ic Related Articles
Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips
- Electronic Components
- News Room
- General electronic semiconductor
- Components Guide
- Sort by
- Robots
- Transmitters
- Capacitors
- IC Chips
- PCBs
- Connectors
- Amplifiers
- Memory
- LED
- Diodes
- Transistors
- Battery
- Oscillators
- Resistors
- Transceiver
- RFID
- FPGA
- Mosfets
- Sensor
- Motors, Solenoids, Driver Boards/Modules
- Relays
- Optoelectronics
- Power
- Transformer
- Fuse
- Thyristor
- potentiometer
- Development Boards
- RF/IF
- Semiconductor Information
- Sensors
- PCB
- transistor
Scientists often discover interesting things without completely understanding how they work. That has been the case with an experimental memory technology in which temperature and voltage work together to create the conditions for data storage. But precisely how was unknown. But when a Stanford team found a way to untangle the chip’s energy and heat requirements, their tentative findings revealed a pleasant surprise: The process may be more energy efficient than was previously supposed.That’s good news for next-generation mobile devices whose batteries would last longer if they were powering lower energy chips. The group that made this discovery, led by Stanford electrical engineer H.-S. Philip Wong, is presenting the paper when the IEEE International Electron Devices Meeting (IEDM) brings leading researchers to San Francisco Dec. 5.The new technology the team investigated is called resistive random-access memory, or RRAM for short. RRAM is based on a new type of semiconductor material that forms digital zeros and ones by resisting or permitting the flow of electrons.RRAM has the potential to do things that aren’t possible with silicon: for instance, being layered on top of computer transistors in new three-dimensional, high-rise chips that would be faster and more energy efficient than current electronics, which is ideal for smartphones and other mobile devices where energy efficiency is a vital feature.But while engineers can observe that RRAM does store data, they don’t know exactly how these new materials work. “We need much more precise information about the fundamental behavior of RRAM before we can hope to produce reliable devices,” Wong said. So to help engineers understand some of the unknowns, Wong’s team built a tool to measure the basic forces that make RRAM chips work.Graduate student Zizhen Jiang of the Stanford team explained the basics: RRAM materials are insulators, which normally do not allow electricity to flow, she said. But under certain circumstances, insulators can be induced to let electrons flow.Past research had shown how: Jolting RRAM materials with an electric field causes a pathway to form that permitted electron flows. This pathway is called a filament. To break the filament, researchers apply another jolt and the material becomes an insulator again. So each jolt switched the RRAM from zero to one or back, which is what makes the material useful for data storage.But electricity is not the only force at play in RRAM switching. Pumping electrons into any material raises its temperature. That’s the principle behind electric stoves. In the case of RRAM, it was the elevated temperature caused by introducing voltage that induced filaments to form or break. The question was what voltage-induced temperature was needed to cause the switching. No one knew.Before the new Stanford study researchers thought short bursts of voltage, sufficient to generate temperatures of about 1,160ºF – hot enough to melt aluminum – was the switching point. But those were estimates because there was no way to measure the heat generated by an electric jolt. “In order to begin to answer our questions, we had to decouple the effects of voltage and temperature on filament formation,” said Ziwen Wang, another graduate student on the team.Essentially, the Stanford researchers had to heat the RRAM material without using an electric field. So they put an RRAM chip on a micro thermal stage (MTS) device – a sophisticated hot plate capable of generating a wide range of temperatures inside the material.Of course the objective was not merely to heat the material, but also to measure how filaments formed. Here they took advantage of the fact that RRAM materials are insulators in their natural state. That makes them digital zeros. As soon as a filament formed electrons would flow. The digital zero would become a digital one, which the researchers could detect.Using this experimental model, the team put RRAM chips on the burner and cranked up the heat, starting at about 80ºF – roughly the temperature of a warm room – all the way up to 1,520ºF, hot enough to melt a silver coin. Heating the RRAM to various temperatures in between these extremes, the researchers measured precisely if and how RRAM switched from its native zero to a digital one.To their pleasant surprise, the researchers observed that filaments could form more efficiently at ambient temperatures between 80ºF and 260ºF, which is hotter than boiling water – contrary to prior expectation that hotter was better.If confirmed by subsequent research, this would be good news because in a working chip the switching temperature would be created by the voltage and duration of the electric jolt. Efficient switching at lower temperatures would require less electricity and make RRAM more energy efficient and extend battery life when used as the memory in mobile devices.Much work remains to be done to make RRAM memory practical but this research provides the test bed to vary conditions systematically instead of relying on hit-and-miss hunches. “Now we can use voltage and temperature as design inputs in a predictive manner and that is going to enable us to design a better memory device,” Wang said.Reference:MT16JTF51264AZ-1G6M1SDUS5EB-001GMD2202-D192
kynix On 2016-12-07
Use of copper as a fluorescent material allows for the manufacture of inexpensive and environmentally compatible organic light-emitting diodes (OLEDs). Thermally activated delayed fuorescence (TADF) ensures high light yield. Scientists of Karlsruhe Institute of Technology (KIT), CYNORA, and the University of St Andrews have now measured the underlying quantum mechanics phenomenon of intersystem crossing in a copper complex. The results of this fundamental work are reported in the Science Advances journal and contribute to enhancing the energy efficiency of OLEDs. Organic light-emitting diodes are deemed tomorrow's source of light. They homogeneously emit light in all observation directions and produce brilliant colors and high contrasts. As it is also possible to manufacture transparent and flexible OLEDs, new application and design options result, such as flat light sources on window panes or displays that can be rolled up. OLEDs consist of ultra-thin layers of organic materials, which serve as emitter and are located between two electrodes. When voltage is applied, electrons from the cathode and holes (positive charges) from the anode are injected into the emitter, where they form electron-hole pairs. These so-called excitons are quasiparticles in the excited state. When they decay into their initial state again, they release energy.Excitons may assume two different states: Singlet excitons decay immediately and emit light, whereas triplet excitons release their energy in the form of heat. Usually, 25 percent singlets and 75 percent triplets are encountered in OLEDs. To enhance energy efficiency of an OLED, also triplet excitons have to be used to generate light. In conventional light-emitting diodes heavy metals, such as iridium and platinum, are added for this purpose. But these materials are expensive, have a limited availability, and require complex OLED production methods.It is cheaper and environmentally more compatible to use copper complexes as emitter materials. Thermally activated delayed fluorescence (TADF) ensures high light yields and, hence, high efficiency: Triplet excitons are transformed into singlet excitons which then emit photons. TADF is based on the quantum mechanics phenomenon of intersystem crossing (ISC), a transition from one electronic excitation state to another one of changed multiplicity, i.e. from singlet to triplet or vice versa. In organic molecules, this process is determined by spin-orbit coupling. This is the interaction of the orbital angular momentum of an electron in an atom with the spin of the electron. In this way, all excitons, triplets and singlets, can be used for the generation of light. With TADF, copper luminescent material reaches an efficiency of 100 percent.Stefan Bräse and Larissa Bergmann of KIT's Institute of Organic Chemistry (IOC), in cooperation with researchers of the OLED technology company CYNORA and the University of St Andrews, United Kingdom, for the first time measured the speed of intersystem crossing in a highly luminescent, thermally activated delayed fluorescence copper(I) complex in the solid state. The results are reported in the Science Advances journal. The scientists determined a time constant of intersystem crossing from singlet to triplet of 27 picoseconds (27 trillionths of a second). The reverse process – reverse intersystem crossing – from triplet to singlet is slower and leads to a TADF lasting for an average of 11.5 microseconds. These measurements improve the understanding of mechanisms leading to TADF and facilitate the specific development of TADF materials for energy-efficient OLEDs.Reference:KY59-0202NYKY59-S101D2LCD-S301C31TR
kynix On 2016-11-28
Researchers identify specific defects in LED diodes that lead to less efficient solid state lighting
Using state-of-the-art theoretical methods, UCSB researchers have identified a specific type of defect in the atomic structure of a light-emitting diode (LED) that results in less efficient performance. The characterization of these point defects could result in the fabrication of even more efficient, longer lasting LED lighting."Techniques are available to assess whether such defects are present in the LED materials and they can be used to improve the quality of the material," said materials professor Chris Van de Walle, whose research group carried out the work.In the world of high-efficiency solid-state lighting, not all LEDs are alike. As the technology is utilized in a more diverse array of applications—including search and rescue, water purification and safety illumination, in addition to their many residential, industrial and decorative uses—reliability and efficiency are top priorities. Performance, in turn, is heavily reliant on the quality of the semiconductor material at the atomic level."In an LED, electrons are injected from one side, holes from the other," explained Van de Walle. As they travel across the crystal lattice of the semiconductor—in this case gallium-nitride-based material—the meeting of electrons and holes (the absence of electrons) is what is responsible for the light that is emitted by the diode: As electron meets hole, it transitions to a lower state of energy, releasing a photon along the way.Occasionally, however, the charge carriers meet and do not emit light, resulting in the so-called Shockley-Read-Hall (SRH) recombination. According to the researchers, the charge carriers are captured at defects in the lattice where they combine, but without emitting light.The defects identified involve complexes of gallium vacancies with oxygen and hydrogen. "These defects had been previously observed in nitride semiconductors, but until now, their detrimental effects were not understood," explained lead author Cyrus Dreyer, who performed many of the calculations on the paper."It was the combination of the intuition that we have developed over many years of studying point defects with these new theoretical capabilities that enabled this breakthrough," said Van de Walle, who credits co-author Audrius Alkauskas with the development of a theoretical formalism necessary to calculate the rate at which defects capture electrons and holes.The method lends itself to future work identifying other defects and mechanisms by which SRH recombination occurs, said Van de Walle."These gallium vacancy complexes are surely not the only defects that are detrimental," he said. "Now that we have the methodology in place, we are actively investigating other potential defects to assess their impact on nonradiative recombination."Reference:KY59-LM324MMKY59- LM2710KY59- LM3080
kynix On 2016-11-24
Industrial design researchers at Brunel University London have solved two of the major challenges which prevent everyday items of clothing being turned into power sources for smartphones, tablets and other personal tech.Technology to produce super capacitor thread capable of being made into cloth has been around for some time. But until now scientists have been unable to make it provide sufficient voltage for most devices or devise a method to produce it economically outside the lab.Now patented breakthroughs made by colleagues Professors David Harrison and John Fyson, Dr Yanmeng Xu, Dr Fulian Qiu and Ruirong Zhang of Brunel's Department of Design mean thread capable of storing and supplying enough power for common devices and of being manufactured at industrial scale are a reality.Explained Prof Harrison: "Supercapacitors are already ubiquitous as back-up power in phones, PCs and tablets."They store energy without a chemical reaction so can be charged and discharged almost indefinitely. But in thread form they have never before been able to break the 1V barrier."What we have done is show we can produce a multi-layered structure with two sequential capacitive layers capable of producing up to 2V. Breaking the 1V threshold is important as in the real world we work on the voltage of common batteries – 1.5V."We also wanted to address mass production issues so developed a process to semi-automatically coat stainless steel wire the thickness of a human hair with eight separate layers."The work at Brunel is part of the EU-sponsored Powerweave programme which brings together researchers from seven countries to produce textiles which can both generate and store power.Reference:KY36-F17724102900KY36-MKP1841410254KY36-BFC246816474
kynix On 2016-11-22
An ultra-compact implantable image sensor using body channel communication has been demonstrated in Japan. The body channel approach allows the sensor-transmitter device to be much smaller and use less power than an RF wireless unit. Fundamental limitsInterest in implantable medical sensors is on the rise as developments in established technologies and new concepts are making more and more applications feasible. One thing that all such sensors share is the need to be able to get the information they gather within the body, out of the body.RF communication is widely used for such applications, however, with implantable devices size reduction is generally desirable to reduce invasiveness, and in some applications there are also specific size limitations, owing to where and how the sensors are to be implanted. For example, sensors intended for use inside the brain need to be very compact.Using smaller antennas generally means using higher frequencies, and that in turn leads to attenuation problems with biological tissues. To compensate for increased attenuation more power is needed, which is also a serious issue for an implantable device.Conductive communicationAn alternative wireless approach to sending the data is body channel communication, in which an electrical signal is transmitted by conduction through the tissues of the body. In this issue of Electronics Letters, researchers from the Nara Institute of Science and Technology's Graduate School of Materials Science report using this approach to transmit and receive image data from a CMOS sensor fully implanted in a simulated body environment.Their sensor design, using body channel as the transmission method, will allow data to be read from the device by attaching an electrode to the surface of the body near the implantation site, as well as allowing the sensor unit itself to be low-power and small."Our implantable CMOS image sensor is intended for biomedical applications such as brain functional imaging," explains team member Hajime Hayami. "It can be planted with minimum invasiveness. Its features enable implantation of a number of sensors in a brain to investigate collaborative neural activities."In their experiments, the team at Nara have transmitted images from a CMOS sensor submerged in phosphate buffer saline (PBS), a body simulant material, to a receiver electrode 2 mm away. The experiments prove the principle of operation for this form of communication and even this small distance is enough to allow in vivo use in smaller animals."We are planning to apply our device to brain functional imaging of a mouse brain in the near future. Because the size of a mouse brain is only a few mm thick, the transmission distance of 2 mm is sufficient. Even in the case of signal transmission through a longer distance with a larger animal, the experimental results indicate that this method can be applied by adjusting the sensitivity of the receiver circuit," said Hayami.Neural arraysBefore the team can proceed with implantation in an animal, they need to integrate all of their PCB based devices into a single chip. This chip has already been designed and they are now working on the fabrication, with the goal of beginning implantation experiments by the end of 2014.Meanwhile, the Nara researchers have also been working to develop the design and say that relatively long distance transmission is now possible through improvements to the receiver circuit. On the sensor/transmitter side, they have also shown that they can use pulse-width modulation rather than an ADC output from the image sensor.The central goal of their work is creating tools for research into the human brain. "Our research group aims to elucidate the cooperative neural activity with distributed ultra-small sensors in the brain. We think we can achieve the goal by designing more intelligent chips based on the proposed communication method," said Hayami.The team believe that current sociological trends, including aging societies, will continue to drive demand for implantable devices, and that the applications of this kind of technology may develop to include more natural interaction between users and technology. Hayami commented that "I hope we will create an epoch where one can unconsciously use implantable devices by developing a brain-machine interface."Reference:KY45-OVM7695-RAEAKY45- OV09726-A40A-1DKY45- MT9P001I12STC
kynix On 2016-11-22
At the 2015 International Solid State Circuits Conference (ISSCC), nanoelectronics research center imec, in collaboration with Tyndall National Institute, the University of Leuven (KULeuven) and the Ghent University, demonstrated a 4x20Gb/s wavelength division multiplexing (WDM) hybrid CMOS silicon photonics transceiver, paving the way to cost-effective, high-density single-mode optical fiber links.Hybrid CMOS silicon photonics transceivers, transmitting and receiving data over single-mode optical fiber, are expected to play a key role in next-generation datacenter connectivity. By leveraging existing CMOS manufacturing and 3-D assembly infrastructure, the hybrid CMOS silicon photonics platform enables high integration density and reduced power consumption, as well as high yield and low manufacturing cost. Combined with wavelength division multiplexing capability, highly scalable single-mode optical transceivers can be constructed, satisfying the growing need for interconnect bandwidth in next-generation cloud infrastructure.Imec's CMOS silicon photonics transceiver comprises a silicon photonics (SiPh) chip, flip-chip integrated with a low-power 40nm CMOS chip. The SiPh chip, fabricated on imec's 25Gb/s Silicon Photonics Platform (iSiPP25G), comprises an array of four compact 25Gb/s ring modulators, coupled to a common bus waveguide to allow WDM transmission. On the receive side, a ring-based, low-loss (2dB) demultiplexing filter with 300GHz channel spacing is implemented and further connected to an array of four 25Gb/s Ge waveguide photodetectors. Both the ring modulators and the ring WDM filters include highly efficient integrated heating elements to tune their resonant wavelengths to the desired WDM channels. The CMOS chip includes four differential 20Gb/s ring modulator drivers and four 20Gb/s trans-impedance amplifiers. A 12 channel single-mode fiber array is packaged onto the grating coupler array on the chip, using a planar approach developed at Tyndall National Institute.Error-free operation was demonstrated in a 20Gb/s loop-back experiment for all four WDM channels as well as with two channels running together. The dynamic power consumption of the transceiver, including the CMOS driver and receiver, was less than 2pJ/bit. Thermal tuning of the WDM channel wavelengths consumed only 7mW/nm per channel. The transceiver can be further scaled to higher bandwidth capacity by adopting more advanced CMOS technology and by adding more WDM channels, enabling optical modules for 100GbE, 400GbE and beyond for future datacenter interconnects.Reference:KY59-AFBR-5805ZKY59-HFBR-7924EWZKY59-HFBR5320
kynix On 2016-11-09
Join our mailing list!
Be the first to know about new products, special offers, and more.
Feature Posts
How Resistors Work: From Basic Principles to Advanced Applications2025-07-30
DC Switching Regulators: Principles, Selection, and Applications2025-05-30
FPGA vs CPLD: In-depth Analysis of Architecture, Performance and Application2025-05-07
MOSFET Technology: Essential Guide to Working Principles & Applications2025-05-04
SMD Resistor: Types, Applications, and Selection Guide2025-04-30