potentiometer Related Articles
Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips
- Electronic Components
- News Room
- General electronic semiconductor
- Components Guide
- Sort by
- Robots
- Transmitters
- Capacitors
- IC Chips
- PCBs
- Connectors
- Amplifiers
- Memory
- LED
- Diodes
- Transistors
- Battery
- Oscillators
- Resistors
- Transceiver
- RFID
- FPGA
- Mosfets
- Sensor
- Motors, Solenoids, Driver Boards/Modules
- Relays
- Optoelectronics
- Power
- Transformer
- Fuse
- Thyristor
- potentiometer
- Development Boards
- RF/IF
- Semiconductor Information
- Sensors
- PCB
- transistor
IntroductionThe potentiometer is a three-terminal resistive element whose resistances can be adjusted according to a certain change rule. According to it, it is used in a large variety of electrical and electronic circuits, such as voltage dividers, variable resistor, and current controllers. The potentiometer is usually composed of a resistor body and a movable brush. When the brush moves along the resistor body, the resistance value or voltage will be changed at the output end. Due to its special structure and function, it is necessary to pay attention to its damage and take regular maintenance during operation.Potentiometers - Basic IntroductionCatalogIntroductionⅠ Potentiometer Using TipsⅡ How to Clean Potentiometer?Ⅲ How to Test Potentiometer?3.1 General Methods3.2 Variable Potentiometer TestⅤ Replacing Potentiometer with 4 StepsⅠ Potentiometer Using Tips1) The resistor body of the potentiometer is mostly made of polycarbonate synthetic resin. Avoid contact with the following items: ammonia, other amines, aqueous alkali solutions, aromatic hydrocarbons, ketones, lipid hydrocarbons, and strong chemicals (excessive acid-base value), etc. Because chemical reaction with those will affect their performance.2) The terminal of the potentiometer should avoid using water-soluble flux when soldering, which will cause metal oxidation and mold material. In addition, avoid using inferior flux, and poor soldering may cause difficulty in soldering, resulting in poor contact or open circuit.3) If the soldering temperature is too high or the soldering time is too long, it may cause damage to the potentiometer terminals. The pin terminal should be soldered at 235℃±5℃ within 3 seconds, and the soldering space should be more than 1.5mm away from the potentiometer body. Do not use solder to hit through the circuit board when soldering, and wire terminal soldering should be soldered at 350℃±10℃ within 3 seconds. Except that, the terminal should avoid heavy pressure, otherwise it is easy to cause poor contact.4) During soldering, the height of the rosin (flux) entering the printing machine board should be adjusted properly, and the flux should be prevented from entering the potentiometer, otherwise it will cause poor contact between the brush and the resistor, resulting in INT, noise and other undesirable phenomena.Potentiometer Structure5) The potentiometer is best used in the voltage adjustment, and the connection method should choose "①" pin grounding. The current adjustment structure should be avoided, because the contact resistance between the resistor and the contact piece will stop the passage of large currents.6) Avoid condensation or water droplets on the surface of the potentiometer, and avoid using it in a humid place to prevent insulation deterioration or short circuit.7) When installing the rotary potentiometer, the strength should not be too tight to avoid damage to the screw teeth or poor rotation. When install the sliding type potentiometer, avoid using too long screws, otherwise it may affects the movement of the sliding handle, and even directly damages the potentiometer body.8) In the process of putting the potentiometer on the knob, the pushing force used should not be too large (not exceeding the parameter index of the pushing and pulling force of the shaft in the specification note), otherwise it may cause damage to the potentiometer.9) The operating force (rotation or sliding) of the potentiometer will become faster as the temperature rises, and slower as the temperature drops. If the potentiometer is used in a low temperature environment, it needs a kind of special low temperature resistant grease.10) The shaft or sliding handle of the potentiometer should be as short as possible when designing it. The shorter the shaft or sliding handle, the better and stable the hand feel. On the contrary, the longer the shaking, the greater the shaking, and the feel is easy to change.11) The power of the carbon film of the potentiometer can withstand the ambient temperature of 70°C, and its function may be lost when the temperature is higher than it.12) The resistor body of the sealed potentiometer is mostly made of polycarbonate synthetic resin. Avoid mixing with ammonia, aromatic hydrocarbons, lipid hydrocarbons, ketones, and strong chemicals (excessive pH), other amines, alkaline aqueous solution, etc, because they will affect its performance.Potentiometer TypesⅡ How to Clean Potentiometer?The potentiometer is to wrap the carbon sheet with POM, PC, ABS and other plastic materials. After assembly, the carbon sheet will not be exposed to the outside, it is not easy to oxidize, and dust is not easy to enter, which protects the potentiometer body.Cleaning Steps of Potentiometer1) Use a screwdriver to carefully open the sealing cover fixing card of the sealing potentiometer, and remove the protective cover.2) Remove the fixed spring card of the rotating shaft and pull out the rotating shaft.3) If some sealed potentiometers cannot take out the shaft, you can directly wipe the carbon film and the metal contacts on the shaft with a cotton ball dipped in pure alcohol.4) Adjust the position and angle of the metal contacts, changing the contact position with the carbon film and increasing the pressure.5) Apply some lubricating oil or special grease on the carbon film to delay the service life.6) Reinstall and fix the metal cover to complete the entire cleaning process. Ⅲ How to Test Potentiometer?3.1 General Methods1) Before detecting the potentiometer by the method of appearance and manual adjustment, firstly observe its appearance. Rotate the knob to check whether the rotation is smooth, whether the switch is flexible, whether the "click" sound is crisp when the switch is turned on and off, and listen to the sound of friction between the internal contact points of the potentiometer and the resistor body, if there is a loud noises indicate that the quality is not good. Normally, the handle should be slightly damped when turning.2) Using the multimeter to measure the potentiometer, you should first select the appropriate ohm gear of the multimeter according to the nominal resistance of the measured potentiometer and then do the measurement. When measuring, touch the red and black test leads of the multimeter to the pins of the fixed pins on both sides, and the multimeter reading should be the nominal resistance of the potentiometer. If the multimeter reading is much different from the nominal resistance value, it indicates that the potentiometer has been damaged.When the nominal resistance of the potentiometer is normal, then measure its changing resistance and whether the movable contact is in good contact with the resistor (fixed contact). At this time, one test lead of a multimeter is connected to the moving contact pin (usually the middle pin), and the other test lead is connected to a certain contact pin (pins on both sides).After connecting the test leads, the multimeter should display zero or the nominal resistance value, and then rotate the multimeter's shaft from one extreme position to the other extreme position, and the resistance value should continuously change from zero (or nominal resistance) to the nominal resistance value (or zero). During the rotation or sliding of the shaft of the potentiometer, if the pointer of the multimeter moves steadily or the displayed indication changes uniformly, it means that the measured potentiometer is in good condition. If the resistance reading of the multimeter fluctuates when the shaft is rotated, it means the movable contact has a fault with poor contact.3.2 Variable Potentiometer Test1) Measure the total resistance at both ends to see if it matches the nominal value.2) Measuring the resistance between a fixed end and the sliding end: rotary the potentiometer to see if the resistance change is continuous. Then measuring the resistances between the other fixed end and the sliding end, if the measured intermediate resistance value changes discontinuously, it indicates that there is a poor contact in the sliding process.PotentiometersⅣ Replacing Potentiometer with 4 StepsThere are many types of potentiometers, and most models cannot be used interchangeably, otherwise the control effect will not be very good. When replacing it, the nominal resistance value should be the same as the damaged variable resistance value or the close to. At the same time, its packages must be considered, otherwise the installation will be difficult. Therefore, we must distinguish between linear potentiometers, exponential potentiometers and logarithmic potentiometers before use. In addition, please note that the precision resistor can only be replaced with a same one when it is damaged, and cannot be replaced with an ordinary variable resistor, otherwise its adjustment accuracy will also be affected.The potentiometer has multiple pins. In order to prevent the wrong pins from being connected during replacement, the following specific operation steps and methods can be used:Step 1: Remove the set screw of the original potentiometer, but do not take off the leads on the potentiometer.Step 2: Install the new potentiometer and fix it.Step 3: Solder a lead on the original potentiometer pin slice, solder it on the corresponding pin slice of the new potentiometer, and the welding method is the same as the old one.Step 4: In the same way, solder each pin wire. Pay attention, welding the next one and then the other one can avoid the wrong position of the leads being welded to each other. Frequently Asked Questions about Potentiometer Uses and Its Replacement1. What is the use of potentiometer?The measuring instrument called a potentiometer is essentially a voltage divider used for measuring electric potential (voltage); the component is an implementation of the same principle, hence its name. Potentiometers are commonly used to control electrical devices such as volume controls on audio equipment. 2. What causes a potentiometer to fail?An electrical short or open will cause the indication to fail at one extreme or the other. If an increase or decrease in the potentiometer resistance occurs, erratic indicated valve position occurs. 3. What does a potentiometer measure?A potentiometer is an instrument which is used for measurement of potential difference across a known resistance or between two terminals of a circuit or network of known characteristics. A potentiometer is also used for comparing the emf of two cells. 4. How do you troubleshoot a potentiometer?Set your ohmmeter to a setting higher than the total resistance of the potentiometer. For example, if your potentiometer is rated at 1,000 ohms, set your ohmmeter to 10,000 ohms. Look at your potentiometer. There should be three tabs sticking out of it. 5. Does a potentiometer need to be grounded?This configuration also acts as a voltage divider and can be used in a number of ways to control a signal. Like any resistor, potentiometers per se do not need to be connected to the ground plane of the circuit, but in the majority of configurations/uses, they will be.
kynix On 2021-08-13
IntroductionCurrent divider equations and voltage divider formulas help you better understand resistor functions in electronic circuits. The current divider circuit is a parallel circuit in which the source current or power supply current divided into a multiple parallel paths. In a parallel circuit, the terminals of all components are connected together, sharing the same two end nodes. This results in the current to flow or pass through different paths and branches. However, the current through each component can have a different value. While a voltage divider circuit is a very common circuit that takes a higher voltage and converts it to a lower one by using a pair of resistors.The main feature of a parallel circuit is that, although the branch circuit currents are different, the voltages of all connection paths are the same. Therefore, there is no need to find the voltage of each resistor, so that the branch current can be easily found by Kirchhoff's current law (KCL) and Ohm's law.Figure 1. Voltage and Current Divider Current CircuitsCatalogIntroductionⅠ Resistive Voltage Divider CircuitⅡ Resistive Current Divider CircuitⅢ Duality (Electrical Circuits)Ⅳ Frequently Asked Questions about Resistor Voltage Divider and Current Divider Rules and FormulasIn this section, through the discussion of the commonly used resistor series voltage divider circuit and resistors in parallel divider circuit to find their rules. This article contains plenty of equations based on Kirchhoff's current law and Ohm's law for you to master voltage divider and current divider circuits. A Discussion of the Useful Voltage Divider and Current Divider Circuits.Ⅰ Resistive Voltage Divider CircuitIn electronics, a voltage divider (also known as a potential divider) is a passive linear circuit that produces an output voltage that is a fraction of its input voltage. It is a simple circuit which turns a large voltage into a smaller one. The basic voltage divider circuit with two resistors in series as shown in the Figure 2. is analyzed, and some useful formulas are obtained:Figure 2. Basic Voltage Divider CircuitThe following equation is given by Kirchoffs Current Law (KCL):The following equation is given by Kirchoffs Voltage Law (KVL):Equation of voltage current relation of circuit elements:Substituting the Ohm's law of the resistance element into the KVL equation, the calculation formula for the current i is obtained:Then substitute it into the Ohm's law of the resistance element, the voltage division formula for calculating the resistance voltage is obtained:Generally speaking, when N resistors are connected in series, the voltage on the Kth resistor can be calculated according to the following voltage division formula:The resistor series voltage divider formula shows the relationship between the voltage of a certain resistor and the total voltage. The voltage division formula expresses that the voltage of a resistor is proportional to its resistance value, that is, when the resistance increases, the voltage also increases.According to the voltage reference direction obtained by the above voltage divider circuit formula, it can be seen that it has nothing to do with the selection of the current reference direction. When the reference direction of the voltage variable uk or us involved in the formula changes, a negative sign will appear in the formula.As shown in the Figure 3, find the voltage Uab when R=0Ω, 4Ω, 12Ω, ...∞.Figure 3. Voltage Reference DirectionThe voltage Uac and Ubc can be obtained by using the resistor series voltage divider formula:Substituting the resistance R into the above formula, after obtaining the voltage Ubc, then using KVL to obtain the voltage Uab, the calculation result is as follows:It can be seen from the calculation results that as the resistance R increases, the voltage Ubc gradually decreases, and the voltage Uab changes from negative to positive, indicating that its actual direction will varies with the change of the resistance R.The Figure 4. below shows the dual-supply DC voltage divider circuit. Try to find the range of potential change at point a when the sliding end of the potentiometer moves.Figure 4. Dual-supply DC Voltage Divider CircuitSolution: Replace the two potentials of +12V and -12V with two voltage sources to obtain the circuit shown in Figure 4. (b).When the sliding end of the potentiometer moves to the bottom end, the potential at point a is the same as that at point c:When the sliding end of the potentiometer moves to the top, the potential at point a is the same as that at point b:When the sliding end of the potentiometer gradually moves from bottom to top, the potential at point a will continuously change between -10V to 10V.Here discusses the change law of load current i and voltage u when an actual supply powers to a variable resistor load. As shown in the Figure 5, RL is a variable resistance load, and R0 represents the internal resistance of the power supply:Figure 5. Variable Resistor LoadLoad current i:Among them, k=RL/R0 represents the ratio of the load resistance to the internal resistance of the power supply, and isc=us/R0 represents the current when the load is short-circuited.Load voltage u:Among them, uoc=us represents the voltage when the load is open.Power absorbed by load resistor:When the coefficient k=RL/R0 takes different values, a series of relative values of current, voltage and power are calculated, as shown in the following table:K=RL/R000.20.40.60.81.02.03.04.05.0∞i/isc10.8330.7140.6250.5550.50.3330.250.20.1670u/uoc00.1670.2860.3750.4440.50.6670.750.80.8331p/pimax00.5560.8160.9380.98810.8890.750.640.5560According to the above data, the curve of voltage, current and power changing with load resistance can be drawn, as shown in the Figure 6:They show:1. When the load resistance gradually increases from zero, the load current gradually changes from the maximum value isc=us/R0 to zero. When the load resistance is equal to the internal resistance of the power supply, the current is equal to half of the maximum value.2. When the load resistance gradually increases from zero, the load voltage gradually increases from zero to the maximum value uoc=us. When the load resistance is equal to the internal resistance of the power supply, the voltage is equal to half of the maximum value.3. When the load resistance is equal to the internal resistance of the power supply, the current is equal to half of the maximum value, the voltage is equal to half of the maximum value, and the power absorbed by the load resistance reaches the maximum value, and pmax=0.25uocisc.The non-linear change law of the current when the load resistance changes can be seen from the resistance scale of an ordinary multimeter. The circuit model of a multimeter electric blocking is a series connection of a voltage source and a resistor. When we use a multimeter to measure unknown resistance, we should first short-circuit the multimeter and adjust the zero potentiometer pointer to 0Ω. At this time, the current is the largest and the meter pointer is fully deflected. When the short-circuit wire is removed, the pointer of the multimeter returns to ∞, and the measured current is zero at this time.When the multimeter is connected to the measured resistor, as the resistance value changes, the current of the meter head will change accordingly, the pointer will be deflected to the corresponding position, and the measured resistance value can be directly read according to the scale on the surface. There is a special case, when the measured resistance value is just equal to the internal resistance of the multimeter, the current is half of the full deflection current, and the pointer stays in the middle position. Conversely, the internal resistance can be known from the reading in the middle of the multimeter’s electrical barrier scale. For example, the reading of a 500-type multimeter when the pointer stays in the middle position is 10, the internal resistance when using a ×1k electrical barrier is 10kΩ, and the internal resistance is 1kΩ when using a ×100 electrical barrier. If necessary, use Voltage Divider Calculator to calculate the output voltage of a resistor divider circuit for a given set of resistor values and source voltage. Ⅱ Resistive Current Divider CircuitA current divider is defined as a linear circuit that produces an output current that is a fraction of its input current. The following formula describing a current divider is similar in form to that for the voltage divider. The Figure 7. shows a circuit in which a current source supplies power to two parallel resistors, and some useful formulas are drawn from its analysis. Figure 7. Resistive Current Divider CircuitThe following equation is given by Kirchoffs Voltage Law (KVL):The following equation is given by Kirchoffs Current Law (KCL):Equation of current voltage relation of circuit elements:Substituting the Ohm's law of the resistance element into the KCL equation, the calculation formula for the voltage u is obtained:Then substitute Ohm's law into the resistive current divider equation for calculating the resistor current:The resistive current divider formula of two parallel resistors expressed by resistance parameters is:Generally speaking, when n resistors are connected in parallel, the current on the Kth resistor can be calculated according to the following formula:The resistive current divider in parallel formula indicates the relationship between the current of a resistor and the total current. It shows that the resistance current is proportional to its conductance value. For example, the current will increases when the conductance increases.According to the current reference direction obtained by the above formula, it can be seen that it has nothing to do with the selection of the voltage reference direction. When the reference direction of the current is or ik changes, a negative sign will appear in the formula.Figure 8. Resistive Divider CircuitAccording to the characteristics of two resistors in parallel, the current in the 3Ω and 6Ω resistors is obtained:Then, the current in the 12Ω and 6Ω resistors is obtained:Calculate the current i5 in the short-circuit line according to the KCL equation of node a:i5 can also be calculated according to the KCL equation of node b:It should be noted that the current i5=1A in the short circuit is different from the total current. If necessary, the Current Divider Calculator can be used to determine the current going through any branch in a parallel circuit. Enter a current source and resistance values to calculate the current through each resistor. The calculator will display the current through each resistor entered. Ⅲ Duality (Electrical Circuits)According to the above-mentioned analysis of the resistive voltage divider circuit and current divider circuit, there is a certain similarity between them.Figure 9. Duality Circuit ExamplesThe equations of the resistor divider circuit are listed as follows:It can be seen that the equations of these two circuits have a dual relationship. If the current i in the KCL equation of a certain circuit is replaced with the voltage u, the KVL equation of another circuit is obtained; the voltage u in the KVL equation of a certain circuit is replaced with the current i, and the KCL equation of another circuit is obtained. This similar relationship in circuit structure is called topological duality. Similarly, replace u in the VCR equation of a certain circuit with i, i with u, R with G, G with R, etc., you can get the VCR equation of another circuit. This similar relationship of the element VCR equation is called element duality. If two circuits are both topological duality and component duality, they are called dual circuits.The circuit equations of the dual circuit are dual, and the various formulas and results derived therefrom are also dual. For example, the dual formula derived for the dual circuit of Figure 9 (a) and (b) is as follows:This section is a simple analysis of dual circuits, dual formulas, dual theorems and dual analysis methods in order to better grasp the basic concepts of circuit theory and various analysis methods. Here are a few test questions that can be used to test how well you learn about voltage divider and current divider circuits:1) Find the voltages u1 and u2 in the circuit shown in the following figure:2) Find the current i1 and i2 in the circuit shown in the following figure:3) Find the current i2, is and voltage u in the circuit shown in the following figure: Ⅳ Frequently Asked Questions about Resistor Voltage Divider and Current Divider Rules and Formulas1. What is VDR and CDR?The Voltage Divider Rule formula (VDR) shows how the voltage distributes among different resistors in a series circuit. Similarly, the Current Divider Rule formula (CDR) shows how current distributes in a parallel circuit. 2. What is the current divider rule with examples?When two resistors are connected in a parallel circuit, the current in any branches will be a fraction of the total current (IT)). If both the resistors are of equal value, then the current will divide equally through both the branches. 3. Why does a voltage divider need two resistors?One resistor can be used to drop voltage (if the load draws current) but to divide voltage you need something to create a division ratio. To be a voltage divider the output voltage needs to be a constant proportion of the input voltage. ... Note that this need for two resistors only applies to DC. 4. Where are current divider used?By using a current divider, the current flowing through a component can be minimized and thus smaller component size can be used. For example, in a case where larger resistor wattage is required; adding multiple resistors in parallel decreases the heat dissipation, and smaller wattage resistors can do the same job. 5. What is voltage divider formula?A voltage divider is applying a voltage across a series of two resistors. We may draw in a few different ways, but they should always essentially be the same circuit. Thus formula is given as follows: V_{out} = frac{R_b}{R_a+R_b} times V_{in}
kynix On 2021-04-27
IntroductionA voltage divider is a passive linear circuit used to create a voltage less than or equal to the input voltage. It is a conversion device composed of a high-voltage arm and a low-voltage arm. The measured high voltage acts on the device, and the output voltage is got from the low voltage arm. The components of the high and low voltage arms are usually resistors and capacitors. The corresponding devices are called resistor dividers, capacitor dividers, and resistance-capacitance voltage divider. Voltage dividers are one of the most fundamental circuits in electronics.What is Voltage Divider? (voltage divider rule)CatalogIntroductionⅠ Overview of Voltage Divider1.1 Voltage Divider Structure1.2 Voltage Divider CircuitⅡ Types of Voltage DividerⅢ Voltage Divider Characteristics3.1 Voltage Divider Basic3.2 Two Major Points in the Voltage Divider Circuit3.3 Common Voltage Divider Features3.4 Voltage Divider FormulaⅣ Voltage Divider RulesⅤ Voltage Divider PotentiometerⅥ Main Differences between Voltage Divider and TransformerⅠ Overview of Voltage Divider1.1 Voltage Divider StructureThe voltage divider is a special instrument for on-site measurement, measuring DC high voltage and AC high voltage. The voltage divider adopts a balanced equipotential shielding structure, and high-quality electronic components are used inside the body. So that it has the characteristics of accurate test, good linearity, stable performance, reasonable structure, easy to carry, simple operation, intuitive display, etc.Figure 1. Voltage Divider Circuit1.2 Voltage Divider CircuitVoltage usually contains two important terms: electromotive force (EMF) and potential difference (PD). When something provides a voltage, such as a battery, it provides the force required to pull electrons along the circuit because of emf. When a component consumes the voltage in the circuit, the amount of voltage drop on it called potential difference. Some rules about voltage can help circuit design, including:1) Series voltages accumulate.2) The parallel voltage is always the same.3) The PD in the component is proportional to its resistance.4) Polarity is decisive.5) Sum EMF around the circuit is equal to the sum of PD.The rule that voltages in series always accumulate affects both EMF and PD. If the batteries are connected in series, their voltages will add up. If there are series-connected components, then you can apply this rule, whose combined PD is the output voltage. Although it is easy to identify potential differences, make sure to pay close attention to the polarity of the power source. Because the battery reverses minus the combined voltage.Figure 2. An Example of a Series of Voltages Added Up Parallel voltages are always the same. It is one of the reasons why it is not a good idea to connect batteries in parallel with different voltages. For example, when two batteries with different voltages are connected in parallel, the battery with the larger voltage will try to charge the smaller battery, which may damage it.Figure 3. An Example of Parallel Voltage Circuit We have known that the series voltages add up and the voltages in parallel are the same. There are also some questions. How does the voltage separate between the elements in the series circuit? What determines the voltage of each component? The voltage division (called potential difference) is determined by the ratio of the resistance of the element to the resistance of the series circuit. This is directly related to the voltage rule:The value of the PD on the component is proportional to its resistance.Basically, this means that the greater the resistance of the component (compared to the series circuit), the greater its potential difference. In fact, the voltage on the component is equal to When considering the classic divider circuit, the formula is usually written as The following is a typical voltage divider circuit with approximately 3.3V from a 5V power supply:(This circuit can be used to connect a 5V output device to the 3.3V input on the microcontroller, such as particle photon.)Figure 4. An Example of a Classic Voltage Divider Circuit When a voltage (EMF) is applied to the circuit, the sum of all potential differences on the series elements will equal the EMF. For example, the voltage provided by the battery will be divided among the components connected in series, and the sum of all these divided voltages will be equal to the voltage of the battery.Figure 5. Series Voltage Circuit Ⅱ Types of Voltage Divider1. According to the applicationa) For laboratoryb) For power system2. According to the measured voltagea) AC voltage dividerThere are two types: resistive type and capacitive type. The resistive type is composed of non-inductive resistance elements suitable for measuring AC voltages with low frequency. The capacitive type is composed of capacitive elements. It basically does not consume power and can be used for higher voltage measurement. The measurement voltage ranges from thousands of volts to millions of volts. So it has a wide rang applications.b) Impulse voltage dividerImpulse voltage is a non-periodic pulse voltage with fast changes and many harmonic components. To accurately measure its waveform and amplitude, the impulse divider is required to have good response characteristics. There are three types: resistive, capacitive, and resistance-capacitance.c) DC voltage dividerIt is composed of two (groups) resistance elements, and a high-impedance voltmeter is usually used to measure the voltage on the low-voltage arm.Figure 6. High-voltage Divider3. According to the principle of voltage dividera) Capacitor dividerThe capacitor divider used to measure the pulse voltage can be divided into two types. One’s high-voltage arm of a voltage divider is composed of multiple high-voltage capacitors stacked, and the high-voltage arm of the other voltage divider has only one capacitor.The former voltage divider is mostly assembled with an oil-paper-insulated pulse capacitor with an insulating shell, which requires that the inductance of this capacitor is relatively small and can withstand short circuit discharge. A high-voltage oil-paper capacitor is assembled by multiple components in series and parallel. Each component not only has capacitance, but also has inherent inductance and contact resistance in series, as well as parallel insulation resistance. Of course, each component has stray capacitance to ground. This kind of voltage divider should be regarded as a distributed parameter, so it is called a distributed capacitor divider.The distributed capacitor divider is formed by stacking multiple pulse capacitors, with only amplitude error and no waveform error. As for the amplitude error, it can be completely eliminated after calibration with a standard voltage divider. However, when measuring steep waves, since the capacitance of the capacitor divider is much larger than the stray capacitance of the shielding ring of voltage divider, the response time is also much longer. So in terms of measuring steep waves, the response characteristics of the capacitor voltage divider are not as good as the shielded resistor divider. The single-capacitor divider does not consume energy and has no trouble of heating. For measuring waves with a longer wavefront and half-peak time, a capacitor divider is better than a resistor divider. In addition, the capacitor divider can also be used as a load capacitor for adjusting the waveform.The high-voltage arm of the centralized capacitor divider can use a standard capacitor charged with compressed gas. The capacitance value of this capacitor is very accurate and stable, and the dielectric loss is small. Because it is shielded, the capacitance value is not affected by surrounding objects. In power frequency measurement, it has been used very commonly. However, when it is used as an impact capacitor voltage divider, some problems will occur. That is, superimposed high-frequency oscillation.b) Resistor dividerIts internal resistance is pure resistance, with characteristics of simple structure, easy to use, good stability, etc. The error generated by it when measuring the transient pulse voltage is related to the product of the resistance value and the stray capacitance to the ground, so the size and impact of the stray capacitance to the ground should be minimized, and the resistor divider should reduce inductance.c) Resistance-capacitance dividerThe resistance-capacitance voltage divider can be divided into a series-type voltage divider and a parallel-type voltage divider according to the connection mode.The resistor-capacitor series voltage divider is also called the damping capacitor voltage divider. Recently, the high-voltage divider belongs to this type. It overcomes the residual inductance of the capacitor circuit and prevents the voltage divider from oscillating, and has excellent performance. According to the difference of the added damping, the RC series voltage divider can be divided into two types: high damping divider and low damping divider. The high damping capacitor voltage divider cannot be used as the load (wave modulation) capacitor of the impulse voltage generator. It is only used as a conversion device for measuring voltage. The series damping resistance of the low damping capacitor voltage divider is very small, and its connection will not make it difficult to generate standard waves in the test circuit. It can also be used as a load capacitor and is a general voltage divider. From the point of view of ease of use, it has more advantages than the high damping capacitor voltage divider. From the response characteristics, it is not as good as the high damping capacitor voltage divider because it also contains oscillation.Theoretically speaking, when the voltage changes rapidly, the voltage divider ratio is mainly determined by the capacitance; when the change is slow, it is determined by the resistance. The device resistance wire is tightly wound on the porcelain tube positively and negatively, and connected in parallel with each capacitor. Practice has proved that the selected resistance value cannot be too small, otherwise it will affect the output load of the generator, so it is generally selected to be relatively large. However, the effect is small. It is similar to a pure capacitive voltage divider without resistance.Figure 7. Voltage Divider CurrentⅢ Voltage Divider Characteristics3.1 Voltage Divider Basic1) The voltage divider adopts high-precision resistor and capacitor assembly, special process potting, and dry seal, so there is no oil leakage problem. 2) High input impedance: the test current is reduced, the power consumption is small, the product is small and light, the performance is stable, and the measurement accuracy is high. 3) The voltage divider, multi-value kilovolt meter and special cables are all placed in an aluminum alloy box, which is safe and reliable, easy to carry and transport. 4) The multi-value kilovolt meter can directly read the DC average value, AC peak value, effective value, peak value and other voltage values.5)The organic composite insulating jacket is used above 150KV, which increases the surface creeping distance, and greatly reduces the height of the product. So the device is more convenient to use and carry.3.2 Two Major Points in the Voltage Divider Circuit1) Input terminalIt is necessary to analyze where the input signal voltage is input to the voltage divider circuit, and what is the specific input current loop. The method of determining the current loop in circuit analysis is as follows: Start from the input end of the signal voltage, follow at least two components (not necessarily resistors) to the ground.2) Output terminalThe signal voltage output by the voltage divider circuit must be sent to the next level circuit. Theoretically, the input of the next level circuit is the output terminal. However, sometimes it is difficult to analyze the input end of the next-level circuit. So you can use a simpler method to analyze: find all the components in the voltage divider circuit, analyze from the ground line to the upper end, and then find a certain component connects with other circuits. This connection point is the output terminal of the voltage divider circuit, and is also the output voltage of the voltage divider circuit.In the process of analyzing the voltage divider circuit, it is often necessary to figure out the size of the output voltage.The calculation method of the output voltage: Uo=R2/R1+R2·Uiwhere Ui is the input voltage, Uo is the output voltage.The output voltage is less than the input voltage, because the voltage divider circuit attenuates the input signal voltage. That is, changing the size of Rl or R2 resistance can change the output voltage Uo.3.3 Common Voltage Divider FeaturesResistor Divider(1) When it is wound by constantan wire with a small temperature coefficient or kama wire with a small temperature coefficient and high resistance, its temperature stability is high, and the long-term stability is also high during operation. (2) Using a compressive resistor divider structure, its response characteristics may be relatively high.Capacitor Divider(1) The distributed capacitor divider is formed by stacking multiple pulse capacitors, with only amplitude error and no waveform error.(2) The high-voltage arm of the centralized capacitor divider can use a standard capacitor filled with compressed gas. The capacitance value of this capacitor is very accurate and stable, and the dielectric loss is small. Because it is shielded, the capacitance value is not affected by surroundings.Resistance-capacitance DividerThe high damping capacitor voltage divider cannot be used as the load (wave modulation) capacitor of the impulse voltage generator. It is only used as a conversion device for measuring voltage. The series damping resistance of the low damping capacitor voltage divider is very small, and its access will not make it difficult to generate standard waves in the test circuit. It can also be used as a load capacitor, which is a general voltage divider.3.4 Voltage Divider FormulaHow do you calculate voltage divider? In a series circuit, the voltage distribution is proportional to the size of the resistance, that is, the larger the resistance is, the greater the voltage is distributed; on the contrary, the smaller the resistance is, the smaller the voltage is distributed. Voltage divider produces an output voltage (Vout) that is a fraction of its input voltage (Vin).In a series circuit, the voltage across the conductors is proportional to their resistance.By I1=I2, U1/R1=U2/R2 is Using Apogee’s Voltage Divider Calculator helps determine the output voltage of the divider circuit given the input (or source) voltage and the resistor values. Simply enter a few values, and this tool will show the illustrated results for you immediately. Ⅳ Voltage Divider RulesWhen use and test voltage divider, you should take care of the following rules:1) There should be no debris on the test site, so as not to affect the measurement accuracy.2) The ground wire must be connected firmly to ensure a safe operating distance.3) After the test, it must be fully discharged.4) It is strictly prohibited to use over-rated voltage.5) Ensure that the surface of the equipment is clean and stored in a cool, dry place. Ⅴ Voltage Divider PotentiometerThe potentiometer is a varistor that can be used to create an adjustable voltage divider. Its absolute resistance value will not affect the output voltage, and the output voltage is proportional to the input voltage. Commonly used potentiometers have poor resistance accuracy and temperature coefficient. However, as long as the resistance of the potentiometer is uniform, the voltage will be divided evenly. Assuming that the slider is connected to a high-impedance circuit, the contact resistance of the slider will not affect the output voltage. The sliding sheet contact resistance is a value at the contact point of the sliding sheet.When the potentiometer acts as a variable resistor, its resistance accuracy and temperature coefficient will affect the circuit. The contact resistance of the slide will affect the resistance of the circuit, and the contact resistance of the slide will change with changes in position, temperature, vibration and time. Ⅵ Main Differences between Voltage Divider and Transformer1) The transformer changes the ac voltage of by causing the induced electromotive force through the change of the magnetic flux. The capacitor divider changes the alternating voltage through the capacitive reactance during the charging and discharging process.2) The transformer can step up or step down; the capacitor divider cannot step up.3) The input power of the ideal transformer changes with the change of the output power; while the input power of the voltage divider does not change when there is no load.4) When an ideal transformer works, the magnetic flux passing through the iron core is constant. The voltage across the coil follows Faraday's law of electromagnetic induction, in addition, when the voltage divider works, its loop current is a constant value. Frequently Asked Questions about Voltage Divider Rule and Formula1. What is voltage divider rule formula?Using the voltage divider ratio rule, we can see that the largest resistor produces the largest I*R voltage drop. Thus, R1 = 4V and R2 = 8V. Applying Kirchhoff's Voltage Law shows that the sum of the voltage drops around the resistive circuit is exactly equal to the supply voltage, as 4V + 8V = 12V. 2. What is the purpose of a voltage divider?A voltage divider can be used to scale down a very high voltage so that it can be measured by a volt meter. The high voltage is applied across the divider, and the divider output—which outputs a lower voltage that is within the meter's input range—is measured by the meter. 3. What is the voltage divider equation?Voltage Divider Formula / EquationR2 / R1 + R2 = Ratio determines scale factor of scaled down voltage. For example, Vin = 100, R1= 20, R2= 10. 4. What is a voltage divider rule?In electronics, the voltage divider rule is a simple and most important electronic circuit, which is used to change a large voltage into a small voltage. ... When the i/p voltage is applied across the pair of the resistor and the o/p voltage will appear from the connection between them. 5. How does a voltage divider work?A voltage divider can be used to scale down a very high voltage so that it can be measured by a volt meter. The high voltage is applied across the divider, and the divider output—which outputs a lower voltage that is within the meter's input range—is measured by the meter.
kynix On 2021-03-19
IntroductionA potentiometer is a three-terminal resistor with a sliding or rotating contact. It is an adjustable voltage divider with two static contacts and one moving contact. The moving terminal is a wiper that travels across the resistance element, usually in an arc controlled by a rotary knob. Rotating the knob gives a ratiometric division of the potential across the resistance element. Potentiometer generally used in speakers and receivers for volume control. In addition, it cannot directly control the motor because its power is too small. When potentiometer acting as a voltage divider, the absolute resistance of the potentiometer will not affect the output voltage, and its output voltage is proportional to the input voltage.Figure 1. Potentiometer StructureCatalogIntroductionⅠ Potentiometer WiringⅡ Potentiometer Symbol and Diagram DescriptionsⅢ Potentiometer Voltage Divider Circuit BasicsⅣ Potentiometer Resistance MeasuresⅠ Potentiometer WiringThe potentiometer can be used as a three-terminal component or a two-terminal component. The latter can be regarded as a rheostat. For a general potentiometer (three pins), the slider near the center which is a resistance wire. The two pins at both ends of the resistance wire are connected to the input and the ground (some are not connected), respectively. That is, one pin is connected to the input signal and the other pin is grounded. At this time, the resistance wire has a total resistance value on the two sections. You move the sliding piece to go across this resistance wire to get a variable resistance. If the input and output signals are reversed, the sliding direction of the slide is opposite to the resistance change.How to Wire a Potentiometer1) For a potentiometer (or a trimming resistors) with traditional pins (three pins), the resistance at both ends is fixed, and the resistance of the middle pin is variable. That is, the terminal on both sides of the potentiometer are total resistance, and the middle is changing. For example, the power supply is connect from any one contact on resistor sides and output from the middle contact, and the voltage changes with the rotation of the middle contact.Figure 2. Potentiometer Voltage Divider Output2) Although the resistance can vary with the slider, the total resistance value of pins is fixed. At this time, the potentiometer is equal to a current controller, and the selected current output terminals must be the sliding terminal. Commonly used potentiometers have poor resistance accuracy and poor temperature coefficient, but as long as the resistance of the potentiometer is uniform, so is the output voltage value.Figure 3. Potentiometer as Voltage Divider3) If a potentiometer used as a variable voltage divider, one contact connects to the input voltage, the middle contact connects to the output voltage, and the other contact can be grounded. When the rotary handle or sliding handle of the potentiometer take action, the movable contact slides on the resistor. At this time, an output voltage that has a certain relationship with the external voltage, wiper angle and travel stroke.4) If a potentiometer used as a variable resistor, one end connects to the input voltage, the middle end connects to the output, and the other end can be suspended or connected to the middle end to obtain a smooth and continuously changing resistance value.Figure 4. Potentiometer Connected as Variable Resistor As above mentioned, a potentiometer can be connected as a variable resistor, if you want to know more info, you can get it from The Differences Between Potentiometer and Adjustable Resistor. Ⅱ Potentiometer Symbol and Diagram DescriptionsNamePotentiometer SymbolDescriptionNormal PotentiometerUse RP (resistor potentiometer) to represent the potentiometer. The symbol in the figure mark the 3 pins of the potentiometer, indicating the chip pins.Potentiometer SwitchS1 is a switch attached to the RP, and S1 is controlled by the RP rotary handle. When you start to turn the handle, after the switch closes, this circuit is the same as a normal potentiometer. This kind of potentiometer is mainly used in volume control circuits with power switches.As a Variable ResistorThe potentiometer at this time can be regarded as a variable resistor.A Potentiometer with dual portDivide the 3 pins of the potentiometer into 4 ends to form a dual-port circuit. That is, terminals 1 and 2 input signals, terminals 3 and 4 output signals, and terminals 2 and 4 are common terminals, which usually connected to the ground of the line.Dual Gang PotentiometersIt has two single potentiometer circuit symbols, which are connected by a dotted line to indicate that the resistances of dual gang potentiometer are adjusted simultaneously, that is, their resistance values increase or decrease at the same time.Half Linear StrokeThis is a special dual gang potentiometer. Two potentiometer travel strokes are synchronized, but their resistance changes are not the same during adjustment. Only one mechanical stroke of this kind of potentiometer changes in resistance, and the resistance value of the silver zone is zero of another one. The silver zone with no resistance is indicated by shading in the circuit symbol. When the moving contact slides up from the middle, the moving piece RP-1 will enter the silver zone, and RP-2 will enter the varistor area; when the moving handle slides down from the middle position, the RP-2 will enter the silver zone, and RP-1 enters the varistor zone. This special potentiometer can be used in a stereo balance controller circuit (a control circuit in stereo equipment).With Central TapIt has one more pin than the ordinary potentiometer, that is, the tapping pin. The tapping pin is set at the middle resistance of the potentiometer, and the resistance between the tap and the two fixed contacts is equal. There are also potentiometers whose taps are not set in the middle position.Figure 5. Potentiometer CircuitsⅢ Potentiometer Voltage Divider Circuit Basics1) The resistor of the potentiometer is mostly made of polycarbonate synthetic resin. The following items should be avoided: ammonia, other amines, aqueous alkali solutions, aromatic hydrocarbons, ketones, lipid hydrocarbons, strong chemicals (excessive pH), etc., otherwise it will affect potentiometer performance.2) When soldering the potentiometer terminals, avoid using water-capacitive flux, which will cause metal oxidation and mold material. Using inferior flux, poor soldering may cause problems in soldering, resulting in poor contact or open circuit.3) If the soldering temperature of the terminal is too high or the soldering time is too long, it may cause damage to the potentiometer. The temperature range of the plug-in potentiometer is 235℃±5℃; the wire bonding type is 350℃±10℃, and the soldering point should be more than 1.5mm away from the potentiometer body. In addition, avoid heavy pressure on the terminals, otherwise it is easy to cause poor contact.4) During soldering, the height of the flux entering the printing machine board should be adjusted properly, and it should be avoided to affect the potentiometer. Because it will cause poor contact between the brush and the resistor, or result in noise.5) The potentiometer is better in the voltage adjustment structure.6) Avoid condensation or water droplets on the surface of the potentiometer, and avoid using potentiometer in a humid place to prevent insulation deterioration or short circuit.7) When fixing the screws of the rotary potentiometer, the strength should not be too strong to avoid poor rotation. For the direct-sliding potentiometer, avoid using too-long screws, otherwise it may hinder the movement of the sliding handle and even damage the potentiometer itself.8) In the process of putting the potentiometer on the knob, the pushing force should not be too large (don’t exceed the parameter index of the rated pushing and pulling force), otherwise it may cause damage to the potentiometer.9) The rotary force of the potentiometer will decrease as the temperature increases, and become smaller as the temperature decreases. If the potentiometer is used in a low temperature environment, it needs special low temperature resistant grease.Figure 6. Potentiometer Voltage Divider Circuit Connections10) If the shaft or sliding handle of the potentiometer is too long, it is easy to shake and cause the instability of the circuit signal.11) The carbon film of the potentiometer can withstand the ambient temperature of 70℃, and its function may be lost when the temperature is higher than 70℃.12) For a adjustable potentiometer, when the DC is allowed to pass through the movable contact, the problem of anodic oxidation may occur. In this case, it is best to connect the component with the negative end and connect the moving contact with the positive end.13) The load current of the adjustable potentiometer cannot be increased at will to keep circuit safety. And actual current measurement would be to put ammeter in series with the potentiometer in the active circuit.14) Do not exceed the rated power when using the adjustable potentiometer. For example, when the power dissipation exceeds the rated value, it will cause the potentiometer to overheat.15) A Potentiometer is sensitive if it is capable of measuring very small potential differences, and shows a significant change in balancing length for a small change in potential difference being measured.16) A DC potentiometer is created by dropping voltage across a set of resistors in series. Different resistors will produce different values. In AC potentiometer, one can use resistors or even inductors or capacitors as impedances which will drop voltages and provide a voltage less than applied voltage.17) If positioned the potentiometer wiper on the center of the resistor element then the voltage at the wiper is 50%; if the wiper is positioned 1/4 of the way from the negative node then the wiper voltage is 1/4th the entire voltage.18) Potentiometer nomenclature: It generally use the direct marking method. Letters and numbers are marked on the potentiometer shell to indicate their model, nominal power, resistance, and the relationship between resistance and rotation angle.If you have any interest, with a deep reading, you can get more info from What is the Voltage Divider Basic and Rule. Ⅳ Potentiometer Resistance MeasuresThe main checking requirements for the potentiometer are: ① The resistance value meets the circuit requirements. ② The connection between the center sliding end and the resistor is good, and the rotation is smooth. For potentiometer with switches, the switch action should be accurate, reliable and flexible. Therefore, the performance of the potentiometer must be checked before use.1) Resistance measurement: First, select the appropriate gear of the multimeter according to the resistance of the measured potentiometer. Whether the resistance between the two ends of the AC is consistent with the nominal resistance. Rotate the sliding contact, and its value should be fixed. If the resistance indicates infinite, the potentiometer is damaged.2) Then measure the contact between the center end and the resistor, that is, the resistance between the two ends of BC. The method is to set the ohm range of the multimeter in the appropriate range. During the measurement, slowly rotate the shaft and observe the reading of the multimeter. Normally, the reading changes steadily in one direction. If there is a jump, drop, or blockage, it means that the movable contact has failures.3) When the center end slides to the head or the end, the resistance value of the center end and the coincident end is 0 for an ideal state. In the actual measurement, there will be a certain value (generally determined by the nominal value, generally less than 5Ω), which is normal. Frequently Asked Questions about Potentiometer Voltage Divider1. How can a potentiometer be used as a voltage divider?Potentiometers can be used as voltage dividers. To use the potentiometer as a voltage divider, all the three pins are connected. One of the outer pins is connected to the GND, the other to Vcc and the middle pin is the voltage output. Basically, the voltage divider is used to turn a large voltage into a smaller one. 2. How does a potentiometer affect voltage?When the potentiometer resistance is decreased (the wiper moves downwards) the output voltage from pin 2 decreases producing a smaller voltage drop across R2. Likewise, when the potentiometer resistance is increased (the wiper moves upwards) the output voltage from pin 2 increases producing a larger voltage drop. 3. What is a dual gang potentiometer?It means two potentiometer combined on the same shaft, enabling the parallel setting of two channels. Most common are single turn potentiometers with equal resistance and taper. 4. How many volts can a potentiometer handle?100 voltsIf the potentiometer is rated at 1 Watt, you can only apply a maximum of 100 volts. I.e 10 mA. That applied to the voltage across the full 10000 ohms. That also means that you cannot pass more than 10 mA into the Wiper.
kynix On 2020-12-10
Executive Summary: Potentiometers in 2026A potentiometer (or "pot") is a three-terminal variable resistor used to control voltage, current, and signal processing in electronic circuits. While traditional mechanical pots remain vital for audio and industrial controls, 2026 trends favor high-precision Digital Potentiometers (DigiPots) and MEMS-based sensors for IoT and robotics applications. This guide covers the latest classification standards, modern applications, and essential maintenance tips for optimal circuit performance.Ⅰ. What is a Potentiometer? (2026 Overview)A potentiometer is a critical three-terminal passive electronic component that functions as an adjustable voltage divider. Ideally suited for applications requiring user-generated input or position sensing, it consists of a resistive element (track) and a sliding wiper. If only two terminals are configured (one end and the wiper), it functions as a variable resistor or rheostat. While the core mechanical construction of potentiometers remains consistent, modern 2026 manufacturing has introduced durable conductive plastics and cermet materials to extend lifecycle and precision.Figure 1: Potentiometer Basics and Modern ClassificationsⅡ. How are Potentiometers Classified?Potentiometers are primarily classified by their movement mechanism (Linear vs. Rotary) and their control method (Analog Mechanical vs. Digital). Understanding these distinctions is crucial for selecting components for 2026-era PCB designs.Table 1. Industry Standard Potentiometer Classifications (2026)Potentiometer TypeClassification Criteria & Modern StandardsBy Resistor MaterialElectrical performance relies on the track material. Common types include wire wound (high power), synthetic carbon film (consumer audio), metal glass glaze, and conductive plastic (high durability >1M cycles). Specialized types use metal foil or metal oxide film for precision aerospace applications.By Working Environment Selected based on IP ratings and stress factors: High-precision, high-resolution, high-power, or high-temperature variants. Modern sealed potentiometers are essential for automotive and outdoor IoT sensors.By Adjustable ResistanceIncludes fully adjustable (user interface), semi-adjustable (trimpots for calibration), and fine-adjustment types. Non-contact options (Hall Effect, Photo-electric) are gaining market share in 2026 to eliminate mechanical wear and "wiper noise."By Construction MechanicsRotary: Standard rotation is 270°–300°. Multi-turn: Uses a worm gear for 10-20 turns, vital for precision calibration.Linear Slider: Standard in audio mixing consoles for visual feedback of levels (faders). By Gang Number Single Gang: Controls one circuit.Dual/Ganged: Two pots on a single shaft, standard for stereo audio volume control to maintain channel balance.By Resistance Taper (Law)Linear (Type B): Resistance changes proportionally to angle. Used for voltage division.Logarithmic (Type A/Audio): Resistance changes logarithmically to match human hearing. Essential for volume controls.By Actuation MethodManual: Hand-turned knobs or sliders.Motorized: Equipped with a servo motor for remote control and "flying fader" automation in studio consoles. Ⅲ. Detailed Guide: Common Types & ApplicationsSelecting the right potentiometer requires understanding the trade-offs between mechanical endurance, noise levels, and precision.3.1 Breakdown of Key Potentiometer VarietiesRheostat (Variable Resistor)A rheostat functions strictly as a two-terminal variable resistor used to control current. While historically significant, in 2026, the term "rheostat" is considered legacy. Modern efficiency standards prefer PWM (Pulse Width Modulation) for current control over resistive rheostats, which dissipate excess energy as heat. However, they remain useful in simple educational circuits or rugged high-power calibration scenarios. Rotary PotentiometersThe rotary potentiometer is the most ubiquitous interface component. It features a resistive track (Carbon or Cermet) and a wiper connected to a rotating shaft. Key Specs: Typical tolerance is 10%-20%. Rotation is usually 270°. 2026 Applications: Smart home dial interfaces, car audio amplifiers, light dimmers (triac control), and older telecommunication equipment. Logarithmic (Audio) PotentiometersAlso known as "Audio Taper" pots. The resistance changes logarithmically to mirror the Weber-Fechner law of human hearing. At the start of rotation, resistance changes slowly; as the angle increases, the resistance shifts rapidly. This ensures that volume adjustments sound natural and linear to the human ear. Linear Potentiometers (Faders)In linear potentiometers (slide pots), the resistance varies directly with the physical distance the slider moves. They are indispensable in audio mixing consoles (EQ, Faders) because they provide immediate visual feedback of the setting. They are also used for precise voltage division in test equipment and battery internal resistance measurements. Digital Potentiometers (DigiPots)The 2026 Standard: Digital potentiometers are CMOS integrated circuits that replace mechanical wipers with digital switching networks. Controlled via protocols like I2C or SPI, they offer vibration immunity, zero mechanical wear, and programmable precision. Use Cases: Programmable gain amplifiers (PGAs), sensor calibration, LCD contrast control, and smart IoT devices where physical knobs are unnecessary. Membrane (Soft) PotentiometersConstructed by printing carbon/graphite onto a flexible substrate. When pressed, the top layer contacts the bottom resistive track. These are ultra-low profile and widely used in modern wearables, medical devices, and robotics tactile sensors. While they have lower accuracy than wirewound types, their form factor is unmatched for compact designs. Wirewound PotentiometersKnown for high power handling and thermal stability. A resistance wire is wrapped around an insulating core. Pros: High precision, high temperature tolerance. Cons: "Zipper noise" (resolution steps) and inductance issues at high frequencies. 3.2 Critical Application: Potentiometric Position SensorsPotentiometers remain one of the most cost-effective methods for measuring displacement in industrial machinery.3.2.1 Resistive Position SensorsThese function as passive transducers. By applying a stable reference voltage across the fixed terminals, the voltage at the wiper becomes directly proportional to the shaft's angle or linear position. They are widely used in joystick controls, valve positioning, and robotics joint feedback.Figure 2. Simple Position Sensor Circuit 3.2.2 Capacitive Position Sensors (Non-Contact Alternative)For environments where mechanical wear is a concern, capacitive sensors are the superior 2026 choice. They measure position by detecting changes in capacitance between a sensor plate and the target object. These are dominant in high-precision semiconductor manufacturing, touchscreens, and fluid level sensing where physical contact is impossible.Ⅳ. Best Practices: How to Use Potentiometers SafelyTo ensure longevity and signal integrity in your circuits, adhere to these maintenance and installation guidelines:Chemical Safety: Avoid exposing polycarbonate synthetic resin pots to ammonia, ketones, or high-acid chemicals, which degrade the housing.Flux Management: Do not use water-compatible fluxes. Poor quality soldering can lead to oxidation, causing "scratchy" audio or open circuits.Soldering Temp: Prevent heat damage. Pin terminals: 235°C ±5°C. Wire terminals: 350°C ±10°C. Keep solder >1.5mm from the body.Internal Contamination: Ensure no flux enters the internal mechanism during soldering to prevent contact noise.Voltage vs. Current: Potentiometers are designed for Voltage Division. Avoid using them as Rheostats (current limiters) for high loads, as the wiper contact resistance cannot handle high current.Moisture Control: Prevent condensation. In humid environments (like marine audio), use sealed or IP67-rated potentiometers.Mechanical Installation: Do not overtighten mounting nuts. For slide pots, ensure screw length doesn't penetrate the casing and jam the fader.Knob Assembly: Support the back of the shaft when pushing on knobs to prevent internal wiper collapse.Temperature Effects: Lubricant viscosity changes with temperature. For sub-zero applications, specify low-temperature grease to maintain smooth rotation.Signal Interference: Keep shafts/sliders short to minimize acting as an antenna for EMI (Electromagnetic Interference).Thermal Derating: Carbon film power ratings drop above 70°C. Ensure adequate ventilation. Ⅴ. Advanced FAQs and Industry Trends5.1 What are the primary potentiometer types?The industry divides them into Linear (Slide) and Rotary types. A third category, Digital Potentiometers (DigiPots), is now standard for automated systems, while Membrane "Soft Pots" serve ultra-thin form factors.5.2 Quick-Fire FAQsFrequently Asked Questions (2026 Updated)1. What is the main function of a potentiometer?It acts as a variable voltage divider to measure EMF, control volume/gain, or sense position. In 2026, it is also a key component in Human-Machine Interfaces (HMI). 2. What are the top 3 modern applications?User Interface: Volume and tone control in audio gear.Robotics: Position feedback servos (servo motors).Industrial: Linear displacement sensors in injection molding machines. 3. How does a potentiometer differ from a rotary encoder?Potentiometers are absolute position sensors (they know where they are on power-up) but have limited rotation. Encoders are digital, have infinite rotation, but typically require homing (calibration) on startup. 4. Why do audio pots use a logarithmic taper?Because human hearing is non-linear. A logarithmic taper matches the ear's sensitivity, creating a smooth perceived increase in volume.{ "@context": "https://schema.org", "@type": "TechArticle", "headline": "Potentiometer Ultimate Guide 2026: Types, Applications, and Selection", "datePublished": "2020-06-08", "dateModified": "2026-01-09", "description": "A comprehensive engineering guide to Potentiometers in 2026. Covers Linear vs Rotary, Digital Potentiometers, wiring diagrams, and maintenance tips for modern electronics.", "articleBody": "A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider...", "mainEntity": { "@type": "FAQPage", "mainEntity": [ { "@type": "Question", "name": "What are the main types of potentiometers?", "acceptedAnswer": { "@type": "Answer", "text": "The three main categories are Rotary Potentiometers (knobs), Linear Potentiometers (sliders/faders), and Digital Potentiometers (DigiPots) which use ICs for control." } }, { "@type": "Question", "name": "What is the difference between a potentiometer and a rheostat?", "acceptedAnswer": { "@type": "Answer", "text": "A potentiometer uses three terminals to divide voltage. A rheostat uses only two terminals (one fixed, one wiper) to restrict current. Modern circuits prefer potentiometers or PWM over rheostats for efficiency." } }, { "@type": "Question", "name": "Where are potentiometers used in 2026?", "acceptedAnswer": { "@type": "Answer", "text": "They are used in audio volume controls, robotic arm position sensing, industrial joystick controls, and as digital calibration trimmers in IoT devices." } } ] }}
Karty On 2020-06-18
CatalogI IntroductionII Definition, Symbol and Labeling of Variable Resistor 2.1 Definition 2.1.1 What is Variable Resistance? 2.1.2 What is Variable Resistor? 2.2 Symbol 2.3 Labeling Method of Variable ResistorIII How The Variable Resistor WorksIV Features of Variable Resistor ShapeV Structure and Function of Variable Resistor 5.1 Basic Structure 5.2 Schematic Diagram of Two Variable Resistors 5.3 The Role of The Variable ResistorVI Types of Variable Resistors 6.1 Resistance box 6.2 Sliding Rheostat 6.3 Potentiometer 6.4 Specific Classification of Variable Resistors 6.4.1 Film Variable Resistor 6.4.2 Wire Wound Variable ResistorVII Typical Application Circuits of Variable Resistor 7.1 Variable Resistor Circuit in Transistor Bias Circuit 7.2 Stereo Balance Control Variable Resistor CircuitVIII Causes and Solutions of Variable Resistor Malfunctions 8.1 Causes of Variable Resistor Malfunctions8.2 Characteristics of Variable Resistor Malfunctions 8.3 Methods For Repairing Variable Resistor 8.4 Testing a Variable Resistor with a Multimeter 8.4.1 Method 8.4.2 PrecautionsIX Active Variable Resistors with Wide Range of Load ImpedanceX One Question Related to Variable Resistors 10.1 Question 10.2 AnswerXI FAQ I IntroductionA resistor is a current-limiting element. After the resistor is connected to the circuit, the resistance of the resistor is fixed. It generally has two pins, which can limit the current flowing through the branch connected to it. Those whose resistance cannot be changed are called fixed resistors, and those with variable resistance are called potentiometers or variable resistors.Setting Up A Variable Resistor, Rheostat, or Fixed ResistorII Definition, Symbol and Labeling of Variable Resistor2.1 Definition2.1.1 What is Variable Resistance?Variable resistance is a kind of resistance, which can play the role of resistance in electronic circuits. The difference from ordinary resistance is its resistance can be continuously changed within a certain range. In some cases where the resistance value is required to change but does not change frequently, a variable resistor can be used. 2.1.2 What is Variable Resistor?A variable resistor is an electronic component with adjustable resistance. It consists of a resistor and a rotating or sliding system. It is usually used in the circuit that needs to adjust the resistance frequently and plays the role of adjusting the voltage, adjusting the current, or controlling the signal. Its main parameters are basically the same as those of the fixed resistor. 2.2 SymbolThe symbol of the variable resistor is R and the unit is Ω. 2.3 Labeling Method of Variable Resistor(1) The variable resistor uses the direct standard method to indicate the nominal resistance value, that is, the nominal resistance value is directly marked on the variable resistor. In the case of high current applications, the variable resistor is also marked with the rated power parameter. In addition, the resistance value of small variable resistors is expressed in three digits, which is the same as that of resistors.(2) For variable resistors used in small-signal circuits, we generally only care about their nominal resistance and have no power requirements. III How The Variable Resistor WorksWhen a voltage is applied between two fixed electric shocks of the resistor body, the position of the contact on the resistor body is changed by rotating or sliding the system, and a position is formed between the movable contact and the fixed contact. Certainly related voltage. In other words, the resistor body of the variable resistor has two fixed ends. By manually adjusting the rotating shaft or sliding handle to change the position of the moving contact on the resistor body, the relationship between the moving contact and any fixed end is changed. The resistance value changes the magnitude of voltage and current. IV Features of Variable Resistor Shape(1) The volume of the variable resistor is larger than that of the general resistor, and at the same time, the variable resistor in the circuit is less, and it can be easily found in the circuit board.(2) There are three pins in the variable resistor, and they are different from each other. One is a moving pin and the other two are fixed. Generally, the two fixed pins can be used interchangeably, but the fixed and moving pins cannot be used interchangeably.(3) There is an adjustment port on the variable resistor. Use a flat-blade screwdriver to protrude into this adjustment port. Turn the screwdriver to change the position of the moving plate and adjust the resistance value.(4) The nominal resistance value can be seen on the variable resistor. This nominal resistance value refers to the resistance value between two fixed chip pins and is also a fixed chip pin and a moving chip pin. The maximum resistance value between.(5) The vertical variable resistor is mainly used in small-signal circuits. Its three pins are vertically downward and mounted vertically on the circuit board. The resistance adjustment port is in the horizontal direction.(6) Horizontal variable resistors are also used in small-signal circuits. Its three pins are at 90 ° to the resistance plane and are mounted vertically on the circuit board with the resistance adjustment port facing upward.(7) The variable resistance of the small plastic case is smaller and has a circular structure. Its three pins are down and the resistance adjustment port is up.(8) Variable resistors (wire-wound structure) for large power applications. The volume is large, and the moving blade can slide left and right to adjust the resistance. V Structure and Function of Variable Resistor5.1 Basic StructureThe variable resistor is chiefly composed of a moving piece, a carbon film body, and three pins. The three pins are two fixed pins (also called fixed pieces) and one moving piece pin. The moving piece of the variable resistor can be rotated left and right. When using a flat-blade screwdriver to reach into the adjustment port and rotate, the contacts on the moving piece can slide on the resistance piece. According to diverse uses, the resistance material of the variable resistor includes metal wire, metal sheet, carbon film, or conductive liquid. For currents of general magnitude, metal-type variable resistors are frequently used. When the current is slight, it is better to use a carbon film type. When the current is large, the electrolytic type is most suitable. 5.2 Schematic Diagram of Two Variable Resistors Figure3. Schematic Diagram of Two Variable Resistors5.3 The Role of The Variable Resistor(1) A variable resistor is an adjustable electronic component, which is composed of a resistor body and a sliding system. The variable resistor resistance is a resistor that can be adjusted for the current or change of the circuit In the case of circuit resistance, the light can be dimmed, and the motor can be controlled to start its speed. (2) The variable resistor mainly controls the current in the series circuit by changing its own resistance, thereby protecting some electrical components with requirements for the current. The variable resistor is generally used in circuits that do not require frequent adjustment, mainly To fix the same value for the resistor. VI Types of Variable Resistors6.1 Resistance BoxVariable resistors are divided into three types: resistance box, sliding rheostat, and potentiometer. The resistance box is a variable resistance device that uses a conversion device to change its resistance value. This conversion device usually adopts a decimal disc type (knob type) structure, and can also adopt a plug type and an end button type structure as required. The circuit of the resistance box can be divided into series lines and series-parallel lines. Compared with the sliding rheostat, the resistance box can continuously change the resistance in the connected circuit, while the sliding rheostat cannot display the resistance value of the connected circuit.Figure4. Resistance Box6.2 Sliding RheostatA sliding varistor is one of the commonly used devices in electricity. Its working principle is to change the resistance by changing the length of the resistance line in the circuit, thereby gradually changing the current in the circuit. The resistance wire of a sliding rheostat is generally a nickel-chromium alloy with a high melting point and a large resistance, and a metal rod is generally metal with low resistance. As a result, when the cross-sectional area of the resistor is constant, the longer the resistance wire, the greater the resistance; the shorter the resistance wire, the smaller the resistance.Figure5. Sliding Rheostat6.3 PotentiometerA potentiometer is a resistance element with three lead-out terminals whose resistance can be adjusted according to certain change law. A potentiometer usually consists of a resistor and a movable brush. When the brush moves along the resistor body, a resistance value or voltage having a certain relationship with the amount of displacement is obtained at the output end. The potentiometer can be used as a three-terminal element or a two-terminal element. The latter can be regarded as a variable resistor. Because its role in the circuit is to obtain an output voltage that has a certain relationship with the input voltage (external voltage), it is called a potentiometer.Figure6. Potentiometer6.4 Specific Classification of Variable ResistorsThe variable resistor can be divided into the film-type variable resistor and wire-wound variable resistor according to the material. 6.4.1 Film Variable ResistorMembrane variable resistors are usually composed of a resistor body (synthetic carbon film), a movable contact (a movable metal reed or a carbon contact), an adjustment part, and three pins (or solder pads). Two of the fixed pins are connected to both ends of the resistor body, and the other pin (center tap) is connected to the movable contact piece. You can change the resistance between the center tap and the two fixed pins by turning the adjustment part with a small flat-blade screwdriver and changing the contact position of the movable contact with the resistor. Membrane variable resistors are available in hermetic, semi-hermetic, and non-hermetic configurations. (1) Fully sealed film variable resistors are also called solid variable resistors. The resistor is made of carbon black, quartz powder, an organic binder and other materials, and then pressed into plastic or epoxy resin. The matrix of the material is polymerized by heating. The movable contacts use carbon contacts and the adjustment parts are made of plastic. The resistor body and the movable contact are sealed by a metal casing (there is an adjustment hole above the metal casing). Its advantage is that it has good dustproof performance and rarely has bad contact failure. (2) The manufacturing process of the resistor body of the semi-sealed film variable resistor and the resistor body of the fully sealed variable resistor is basically the same. The movable contact piece adopts a metal reed, and the outer plastic cover is sealed. When the plastic cover is rotated, the movable contact piece also rotates with it. This variable resistor is easy to adjust, but its dust resistance is not as good as a fully sealed film-type variable resistor. (3) Unsealed film variable resistors are also called chip tunable resistors. The resistor body is made of carbon black, graphite, quartz powder, an organic binder, etc. to form a suspension, which is coated on a glass fiberboard or glue. Made from wooden boards. The movable contact piece uses a metal reed, and the reed has an adjustment hole, and no separate adjustment component is provided. Its disadvantages are poor dust-proof performance, the contacts are susceptible to oxidation, and prone to failure due to poor contact with the synthetic carbon film. 6.4.2 Wire Wound Variable Resistor(1) High-power wire-wound varistor is also called sliding wire varistor, which is divided into axial ceramic tube-type wire-wound variable resistor and porcelain disc-type wire-wound variable resistor. It adopts an unsealed structure.(2) Low-power wire-wound variable resistors include round vertical wire-wound variable resistors, round horizontal wire-wound variable resistors, and square wire-wound variable resistors, all of which are fully sealed. Package structure.In addition, the variable resistor can be divided into a vertical variable resistor and a horizontal variable resistor according to the structure.Figure7. Wire Wound Variable ResistorVII Typical Application Circuits of Variable Resistor7.1 Variable Resistor Circuit in Transistor Bias CircuitThe figure below shows a variable-resistor voltage-dividing bias circuit. In the circuit, the transistor VT1 constitutes a high-frequency amplifier, and RP1, R1, and R2 constitute a voltage-dividing bias circuit. The output voltage of the voltage dividing circuit is determined by the resistance of three resistors, RP1, Rl, and R2. R1 and R2 are fixed resistors. The variable resistor RP1 is adjusted, and then the VT1 static operating current is adjusted. The amount of current determines whether VT1 can work in the best state. Figure8. Variable Resistance Voltage Divider Bias Circuit7.2 Stereo Balance Control Variable Resistor CircuitThe following figure shows the left and right channel gain balance adjustment circuits in the audio amplifier. RP1 in the circuit is a variable resistor in series with R1. Figure9. Left and Right Channel Gain Balance Adjustment Circuit in Audio AmplifierIn the audio circuit, for a two-channel amplifier, we need to strictly require that the left and right channel amplifiers have an equal gain (balanced), but the discreteness of the circuit components makes this impossible. In order to ensure that the gains of the left and right channel amplifiers are equal, left and right channel gain balance adjustment circuit needs to be provided, which is referred to as a stereo balance circuit. In the right channel circuit, the resistance of R2 is determined, so that the gain of the right channel amplifier is fixed. Taking the gain of the right channel amplifier as a reference, changing the resistance of RP1 so that the gain of the left channel amplifier is equal to the gain of the right channel amplifier can achieve the same gain of the left and right channel amplifiers. VIII Causes and Solutions of Variable Resistor Malfunctions8.1 Causes of Variable Resistor Malfunctions(1) The use time is long, causing oxidation.(2) The failure of the circuit caused the variable resistor to overcurrent and burned the carbon film. At this time, the burned trace of the variable resistor can also be seen from the appearance. 8.2 Characteristics of Variable Resistor Malfunctions (1) Damage to the carbon film of the variable resistorThe carbon film of the variable resistor is worn or burned. At this time, the contact between the moving piece and the carbon film is poor or cannot be contacted.(2) Poor contact between the moving piece of the variable resistor and the carbon film causes the contact resistance between the moving piece and the carbon film to increase.(3) The variable resistor pin is broken. 8.3 Methods For Repairing Variable Resistor (1) When the track of the contact of the moving blade on the carbon film is worn, the contact on the moving blade can be bent inward to change the original track of the contact of the moving blade.(2) The contacts of the moving blade are dirty. You can clean the contacts with pure alcohol.(3) There is a disconnection between one stator and the carbon film. At this time, if it is used as a variable resistor (not used as a potentiometer), this stator that is not disconnected can be used instead. Resistance value.(4) A pin is broken due to twisting. A lead can be welded with a hardwire as a pin.Figure10. Test a Variable Resistor8.4 Testing a Variable Resistor with a Multimeter8.4.1 MethodThe detection method of the variable resistor is basically the same as that of the resistor. The resistance between the primers is measured with an ohmic block. The measurement can be performed directly on the circuit board, or the variable resistor can be disconnected from the circuit. (1) Measure the nominal resistance of the variable resistor. The multimeter is placed in the proper range of the ohmic block. The two-meter bars are connected to the two fixed pin pins of the variable resistor. At this time, the measured resistance value should be equal to the nominal resistance value of the variable electrical accessory, otherwise, the variable resistance is explained. The device is damaged. (2) Measure the resistance between the moving resistor and the stator of the variable resistor. The multimeter is placed in the proper range of the ohmic block. One meter rod is connected to the fixed piece, and the other one is connected to the moving piece. In this measurement state, when the variable resistor moving piece is rotated, the needle is deflected and the resistance value increases from zero To the nominal value, or decrease from the nominal value to zero. 8.4.2 PrecautionsDue to the particularity of the variable resistor, the following issues should be noted during the detection process:(1) If the resistance between the moving piece and a fixed piece is 0Ω, at this time, you should see whether the moving piece has turned to the end of the fixed piece. To exclude the effects of external circuits). (2) If the resistance value between the moving piece and any certain piece is greater than the nominal resistance value, it means that the variable resistor has an open circuit fault. (3) In the measurement, if the measured resistance between a moving piece and a certain piece is less than the nominal resistance value, it does not mean that it is damaged, but you should look at the position of the moving piece, which is different from ordinary resistors. (4) When taking off the measurement, you can use the appropriate range of the multimeter's ohmic stop.-One rod is connected to the pin of the pad, and the other rod is connected to afoot. Then use a flat screwdriver to slowly rotate the pad in a clockwise or counterclockwise direction. At this time, the hands should continuously change from 0Ω to the nominal resistance. The same method is used to measure the change of wake value between another fixed film and a moving film. The measurement method and test result should be the same. In this way, the variable resistor is good, otherwise, the variable resistor is damaged.Figure11. Digital MultimeterIX Active Variable Resistors with Wide Range of Load ImpedancePower resistors, variable resistors, and other electronic loads are often used to test power supplies and voltage regulators, as shown in the following figure: Figure12. Active variable resistors with several orders of magnitude constant resistanceAlthough the function is the same as a mechanical potentiometer, it is based on an active device, which can provide a wide range of load resistance, high resistance adjustment resolution, and less heat than a mechanical potentiometer. Analyzing the circuit shown in the figure above, the voltage expressions of the non-inverting and inverting ends of the operational amplifier are: Figure13. FormulaThese two voltages are equal, so Figure14. FormulaThe whole circuit can be regarded as the resistance of the non-inverting terminal IN + and the inverting terminal IN-. The non-inverting and inverting equivalent resistances are constant and independent of the test voltage (VIN). RSENSE includes several series resistors that provide multiple orders of magnitude in impedance selection. For example, if 10Ω is required, the terminal is IN + and "B" near IN-1 (points A, C, and D are not connected). For high power loads, pay attention to the rated power of the sense resistor and nFET. The power supply of the operational amplifier can be a battery or any other DC power supply. Its maximum working current is only 20 μA. It is powered by a 9V battery. Under normal circumstances, the active load can be used for 1-2 years.X One Question Related to Variable Resistors10.1 QuestionVolume control regulator in a CD receiver, radio and amplifier also useA.transistorB.variable resistorC.thermistorD.fixed resistor10.2 AnswerB XI FAQ1. What is a variable resistor do?A variable resistor gives the user more control over the resistance, as it allows for variance or for the resistor to be changed in order to meet the resistance requirements of the user. Changing the resistance as a user is actually very simple. 2. What are the two types of variable resistors?The different types of variable resistors include Potentiometer. Rheostat. Thermistor. 3. What is the difference between a variable resistor and a potentiometer?In the potentiometer, the resistance of the track remains the same as the wiper moves and only the potential on the wiper changes. In a variable resistor, the resistance of the track apparently changes as the wiper moves and short circuits more or less of the track resistance. 4. What is the advantage of a variable resistor?The advantage of variable resistors is that you have more control over the voltage. You can also adjust the amount of voltage flowing through a circuit. 5. What is the symbol of a variable resistor?A variable resistor also called an adjustable resistor, consists of two terminals, where one of the terminals is a sliding or moving contact often known as a wiper. The variable resistor IEC symbol is represented by a rectangular box and an arrow across (or above) it, like that shown in the figure below. 6. How do you identify a variable resistor?The variable resistor is represented by a zig-zag line and an arrow across (or above) it, like that shown in the figure below. 7. How many types of variable resistors are there?Variable resistors can be categorized into three types: Potentiometers. Rheostats. Digital potentiometers. 8. Is LDR a variable resistor?An LDR is a component that has a (variable) resistance that changes with the light intensity that falls upon it. This allows them to be used in light sensing circuits. 9. Do variable resistors have polarity?Resistors are blind to the polarity in a circuit. Thus, you don't have to worry about installing them backward. Current can pass equally through a resistor in either direction. 10. Why is a variable resistor needed in a circuit?Simply put, a variable resistor is able to have its electrical resistance adjusted. These devices are used when working with electrical circuitry because they help to control voltage and/or currents. They specifically work with voltage and currents that are a part of the circuit.
kynix On 2020-03-13
Join our mailing list!
Be the first to know about new products, special offers, and more.
Feature Posts
How Resistors Work: From Basic Principles to Advanced Applications2025-07-30
DC Switching Regulators: Principles, Selection, and Applications2025-05-30
FPGA vs CPLD: In-depth Analysis of Architecture, Performance and Application2025-05-07
MOSFET Technology: Essential Guide to Working Principles & Applications2025-05-04
SMD Resistor: Types, Applications, and Selection Guide2025-04-30