or RAM. In Xilinx's FPGA device, the CLB consists of multiple (usually 4 or 2) identical Slices and additional logic. Each CLB module be used to realize combinational logic and sequential logic, and it can also be configured as distributed RAM and distributed ROM.Fig 2. CLB Structure DiagramSlice is a basic logical unit defined by Xilinx. A Slice consists of two 4-input functions, carry logic, arithmetic logic, storage logic and function multiplexer. Arithmetic logic includes a  XORG and a MULTAND. XORG enables a Slice to implement the full operation of 2bit, and MULTAND improves the efficiency of multipliers. Carry logic consists of a dedicated carry signal and a function multiplexer for fast arithmetic addition and subtraction operations; 4-input functions generator is used to implement the 4-input LUT, distributed RAM or 16-bit shift register. Carry logic includes two fast carry chains to improve the processing speed of the CLB module.Fig 3. Inputting Slice Structure Diagram3. Digital Clock Management (DCM)Most of the industry's FPGA offer digital clock management. FPGA offers digital clock management and phase loop locking. Phase loop locking can provide accurate clock synthesis, reduce jitter and achieve filtering.4. Block Random Access Memory (BRAM)Most FPGAs have embedded block RAM, which greatly extends the applications and flexibility of the FPGA. The block RAM may be configured as a single-port RAM, a dual-port RAM, a content address memory (CAM), and a common storage structure such as a FIFO. CAM memory has a comparison logic in each of its internal memory cells, the data written into the CAM will be compared with each of the data in the interior, and the address of all data that is the same as the port data, so that there is a wide range of address switches in the route application. In addition to the block RAM, the LUT in the FPGA can be flexibly configured as a RAM, a ROM, and a FIFO. In practical application, that number of block RAM in the internal block of the chip is also an important factor in the chip selection.The capacity of the monolithic RAM is 18k bits, that is, the bit width is 18 bits and the depth is 1024. It can change the bit width and depth according to the need, but two principles must be satisfied: firstly, the modified capacity (bit width depth) cannot be greater than 18k bits; Second, the maximum bit width cannot exceed 36 bits. Of course, it is possible to concatenate multiple blocks of RAM to form a larger RAM, which is limited only by the number of RAM blocks in the chip and is no longer constrained by the above two principles.5. Wiring SourceAll the parts are connected with wiring resources in the FPGA, and the length and process of the connection determine the driving ability and the transmission speed of the signal on the wire. There are abundant wiring resources in the FPGA chip, according to the process and length, width and distribution position, which are divided into 4 different categories. First is the global routing resource, which is used for the internal global clock and the global reset/ position routing. Second is the long line resource, which is used to complete the wiring of the high-speed signal and the second global clock signal between chip banks. Third is short-line resources, which are used to perform logical interconnection and cabling between basic logical units. Fourth is a distributed wiring resource, which is used as control signal lines for a proprietary clock or a reset.In practice, the designer does not need to select the routing resources directly, and the layout scheduler can automatically select the better routing resources according to the topology of the input logical grid table and constraint conditions to connect each module unit. In essence, the use of routing resource types has a close and direct relationship with the results of the design.6. Underlying Built-in Function The underlying built-in function mainly refers to a DLL (Delay Locked Loop), a PLL (Phase Locked Loop), a DSP, and a CPU, which belong to core softcore. The more and more built-in functional units make the single-chip FPGA a system-level design tool, so that it has the capability of joint design of hardware and software, and gradually turn to the SOC platform.DLL and PLL have similar functions, such as high-precision clock and low jitter frequency doubling and frequency division, duty cycle adjustment and phase shift, etc. Xilinx integrated the DLL, Altera made the PLL, Lattice combined both two, which can be easily managed and configured through IP core-generated tools on Lattice's new chip. Fig 4. Typical DLL module schematics7. Special Built-in Hard CoreThe embedded special hard core is relative to the soft core embedded in the bottom, which means that the hard core with strong processing ability of FPGA is equivalent to the ASIC. To improve FPGA performance, chip manufacturers integrate some dedicated hard cores on the chip. For example, to improve the multiplication speed of FPGA, special multipliers are integrated in the mainstream FPGA, and in order to match the communication bus and interface standard, a lot of high-end FPGA are integrated SERDES, which can achieve the receiving and dispatching speed of  Gbps. V. FPGA Features1) The ASIC circuit is designed by adopting the FPGA, and the user does not need to put the chip into production, so that a shared chip can be obtained.2) FPGA can be used as a trial sample of other fully customized or semi-custom ASIC circuits.3) There are rich flip-flops and I/ O pins within the FPGA.4) FPGA is one of the devices with the shortest design cycle, the lowest development cost and the least risk among ASIC circuits.5) FPGA adopts high-speed CMOS process, low power consumption, and can be compatible with CMOS and TTL.It can be said that FPGA chip is one of the best choices for small batch system to improve system integration and reliability.The working state of FPGA is set by the program stored in the on-chip RAM, so it is necessary to program the on-chip RAM when working. Users can use different programming methods according to different configuration modes.When the power is on, the FPGA chip reads the data from the EPROM into the on-chip programming RAM. After the configuration is completed, the FPGA enters the working state. After power off, FPGA internal logic disappears. Therefore, FPGA can be programmed repeatedly. And the programming of FPGA does not require a special programmer, a general-purpose EPROM or PROM programmer can meet the requirement. When you need to modify the FPGA functionality, just replace a piece of EPROM. In this way, the same piece of FPGA, with different programming data, can produce different circuit functions. Therefore, the use of FPGA is very flexible.FAQ 1. What is FPGA and why it is used?FPGA Basics: Architecture, Applications and Uses. The field-programmable gate array (FPGA) is an integrated circuit that consists of internal hardware blocks with user-programmable interconnects to customize operation for a specific application.2. Is FPGA faster than CPU?They also found that using custom FPGAs to implement the Rowhammer exploit would cause far more of the "bit flips" that they wanted to see. A FPGA can hit the data cell faster and more often than a CPU can do it meaning the FPGA causes more results to occur during an attack. It all goes faster when an FPGA is used.3. Are FPGAs dead?Yes, it's a dead end. If you enjoy creating hardware, RTL design targeting FPGAs is still a good choice (although there is a huge amount of effort here to make it more like creating software than hardware).4. What are FPGAs good for?FPGAs are particularly useful for prototyping application-specific integrated circuits (ASICs) or processors. An FPGA can be reprogrammed until the ASIC or processor design is final and bug-free and the actual manufacturing of the final ASIC begins. Intel itself uses FPGAs to prototype new chips.5. Is FPGA a microprocessor?Microprocessors are more complex than FPGAs. Microprocessors have fixed instructions while FPGAs don't. FPGAs and microprocessors are often mixed into a single package.6. What are the advantages of FPGA?FPGA advantages:Long-term availability.Updating and adaptation at the customer.Very short time-to-market.Fast and efficient systems.Acceleration of software.Real-time applications.Massively parallel data processing.7. Why is FPGA slow?FPGAs tend to get faster in max speed, but the limit actually has to do with process variation affecting static timing. The chips have to have a soultion that works on all of them. So you lose performance of the device to make sure any device will work with it. And as your design gets bigger it runs slower.8. What are the disadvantages of FPGA?Drawbacks or disadvantages of FPGA:The programming is not as simple as C programming used in processor based hardware. Moreover engineers need to learn use of simulation tools. ➨The power consumption is more and programmers do not have any control on power optimization in FPGA. No such issues in ASIC.9. Can FPGA replace CPU?There will always be a need for a general purpose CPU to run most things, and while you can implement a CPU on an FPGA, that gives you the worst of both worlds - no improvement from specialised hardware design, and you still need to pay the “FPGA tax”. So no, FPGAs will never replace CPUs.10. Why use an FPGA vs microcontroller?A FPGA can be used if the design requires complex logic and requires high processing ability and if the cost is comparable to the performance achieved. In case of a design that requires limited hardware, and is set to perform only some specific functions, then Microcontroller is preferred.

What is a resistor? In short, resistors are electronic components which have a specific, never-changing electrical resistance. The resistor's resistance limits the flow of electrons through a circuit. So in this article today, we will have a detailed discussion on resistors, which will present you as much as information about resistor as possible.I What is a Resistor?1.1 Brief IntroductionResistors are passive electrical components that limit electric current. This video explains in an easy way the most basic background to help you understand resistors and use them.A resistor refers to a two-terminal electronic element made of resistor material with a certain structure that can limit the current passing through the circuit. It is the most widely used component in electronic circuits, which usually form different series according to its power and resistance values. Its function in circuits is to regulate and stabilize current and voltage, that is,  used as shunt and voltage divider, or circuit matching load. According to the circuit requirements, it can also be used for negative feedback or positive feedback of amplifying circuit, voltage-current conversion, voltage or current protecting element when existing input overload. With the capacitor, it can form an RC circuit, which can be used as oscillation, filter, bypass, differential, Integral and time constant elements, etc. Those whose resistance values cannot be changed are called fixed resistors, and those with variable resistance values are called potentiometers or variable resistors. Some special resistors, such as thermistors, varistors, and sensitive elements, have a nonlinear relationship between voltage and current.1.2 Resistor and ResistanceThe resistor is a current limiting element in daily life. Resistance is a physical quantity describing the conductivity of a conductor, represented by R. Resistance is defined by the ratio of the voltage U at the two ends of the conductor and the current I passing through the conductor, that is, R=V/I. When the resistor is connected to the circuit, the resistor's resistance is fixed by two pins, which can limit the current to flow through the branch of the resistor. The resistance that cannot be changed is called a fixed resistor. In addition, a variable resistance is called a potentiometer or a variable resistor. The ideal resistor is linear, that is, the instantaneous current of the resistor is positive to the applied instantaneous voltage, for example, the variable-voltage resistor is used as a voltage divider. On a bare resistor, there are one or two removable metal contacts, and the contact position determines the resistance between any end of the resistor and the contact.  The terminal voltage and current have a definite function relation, and the two-terminal device which embodies the conversion of electric energy into other forms, represented by the letter R, and its unit is Ω. Devices such as light bulbs, heating wires, resistors, and so on can be expressed as resistor elements.The resistance value of the resistor is generally related to temperature, material, component length, and cross-section area. The physical quantity of measuring resistance affected by the temperature is the temperature coefficient, which is defined as the percentage of resistance value changing when the temperature rises 1℃. The main physical characteristic of resistors is transforming the electricity into heat energy, also the resistor can be said to be an energy dissipation element because the internal energy will be generated when current flows through it. Resistors usually act as a divider and shunt in a circuit. And for signals, both AC and DC signals can pass through resistors.In physics, resistance is a figure to indicate the magnitude of a conductor's hindrance to current. The greater the resistance of a conductor, the greater the resistance of the conductor to the current. Generally, different conductors have different resistances, in other words, resistance is a characteristic of the conductor itself. The resistance element is a kind of energy dissipation element which hinders the current. The stuff under the action of matter called resistive substance because of its blocking effect on the current. The resistor will lead to the change of the electron flux. When the voltage at both ends of the conductor is fixed, the larger the resistance, the smaller the current passing through, on the other hand, the smaller the resistance, the greater the current passing through. 1.3 Resistor BasicsThe resistor consists of three parts of a resistor body, a framework, and a lead-out end (the resistor body of the solid-core resistor is integrated with the framework), and the resistor body plays an important part in this electronic component. For a resistor body with a uniform cross-section, the resistance value is calculated by the following formula: ρ is the electrical resistivity (ohm-cm), L is the length (cm) of the resistor, and A is the cross-sectional area of the resistor (square centimeter).R=ρ× L/AThe thickness of the thin film resistor is very small and difficult to measure accurately, and ρ varies with the thickness values, so the constant related to the film material is regarded as the film resistance. In fact, it is the resistance of the square film, so it is also known as the square resistance. For homogeneous films, W is the width of the film (cm), in general, Rs should be in a limited range because large Rs will affect the stability of resistor performance. Therefore the cylindrical resistor is notched and the planar resistor uses the etching method of a detour to extend the range of resistance and to fine-tune the resistance.R=Rs×L/WThe volt-ampere characteristic is a graph that represents the relationship between the voltage and the current of the resistor terminal. When the voltage-current is proportional (representing a straight line), it is called a linear resistor, otherwise referred to as a non-linear resistor.The vertical coordinates of this diagram are current I and the transverse coordinates are voltage U. This graph is also called the current-voltage curve, more often is referred to as the volt-ampere characteristics curve. As we can see, the blue curve is a straight line passing through the origin, and its resistance does not change with the change of voltage and current, in fact, elements that satisfy this volt-ampere characteristic curve are called linear elements. On the other hand, for the red curve, we can see that it is a curve, its resistance value changes with the change of voltage and current.The main parameters used to characterize the resistance have nominal resistance, allowable deviation, rated power, load characteristic, resistor temperature coefficient, and so on.1.4 Resistor Operation TheoryOhm's lawThe behavior of an ideal resistor is dictated by the relationship specified by Ohm's law:V=I ∙ ROhm's law states that the voltage (V) across a resistor is proportional to the current (I), where the constant of proportionality is the resistance (R). For example, if a 300-ohm resistor is attached across the terminals of a 12-volt battery, then a current of 12/300 = 0.04 amperes flows through that resistor.Practical resistors also have some inductance and capacitance which affect the relation between voltage and current in alternating current circuits.In addition, linear or ohmic resistance meets Ohm's law, but nonlinear resistance does not satisfy Ohm's law.The nominal resistance is the design resistance of the sign on the resistor with a digital or color code. The units are Ω, KΩ, and MΩ. Resistance values are written according to standardized priority series, which correspond to allowable deviations.The electrical resistance of a resistor is measured in ohms. The symbol for an ohm is the greek capital-omega: Ω. The ohm (symbol: Ω) is the SI unit of electrical resistance, named after Georg Simon Ohm. An ohm is equivalent to a volt per ampere. Since resistors are specified and manufactured over a very large range of values, the derived units of milliohm (1 mΩ = 10−3 Ω), kilohm (1 kΩ = 103 Ω), and megohm (1 MΩ = 106 Ω) are also in common usage. For example, a 4,700Ω resistor is equivalent to a 4.7kΩ resistor, and a 5,600,000Ω resistor can be written as 5,600kΩ or (more commonly as) 5.6MΩ. 1.5 Resistor Electronic SymbolsNotation1Ω= 1 Ohms1 KΩ= 1 Kilo Ohms1 MΩ= 1 Mega Ohms1 GΩ= 1 Giga OhmsWhen the value can be expressed without a prefix (that is, multiplicator 1), an "R" is used instead of the decimal separator. For example, 1R3 indicates 1.3Ω, and 15R indicates 15Ω.Marking method for Resistance and Tolerance of Resistors：① Direct Scaling MethodThe resistance and error of the resistor are directly printed on the resistor by numbers and letters (no error is indicated as the tolerance ±20%). There are also manufacturers who use customary marking methods, such as:3Ω3Ⅰis represent the resistance 3.3Ω, tolerance is ±5%1 K 8 represents the resistance 1.8 KΩ, tolerance is ±20%5 M 1Ⅱis represent the resistance 5.1 MΩ, tolerance is ±10% ② Resistor Color Bands/CodesThis Physics video tutorial is explaining the fundamentals of color code for four colour bands in a carbon resistor.The color bands are coated on the resistor to indicate the nominal value of the resistor and the allowable tolerance. The corresponding values of various colors and the recognition rules of the color bands/codes of the reading principle of the fixed resistor are shown in the following figure.Four-band ResistorsIn the standard four-band resistors, the first two bands indicate the two most significant digits of the resistor’s value. The third band is a weight value, which multiplies the two significant digits by a power of ten.The final band indicates the tolerance of the resistor. The tolerance explains how much more or less the actual resistance of the resistor can be compared to what its nominal value is. No resistor is made to perfection, and different manufacturing processes will result in better or worse tolerances. For example, a 1kΩ resistor with 5% tolerance could actually be anywhere between 0.95kΩ and 1.05kΩ.Example: red-orange black gold=23*10^0=23Ω(±5%)Five-band and six-band ResistorsFive band resistors have a third significant digit band between the first two bands and the multiplier band. Five band resistors also have a wider range of tolerances available.Six band resistors are basically five band resistors with an additional band at the end that indicates the temperature coefficient. This indicates the expected change in resistor value as the temperature changes in degrees Celsius. Generally, these temperature coefficient values are extremely small, in the ppm range.Example: red blue green black brown=265*10^0=265Ω(±1%)ToleranceThe maximum tolerance between the actual resistance and the nominal resistance, represented by percentages. Commonly used are ±5%, ±10%, ±20%, precision is less than ±1%, high precision up to 0.001%. The accuracy is determined by both the tolerance and the irreversible resistance.Power RatingMaximum power dissipation allowed for continuous operation of resistors at rated temperature (maximum ambient temperature) tR. And the maximum operating voltage is also specified for each resistor, that is, the maximum operating voltage cannot be exceeded even if the resistance value is high.Identification of rated Power of ResistorsThe rated power of a resistor refers to the maximum power that a resistor is allowed to consume in a long-term continuous operation in a DC or AC circuit. There are two marking methods: the resistance above 2W is directly printed on the resistor body, and the resistance below 2W is represented by its own volume. When the resistance power is expressed on the circuit diagram, the following symbols are used: 1) Load CharacteristicWhen the working temperature is lower than tR, the resistor can not exceed its rated power, and the load power must be reduced when it exceeds tR. Each resistor has its own specified load characteristic. In addition, the load is allowed to be reduced accordingly at low pressure. Under pulse load, the average power of the pulse is much lower than the rated power, the load is according to the practical situation.2) Resistance Temperature CoefficientThe average relative variation of the resistance value at each change of 1℃ is expressed in terms of ppm/ ℃ within a specified range of ambient temperature. In addition to the above parameters, there are other technical indicators, such as nonlinearity (the extent to which the characteristics of the current and the applied voltage deviate from the linear relationship), the voltage coefficient (the relative rate of change of the voltage at which the voltage is applied, the relative rate of change of the volt resistance), current noise (the ratio of the effective value of the noise potential generated by the current flow in the resistor to the measured voltage, expressed by the current noise index), the high-frequency characteristic (due to the effect of the distributed capacitance and the distributed inductance in the resistor; a curve in which the resistance value decreases as the operating frequency increases; long-term stability (such as irreversible changes in resistance values affected by environmental conditions during long term use or storage).II Resistor CharacteristicsDependent on the application, the electrical engineer specifies different properties of the resistor. The primary purpose is to limit the flow of electrical current; therefore the key parameter is the resistance value. The manufacturing accuracy of this value is indicated with the resistor tolerance in percentage. Many other parameters that affect the resistance value can be specified, such as long-term stability or the temperature coefficient. The temperature coefficient, usually specified in high precision applications, is determined by the resistive material as well as the mechanical design.In high-frequency circuits, such as in radio electronics, the capacitance and inductance can lead to undesired effects. Foil resistors generally have a low parasitic reactance, while wire-wound resistors are amongst the worst. For accurate applications such as audio amplifiers, the electric noise must be as low as possible. This is often specified as microvolts noise per volt of applied voltage, for a 1 MHz bandwidth. For high-power applications, the power rating is important. This specifies the maximum operating power the component can handle without altering the properties or damage. The power rating is usually specified in free air at room temperature. Higher power ratings require a larger size and may even require heat sinks. Many other characteristics can play a role in the design specification. Examples are the maximum voltage or the pulse stability. In situations where high voltage surges could occur this is an important characteristic.Resistors in series and parallel ConnectionIn electronic circuits, resistors are very often connected in series or in parallel. A circuit designer might for example combine several resistors with standard values (E-series) to reach a specific resistance value. For series connection, the current through each resistor is the same and the equivalent resistance is equal to the sum of the individual resistors. For parallel connection, the voltage through each resistor is the same, and the inverse of the equivalent resistor value is equal to the sum of the inverse values for all parallel resistors. In the articles resistors in parallel and series, a detailed description of calculation examples is given. To solve even more complex networks, Kirchhoff’s circuit laws may be used.The Total resistance of resistors connected in series is the sum of each single individual resistance value.The total resistance of resistors connected in parallel is the reciprocal of the sum of the reciprocals of the individual resistors.As a special case of this equation: if you have just two resistors in parallel, their total resistance can be calculated with this slightly-less-inverted equation:Termination and MountingResistors will come in one of two termination types: through-hole or surface-mount. These types of resistors are usually abbreviated as either PTH (plated through-hole) or SMD/SMT (surface-mount technology or device).Through-hole resistors come with long, pliable leads which can be stuck into a breadboard or hand-soldered into a prototyping board or printed circuit board (PCB). These resistors are usually more useful in breadboarding, prototyping, or in any case where you’d rather not solder tiny, little 0.6mm-long SMD resistors. The long leads usually require trimming, and these resistors are bound to take up much more space than their surface-mount counterparts.The most common through-hole resistors come in an axial package. The size of an axial resistor is relative to its power rating. A common 1/2W resistor measures about 9.2mm across, while a smaller 1/4W resistor is about 6.3mm long.Surface-mount resistors are usually tiny black rectangles, terminated on either side with even smaller, shiny, silver, conductive edges. These resistors are intended to sit on top of PCBs, where they’re soldered onto mating landing pads. Because these resistors are so small, they’re usually set into place by a robot and sent through an oven where solder melts and holds them in place.III Resistor TypesMost types of the resistor are linear devices that produce a voltage drop across themselves when an electrical current flows through them because they obey Ohm’s Law, and different values of resistance produce different values of current or voltage. This can be very useful in Electronic circuits by controlling or reducing either the current flow or voltage produced across them we can produce a voltage-to-current and current-to-voltage converter.Resistors come in a variety of shapes and sizes. They might be through-hole or surface-mount. They might be a standard, static resistor, a pack of resistors, or a special variable resistor. The different types of resistors are discussed in the following section.1. Classified by Volt-ampere Characteristic*Linear resistors*Non-linear resistorsFor most conductors, at a certain temperature, the resistance is almost unchanged and is a certain value, the resistors having this kind of resistance is called a linear resistor. The resistors of some materials vary obviously with the current (or voltage) change, and the volt-ampere characteristic of them is a curve, which is called a nonlinear resistor. Under a given voltage (or current), the ratio of voltage to current is the static resistance at the working point, and the slope on the voltage-ampere characteristic curve is dynamic resistance. The expression of nonlinear resistance characteristics is complicated, but these nonlinear relations are widely used in electronic circuits.2. Classified by Material1) Wirewound resistor is made of resistive wires, wound high resistance alloy wires on an insulating skeleton, and coated with a heat-resistant glaze insulating layer or insulating paint. The wire-wound resistor has a low-temperature coefficient, high resistance accuracy, good stability, sound heat resistance, and corrosion resistance. It is mainly used for precise and high power resistance. The shortcoming is that the high-frequency performance is poor and the time constant is large.  ApplicationsIt has high securityAccurate measurement and balance current control is required.2) The carbon composition resistor is made from the mixer of granulated or graphite, an insulation filter, and a resin binder. The actual resistance of the resistor is determined by the ratio of the insulation material. The shape of the insulating binder is in the shape of roads and there are two metal caps at both the end of the roads. At both ends of the resistor, it has two wire conductors for easy connectivity in the circuit design. There are different colors that are printed on the resistor to find the value of it and the road is covered with the plastic coat.   ApplicationsThe composition resistor is used in the high energy pulses.·It has a relatively small size.·High voltage power supplies·Welding·High power3) A carbon film resistor is plated with a carbon layer on the porcelain tube, and the crystalline carbon is deposited on the ceramic rod framework. Furthermore, the temperature coefficient is from -100 to -900 ppm/°C. The carbon film resistor has the advantages of low cost, stable performance, wide resistance range, low-temperature coefficient, and low voltage coefficient, and is the most widely used resistor.  ApplicationsThe carbon film resistors are available in High plus stability.4) A metal film resistor is coated with a layer of metal on the ceramic tube, and the alloy material is plated on the surface of the ceramic rod skeleton by vacuum evaporation.Metal film resistor is more accurate than carbon film resistor, other advantages such as good stability, small noise, low-temperature coefficient. It is widely used in instrumentation and communication equipment.5) Metal oxide film resistors are coated with tin oxide on the ceramic tube, and a layer of metal oxide is deposited on the insulating rod. Because its body is an oxide, so it has high temperature stability, heat shock resistance, sound load capacity. According to the purpose, it is divided into universal, precision, high frequency, high voltage, high resistance, and high power type, also it can forms resistors network.IV Special Resistors1) KNP-RF: it also called a fuse resistor, which functions like a resistor and a fuse in the normal condition. When the circuit fails to make the power exceed the rated power, it will be blown as if the fuse is blown and the connection circuit is disconnected. The general resistance of the fuse resistance is small (0.33Ω ~ 10KΩ), and the power is also small. The common types of fuse resistors are RF10 type, RF111-5 fuse resistor symbol type, RRD0910 type, RRD0911 type, etc.2) Sensitive resistor: a resistor whose resistance value is sensitive to certain physical quantities (such as temperature, humidity, light, voltage, mechanical force, gas concentration, etc.). When these quantities change, The resistance value of the sensitive resistors will change with the change of physical quantity, showing different resistance values. According to the sensitivity to different physical quantities, the sensitive resistor can be classified as heat-sensitive, humidity-sensitive, photosensitive, pressure-sensitive, force-sensitive, magnetic sensitive, and gas sensitive. Sensitive resistors are almost made of semiconductor materials, thus they are also known as semiconductor resistors.The resistance of the thermistor varies with the change of temperature, when the temperature rise, this resistor is a negative temperature coefficient (NTC) thermistor. In most cases, the NTC thermistor is widely used, according to its different use, it can be divided into common NTC thermistor, steady-voltage NTC thermistor, thermometric NTC thermistor, and so on. The resistance of the photosensitive resistor changes with the intensity of the incident light. When the incident light is enhanced, the resistance decreases and the resistance increases when the incident light weakens.V How to Select a Suitable Resistor1) There are many types of fixed resistors, what materials and structures should be selected, it is necessary to consider the specific requirements of the application circuit. In high-frequency circuits, non-wire-wound resistors with small distributed inductance and capacitance should be selected,  such as carbon film resistor, metal resistor, and metal oxide film resistor, thin-film resistor, thick film resistor, alloy resistor, corrosion-resistant film resistor, etc. In high gain and small-signal amplifying circuits, low noise resistors should be used, such as metal film resistors, carbon film resistors, and wire-wound resistors, rather than synthetic carbon film resistors and organic solid resistors with high noise.There are different types of the resistor which are in the following:Carbon compositionCarbon PileCarbon filmPrinted carbon resistorThick and thin filmMetal filmMetal oxide filmWire woundFoil resistorAmmeter shuntGrid resistorSpecial veritiesLed ArrangementThe resistance value of the selected resistor shall be close to a nominal value of the calculated value in the application circuit, and the standard series resistor shall be preferred. The tolerance of resistors used in general circuits is ±5%~±10%. Precision resistors should be used in precision instruments and special circuits, with precision within 1%, such as 0. 01%, 0.1% or 0. 5% tolerance. The rated power of the selected resistor should not be arbitrarily increased or reduced in order to meet the requirements of the power capacity of the resistor in the application circuits.If the circuit is required to be a power resistor, the rated power can be 2 times higher than that required by the practical application circuit.Selection of Fuse ResistorFuse resistor, a kind of resistor with a protective function. The dual performance should be considered and the parameters such as resistance and power should be selected according to the specific requirements of the circuits. It is not only to ensure that it can fuse quickly when it is overloaded but also to guarantee that it can work stably for a long time under normal conditions. In addition, if the resistance is too high or the power is too large, it can not play a protective role either.Three basic principles for the selection of resistors:Select high-level standard resistors manufactured by a production line certified by the certification administrations.Select resistors manufactured by manufacturers with advantages of function, quality, efficiency,  price, and service.Select the manufacturer who meets the above requirements.VI Things Needing AttentionThe resistors should be checked before use, checking their performance is to measure whether the actual resistance value is consistent with the nominal value and whether the error is within the allowable range. The method is to measure the resistance by the multimeter.Two points need to pay attention to when measuring.1)The range should be determined according to the measured resistance when the pointer is indicated in the middle of the scale, which is easy to observe.2)After determining the resistor range, having zero adjustments is that the two table pens are directly touching (short circuit), that is, the "zero adjustments" device is adjusted so that the pointer is accurately pointed to the "0" of the Ω scale, and then the resistance value is measured again. Also, be careful not to touch both ends of the resistor or the metal part of the pen, otherwise, the test error will be caused.If the resistance measured by the multimeter is close to the nominal value, the basic quality is good, and if the difference is big or the multimeter does not work at all, this resistor is bad.VII Resistor Detection1. Appearance CheckFor a fixed resistor, check the logo clear firstly: intact protective paint, no charring, no scars, no cracks, no corrosion, resistive body and pin connected closely. For potentiometers, the axis flexible, proper tight, the comfortable handle should be the key point. If there is a switch, checking the switch whether is working properly.2. Multimeter Detection① detection of fixed resistanceWhen measuring, the different resistances are measured by the proper electric gears of the multimeter. For the pointer type multimeter, because the indicator of electric gear is nonlinear, the larger the resistance value, the more dense the indicator number is, so the more accurate the reading is, the larger the angle of needle deviation should be, to make more accurate reading numbers. If the measured result exceeds the error range of the resistor, the resistance value is infinite, unstable, or zero, which indicates that the resistor has been broken.In the measuring process, the hands holding the resistor should not contact the two pins of the resistor, which will affect the accuracy of the measurement. In addition, the multimeter can not be used to detect the resistance during power on, because online detection shouldn’t be allowed.② Detection of fuse resistors and sensitive resistorsThe resistance range of fuse resistors is generally only a few to dozens of Ω. If the detecting resistance is infinite, it indicates that the fuse has been fused. The resistance can also be measured online, measuring the grounding voltage at both ends respectively, if one end is equal to the power supply voltage and another end voltage is 0V, indicating the fuse resistor has broken.There are many kinds of sensitive resistors, in this section, taking thermistors as an example. As above mentioned, it is divided into positive temperature coefficient(PTC) thermistors and negative temperature coefficient(NTC) thermistors. For the PTC thermistor, the resistance value is usually small at normal temperatures. In the measurement, when using the electric soldering iron with burning heat close to the resistor, the resistance value will be obviously increased, which indicates the resistor is normal, and if no change appears, indicating the component is damaged. The NTC thermistor is the opposite.Under the circumstance without light, the resistance value of light-sensitive resistors is large, on the contrary, the measuring resistance will be reduced obviously when there is light, if there is no change, the component is damaged.③ Detection of variable resistors and potentiometerFirstly, measuring whether the resistance values between the two fixed ends are normal, if the detecting values are infinite or zero, or is larger or small than the nominal values, exceeding the tolerances, which indicates the device is damaged. If the resistance value of the resistive body is normal, then a meter pen of the multimeter is connected with the sliding end of the potentiometer, the other pen is connected with any fixed end of the potentiometer (adjustable resistor), and the footstalk is slowly rotated to observe whether the meter needle is stably changed.when the resistance value is changed from zero to the nominal value (or vice versa) from one end to the other end, and there is no jump or jitter in the course of rotation, which indicating the potentiometer is normal, if any, it is indicated that the sliding point of resistance is in poor contact3. Measuring resistance with bridgeIf the accurate measurement of resistor resistance is required, it can be measured by a bridge (digital). The resistance can be read from the display by inserting the resistor into the measuring end of the bridge by selecting an appropriate range. For example, when a resistor is made from a wire or a fixed resistor is processed to obtain a more accurate resistance value, under this situation, the resistance of the self-made resistor must be measured by a bridge.Different applications, the purpose of applying varistor, different voltage/current stress acting on the varistor, so the requirements for the varistors are different, thus it is necessary to pay attention to detecting. According to the purpose of the application, the varistors can be divided into two categories: the protection varistor and the circuit function varistor.1) Distinguish between the power supply, signal lines, and data wire protection for varistors, because they should meet the requirements of different technical standards.2) According to the difference of the continuous working voltage applied on the varistors, the power lines can be divided into two types: AC or DC, in addition, the aging characteristics of varistors under these two voltage stresses are different.3) According to the abnormal overvoltage of varistors, it can be divided into three types: surge suppression type, high power type, and high energy type.Surge suppression type: it is used to suppress transient overvoltages caused by lightning and improper operation. Transient overvoltages are random, aperiodic, and the peak value of current voltages may be very large.High power type: it is used to absorb a continuous group of pulses occurring in a period, for example, a varistor connected to a switching power converter, where the impulse voltage period occurs, and the period is knowable, so the energy value can generally be calculated. From this, we can see the peak value of voltage is not large, but occurs frequently, thus its average power is quite large.High energy type: it is used to absorb magnetic energy in large inductance coils such as generator excitation coils, lifting electromagnet coils, etc. For such applying requirements, the main technical index is energy absorption capacity.The protection of varistor can be used repeatedly in most applications, but sometimes it can be made into a one-off protection device such as a current fuse. For example, a varistor with short-circuit contact connected to a load of some current transformers. VIII How to Recognize a Resistor1. Color bands resistorThe first and second bands with four color bands represent the first two digits of the resistance respectively; the third band represents the multiplier; the fourth band represents the tolerance.   ColorDigitMultiplierToleranceBlack0100 Brown11011Red21022Orange3103 Yellow4104 Green51050.5Blue61060.25Violet71071Grey8108 White9109 Gold 10-15Silver 10-210None  20(1) The key to fast recognition is to determine the resistance value within a certain magnitude according to the color of the third band, and then to recognize the resistance of first and second band, following this way, the number can be read out quickly.GoldunitsBlacktensBrownhundredsRedthousandsOrangeten thousandsYellowhundred thousandsGreenmillionsBlueten millions(2) Memorize the number of colors represented by the first and second rings, the following table is the number each color represents.On the order of magnitude, they can be divided into three grades: gold, black, brown is Ω; red, orange, yellow are KΩ; green, blue is MΩ.(3) When the second band is black, the third band is represented by an integer, and a special case at the time of reading needs to be noted, for example, the third band is red, the resistance value is a whole number kΩ.(4) Remember the errors represented by the fourth band color, that is, gold is 5%, silver is 10%, colorless is 20%.Examples(1) When the four-color bands are yellow, orange, red, and gold successively because the third ring is red, the resistance range is several kΩ, according to the representing number of yellow and orange is "4" and "3" respectively, the reading number is 4.3 kΩ, and the fourth band is gold, so the error is 5%.(2) When the four-color bands are brown, black, orange, and gold in turn, because the third band is orange and the second band is black, the resistance range should be tens of kΩ, the brown is representing “1”, so the reading number is 10 kΩ, the fourth band is gold, its error is 5%.2. Chip resistorsChip resistors have the advantages of small size, lightweight, high installation density, high seismic resistance, sound anti-interference ability, and good high-frequency characteristic. It is widely used in computers, mobile phones, electronic dictionaries, medical e-products, video cameras, VCD machines,s, etc.Chip components can be divided into three types according to their shape: rectangular, cylindrical, and special-shaped. There are resistors, capacitors, inductors, transistors, and small integrated circuits. The nominal method of the chip components is different from that of the common components. The following is mainly about the nominal method of chip resistors.The resistance value of a chip resistor is the same as that of a general resistor. There are three methods of nominal resistance, but it is not exactly the same as that of general resistors.1) Digital nominal method (usually for general rectangular chip resistors)This method is using a three-digit number on the resistance body to indicate its resistance. Its first digit and second digit are significant digits, and the third digit represents the numbers of "0" added after the significant number, and this digit place does not appear as a letter.Example: “472′” represents “4700Ω”, “151” represents “150”.If it is a decimal, use "R" to denote "decimal point" and take up an effective digit, and the remaining two digits are valid numbers.Example: “2R4” represents “2.4Ω”, “R15” represents “0.15Ω”.2) Colour bands nominal method (used in general cylindrical fixed resistors)The chip resistor, like general resistors, is usually indicated by four/five/six bands. The first band and second band are significant numbers and the third band is a multiplier.IX. Resistor FunctionSmall power resistors are usually made of carbon film packaged in plastic shells, while high power resistors are usually wire wound resistors, which are made by metal wires with high resistance wrapped on the porcelain core.If the resistance value of a resistor is close to 0Ω, the resistor has not any effect on the current. In parallel with this kind of resistors, the circuit will be short-circuited and the current is infinitely large. If resistance is very large or infinite, the circuit is in series with such a resistor can be regarded as an open circuit, that is, the current is 0A. The commonly used resistor in the industry is between two these extreme cases. In other words, it has a certain resistance and can pass through a certain current, but the current is not as large as in a short circuit. The resistor's current limiting effect is similar to that of a small diameter tube connected to two large-diameter tubes to limit water flow. It is defined as the resistance corresponding to that 1V voltage is added to the conductor to generate 1A current, in fact, the term "resistance" refers to a property, whereas in electronic products, it often refers to a component such as a resistor.FAQ1. How does a resistor work?A resistor is a little package of resistance: wire it into a circuit and you reduce the current by a precise amount. ... A resistor like this is described as wire-wound. The number of copper turns controls the resistance very precisely: the more copper turns, and the thinner the copper, the higher the resistance.2. What are the 4 types of resistors?Resistor types:Fixed resistors.Variable resistors.Thermistors.Varistors.Light dependent resistors.3. What is resistor and its unit?Resistor is an electrical component that reduces the electric current. The resistor's ability to reduce the current is called resistance and is measured in units of ohms (symbol: Ω). If we make an analogy to water flow through pipes, the resistor is a thin pipe that reduces the water flow.4. What is resistor in simple words?A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses.5. What is the main function of resistor?A resistor is a passive electrical component with the primary function to limit the flow of electric current.6.How do you identify a resistor?Some resistors have contact plates on the bottom. Read the 3 or 4 numbers on the resistor. The first 2 or 3 represent the significant digits and the last indicates the number of 0s that should follow. For example, a resistor reading 1252 indicates a rating of 12,500 ohms or 1.25 kilo-ohms.7. What is resistor formula?According to Ohm's law, the voltage drop, V, across a resistor when a current flows through it is calculated by using the equation V=IR, where I is current in amps (A) and R is the resistance in ohms (Ω). So the voltage drop across R1 is V1=IR1, across R2 is V2=IR2, and across R3 is V3=IR3.8. What is difference between resistor and resistance?Resistance is the property of a conductor, which determines the quantity of current that passes through it when a potential difference is applied across it. A resistor is a electrical componet with a predetermined electrical resistance, like 1 ohm, 10 ohms 100 ohms 10000 ohms etc.9. What are the 2 types of resistors?The resistors are mainly divided into two types, first Fixed Resistors and second, variable resistors. In Fixed resistors, the electrical resistance of the resistor the remains same while in variable resistor it does change with some physical variable.10. What are the five examples of fixed resistor?The different types of fixed resistors include:Wire wound resistor.Carbon composition resistor.Carbon film resistor.Metal film resistor.Metal oxide film resistor.Metal glaze resistor.Foil resistor.11. What can be used as a resistor?Explained another way: an electrical circuit that has a difference of 2 volts, with 1 Ampere of current flowing through it, has a resistance of 2 Ohms. All electrically conductive materials are somewhat resistive, too. Because of this, even a good electrical conductor, such as metal wire, can be used as a resistor.12. How do you use a resistor in a circuit?Dividing voltage: You can also use resistors to reduce voltage to a level that's appropriate for specific parts of your circuit. For example, suppose your circuit is powered by a 3 V battery but a part of your circuit needs 1.5 V. You could use two resistors of equal value to split this voltage in half, yielding 1.5 V.13. What happens if there is no resistor in a circuit?If there really were no resistance in the circuit, the electrons would go around the circuit, and arrive back at the beginning of the circuit with as much energy as the potential difference (the voltage). That final energy is usually what is dissipated as heat or other types of energy by the circuit.14. How do you connect a resistor?Resistors are said to be connected in “Series”, when they are daisy chained together in a single line. Since all the current flowing through the first resistor has no other way to go it must also pass through the second resistor and the third and so on.15. What is the use of resistor color code?Components and wires are coded with colors to identify their value and function. Resistor Color Coding uses colored bands to quickly identify a resistors resistive value and its percentage of tolerance with the physical size of the resistor indicating its wattage rating.You May Also LikeHow to Distinguish Resistor Color Codes? (Axial Resistors)