Phone

    00852-6915 1330

ic Related Articles

Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips

Resistors

Semiconductor Manufacturing Steps with Flow Charts

IntroductionThe manufacture of each semiconductor components products requires hundreds of processes. After sorting, the entire manufacturing process is divided into eight steps: Wafer Processing, Oxidation, Photography, Etching, Film Deposition, Interconnection, Test, and Package.Figure 1. Semiconductor Parts Manufacturing ProcessCatalogIntroductionⅠ Wafer ProcessingⅡ OxidationⅢ PhotomaskⅣ EtchingⅤ Film DepositionⅥ InterconnectionⅦ TestⅧ PackageⅠ Wafer ProcessingFewer people know, all semiconductor processes start with a grain of sand. Because the silicon contained in sand is the raw material needed to produce wafers. A wafer is a round slice formed by cutting a single crystal column made of silicon (Si) or gallium arsenide (GaAs). To extract high-purity silicon materials, silica sand is required, a special material with a silicon dioxide content of up to 95%, which is also the main raw material for making wafers. Wafer processing is the process of making and obtaining wafers.Semiconductor Production Process Explained① Ingot CastingFirst, the sand needs to be heated to separate the carbon monoxide and silicon, and the process is repeated until the ultra-high purity electronic grade silicon (EG-Si) is obtained. High-purity silicon melts into a liquid, and then solidifies into a single-crystal solid form called an "ingot", which is the first step in semiconductor manufacturing. The manufacturing precision of silicon ingots (silicon pillars) is very high, reaching the nano level.② Ingot CuttingAfter the previous step is completed, you need to cut off both ends of the ingot with a diamond saw, and then cut it into slices of a certain thickness. The diameter of the ingot slice determines the size of the wafer. Larger and thinner wafers can be divided into more units, which helps reduce production costs. After cutting the silicon ingot, it is necessary to add a "flat area" or "indent" mark on the slice, so that it is convenient to set the processing direction based on it as a standard in the subsequent steps.③ Wafer Surface PolishingThe thin slice obtained through the above-mentioned cutting process is called a "die", that is, an unprocessed "raw wafer". The die surface is uneven, and it is impossible to directly print circuit patterns on it. Therefore, it is necessary to first remove surface defects through grinding and chemical etching processes, then form a smooth surface through polishing and then cleaning residual contaminants. Ⅱ OxidationThe role of the oxidation process is to form a protective film on the surface of the wafer. It can protect the wafer from chemical impurities, prevent leakage current from entering the circuit, diffusion during ion implantation, and the wafer from slipping off during etching.Figure 2. OxidationThe first step of the oxidation process is to remove impurities and pollutants, such as organic matter, metals and evaporation residual moisture with four steps. After the cleaning is completed, the wafer can be placed in a high temperature environment of 800 to 1200 degrees Celsius, and a layer of silicon dioxide is formed by the flow of oxygen or vapor on the wafer surface. Oxygen diffuses through the oxide layer and reacts with silicon to form oxide layers of different thicknesses, which can be measured after the oxidation is complete.✔️Dry Oxidation and Wet Oxidation MethodAccording to the different oxidants in the oxidation reaction, the thermal oxidation process can be divided into dry oxidation and wet oxidation. The former uses pure oxygen to produce a silicon dioxide layer, which is slow but the oxide layer is thin and dense. The latter requires both oxygen and high solubility. The characteristic of water vapor is that the growth rate is fast, but the protective layer is relatively thick and the density is low.Figure 3. Dry Oxidation and Wet Oxidation MethodIn addition to the oxidizer, there are other variables that affect the thickness of the silicon dioxide layer. First of all, the wafer structure, surface defects and internal doping concentration will affect the rate of formation of the oxide layer. In addition, the higher the pressure and temperature generated by the oxidation equipment, the faster the oxide layer will be formed. In the oxidation process, it is also necessary to use dummy wafers according to the location of the wafers in the unit to protect the wafers and reduce the difference in oxidation degree. Ⅲ PhotomaskPhotomask is the use of light to "print" circuit patterns onto a wafer. We can understand it as semiconductor parts drawing on the surface of the wafer. The higher the fineness of the circuit pattern, the higher the integration of the product chip, which can only be achieved through advanced photomask technology. Specifically, it can be divided into three steps: photoresist coating, exposure and development.① Coated PhotoresistThe first step in drawing a circuit on a wafer is to coat photoresist on the oxide layer. Photoresist changes the chemical properties of the wafer to become "photographic paper". The thinner the photoresist layer on the surface of the wafer, the more uniform the coating, and the finer the patterns that can be printed. In addition, this step can use the "spin coating" method.Figure 4. Coating PhotoresistAccording to the difference of UV light reactivity, photoresist can be divided into two types: positive glue and negative glue. The former will decompose and disappear after being exposed to light, leaving a pattern of unreceived areas, while the latter will polymerize after being exposed to light to let the pattern of the light-receiving part appear.② ExposeAfter covering the photoresist film on the wafer, the circuit can be printed by controlling the light irradiation. This process is called "exposure." We can selectively pass light through the exposure equipment. When the light passes through the mask containing the circuit pattern, the circuit can be printed on the wafer coated with a photoresist film underneath.Figure 5. ExposureDuring the exposure process, the finer the printed pattern, the more components can be accommodated in the final chip, which helps to improve production efficiency and reduce the cost of individual components. ③ DevelopmentThe step after exposure is to spray developer on the wafer, in order to remove the photoresist in the area not covered by the pattern, so that the printed circuit pattern can be revealed. After the development is completed, it needs to be checked by various measuring equipment and optical microscopes to ensure the quality of the drawing of the circuit diagram. Ⅳ EtchingAfter the photolithography of the circuit diagram is completed on the wafer, an etching process is used to remove any excess oxide film and only the semiconductor circuit diagram is left. To do this, liquid, gas or plasma is used to remove the unselected parts.There are two main etching methods, depending on the material used: wet etching that uses a specific chemical solution for chemical reaction to remove the oxide film, and dry etching that uses gas or plasma.1) Wet EtchingFigure 6. Wet Etching MethodWet etching that uses chemical solutions to remove oxide films has the advantages of low cost, fast etching speed, and high productivity. However, wet etching has the characteristics of isotropy, that is, its speed is the same in any direction. This will cause the mask (or sensitive film) and the etched oxide film to not be completely aligned, making it difficult to process very fine circuit diagrams.2) Dry EtchingDry etching can be divided into three different types:The first is chemical etching, which uses etching gas (mainly hydrogen fluoride). Like wet etching, this method is also isotropic, which means that it is not suitable for fine etching.The second method is physical sputtering, that is, ions in the plasma are used to strike and remove the excess oxide layer. As an anisotropic etching method, it has different etching speeds in the horizontal and vertical directions, so its fineness must exceed that of chemical etching. However, the disadvantage of this method is that the etching speed is slow, because it completely relies on the physical reaction caused by ion collision.Figure 7. Physical SputteringThe third method is reactive ion etching (RIE). It combines the first two methods, that is, while using plasma for ionized physical etching, and chemical etching is performed with free radicals generated after plasma activation. In addition to the etching speed exceeding the first two methods, RIE can use the characteristics of ion anisotropy to achieve high-definition pattern etching.Figure 8. Reactive Ion Etching (RIE)Now dry etching has been widely used to improve the yield of fine semiconductor circuits. Maintaining the uniformity of full-wafer etching and increasing the etching speed are crucial. Today's most advanced dry etching equipment is supporting the production of the most advanced logic and memory chips with higher performance. Ⅴ Film DepositionIn order to create the micro devices inside the chip, we need to continuously deposit layers of thin films and remove the excess parts by etching, and add some materials to separate the different devices. Each transistor or memory cell is constructed step by step through the above process. The "thin film" we are talking about here refers to a "membrane" whose thickness is less than 1 micron (μm, one millionth of a meter) and cannot be manufactured by ordinary mechanical processing methods. Here the process of putting a thin film containing the desired molecular or atomic unit on the wafer is "deposition."Figure 9. DepositionTo form a multi-layer semiconductor structure, we need to fabricate a device stack first, that is, alternately stacking multiple thin metal (conductive) films and dielectric (insulating) films on the surface of the wafer, and then repeat the etching process to remove excess parts and form a three-dimensional structure. Technologies that can be used in the deposition process include chemical vapor deposition (CVD), atomic layer deposition (ALD) and physical vapor deposition (PVD). The methods using these technologies can be divided into dry and wet deposition.① Chemical Vapor DepositionFigure 10. Chemical Vapor DepositionIn chemical vapor deposition, the precursor gas chemically reacts in the reaction chamber and generates a thin film attached to the surface of the wafer and by-products that are drawn out of the chamber.Plasma-enhanced chemical vapor deposition requires the use of plasma to generate reactive gas. This method reduces the reaction temperature and is very suitable for temperature-sensitive structures. In addition, the use of plasma can also reduce the number of depositions, which can often lead to higher quality films.② Atomic Layer DepositionFigure 11. Atomic Layer DepositionAtomic layer deposition forms a thin film by depositing only a few atomic layers at a time. The key to this method is to loop the independent steps in a certain order and maintain good control. Coating the precursor on the wafer surface is the first step, after which different gases are introduced to react with the precursor to form the required substances on the wafer surface.③ Physical Vapor DepositionFigure 12. Physical Vapor DepositionPhysical vapor deposition refers to the formation of thin films by physical means. Sputtering is a physical vapor deposition method. Its principle is that atoms of the target material are sputtered out by the bombardment of argon plasma and deposited on the wafer surface to form a thin film.In some cases, the deposited film can be treated and improved by techniques such as ultraviolet heat treatment. Ⅵ InterconnectionThe conductivity of semiconductors is between conductors and non-conductors (ie insulators). This characteristic allows us to fully control the current. Through wafer-based lithography, etching and deposition processes, transistors and other components can be constructed, but they also need to be connected to achieve power and signal transmission and reception.Metal is used for circuit interconnection because of its conductivity, which is need to meet the following conditions:✔️Low Resistance: Since the metal circuit needs to pass current, the metal in it should have low resistance.✔️Thermochemical stability: The properties of the metal material must remain unchanged during the metal interconnection process.✔️High Reliability: With the development of integrated circuit technology, even a small amount of metal interconnect materials must have sufficient durability.✔️Manufacturing Cost: Even if the previous three conditions have been met, high cost is not suitable for the mass production.The interconnection process mainly uses two substances, aluminum (Al) and copper (Co).Figure 13. Al and Co Interconnection Process✔️Aluminum Interconnect ProcessThis process starts with aluminum deposition, photoresist application, and exposure and development, removing any excess aluminum and photoresist before entering the oxidation process through etching tech. After the foregoing steps are completed, repeat them until the interconnection is completed.With its excellent electrical conductivity, aluminum is also easy to lithography, etch, and deposit. In addition, it has a lower cost and a better adhesion to the oxide film. The disadvantage is that it is easy to corrode and has a low melting point. In addition, in order to prevent the reaction of aluminum and silicon from causing connection problems, it is also necessary to add a metal deposit to separate the aluminum from the wafer, which is called a "barrier metal."Aluminum circuits are formed by deposition. After the wafer enters the vacuum state, the thin film formed by aluminum particles will adhere to the wafer. This process is called "Vapour Deposition" and includes chemical vapor deposition and physical vapor deposition.✔️Copper Interconnection ProcessWith the improvement of semiconductor process precision and the shrinking of device size, the connection speed and electrical characteristics of aluminum circuits are gradually unable to meet the requirements. For this reason, we need to find new conductors that satisfy the requirements of both size and cost. With its lower resistance, so it can achieve faster connection speed. What’s more, copper is more reliable because it is more resistant to electromigration than aluminum, which is the movement of metal ions that occurs when current flows through the metal.However, copper does not easily form compounds, so it is difficult to vaporize and remove it from the wafer surface. To solve this problem, we no longer etch copper, but the dielectric materials, so that metal circuit patterns composed of trenches and via holes can be formed, and then copper is filled into the aforementioned to help interconnection, which is called "inlaid process".Figure 14. Copper Interconnection BarriersAs the copper atoms continue to diffuse into the dielectric, the insulation of the latter will decrease and produce a barrier layer that prevents the copper atoms from continuing to diffuse. Then a very thin copper seed layer will be formed on the barrier layer. After this step, electroplating can be carried out, that is, the high-aspect-ratio graphics are filled with copper. After filling, the excess copper can be removed by a metal chemical mechanical polishing (CMP) method. After completion, an oxide film can be deposited, and the excess film can be removed by photolithography and etching processes. The full entire process needs to be repeated continuously until the copper interconnection is completed.It can be seen from the above comparison that the difference between the copper interconnection and the aluminum interconnection is that the excess copper is removed by metal CMP instead of etching. Ⅶ TestThe main goal of the test is to check whether the quality of the semiconductor chip meets a certain standard, thereby eliminating defective products and improving the reliability of the chip. In addition, products that are tested and defective will not enter the packaging step, which helps to save cost and time. Electronic die sorting (EDS) is a testing method for wafers.EDS is a process for inspecting the electrical characteristics of each chip in the wafer state and thereby improving the semiconductor yield. EDS can be divided into five steps, as follows:Electrical Die Sorting (EDS)1)EPMTest whether the electrical parameters of transistors, capacitors, diodes and other devices meet the standards.2)Aging TestTest method of applying a certain temperature and AC/DC voltage to the wafer.3)TestPerform temperature, speed and motion tests on the wafer through the probe card.4)RepairReplace the components in the defective wafer and test again.5)InkUse special ink to mark defective chips.1) EPMEPM is the first step in semiconductor chip testing. This step will test every device (including transistors, capacitors, and diodes) that the semiconductor integrated circuit needs to use to ensure that its electrical parameters meet the standards. The measured electrical characteristic data will be used to improve the efficiency of the semiconductor manufacturing process and product performance (not to detect defective products).2) Wafer Aging TestThe semiconductor defect rate comes from two aspects, namely, the rate of manufacturing defects (higher in the early stage) and the rate of defects occurring throughout the life cycle afterwards. Wafer aging test refers to testing the wafer under a certain temperature and AC/DC voltage to find out which products may have defects in the early stage, that is, to improve the reliability of the final product by discovering potential defects.3) Parameters TestTemp TestHigh TemperaturVerify that the chip can work at a temperature that exceeds the maximum temperature by 10% or higher.Low TemperaturVerify that the chip can work at a temperature that lower the minimum temperature by 10% or more.Room TemperaturCheck whether the chip can work at room temperature (25°C).The high and low temperature test requirements for storage semiconductors are 85-90℃ and -5-40℃ respectively.Speed TestCoreCheck whether the core functions are valid.SpeedTest movement speed.Motion TestDCApply direct current to check whether the current and voltage are normal.ACApply alternating current to test movement characteristics.FunctionCheck whether all functions are normal.4) RepairRepairing is the most important test step, because some defective chips can be repaired, and you only need to replace the defective components.5) InkThe chips that failed the electrical test have been sorted out in the previous steps, but they still need to be marked to distinguish them. In the past, we needed to mark defective chips with special inks to ensure that they can be identified with the naked eye. Today, the system automatically sorts them based on the test data values. Ⅷ PackageSquare chips (also called single wafers) of equal size are formed on the wafers processed by the previous several processes. The next thing to do is to obtain individual chips by cutting. The chip that has just been cut is very fragile and cannot exchange electrical signals, so it needs to be processed separately. This process is packaging, including forming a protective shell on the outside of the semiconductor chip and allowing them to exchange electrical signals with the outside. The entire packaging process is divided into five steps, namely wafer sawing, single wafer attachment, interconnection, molding, and packaging testing.1) Wafer SawingTo cut countless densely arranged chips from the wafer, we must first grind the back of the wafer until its thickness can meet the needs of the packaging process. After grinding, we can cut along the scribing line on the wafer until the semiconductor chip is separated.There are three types of wafer sawing techniques: blade cutting, laser cutting and plasma cutting. Blade cutting refers to cutting wafers with diamond blades, which is prone to generate frictional heat and debris and thus damage the wafers. Laser cutting has higher precision and can easily handle wafers with thin thickness or small scribing line pitch. Plasma cutting uses the principle of plasma etching, so even if the scribing line pitch is very small, this technology can also be applied.2) Single Wafer AttachmentAfter all the chips are separated from the wafer, we need to attach the individual chips (single chip) to the substrate (lead frame). The role of the substrate is to protect the semiconductor chips and allow them to exchange electrical signals with external circuits. A liquid or solid tape adhesive can be used to attach the chip.3) BondFigure 15. BondingAfter attaching the chip to the substrate, we also need to connect the contact points of the two to achieve electrical signal exchange. There are two connection methods that can be used in this step: wire bonding using thin metal wires and flip chip bonding using spherical gold or tin blocks. Wire bonding is a traditional method, and flip-chip bonding can speed up semiconductor product manufacturing.4) MoldingFigure 16. MoldingAfter completing the connection of the semiconductor chip, it is necessary to use a molding process to add a package to the outside of the chip to protect the semiconductor integrated circuit from external conditions such as temperature and humidity. After the packaging mold is made as required, we put the semiconductor chip and the epoxy molding compound (EMC) into the mold and seal it. The sealed chip is in its final product.5) Package TestThe chip that has the final form must pass the final defect test. All that enters the final test is the finished semiconductor chip. They will be put into the test equipment, set different conditions such as voltage, temperature and humidity, etc. for electrical, functional and speed tests. The results of these tests can be used to find defects, improve product quality and production efficiency. Frequently Asked Questions about Semiconductor Manufacturing Steps1. What is a semiconductor and how is it made?Semiconductors are made from materials that have free electrons in their structure that can move easily between atoms, which aids the flow of electricity. ... Silicon has four electrons in its outer orbital, which allows the covalent bonds to form a lattice and thus form a crystal. 2. How many steps are in a manufacturing semiconductor?In semiconductor device fabrication, the various processing steps fall into four general categories: deposition, removal, patterning, and modification of electrical properties. 3. How is semiconductor manufactured?In the manufacturing process of IC, electronic circuits with components such as transistors are formed on the surface of a silicon crystal wafer. A thin film layer that will form the wiring, transistors and other components is deposited on the wafer (deposition). The thin film is coated with photoresist. 4. What type of operation is semiconductor processing?In semiconductor device fabrication, the various processing steps fall into four general categories: Deposition, Removal, Patterning, and Modification of electrical properties. Deposition is any process that grows, coats, or otherwise transfers a material onto the wafer. 5. What chemicals are used in semiconductor manufacturing?Semiconductors chemstry is mainly organized around the chemical treatment by solvents and acido-basic attacks of semiconductors. Chemistry of solvents : the main chemicals used during this stage are trichloroethylene, acetone, isopropanol and also other alcohols such as denatured ethanol.
kynix On 2021-08-18   52465
Resistors

How is a PCB Made Step by Step? Video Explained

IntroductionPrinted Circuit Board(PCB) is a board of most modern electronic devices that has lines and pads that connect various points together. Even if it is a small board, its manufacturing process is very cumbersome and exquisite. Here will introduce the PCB manufacturing process steps by steps with pictures and video.How is PCB made?The following are the detailed PCB producing processes:IntroductionStep 1. PCB CAD FileStep 2. Plate ProductionStep 3. PCB Inner LayersStep 4. Board Punching and CheckingStep 5. LaminationStep 6. DrillStep 7. Copper Chemical Precipitation on the HolesStep 8. PCB Outer LayersStep 9. Computer Control and Copper ElectroplatingStep 1. PCB CAD FileThe first step in PCB production is to organize and check the PCB layout. The PCB manufacturers get the CAD files from the PCB design company, and they will convert them into a unified format-Extended Gerber RS-274X or Gerber X2, because each CAD software has its own unique file format. Then the electronic engineers will check whether the PCB layout conforms to the manufacturing process, and whether there are any defects and other issues.Figure 1. PCB CAD FileWhen making a PCB at home, the PCB layout can be printed on paper with a laser printer, and then transferred to the copper clad laminate. During the printing process, because the printer is prone to lack of ink and breakpoints, it is necessary to manually fill up the ink with an oil-based pen. Figure 2. PCB Laser PrintingHowever, the factory generally uses photocopying to print the PCB layout on the film. If it is a multi-layer PCB, the layout film photocopied on each layer will be arranged in order.Figure 3. PCB Film Arranged in OrderThen the film will be punched with alignment holes. Alignment holes are very important, which is essential to align the materials of each layer of the PCB.Step 2. Plate ProductionClean the copper plate. If there is dust, it may cause the final circuit to be short-circuited or broken.Figure 4. Clean the Copper PlateThe figure below is an example of an 8-layer PCB, which is actually made up of 3 copper clad laminates plus 2 copper films, and then glued them together with prepregs. The production sequence is to start with the middle board (4th- and 5th-layer of circuits), continuously stack together, and then fix. The production of 4-layer PCB is similar, including one core board and two copper films.Figure 5. 8-layer PCB Plate DisplayStep 3. PCB Inner LayersFirst, make the two-layer circuit of the middle core board. After the copper clad laminate is cleaned, it will be covered with a photosensitive film on the surface. This film will solidify when exposed to light, forming a protective film on the copper foil.Figure 6. PCB CoreInsert the two-layer PCB layout film and the double-layer copper clad laminate into the upper PCB layout film to ensure that the upper and lower PCB layout films are stacked accurately.Figure 7. PCB Layout Film PlacingThe machine irradiates the photosensitive film on the copper foil with a UV lamp. The transparent film is cured under the light, and there is still no cured photosensitive film. The copper foil covered under the cured film is the required PCB layout, which is equivalent to the function of the laser printer ink of the manual PCB. In addition, the copper foil covered by the black film will be corroded away, and the cured transparent film will be preserved.Figure 8. Cured Photosensitive FilmClean the uncured photosensitive film with lye, and the required copper foil circuit will be covered by the cured film.Figure 9. Clean Uncured Photosensitive FilmThen use a strong base, such as NaOH, to etch away the unnecessary copper foil.Figure 10. Copper Foil EtchingTear off the cured photosensitive film to expose the copper foil of the required PCB layout.Figure 11. Tear Off the Cured Photosensitive FilmStep 4. Board Punching and CheckingThe core board has been successfully produced. Then punch alignment holes on it to facilitate with other materials.Figure 12. Punch Alignment Holes on PCBOnce the core board is pressed together with other layers, it cannot be modified. So PCB checking is very important. The machine will automatically compare with the PCB layout drawing to find out the error.Figure 13. PCB Layout Drawing ComparisonThe first two layers of PCB boards have been made.Step 5. LaminationA new raw material is introduced here called Prepreg, which is the adhesive among the core boards(PCB layers>4), as well as the core board and the outer copper foil, and it also plays a role in insulation.Figure 14. PCB Prepreg and CopperThe lower copper foil and the two layers of prepreg have been fixed in advance through the alignment hole and the lower iron plate, and then the finished core board is also placed in the alignment hole, and finally the two layers of prepreg, a layer of copper foil and a layer of pressure-bearing aluminum plate covers the core plate.Figure 15. Fixed PCB Prepreg and CopperIn order to improve work efficiency, this factory will stack three different PCB boards together before fixing them. The upper iron plate is magnetically attracted to facilitate alignment with the lower iron plate. After the two layers of iron plates are successfully aligned by inserting the alignment pins, the machine compresses the space between the iron plates as much as possible, and then fixes them with nails.Figure 16. Fixed PCB LayersThe PCB boards clamped by the iron plates are placed on the holder, and then sent to the vacuum heat press for laminating. The high temperature can melt the epoxy resin in the prepreg and fix the core boards and copper foils together under pressure.Figure 17. PCB Layers LaminationAfter the lamination, remove the upper iron plate that presses the PCB. Then remove the pressure-bearing aluminum plate. The aluminum plate also plays the role of isolating different PCBs and ensuring the smoothness of the outer copper foil of the PCB. Finally the PCB taken out at this time will be covered by a layer of smooth copper foil.Figure 18. Remove the Upper Iron Plate and Aluminum PlateStep 6. DrillSo how to connect 4 layers of copper foils that are not in contact with each other in the PCB? First, make the through-hole through the PCB, and then metalize the hole wall to conduct electricity.Figure 19. PCB DrillPut a layer of aluminum plate on the punching machine, and then put the PCB on it. Since drilling is a relatively slow process, in order to improve efficiency, according to the number of layers of the PCB, 1 to 3 identical boards are stacked for drilling together. Finally, cover the uppermost PCB with a layer of aluminum plate. The upper and lower of aluminum plates are used to prevent the copper foil on the PCB from tearing when drilling.Figure 20. PCB DrillNext, you only need to select the correct drilling program on the computer, and the rest is done automatically by the drilling machine. The drill bit is driven by air pressure, and the maximum rotation speed can reach 150,000 revolutions per minute. Because such a high rotation speed is sufficient to ensure the smoothness of the hole wall.Figure 21. Drill ProgramThe replacement of the drill bit is also automatically completed by the machine according to the program. The smallest drill bit can reach a diameter of 100 microns, while the diameter of a human hair is 150 microns.Figure 22. Drill ReplaceIn the previous process, the molten epoxy was squeezed out of the PCB, so it needed to be cut off. Here the profiling milling machine cuts its periphery according to the correct XY coordinates of the PCB.Figure 23. Cuts PCB PeripheryStep 7. Copper Chemical Precipitation on the HolesSince almost all PCB designs use perforations to connect different layers of lines, a good connection requires a 25-micron copper film on the hole wall. The thickness of the copper film needs to be realized by electroplating, but the hole wall is composed of non-conductive epoxy resin and glass fiber board. So the first step is to deposit a layer of conductive material on the hole wall, and form a 1 micron copper film on the entire PCB surface by chemical deposition. The entire process such as chemical treatment and cleaning is controlled by the machine.Step 8. PCB Outer LayersNext, the PCB outer layer is transferred to the copper foil. The process is similar to the transfer principle of the previous PCB inner core board. The PCB layout is transferred to the copper foil by photocopying film and photosensitive film. The only difference is positive films will be used as boards.The transfer of the internal PCB layout described above uses the subtractive method, and the negative film is used as the board. The PCB is covered by the cured photosensitive film as a circuit, and the uncured film is cleaned. After the exposed copper foil is etched, the PCB layout circuit is protected by the cured film. The transfer of the outer PCB layout adopts the normal method, and the positive film is used as the board. The non-circuit area is covered by the cured photosensitive film on the PCB. After cleaning the uncured film, electroplating is performed. Where there is a film, it cannot be electroplated, and where there is no film, copper is plated first and then tin is plated. After the film is removed, alkaline etching is performed, and finally the tin is removed. So the circuit pattern remains on the board because it is protected by tin.Put the cleaned PCB on both sides of the copper foil into the laminating machine, and the photosensitive mold will be pressed onto the copper foil.Figure 24. LaminatorFix the printed PCB layout film of the upper and lower layers through the holes, and put the PCB board in the middle. Then, the photosensitive film under the light-transmitting film is cured by the irradiation of the UV lamp, which is the circuit that needs to be reserved.Figure 25. PCB Expose to the UV LightAfter cleaning off the unnecessary and uncured photosensitive film, inspect the PCB board.Figure 26. PCB CheckingClamp the PCB with clips, and electroplate the copper. As mentioned earlier, in order to ensure that the holes have sufficient conductivity, the copper film plated on the hole walls must have a thickness of 25 microns, so the entire system will be automatically controlled by the computer to ensure its accuracy.Figure 27. PCB Copper PlatingStep 9. Computer Control and Copper ElectroplatingAfter the copper film is electroplated, the computer gives instructions to electroplate a thin layer of tin. Then, check to ensure that the thickness of the plated copper and tin is correct.Figure 28. Electroplated Copper and Tin InspectionNext, a complete automated assembly line completes the etching process. Then, clean the cured photosensitive film on the PCB.Figure 29. Clean Cured Photosensitive FilmThen use a strong alkali to clean the unnecessary copper foil covered by it.Figure 30. Clean the Unnecessary Copper FoilFinally, use the tin stripping solution to strip the tin plating on the PCB layout copper foil. After cleaning, the 4-layer PCB layout is complete. Frequently Asked Questions about PCB Manufacturing Process1. Which are the techniques of PCB manufacturing?There are several PCB manufacturing methods that a PCB can be submitted to before reaching the final product. These methods include preparing the board's surface, placing components, soldering, cleaning, and inspection and testing. 2. What is PCB design process?Step 1 – The DesignStep 2 – Printing the DesignStep 3 – Creating the SubstrateStep 4 – Printing the Inner LayersStep 5 – Ultraviolet LightStep 6 – Removing Unwanted CopperStep 7 – Inspection.Step 8 – Laminating the Layers 3. Which software is best for PCB design?Top 8 Best PCB Design Software of 2021PROTEL (Altium Designer)PADS (PowerPCB)ORCADAllegroEagle (Easily Applicable Graphical Layout Editor)KicadEasyEdaFritzing 4. What is a PCB layer?A PCB is defined as a number of copper layers in a well defined sequence. Copper layers of a PCB are usually just named layers or also called SIGNAL layer. However, to define the complete PCB, other layers are required. They are usually named by their functionality and position. 5. What are the components of a PCB?Some common PCB components include:Battery: provides the voltage to the circuit.Resistors: control the electric current as it passes through them. They’re colour coded to determine their value.LEDs: light emitting diode. Lights up when current flows through it, and will only allow current to flow in one direction.Transistor: amplifies charge.Capacitators: these are components which can harbour electrical charge.Inductor: stores charge and stops and change in current.Diode: allows current to pass in one direction only, blocking the other.Switches: can either allow current or block depending if they are closed or open.
kynix On 2021-08-16   2058
Resistors

How to Test a Current Transformer?

 IntroductionPower systems are more complex than we see. In reality, we cannot see components of electricity, but we can inject how it works (or does not work). A current transformer is one of many elements that come together like a puzzle to form electrical power. A CT is made up of a laminated steel core, a secondary winding around the core, and insulating material surrounding the windings in its most basic form.Current transformers can be used in a variety of metering applications and use, including Wattmeters, power factor meters, watt-hour meters, protective relays, and as trip coils in magnetic circuit breakers, or MCBs.  CatalogIntroductionⅠ What is a Current TransformerⅡ Classification and Types of Current TransformerⅢ The function of Current TransformerⅣ Application of  Current TransformerⅤ Current Transformer Ratio and Polarity    5.1 Current Transformer Ratio  5.2 Current Transformer Polarity    5.3 Electrical Drawing Conventions for CT PolarityⅥ  How to Test CT PolarityⅦ  How to Choose The Right Current Transformer7.1 Genres of System7.2 Requirement of PrecisionⅧ Frequently Asked Questions about Current  Transformer  Ⅰ What is a Current Transformer A current transformer is a device that generates an alternating current in its secondary that is proportional to the alternating current in its primary. When a current or voltage is too high to measure directly, this method is applied. The induced secondary current is then appropriate for measuring instruments or processing in electronic equipment that requires isolation between the primary and secondary circuits.Because high-voltage currents are reduced, a standard ammeter can be used to safely monitor the actual electrical current flowing in an AC transmission line.Figure1: current transformers An electrical CT differs from a voltage or power transformer in that its primary winding has only one or a few turns. It also differs from a voltage transformer in that the prime current is not controlled by the secondary load current but rather by an external load. The CT ratio is the number of secondary turns multiplied by the number of primary turns. This ratio is calculated based on the primary conductor passing through the transformer window once. Ⅱ Classification and Types of Current Transformer There are two categories in the current transformer. The first, a measuring current transformer, is applied to conjunct with measuring devices for current magnitude, energy, and power. The other, a protective current transformer, is used in conjunction with protective equipment such as trip coils, relays, and the like.Current transformers are classified into three basic types: wound, toroidal, and bar.  1. Wound Current Transformer–The primary winding of the transformer is physically connected in series with the conductor carrying the measured current flowing in the circuit. The magnitude of the secondary current is determined by the transformer's turns ratio.  2. Toroidal Current Transformer -There is no primary winding in these. Instead, the line carrying the network's current is threaded through a window or hole in the toroidal transformer. Some current transformers have a "split core," allowing them to be opened, installed, and closed without disconnecting the circuit to which they are connected.  3. Bar-type Current Transformer-The primary winding of this type of current transformer is the actual cable or bus-bar of the main circuit, which is equivalent to a single turn. They are fully insulated from the system's high operating voltage and are typically bolted to the current-carrying device. Bar-type Current Transformer.Figure2: the typical current transformer  Ⅲ The function of Current Transformer One of the functions of the current transformer is to be used for measurement, and it is often used for billing or measuring the current of the equipment in operation. When measuring large alternating currents, to facilitate meter measurement and reduce the risk of direct measurement of high-voltage electricity, it is often necessary to use current transformers to convert them into a more uniform current. Thus, current transformers are considered as the role of current conversion and electrical isolation.Another function is protection : It is frequently used in tandem with a relay device. When a short circuit or overload occurs in the line, the current transformer sends a signal to the relay device to cut off the fault circuit, thereby protecting the power supply system's safety. The current transformer used for protection is not the same as the current transformer used for measurement. It can only operate effectively when the current is tens of times greater than the normal current, and it requires reliable insulation as well as a sufficiently great accurate limit. The coefficient has adequate thermal and dynamic stability.  Ⅳ Application of  Current Transformer Current transformers are widely used for measuring current and monitoring power grid operation. Revenue-grade CTs, along with voltage leads, power the electrical utility's watt-hour meter on many larger commercial and industrial supplies.To isolate high-voltage current transformers from the ground, they are mounted on porcelain or polymer insulators. Some CT configurations wrap around the bushing of a high-voltage transformer or circuit breaker, allowing the conductor to be automatically centered inside the CT window.Current transformers can be installed on a power transformer's low or high-voltage leads. A section of a bus bar can sometimes be removed to replace a current transformer.High-voltage current transformers are mounted on porcelain or polymer insulators to isolate them from the ground. Some CT configurations wrap around the bushing of a high-voltage transformer or circuit breaker, allowing the conductor to be centered inside the CT window automatically.  Ⅴ Current Transformer Ratio and Polarity5.1 Current Transformer RatioAt full load, the CT ratio is the ratio of primary current input to secondary current output. A CT with a ratio of 300:5 is rated for 300 primary amps at full load and will generate 5 amps of secondary current when 300 amps pass through the primary.If the primary current changes, so will the secondary current output. For example, if 150 amps flow through a primary rated at 300 amps, the secondary current is 2.5 amps. Figure3: A current transformer's ratio is equivalent to a potential transformer's voltage ratio.  At full load, the CT ratio is the ratio of primary current input to secondary current output. A CT with a ratio of 300:5 is rated for 300 primary amps at full load and will generate 5 amps of secondary current when 300 amps pass through the primary.If the primary current changes, so will the secondary current output. For example, if 150 amps flow through a primary rated at 300 amps, the secondary current is 2.5 amps.   5.2 Current Transformer PolarityThe polarity of a current transformer is determined by the direction in which the coils are wound around the CT's core (clockwise or counterclockwise), as well as the manner in which the secondary leads are brought out of the transformer case.To ensure an appropriate installation, all current transformers are subtractive polarity and will have the following designations: H1 - Primary current, oriented in the direction of the lineH2 - Primary current in the load-facing directionX1 denotes secondary current (multi ratio CTs have additional secondary terminals) Figure4:  Split-Core CT with a 200A rating. Take note of the polarity marking in the center of the core, which indicates the direction of the source. (Split-Core CT with a 200A rating.) Take note of the polarity marking in the center of the core, which indicates the source's direction. (Photo courtesy of Continental Control Systems, LLC.)The H1 primary lead and the X1 secondary lead are on the same side of a subtractive polarity transformer. When the polarity of a CT is indicated by an arrow, it should be installed with the arrow pointing in the direction of the current flow.When installing and connecting current transformers to power metering and protective relays, it is critical to maintain proper polarity.   5.3 Electrical Drawing Conventions for CT PolarityFor current transformers, polarity markings on electrical drawings and diagrams can be made in a variety of ways. Dots, squares, and slashes are the three most common schematic conventions. On electrical drawings, polarity markings represent H1, which should be facing the source.Figure5: Electrical Drawing Conventions for CT Polarity   Ⅵ  How to Test CT PolarityMaterials need:an analog voltmeter9-volt batteryThe factory has occasionally misapplied markings on current transformers. The following test procedure can verify the polarity of a CT in the field with a 9V battery: Step1: Cut the Power SupplyBefore testing, turn off all power and connect an analog voltmeter to the secondary terminal of the CT to be tested. The meter's positive terminal is connected to CT terminal X1, while the negative terminal is connected to X2.  Step2: Connect the 9-volt BatteryConnect the positive end of the 9-volt battery to the H1 side (sometimes marked with a dot) and the negative end to the H2 side with a piece of wire run through the high side of the CT window. It is critical to avoid continuous contact, which will result in a short circuit of the battery.  Step3: Check the PolarityIf the polarity is correct, the momentary contact causes a tiny positive deflection in the analog meter. If the deflection is negative, the current transformer's polarity is reversed. The terminals X1 and X2 have to be switched before the test.Figure6:The factory has occasionally misapplied markings on current transformers. A 9-volt battery can be used to test the polarity of a CT in the field.   Ⅶ  How to Choose The Right Current TransformerWhen selecting a current transformer for any application, there are numerous factors to consider. As this can be confusing, and there is a lot of inaccurate information out there, it can lead to installing the wrong current transformer and having to replace equipment.To avoid this, the first step should be to contact the current transformer manufacturer if you have any questions or concerns about compatibility. Midwest Current Transformer's team is available to answer your questions and ensure that you are using the correct product. Speaking with our team before ordering current transformers ensures that you have the right equipment for the job, avoiding any last-minute decisions and potential confusion. 7.1 Genres of SystemWhen using any genre of the meter or power system, it is critical to use a current transformer that is specifically designed for that system. It is especially important with meters because they are not all uniformly designed. Another way to put it is that the system's metering or protection is matched with the type of current transformer.It is also critical to understand the primary range of the current transformer and ensure that it is compatible with the application. This type of compatibility is provided by the various configurations of the primary and secondary windings.  7.2 Requirement of PrecisionThe degree of accuracy is critical for current transformers used for measurement. Not all current transformers provide high accuracy, and the more specific the requirement, the more important the quality of data measurement provided by the CT.This accuracy rating is classified according to class, with the current having an effect on the accuracy provided by the current transformer. The ability of the current transformer to perform to the required levels is always a factor in making the right choice for protective transformers..The degree of accuracy is critical for current transformers used for measurement. Not all current transformers provide high accuracy, and the more specific the requirement, the more important the quality of data measurement provided by the CT.This accuracy rating is classified according to class, with the current having an effect on the accuracy provided by the current transformer. The ability of the current transformer to perform to the required levels is always a factor in making the right choice for protective transformers. Ⅷ Frequently Asked Questions about Current Transformer 1.What is the use of current transformer?A Current Transformer (CT) is used to measure the current of another circuit. CTs are used worldwide to monitor high-voltage lines across national power grids. A CT is designed to produce an alternating current in its secondary winding that is proportional to the current that it is measuring in its primary. 2.What is the use of CT and PT?CT is used to measure current while PT is used to measure voltage. CT is connected in series while PT is connected in parallel. CT ratio range is from 1 to 5A while the PT range is from 110V. We connect the output parameter from CT to the ampere meter while we connect the PT output to the voltmeter. 3.What do you mean by a current transformer?A current transformer is a device used to produce an alternating current in its secondary, which is proportional to the AC current in its primary. This is primarily used when a current or voltage is too high to measure directly. ... This ratio is based on the primary conductor passing once through the transformer window. 4.How is CT ratio calculated?When analog ammeters are installed, we can easily determine the CT ratio by observing the meter full scale value and then divide that value by 5. Figure 3. Ammeter with a full scale of 150 amps. The meter in Figure 3 has a full scale of 150 amps. 5 Why CT is connected in series?A CT may be considered as a series transformer. The primary current in a C.T is independent of the secondary circuit conditions (burden/load). The primary winding of the CT is connected in series with the line carrying the current to be measured. Hence it carries of the full line current.   
kynix On 2021-08-13   10951
Resistors

The Best Tech Guide to Electronic Breadboards in 2021

What is Breadboard?When learning how to build a circuit, the breadboard is one of the most basic parts. There are many small jacks on the breadboard, which are specially designed and manufactured for solderless experiments of electronic circuits. A breadboard consists of plastic block holding a matrix of electrical sockets of a size suitable for gripping thin connecting wire, component wires or the pins of transistors and integrated circuits (ICs). The sockets are connected inside the board, usually in rows of five sockets. Since various electronic components can be inserted or pulled out at will according to needs, welding is eliminated, circuit assembly time is saved, and components can be reused, so it is very suitable for the assembly, debugging and training of electronic circuits.What is Breadboard?Topics Covered in this GuideWhat is Breadboard?Why are breadboards called breadboards?How Breadboard Looks like?IC & DIPHow to Use Breadboards?Types of BreadboardsBasic Principles of Breadboard WiringBreadboard Using Tips for BeginnersMaintenance of the BreadboardsWhich Breadboard is Best?What are the Holes in the Breadboard Called?Is a Breadboard Necessary?How much Voltage can a Breadboard Handle?How Does Current Flow in a Breadboard?How Many Amps Can a Breadboard Take?Why are breadboards called breadboards?The name of the breadboard can be traced back to the era of vacuum tube circuits. At that time, most of the circuit components were large in size. People usually fixed them on a wooden board for cutting bread with screws and nails for connection. Later, the circuit components became more and more smaller, but the name of the breadboard is still used. The breadboard most commonly used today is usually made of white plastic and is a pluggable (solderless) breadboard. It was designed by Ronald J. Portugal in 1971.It is a process of verifying ideas by creating an initial model. If you are not sure how a circuit will react normally under a given parameter setting, it is best to build a prototype to test it. For those who are new to electronic circuits, the breadboard is a good start. The advantage of a breadboard is that it can hold the simplest and most complex circuits at the same time. If your circuit cannot be accommodated by the current breadboard, you can splice other boards to adapt to all circuits of different sizes and complexity. Such as integrated circuits (ICs). When you try to master how a module works and need to rewire multiple times, you certainly don't want to solder the circuit interface every time. Once you find a problem, you can disassemble each part to prepare for some troubleshooting. How Breadboard Looks like?The shape of the breadboard is mostly cuboid, with different sizes. The breadboard generally has two layers, the top is a grid shape with double-sided tape adhering to it( you can tore it to fix the breadboard in a certain position). The upper layer of the breadboard is composed of a grid of rows and columns, and there is no conduction between rows.The whole board is made of thermosetting phenolic resin, and there are metal strips at the bottom of the board. Holes are punched at the corresponding positions on the board so that the components can be in contact with the metal strips when inserted into the board, so as to achieve the purpose of conducting electricity. Generally, every 5 orifice plates are connected by a metal strip. There are two rows of vertical jacks on both sides of the board, also a group of 5. These two sets of jacks are used to provide power to the components on the board.Breadboard Layout ExampleSome breadboards have two columns on the left and right sides. These two columns are customarily used as the positive and negative poles of the power supply (This is not necessarily true, depending on your own usage habits and circuit needs). Each of the five grids in the same column of the two columns is a group, which is conductive. But there is no conduction between columns. Then in the middle part, every five columns of grids form a group, and the five grids in this group are conductive. There is generally a groove in the center of the board, which is designed for the needs of integrated circuit (IC) and chip testing, and is used to separate the left and right parts of a board. Some breadboards do not have two columns on the left and right sides due to the size, but the other structures are the same.The motherboard uses a glass fiber board with a conductive layer of copper foil, which is used to fix the solderless breadboard and lead out the power terminal.There may be slight differences in the structure between different breadboards, but they are basically the same. IC & DIPAn unique feature of the breadboard is: Integrated Circuit (IC) and Dual in-line Package (DIP)Dual in-line Package (DIP) Chip:MA2053Do you see the small gap in the middle of the breadboard? There is a reason for this gap, the use of integrated circuits. There are ICs in almost every electronic device. They run motors, regulate voltage, act as timers, perform logic tasks, and perform almost everything you need to perform.ICs can have different numbers of pins, sizes and functions. However, many ICs are suitable for a standard called dual in-line packaging (DIP), which means they all share a set width. As you guessed, the width fits the gap in the middle of the breadboard. This makes it easier to use the IC without having to worry about connecting the wrong pins together. the holes of the breadboard are spaced 0.1” (2.54mm) apart in both the X and Y direction which is the spacing used for adjacent DIP IC leads as well as many other components such as headers.IC & DIP Example on Breadboard How to Use Breadboards?You can use breadboard to make quick electrical connections between components- like resistors, LEDs, capacitors, etc, so that you can test your circuit before permanently soldering it together. Without welding and manual wiring, the circuit and components can be tested by inserting the component into the hole, which is convenient to use. Before use, determine which component's pins should be connected together, and then insert them into the same group of 5 small holes.How to Use a Breadboard?Example: LED Lighting1) MaterialsOne breadboard, several connecting wires (the connecting wires should use needle-shaped wires at both ends), one led light, and one 3V button battery.2) First, put the battery into the battery holder (this can be bought online), and plug it into the breadboard. Then, insert the battery holder into the left and right parts of the breadboard. Parts are separated by grooves to avoid short circuit between the positive and negative poles of the power supply).3) Lead two wires from the positive and negative poles of the battery, and then plug the LED into any two grids that are not conductive on the breadboard (the long pin of the led is positive and the short pin is negative), and finally connect the wires from the positive and negative poles of the battery to the two LED segments.Types of Breadboards1) Solderless BreadboardA solderless breadboard is a motherboard that does not serve as a base, and does not have a soldering power socket to draw out but can expand a single breadboard. Connect the two poles of the power supply to the sockets on both sides of the breadboard, and then you can plug in the components for experiment (the power supply should be disconnected during the process of inserting the components). When more than 5 components or a set of jacks cannot be inserted, you need to connect multiple sets of jacks with a breadboard cable.The advantages of solderless breadboards are small size and easy to carry, but the disadvantages are relatively simple, inconvenient power connection, and small area. It is not suitable for large-scale circuit experiments. If you want to use it for large-scale circuit experiments, you need to fix multiple breadboards on a large wooden board with screws, and then connect them with wires.2) Single BreadboardA single breadboard is a part with a motherboard as a base and a dedicated terminal for power access, and even some breadboards that can perform high-voltage experiments include ground terminals. This kind of board is more convenient to use, that is, directly connect the power supply to the terminal, and then insert the components for experiment (the power supply should be disconnected during the process of inserting the components) when more than 5 components or a set of jacks cannot be inserted, you need to use breadboard cables to connect multiple sets of jacks.The advantage of a single breadboard is that it is small in size, easy to carry, and can easily switch on and off the power supply, but it has a small area and is not suitable for large-scale circuit experiments.3) Composite breadboardComposite breadboard is a board composed of many solderless breadboards. Generally, 2-4 solderless breadboards are fixed on the motherboard, and then the power cords of each board are connected together with the copper foil in the motherboard. The kind of breadboards is also specially designed for different circuit units to control the power supply, so that each board can carry different voltages according to the needs. The use of the composite breadboard is the same as the single breadboard.The advantage of the composite breadboard is that it can conveniently switch on and off the power supply, has a large area to carry out large-scale experiments, and is highly mobile, and has a wide range of uses. However, it is large and heavy for carrying, so it is suitable for laboratories and electronic hobbyists use. Basic Principles of Breadboard WiringComplete the circuit overlap on the breadboard, different people have different styles. However, no matter what style or habit, the following basic principles must be paid attention to when completing the circuit overlap:1. The fewer connection points, the better.Each additional connection point actually increases the probability of failure artificially. There are common faults such as impassability in the breadboard hole, loose wire, and broken wire inside.2. Try to avoid overpasses.The so-called "overpass" means that components or wires ride on other components or wires. Beginner is easy to make such mistakes. It will bring trouble to the replacement of components in the later stage. On the other hand, in the event of a failure, the messy wires can easily make people lose confidence.3. Try to be as reliable as possible.There are two phenomena that need attention:① Breadboard integrated circuits are easy to loosen. Therefore, for integrated circuits such as operational amplifiers, it is necessary to press down forcefully. Once it is not reliable, the position needs to be changed.② The pins of some components on the breadboard are too thin, so please be careful to move them slightly. If you find that they are not secure, you need to change the position.Electronic BreadboardBreadboard Using Tips for Beginners1. When installing discrete components, it should be easy to see their polarity and signs. After placing the component pins, bend them where needed. In order to prevent the exposed leads from short-circuiting, a wire with a sleeve must be used, and the component pins are generally not cut to facilitate repeated use. Generally, do not insert components with a pin diameter> 0.8mm, so as not to damage the elasticity of the contact piece inside the socket.2. The pins of integrated circuits that have been used many times must be repaired neatly, the pins cannot be bent, and all the pins should be slightly skewed outward, so that the lead angles and the jacks can be reliably contacted. The arrangement of the components on the breadboard should be determined according to the circuit diagram in order to facilitate the wiring. In order to be able to correctly route and facilitate wire checking, the insertion direction of all ICs must be kept the same, and which cannot be inserted upside down for the convenience of temporary wiring or to shorten the length of the wire.3. According to the sequence of the signal flow, the method of installation and debugging is adopted. After the components are installed, first connect the power cord and the ground wire. In order to check the line conveniently, try to use different colors for the line. For example, the positive power supply generally uses a red wire, the negative power supply uses the blue, the ground wire uses the black, and the signal wire uses the yellow. Other colors can also be selected according to the real conditions.4. The breadboard should use a single-strand wire with a diameter of about 0.6mm. Cut the wire according to the distance of the wire and the length of the jack. The wire end is required to be cut into a 45º, and the stripped length of the wire end is about 6mm. All the wires are required to be inserted into the bottom plate to ensure good contact. In addition, bare wires should not be exposed to prevent disconnection with other wires.5. The connection is required to be tightly attached to the breadboard to avoid collision and ejection of the breadboard, resulting in poor contact. The wiring must pass around the integrated circuit, and it is not allowed to cross the integrated circuit, and the wires must not be overlapped with each other, try to be horizontal and vertical. This is conducive to line wiring and checking, and components replacement.6. It is best to connect a capacitor with a capacity of tens of microfarads in parallel between the input terminal of each power supply and the ground, so as to reduce the impact of current during transients. In order to suppress the high-frequency components in the power supply, a high-frequency decoupling capacitor should be connected in parallel at both ends of the capacitor, generally 0.01~0.047Uf.7. During the wiring process, it is required to place the various components on the corresponding position on the breadboard and mark the pin numbers used on the circuit diagram to ensure the smooth progress of debugging and troubleshooting.8. All ground wires must be connected together to form a common reference point. Maintenance of the BreadboardsUsing a breadboard is more convenient than using a soldering method, easy to replace wires and components, and can be used multiple times. However, the breadboard should be maintained during daily use. In the multiple use of the breadboard, the spring sheet will become loose and the elasticity will become poor, which is easy to cause poor contact and virtual welding. They are difficult to find out.The breadboard that has been used many times should be uncovered from the back, and the spring sheet with poor elasticity should be taken out, repaired and then inserted into the original position. This can enhance the elasticity and increase the reliability and service life of the breadboard. In addition, pay attention to where the breadboard is used. Large-volume, high-quality or high-power components cannot be plugged into the breadboard because the breadboard jacks are small and the leads of such large components are relatively thick. At this time, the components can only be placed outside the board. Use a single strand of hard wire to solder to the lead, and then insert it into the breadboard.Breadboards are not suitable for high-frequency circuits, because the lead inductance and distributed capacitance of the breadboard are relatively large, which has a great impact on the performance of high-frequency circuits. Breadboard is suitable for integrated circuits, especially for digital integrated circuits, because digital integrated circuits usually have low operating frequency and low power, and they use fewer RC components. It is more difficult for discrete component circuits to use breadboards, especially for circuits with high frequency and high power. Which Breadboard is Best?Best Breadboard Kit ReviewsELEGOO Upgraded Electronics Fun KitREXQualis Electronics Component Fun KitElegoo EL-CP-003 3 MB-102 830-pin solderless PCB board kitFreenove Solderless Breadboard Ultimate Starter KitKeywishbot Electronic Component BreadboardREXQualis Solderless BreadboardKuman GPIO expansion kit for Raspberry PieBoot 3 400-point solderless circuit breadboardPaxcoo 4 breadboard kits with 120 jumper wires for ArduinoSmraza Basic Starter KitSunFounder breadboard kit RAB holderTEKTRUM Solderless plug-in breadboard kitMicrotivity IB401 400-point experiment breadboardElenco 9440 breadboard with 350 jumper wire set kitMakeronics Breadboard + Electronics Fun Kit What are the Holes in the Breadboard Called?Breadboards are designed to work with through-hole electronic components. They have many tiny sockets (called 'holes') arranged on a 0.1" grid. The leads of most components can be pushed straight into the holes. ICs are inserted across the central gap with their notch or dot to the left.The holes in the top-most rail are highlighted in orange and the holes in the bottom-most one are highlighted in green. In the central area of the board are vertical lines of five holes that are electrically connected. These lines of five holes are known as nodes. Is a Breadboard Necessary?Although a breadboard is essential to prototype circuits without having to solder them together and when you have verified that the circuits works you can solder it onto a perfboard. But note that breadboards are never necessary. A properly-milled and constructed panel should generally stay flat under normal conditions, so the only time I add a breadboard end is if I think the design benefits from it visually.In addition, high frequency (above 10MHz) Where the additional breadboard capacitance would present problems (oscillators, etc) Where glitches due to poor wire connections would result in poor operation. Where most of the parts are not through hole 0.1" (2.54mm) centers. How much Voltage can a Breadboard Handle?Breadboards are mostly used for low voltage and current applications, however, breadboards can handle 12 volts. Breadboards are made by different manufacturers, so the voltages they can handle depends on how they are constructed. How Does Current Flow in a Breadboard?The vertical columns of the breadboard are called terminals, while the horizontal long rows are called power rails because they are mostly used to connect the power supply to the breadboard. The positive rails are indicated by red lines, while the negative rails are indicated by black ones. That means our electric current, which is made up of moving charges, flows out of the positive side of the battery, through the wire and into the breadboard power bus. It then flows out of the black wire and into the second power bus, through the power bus and back to the negative side of the battery. How Many Amps Can a Breadboard Take?Due to the temporary nature of the contacts, most breadboard has a current limit of one amp or less. Breadboard generally cannot handle frequencies greater than ten megahertz because of the nature of the contacts, which create a stray capacitance of around two to twenty picofarads (pFs) for every connection.
kynix On 2021-08-06   4363
Resistors

What Ballat Resistors are Used for ?

CatalogⅠ What is a Ballast Resistor ?Ⅱ Types of Ballast Resistors2.1 Fixed Resistors2.2 Self-Variable ResistorsⅢ The Working Principle of  Ballast ResistorsⅣ Ballast Resistor – Uses and Applications4.1 Ballast Resistor in Fluorescent Lamps4.2 Ballast Resistor for Automotive Applications4.3 Ballast Resistor in a LED CircuitⅤ Symptons of Failture Ballast-ResistorⅥ Frequently Asked Questions about Ballast resistors Introduction  “Ballast” is generally considered as “something that provides stability in English dictionary.  ” Thus, when we refer to an electrical ballast, we are referring to an electrical device that is important in maintaining the stability of the electrical circuit. However, you might be wondering how it provides stability. Depending on the circuit in which they are used, some electric ballasts limit current while others limit voltage. By doing so, they reduce the risk of overvoltage or overcurrent in the circuit, thereby improving system stability. The complexity of electric ballast varies greatly. It can be as simple as a resistor, capacitor, inductor, or a combination of these, or as complex as the electronic ballast found in fluorescent lamps.  Ⅰ What is a Ballast Resistor ? A ballast resistor is an electronic component that is usually used to regulate the current in a circuit. Some devices, such as fluorescent lamps, can exhibit negative resistance characteristics, and an increase in current will result in a decrease in voltage. Negative resistance can cause damage to the power supply or equipment. Ballast resistors are usually connected in series with the negative load, taking advantage of the fact that all components in the series circuit receive the same current. Some ballasts are just series resistors, while others use capacitors and more complex components. Figure1: complex components Ⅱ Types of Ballast ResistorsA resistor is a current-limiting electronic component that can reduce circuit voltage and current. Ballast resistors are classified into three types: fixed, variable, and reactive.2.1 Fixed ResistorsThis genre of ballast resistors have a fixed resistance. A high resistance value is primarily taken considered for most applications. This genre of ballast resistor is commonly used in simple circuits with low-powered loads such as neon or LED lamps. This fixed resistor is also applied to control the ventilation fan speed. It employs a fixed ballast resistor with two center taps. The fan speed selector switch detours portions of the ballast. Therefore, the entire ballast resistor is suitable for full speed, while no section of the ballast resistor is suitable for the low speed.2.2 Self-Variable ResistorsThese ballast resistors have the property of resistance in response to changes in current, such as an increase in current increasing resistance and a decrease in current decreasing resistance. Incandescent lamps frequently use these ballast resistors. As the current through the lamp increases, the ballast resistor heats up, and the resistance rises with the temperature, as does the voltage drop across the resistor. When the current is down, the temperature of the ballast resistor decreases as well, as does its resistance and thus the voltage drop. The benefits of using this type of ballast resistor are that it provides more precise current control than a suitable fixed resistor. Another benefit is that the power lost in the resistive ballast is decreased because a smaller section of the overall power is lost in the ballast when compared to a fixed resistor. Ⅲ The Working Principle of  Ballast Resistors When 220V 50HZ AC power is applied to the switch closed circuit, the current flows through the ballast, and the lamp filament starter heats the filament(The starter was turned off in the beginning. The gas arc discharge in the jumping bubble in the starter caused the bimetallic sheet to heat and deform due to the application of an AC voltage greater than 190V, and the two electrodes were close together to form the filament heated by the passage.) Because there is no arc discharge when the two electrodes of the starter are close together, the bimetal cools and the two poles separate. As the ballast is inductive, when the circuit is suddenly interrupted, 600V is generated at both ends of the lamp for about 1ms. The pulse voltage is -1500V; the exact voltage value depends on the type of lamp. When the lamp discharges, the voltage at both ends drops immediately. At this point, the ballast limits the lamp current on the one hand while also supplying power on the other. There is a phase difference of 55° to 65° between the voltage and the working current of the lamp in order to keep the secondary starting voltage of the lamp stable.Figure2:  the working principle of  a ballast resistor Due to its simple structure, inductive ballast, as the first type of ballast to work with fluorescent lamps, has a relatively large market share. However, on account of its low power factor, poor low-voltage startup performance, heavy energy consumption, stroboscopic and many other shortcomings , its market is gradually being replaced by electronic ballasts. The energy consumption of inductive ballasts: 40W (lamp tube power) + 10W (inductive ballast self-heating consumption) is equal to the total power 50W consumption of the whole set of lamps and lanterns. An electronic ballast is a converter that converts low frequency alternating current power to high frequency alternating current power. Its basic operation is as follows: after passing through a radio frequency interference (RFI) filter, full-wave rectification, and a passive (or active) power factor corrector (PPFC or APFC), the industrial frequency power supply becomes a DC power supply. The output of high-frequency AC power of 20K-100KHZ is added to the LC series resonant circuit connected to the lamp via the DC/AC converter to heat the filament, but the lamp is "discharged" into the "on" state and then enters the light-emitting state. At this point, the high-frequency inductor limits the current increase, ensuring that the lamp tube receives the voltage and current required for normal operation. Various protection circuits, such as abnormal protection, surge voltage, and current protection, temperature protection, and so on, are frequently constructed to improve reliability. Ⅳ Ballast Resistor – Uses and Applications Ballast resistors are most commonly used to adjust the current to a negative resistance load. They can also be applied in other contexts. Fixed ballast resistors are common in low-power devices like light-emitting diodes (LEDs) and neon lights. LEDs are a positive resistive load that can benefit from ballast resistors. 4.1 Ballast Resistor in Fluorescent Lamps Fluorescent lighting, as we all know, is a popular and efficient lighting system. However, there is a disadvantage to using this type of lighting system. When directly connected to a voltage source, it heats up very quickly. This situation is due to the lamp's uncontrollable current draw as soon as its operation. A ballast resistor, connected in series with the lamp, is applied to the circuit to prevent overheating caused by excessive current draw. Therefore, the function of ballast resistor is to regulates the current and reduces the voltage. However,  for the lamp to light up, an arc has to be formed between its two electrodes. This necessitates a high starting voltage that is nearly equal to the supply voltage. The ballast resistor provides the required voltage during startup, and then immediately after an arc is established, it reduces the voltage while also regulating the current flow. Figure3: application in fluorescent lamp 4.2 Ballast Resistor for Automotive Applications Ballast resistors are generally included in the ignition kits of automotive machines such as automobile engines. Such devices are often called Ignition Ballast Resistors because of their application. The application of this device reduces the possibility of coil failure. It is connected between the ignition coil's primary voltage source and the coil stud. This connection helps to reduce the coil voltage and coil current, so the coil does not get as hot as it would without it, extending the coil's life. However, a high voltage equal to the primary voltage source is required to start the ignition engine. As a result, a jumper wire is frequently connected to the ballast resistor. This jumper wire provides the voltage required to start the engine.  Figure4: application in automotives 4.3 Ballast Resistor in a LED Circuit If the source voltage in an LED circuit is greater than the rated voltage of an LED lamp, the LED may be damaged. It is strongly advised to connect a ballast resistor in series with the lamp to avoid this case. By connecting the ballast resistor in this manner, the voltage across the LED is down to a tolerable level. The circuit diagram for the same is shown in the figure below.  Figure5: application in leds  The following formula is the value of resistance of the ballast :R = (E – Vf)/IFWhere: R= resistance of the ballast resistorE = voltage sourceVf = forward voltage of the LEDIF =Forward current of the LED. So, let's say you have an LED with a voltage rating of 4 volts, a forward current of 10 mA, and a voltage source of 6 volts. This means that the voltage across the LED should be 4 or less than 4 volts. As a result, the resistance of the ballast resistor should be R= (6-4)/0.010 = 200 or greater. Now that we've covered the applications briefly, let's look at the different types of ballast resistors on the market. Ⅴ Symptons of Failture Ballast-Resistor A ballast resistor is a device in your car that limits the amount of current flowing through an electric circuit. Because they did not have the benefit of circuit boards like most modern vehicles, ballast resistors are commonly found in older vehicles. Normal wear and tear can damage the ballast resistor over time, so there are a few things to look for if you suspect a bad or failing ballast resistor needs servicing. 1. Vehicle starts, then immediately goes out The most obvious symptom is that the vehicle starts but then dies as soon as you remove the key. If this occurs, Your Mechanic's experts will be able to measure the voltage coming from the ballast resistor and determine if it needs to be replaced. They will inform you of the condition of your ballast resistor once they have read the voltage. 2. Not starting at all The vehicle will not start if the ballast resistor is not functioning properly. Because it is an electrical system, it is best left to the professionals. The only way to get the vehicle running again is to replace the ballast resistor. 3.  Don’t jump the resistor Some people attempt to jump the resistor, which means that the ballast resistor is ignored and the extra current is routed to the points. The points are not designed to withstand the additional voltage, causing them to wear out and fail prematurely. This will result in a much more extensive repair than if the ballast resistor was replaced at the start. Furthermore, because you are tampering with electricity, it can be dangerous, especially if you don't know what you're doing. 4.  Let the vehicle beIf your ballast resistor is out of work, your vehicle will not start and you will need to have it towed to a mechanic's shop. Because the professionals at Your Mechanic make house calls, you will be able to save money on towing. Furthermore, because the vehicle will not start, it is not a dangerous situation as long as you leave it alone. Do not attempt to bypass the ballast resistor and do not continue to try to start the engine. Allow the professionals to repair it so you can get back on your way. Ⅵ Frequently Asked Questions about Ballast resistors 1. Is a ballast resistor necessary? If the coil required a ballast resistor when it was used with points, then you must still use the resistor. If it didn't, then no resistor is necessary. The ballast resistor keeps the engine running by preventing the engine from receiving full amperage from the ignition once started.  2. Why do ignition coils need ballast resistor? In simple terms, the ballast resistor in a Mopar limits the amperage, or current flow, through the coil while the engine is running, thereby extending the life of the coil and breaker points of the distributor. 3. How do you know if a ballast resistor is bad?To test your ballast resistor you need an ohm meter or multimeter set to ohms. Remove the connectors from both sides of the resistor. The ohms should read between 1.8 and 5 ohms. You should be getting 9 volts to the positive side of the coil. 4. What causes a ballast resistor to fail?The resistance through the ballast resistor varies with current flow which varies with engine rpm. This naturally causes the resistor to expand and contract from heat. That's why they eventually fail. 5. Can a resistor wire go bad?  The only way the wire will "go bad" is if it gets a break in it so it has infinite resistance (an open circuit). 6. Which circuit the ballast resistor is used?  Ballasts can also be used simply to limit the current in an ordinary, positive-resistance circuit. Prior to the advent of solid-state ignition, automobile ignition systems commonly included a ballast resistor to regulate the voltage applied to the ignition system. 7. What is inside of a ballast? A magnetic ballast (also called a choke) contains a coil of copper wire. The magnetic field produced by the wire traps most of the current so only the right amount gets through to the fluorescent light. That amount can fluctuate depending on the thickness and length of the copper wire. 8. What's the difference between a ballast and non ballast coil? Basically, a non-ballast coil is designed to produce full spark output with 12 volts on the input (+ terminal). A ballast coil is designed to produce the same spark output, but with only 6 to 9 volts on the input. 
kynix On 2021-08-03   7119
Resistors

The Best Tech Guide to Laser Diodes in 2021

What is a Laser Diode?A laser diode (injection laser diode, or diode laser) is a semiconductor device that can generate laser light, emitting a narrow light containing a single color, which is similar to a light-emitting diode (LED). The three conditions for generating laser light are: achieving particle number inversion, meeting threshold conditions and resonance conditions. Since laser diodes are extremely electrostatic sensitive, they should be used with care to prevent static electricity. They can be divided into homojunction laser, single heterojunction (SH) laser, double heterojunction (DH) laser and quantum well (QW) laser according to the different PN junction materials.Topics Covered in this GuideLaser Diode Tech Guide in 2021What is a Laser Diode?Laser Diode SpecificationsLaser Diode CharacteristicsLaser Diode ApplicationsHow Does a Laser Diode Work?What is the Laser Diode Symbol?What are the types of Laser Diode?Laser Diode Using TipsHow to Test a Laser Diode?How to Make a Laser Diode?How to Power a Laser Diode?How to Build a Laser Diode Driver Circuit?How to Wire a Laser Diode?How to Select the Right Laser Diode?How to Drive Pulse Laser Diode?What is Power Source of 532 Laser Diode?What is the Difference between Laser Diode(LD) and LED?What is the Wavelength Range of a Laser Diode?Is Diode Laser Permanent?Is LED a Laser Light?How Long do Diode Lasers Last?Can an LED be Used as a Laser?What are the Advantages of Using Laser Diode Instead of an LED?What is the Disadvantage of Laser?FAQsLaser Diode Specifications(1) Wavelength– It is the laser tube working wavelength, including 635nm, 650nm, 670nm, 690nm, 780nm, 810nm, 860nm, 980nm, etc, used for photoelectric switch laser.(2) Threshold Current– The current at which the laser tube starts to generate laser oscillation. For general low-power laser tubes, the value is about tens of mA, and the threshold current of laser tubes with multi-quantum well structure can be as low as 10mA or less.(3) Operating Current– It is the drive current that laser tube to achieve the rated output power, which is more important for the design and commissioning of the laser drive circuit.(4) Vertical Divergence Angle– It is the open angle that the laser diode's light-emitting band in the direction of the vertical PN junction, generally in the 15˚ ~ 40˚ or so.(5) Horizontal Divergence Angle– It is open angle that the laser diode's light-emitting band in the parallel direction with the PN junction, generally in 6˚ ~ 10˚ or so.(6) Monitoring Current– It is the current flowing on the PIN tube when the laser tube is at rated output power. Laser Diode CharacteristicsThe basic structure of the semiconductor laser diode is shown in the figure. A pair of parallel planes perpendicular to the PN junction surface form the Fabry-Perot resonant cavity, they can be the solution surface of the semiconductor crystal, but also can be polished plane. The remaining two sides are relatively rough to eliminate the laser action in other directions than the main direction. In addition, lasers consist of three main components: a lasing medium (solid, liquid or gas), a stimulating energy source (pump) and an optical resonator.Figure 1. Semiconductor Laser Diode StructureOne of the characteristics of laser diodes is the ability to modulate the intensity of their output light directly from current. Because the relationship between output optical power and input current is mostly linear, laser diodes can use analog or digital current to directly modulate the output light intensity, no need for expensive modulators, which makes the diode more economical to use.The most important characteristic of a diode is its unidirectional conductivity, and laser diodes, as one of the diode types, have the same features. In a circuit, current can only flow in from the positive terminal of the diode and out from the negative terminal. The following are specific descriptions.1) Forward FeatureIn electronic circuits, the diode conducts when the positive terminal of the diode is connected to the high potential terminal and the negative terminal to the low potential terminal. In terms of this connection, it called forward bias. In addition, when the forward voltage applied to both ends of the diode is very small, the diode still cannot conduct and the forward current flowing through is very small. Only when the forward voltage reaches a certain value (this value is called the "threshold voltage", about 0.2V for germanium tubes and 0.6V for silicon tubes), the diode can conduct. After it, the voltage across the diode remains basically unchanged (about 0.3V for germanium and 0.7V for silicon diode), which is called the "forward voltage drop".2) Reverse FeatureIn electronic circuits, the positive terminal of the diode is connected to the low potential terminal, and the negative terminal is connected to the high potential terminal. When there is almost no current flowing through the tube, the diode is in the cutoff state. This connection called reverse bias. Diode in reverse bias, there will still be a weak reverse current flow through, called leakage current. When the reverse voltage across the diode increases to a certain value, the reverse current will increase sharply, the diode will lose its unidirectional conductive characteristics, this state is called diode breakdown. Laser diode injection current must be greater than the critical current density, which is related to the temperature of the contact surface and indirectly affects the tube performance, to meet the residence reversal conditions and emit laser. When operating at high temperatures, the critical current increases, reducing efficiency and even damaging the component. Laser Diode ApplicationsAs the most common type of laser products, laser diodes have the advantages of high efficiency, small size and long life, but their low output power (generally less than 2mW), poor linearity and monochromaticity are not good for cable TV system applications, because they cannot transmit multi-channel and high-performance analog signals. Based on the advantages of laser diodes, they play a important role in many applications areas. For example, in the return module of bi-directional optical receivers, uplink transmission generally uses quantum well laser diodes as the light source. Also it is widely used in the computer on the CD-ROM drive, laser printer in the print head, bar code scanner, laser ranging, laser medical, optical communications, laser indication and other small power optoelectronic equipment. The lighting, laser surgery, laser welding and laser weapons and other high-power equipment have laser diodes too.Compared with LEDs, With different light source, lasers are more powerful and operate at faster speeds than LEDs, and they can also transmit light farther with fewer errors. They are also much more expensive than LEDs.Figure 2. Laser DiodeHow Does a Laser Diode Work?Light Emitting PrincipleLight emission in semiconductors is usually caused by carrier complexation. When a positive voltage is applied to the PN junction, it will weaken the PN junction barrier, forcing electrons to be injected into the P region from the N region, and holes to be injected into the N region from the P region. These non-equilibrium electrons and holes injected near the PN junction will be compounded, thus emitting photons of wavelength λ with the following equation.λ=hc/EgWhere: h - Planck's constant, c - speed of light, Eg - band gap width of the semiconductor.The above luminescence phenomenon due to the spontaneous compounding of electrons and holes is called spontaneous radiation. When the spontaneous radiation generated by the photon through the semiconductor, once the electron-hole pair has been emitted near, it can excite the two composite to generate new photons. This photon has been induced to excite the carrier compound and issued a new photon known as excited radiation.If the injection current is large enough, a carrier distribution opposite to the thermal equilibrium state will be formed, that is, the particle number reversal. When the carrier within the active layer in the case of a large number of inversion, a small amount of spontaneous radiation generated by the photons due to the resonant cavity two end reflect and then have induction radiation, resulting in frequency-selective resonance positive feedback, or a gain for a frequency. When the gain is greater than the absorption loss, a coherent light with good spectral lines can be issued from the PN junction, that is, the laser.How Laser Diodes Work?As for Laser diode light-emitting principle, the P-N junction in a laser diode is formed by two doped GaAs layers. It has two flat-ended structures, parallel to a end (highly reflective surface) and a partial reflection. Laser diodes emit coherent light in which all the waves are at the same frequency and phase. The wavelength of the light to be emitted is exactly related to the length of the junction. When the P-N junction is forward biased by an external voltage, the electrons move through the junction and recombine as in a normal diode. When the electrons are compounded with holes, photons are released. These photons hit the atoms, causing more photons to be released. As the forward bias current increases, more electrons enter the depletion region and cause more photons to be emitted. Eventually, some of the photons randomly drifting in the depletion region strike the reflecting surface vertically, thus reflecting back along their original path. The reflected photons are again reflected back from the other end of the junction. This movement of photons from one end to the other is continuous several times. During the photon motion, more atoms release more photons due to the avalanche effect. This process of reflection and production of more and more photons produces a very intense laser beam.Each photon produced in the emission process explained above is identical to the other photons in terms of energy level, phase relationship and frequency. Thus, the emission process gives a laser beam of a single wavelength. To produce a laser beam, the current in the laser diode must be made to exceed a certain threshold level. Currents below the threshold level force the diode to behave as an LED, emitting incoherent light. What is the Laser Diode Symbol?The laser diode symbol used is often the same one used for light emitting diodes in circuit diagrams. It uses the basic semiconductor diode symbol with arrows indicating the generation and emanation of light.Figure 3. Laser Diode Symbol What are the types of Laser Diode?There are several types of laser diodes:✔️Quantum well lasers✔️Quantum cascade lasers✔️External-cavity diode lasers✔️Interband cascade lasers✔️Separate confinement heterostructure lasers✔️DHL (double heterostructure lasers)✔️DFB-LD (distributed feedback laser diode)✔️DBR-LD (distributed bragg reflector laser)✔️FBG (FBG laser diodes laser diodes)✔️VCSEL ( vertical-cavity surface-emitting laser)✔️VECSEL(vertical-external-cavity surface-emitting-laser)✔️MOEMS-LD (micro-opto-electro-mechanical systems laser diode) Laser Diode Using Tips1) laser diode emitted laser light may cause harm to the human eyes. When using, don’t directly watch the light source. It requires warning signs.2) The device needs a suitable drive power supply, the instantaneous reverse current should not exceed 2uA, and the reverse voltage should not exceed 3V. In the power supply on and off, to prevent inrush current. When testing the drive circuit with an oscilloscope, disconnect the power supply and then connect the oscilloscope probe, if the probe is tested under power on, the inrush current may damage the device.3) The device should be stored or worked in a clean environment.4) Working at higher temperatures will increase the threshold current, lower conversion frequency and accelerate the aging of the device. When adjusting the amount of light input, use the optical power meter to detect to prevent exceeding the large rated output.5) The output power works higher than the specified parameters, which will accelerate the aging of the components.The following measures can be taken to slow down device aging.    a. Driving the laser diode with a DC constant current source.    b. Connect a current limiting resistor in series with a bypass capacitor to the laser diode circuit.    c. Since an increase in the temperature of the laser diode will increase the current flowing through it, the heat dissipation measures must be applied to ensure that the device operates within a certain temperature range.(4) To avoid the laser diode breakdown due to withstand excessive reverse voltage, it can be connected in reverse parallel on both ends of the fast silicon diode.(6) The machine needs to be fully dissipated or used under cooling conditions to prevent high temperature use. The output wavelength of the laser is affected by the operating current and heat dissipation, to maintain good heat dissipation conditions and reduce the temperature of the tube core when working.7) Diodes are electrostatic sensitive devices, to take appropriate anti-static measures.Figure 4. Injection Laser DiodeHow to Test a Laser Diode?a. Resistance measurement methodRemove the laser diode, use a multimeter R × 1k or R × 10k file to measure its positive and negative resistances. If normal, the forward resistance value is between 20~40kΩ, and the reverse resistance value is ∞ (infinity). If the measured forward resistance value has exceeded 50kΩ, it means that the performance of the laser diode has declined. If the measured forward resistance value is greater than 90kΩ, it means that the diode has been seriously aged, can no longer be used.b. Current measurement methodUse a multimeter to measure the voltage drop across the load resistor in the laser diode drive circuit, and then estimate the current value flowing through the tube according to Ohm's law. When the current exceeds 100mA, if the laser power potentiometer is adjusted, and no significant change in current, the laser diode can be judged to be seriously aged. If the current increases sharply and out of control, it means that the optical resonant cavity of the laser diode has been damaged.c. Pins DetectionThe laser diode has three pins: LD transmitter, PD receiver, LD-N common1) To distinguish between LD and PD. Use R × 1k block to measure the resistances of laser diode three pins. If a resistance value between the two pins reaches a few thousand ohms, at this time, the black pen is connected to the end of the PD anode, the red pen is connected to the pin for the common terminal, the remaining pin for the LD cathode, so as to distinguish the PD part (bc part of the figure) and LD part ( This distinguishes the PD part (bc part of the figure) and the LD part (ab part of the figure).2) Detect the PD part. PD part of the laser diode is essentially a photosensitive diode, using a multimeter test method is as follows: R × 1k block to measure its resistance, if the forward resistance of a few thousand ohms, the reverse resistance is infinite, it initially indicates that the PD part is good. If the forward resistance is 0 or infinity, it shows that the PD part has been bad. If the reverse resistance is not infinity, it means that the PD part has reverse leakage and the tube quality has become poor.3) Detect the LD part. Use the multimeter R × 1k block to measure the forward resistance of the LD part, that is, the black pen connected to the common terminal b, red pen connected to the a, the forward resistance should be between 10kΩ ~ 30kΩ, the reverse resistance should be infinity. If the measured forward resistance value is greater than 55kΩ, the reverse resistance value of 100kΩ or less, indicating that the LD part has been seriously aging, so the use of the effect will become worse. How to Make a Laser Diode?Step 1: Before made a laser diode, you should clear somethings firstly, including safety equipment, procedures, training in place, as well as disposal etc. Step 2: Build a working laser yourself you start with buying the diode. then you need a lens , and a heat sink , and a powersupply that won't blow it (they're very sensitive) .... all these components are on online, and that's quiet a tricky job ...much easier and cheaper to buy an assembled laser.Step 3: Spend a couple of pounds to purchase a laser pointer, and pull the diode & circuit out of that.Step 4: Don't power it up when it's direction is not firmly fixed away from your eyes, from anyone's eyes , and there might be reflective surfaces on the beam path nearby. Pay attention, do it legally where you are. How to Power a Laser Diode?Laser diodes are operated in forward conduction mode within a specified current range that is optimal for lasing operation, because they are current-driven devices. Laser diode power supplies can operate in one of two modes, constant current (CC) and automatic power control (APC). Most, but certainly not all, smaller laser diodes (5.6- and 9-mm packages) are operated in APC mode. For APC operation, the power supply must have a photodiode mounted inside the laser diode package. How to Build a Laser Diode Driver Circuit?Firstly, you should know that a laser diode driver circuit is a circuit which is used to limit the current and then supplies to the laser diode, and then follow the below steps:Step 1: Have a project with laser diode.Step 2: Find out all the useful parts and their parameters from your project.Step 3. Build the circuits according to the related project schematic.Step 4. Connect the Laser Diode and test it. How to Wire a Laser Diode?According to unidirectional conductivity, laser diodes only allow current to flow in one direction, and they're always polarized. First look at the positive and negative poles of the diode, and then the positive potential is connected to the anode of the diode, and the negative potential is connected to the cathode of the diode. How to Select the Right Laser Diode?Choose a laser diode for your application according to the following steps:Step 1: Turn application requirements into laser parametersStep 2: Selecting the laser typeStep 3: Selecting the laser materialStep 4: Make your final chart and go searching How to Drive Pulse Laser Diode?Laser Diode Driver is to provide current to the laser diode. With the amount of current controlled by the user or some automatic apparatus, you can drive a pulse laser diode. In addition, a laser driver can only regulate the current as long as the laser voltage stays within certain limits, so you should have a check the circuit parameters to select a proper diode driver. What is Power Source of 532 Laser Diode?Check the following table to find out the power source of 532 laser diode:532nm Green Laser DiodePowerPackageDescription0.004WTO-Can- Integrated Photodiode- Compact Size0.005WTurn-Key Module- Compact Size- Long Lifetime0.01WTurn-Key Module- Fiber-Coupled Output- Integrated Photodiode0.1WTO-Can- Integrated Photodiode- Compact Size0.2WTO-Can- Integrated Photodiode- Mode-Hop Supression0.4WButterfly- Integrated Photodiode- Integrated Heater0.5WButterfly- Internal Heater- Integrated PhotodiodeWhat is the Difference between Laser Diode(LD) and LED?LDs and LEDs both emit photons to produce light, but both of them have many differences according to the following table:ParametersLDLEDWorking PrincipleStimulated emissionSpontaneous emissionOmnidirectional emissionFull FormLight Amplification by Stimulated Emission of RadiationLight Emitting DiodeResponseFast response in comparison to LEDSlow responseDriving CurrentRanges from 5 to 40mARanges from 50 to 100mANature of Emitted LightCoherent and MonochromaticIncoherent and consists of various colors.Junction Area during ManufacturingNarrow and small JunctionWide Junction AreaBandwidth RangeRanges from 1MHz to 2MHZRange from10 to 50THzPower to light Conversion EfficiencyApprox 70 %Approx 30%Numerical Aperture of the obtained Light BeamExtremely low as compared to LEDs.Higher in LEDsCostHigh cost and thus used in the specific application.Low cost and thus economicalWhat is the Wavelength Range of a Laser Diode?Diode lasers deliver wavelengths ranging from 810 to 1064 nm. Diode lasers are compact and portable solid-state units. They are used strictly for soft tissue procedures and penetrate 2 to 3 mm or more into soft tissue, depending on the wavelength and tissue biotype. Is Diode Laser Permanent?Diode lasers use a single wavelength of light that has a high abruption rate in melanin. As the melanin heats up it destroys the root and blood flow to the follicle disabling the hair growth permanently. ... Diode lasers deliver high frequency, low fluence pulses and can be safely used on all skin types. Is LED a Laser Light?LEDs typically last longer than lasers, while lasers are faster. ... LEDs have a higher output with wider bandwidths, meaning that they can produce a broad range of less-concentrated light. Lasers have a lesser output and a small bandwidth, produced with a tiny pinpoint of light. How Long do Diode Lasers Last?Typical lifetime of laser diode modules are 25,000 to 50,000 hours. If the laser diode temperature continues to rise exceeding the maximum operating temperature, the diode can be catastrophically damaged or the long term performance may degrade significantly. Can an LED be Used as a Laser?The LED and laser emit light in a relatively narrow range of wavelengths. However, lasers put all their energy in a single wavelength, which emits from a tiny spot. LEDs spread the energy over more wavelengths and send that light from a larger spot into wide cone. What are the Advantages of Using Laser Diode Instead of an LED?It produces a very intense beam of light or infrared radiation which is having following properties. Laser diode used in optical fiber systems are made of gallium arsenide phosphide. The laser having size of grain of sand can produce power output of about 10 mWatt. ON/OFF switching speed of laser is faster than LED. What is the Disadvantage of Laser?Following are the drawbacks or disadvantages of Laser:It is expensive and hence more expenditure to the patients requiring laser based treatments.It is costly to maintain and hence more cost to doctors and hospital management. Increases complexity and duration of the treatment based on laser devices or equipments. FAQs1. Why do we prefer GaAs for laser diode?GaAs advantagesGaAs devices are relatively insensitive to overheating, owing to their wider energy band gap, and they also tend to create less noise (disturbance in an electrical signal) in electronic circuits than silicon devices, especially at high frequencies. 2. What is the advantage of laser over LED?The output power of a 1 watt LED can be < 100 milliwatts. Besides dramatic differences in total output, the laser also offers a significant advantage in terms of how usable that power is to the optical system. Specifically, the laser is a point source of coherent light that produces a well-behaved beam. 3. Why is laser light monochromatic?Monochromatic Laser LightThe light from a laser typically comes from one atomic transition with a single precise wavelength. So the laser light has a single spectral color and is almost the purest monochromatic light available. 4. What happens if the laser diode is forward biased?Forward bias injects charges into the junction, causing spontaneous emission of photons. When the diode is forward-biased, charges are injected into the active area of the junction, while electrons and holes recombine in the junction, creating spontaneous emission of photons. 5. Is a laser diode an LED?Light-emitting diodes (LEDs), like laser diodes, generate radiation via electrical current injection into a junction. LED light comes from spontaneous emission, whereas laser diode light arises from stimulated emission. Thus, LEDs generally have lower output powers and omnidirectional emission.
kynix On 2021-08-03   4053

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Follow us

Join our mailing list!

Be the first to know about new products, special offers, and more.

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.