ic Related Articles
Stay Ahead with Expert Electronics Insights,
Industry Trends, and Innovative Tips
- Electronic Components
- News Room
- General electronic semiconductor
- Components Guide
- Sort by
- Robots
- Transmitters
- Capacitors
- IC Chips
- PCBs
- Connectors
- Amplifiers
- Memory
- LED
- Diodes
- Transistors
- Battery
- Oscillators
- Resistors
- Transceiver
- RFID
- FPGA
- Mosfets
- Sensor
- Motors, Solenoids, Driver Boards/Modules
- Relays
- Optoelectronics
- Power
- Transformer
- Fuse
- Thyristor
- potentiometer
- Development Boards
- RF/IF
- Semiconductor Information
- Sensors
- PCB
- transistor
ⅠIntroduction Motor capacitors temporarily store an electrical charge to provide additional torque and improve the performance and efficiency of a motor. Start capacitors provide added torque during motor startup and then exit the circuit when the motor reaches operating speed. Run capacitors assist the motor in maintaining a consistent charge while it is running. By balancing working power and supplied power, power factor correction capacitors reduce motor power consumption caused by heavy inductive loads. Motor capacitors are most frequently used to power motors in HVAC applications such as fans, blowers, and compressors, but they are also found in pumps, conveyors, and machine tools. What does a run capacitor look like? Catalog ⅠIntroduction Ⅱ Two Types of Motor Capacitor 2.1 What is the run capacitor? 2.2 What is the starter capacitor? Ⅲ Run Capacitor Related Video Ⅳ Specifications of Run Capacitor Ⅴ Faulty Run Capacitor 5.1 When Is It Time to Replace a Run Capacitor? 5.2 Causes of Failure Ⅵ How To Replace a Start Run Capacitor? Ⅶ How Do They Work In an HVAC System? Ⅷ Dual Capacitors vs. Run Capacitors vs. Run Capacitors Ⅱ Two Types of Motor Capacitor Motor capacitor include two types: run capacitor and starter capacitor. Let us have a look at the two capacitors. 2.1 What is the run capacitor? Run capacitors are rated in the 3–70 microfarad range (uF). Voltage classification is also applied to rate run capacitors. The voltage levels are 370V and 440V. Starting capacitors have ratings greater than 70 microfarads (uF). Run capacitors are designed for continuous duty and remain energized throughout the lasting of the motor's operation. A capacitor is required to power a second phase winding in a single-phase electric motor. This is why the sizing is so crucial. The motor will not have an even magnetic field if the incorrect run capacitor is installed.This case will lead to the rotor hesitating at uneven spots. This pause causes the motor to become noisy, increases energy consumption, reduces performance, and causes the motor to overheat. 2.2 What is the starter capacitor? In contrast to run capacitors, which have a specific uF rating, starting capacitors are housed in a black plastic case and have an uF range. Start capacitors (with ratings of 70 microfarads or higher) are classified into three voltage classes: 125V, 250V, and 330V. A 35 uF at 370V run capacitor and an 88–108 uF at 250V start capacitor are two examples. Start capacitors increase motor starting torque and allow a motor to be rapidly cycled on and off. Start capacitors are designed for one-time use only. Start capacitors are energized for a short time, allowing the motor to reach 3/4 of its full speed before being disconnected from the circuit. Ⅲ Run Capacitor Related Video Start Capacitors & Run Capacitors for Electric Motors - Differences Explained by TEMCo run capacitor video descriped: What's the difference between a start capacitor and a run capacitor? Can you use them interchangeably? See why these two types of capacitors cannot always be substituted for one another. Ⅳ Specifications of Run Capacitor Most run capacitor applications employ capacitance ratings of 2.5-100 uf (microfarads) and voltages of 370 or 440 VAC. They are also usually rated at 50 and 60 Hz. Cases are typically round or oval in shape, with a steel or aluminum shell and cap. Terminals are typically 14" push-on terminals with 2-4 terminals per connection post. Specifications of Run Capacitor Ⅴ Faulty Run Capacitor 5.1 When Is It Time to Replace a Run Capacitor? As a general rule, a run capacitor will greatly exceed the start capacitor of the same motor. A run motor capacitor will wear down at different levels, making it more complicated to determine if it needs to be replaced. When a run capacitor begins to perform outside of its allowable range, the rated capacitance value usually drops. A "tolerance" will be specified for most standard motor run capacitors, describing how close the actual value may be to the rated capacitance value. It is usually within +/- 5% to 10%. For most motors, as long as the actual value is within 10% of the rated value, you're good to go. A run capacitor will occasionally bulge from internal pressure due to a flaw in the capacitor's construction or a non-capacitor-related motor issue. Most modern run capacitor designs will open the circuit, disconnecting the internal spiral membrane as a precautionary measure to keep the capacitor from popping. The test is simple: it is time to replace in both cases that it is bulging and there is no continuity between the terminals, Run Capacitor 5.2 Causes of Failure Depending on how close the run capacitor is to its design life, there could be several reasons why it failed. Diagnosing and Replacing a Run Capacitor Ⅵ How To Replace a Start Run Capacitor? When a new motor is installed, a new fan capacitor should always be installed. It is always a good idea to photograph or write down the wire coloring and connections. Turn off the power to the HVAC unit and use a meter to ensure it is completely off.Locate and remove the side panel where the electricity is fed into the unit.Locate the Stat Run Capacitor; there will only be one in a Dual Run capacitor. If there are two, only the fan motor capacitor has to be replaced.Check the MFD and voltages, then connect the new connections from the old capacitor to the new capacitor one leg at a time to ensure they are correct. (For example, if you have two capacitors, one is for the compressor and the other is for the fan motor.) Ⅶ How Do They Work In an HVAC System? A Start or Run Capacitor can be combined into a single capacitor with three leads known as a Dual Capacitor, or it can be split between two separate capacitors. The Start Capacitor gives a fan motor the torque it needs to start spinning and then turns off, whereas the Run Capacitor stays on and provides extra torque to the motor when needed. The motor will most likely not start if the Start Capacitor fails. If a Run capacitor fails, the motor will start, but the running amperage will be higher than usual, causing the motor to run hot and have a short life expectancy. There are three connections on a Dual Capacitor: HERM, FAN, and COM. HERM is for the Hermetically Sealed Compressor, FAN is for the Condenser Fan Motor, and COM is for the Contactor, which powers the Capacitor. If the unit has two capacitors, the larger of the two is the Run Capacitor. Keep in mind that the compressor frequently necessitates the use of a HERM capacitor (compressor). Run Capacitor circuit Ⅷ Dual Capacitors vs. Run Capacitors vs. Run Capacitors The only benefit we can get from the dual-run capacitor design is that it comes in a small package with only three connections. Aside from that, there is no distinction between run and dual run capacitors. If there is enough space for mounting, it is acceptable to replace your original dual-run capacitor with two separate run capacitors. They typically have "C" connections for "common," "H" or "Herm" connections for "Hermetic Compressor," and "F" connections for "Fan." They'll also have two different capacitor ratings for the two parts. Start capacitors provide a high capacitance value required for motor starting in a very short (seconds) time. They are only designed for intermittent duty and will fail catastrophically if left on for an extended time. Run capacitors are continuous duty because they provide continuous voltage and current control to a motor's windings. They typically have a much lower capacitance value. Ⅸ FAQ 1. What happens when a run capacitor goes bad? A bad motor capacitor may cause starting problems or could shut off the motor while running. Same principle on the dirty coil. ... If a Run capacitor goes bad then a motor can turn on but the running amperage will be higher than normal causing the motor to run hot and have a short life expectancy. 2. What is the difference between a capacitor and a run capacitor? The start capacitor creates a current to voltage lag in the separate start windings of the motor. The current builds up slowly, and the armature has an opportunity to begin rotating with the field of current. A run capacitor uses the charge in the dielectric to boost the current which provides power to the motor. 3. Can I run my AC without a capacitor? Most of the motors in your air conditioner can't run without a good capacitor. Like I said, they support these motors. They help the motor start and run efficiently. Some people have gone out to their air conditioner and noticed the fan wasn't spinning on their AC as it should be. 4. Can I use a run capacitor in place of a start capacitor? The capacitance and voltage ratings would have to match the original start capacitor specification. A start capacitor can never be used as a run capacitor, because it cannot not handle current continuously. 5. Do I need a start or run capacitor? Run capacitors are designed for continuous duty, and are energized the entire time the motor is running. Single phase electric motors need a capacitor to energize a second phase winding. ... Start capacitors increase motor starting torque and allow a motor to be cycled on and off rapidly. 6. What size run capacitor do I need? The run capacitor should have the exact microfarad (uf) that the motor is rated for. Capacitors rated above 70uf are considered Start Capacitors and are generally removed from the circuit electrically during operation. This is where the rule of +/- 10% of the rating came from, for Start Capacitors ONLY!
kynix On 2021-11-12
IntroductionThe 1N4007 is a general-purpose silicon rectifier diode, typically found in a plastic DO-41 axial package. It is widely used in various AC-to-DC rectifier circuits, bridge rectifier circuits, and general-purpose power supply applications. The 1N4007 utilizes the unidirectional conductivity of the P-N junction to convert alternating current into pulsed direct current. Due to its high reverse voltage rating (1000V) and low cost, it is one of the most popular components in electronics.Ⅰ 1N4007 Diode Specifications1.1 Rectifier Diode OverviewThe 1N4007 is a standard recovery rectifier diode. In low-power/low-current scenarios, the forward voltage (Vf) is typically around 0.7V to 0.8V. However, under its full rated load (1A), the forward voltage drop can reach up to 1.1V.Note on Frequency: The reverse recovery time (Trr) of the 1N4007 is in the microsecond (μs) range (typically 2μs to 30μs depending on conditions). This classifies it as a "slow" diode, meaning it is suitable for 50Hz/60Hz mains rectification but not suitable for high-frequency switching circuits (like high-frequency DC-DC converters), where Fast Recovery (FR) or Ultra-Fast (UF) diodes are required.Rectifier diodes make full use of unidirectional conductivity. They block the negative half-cycle of an AC waveform to convert it into a pulsating DC signal. To smooth this output, they are usually used in combination with a capacitor. The diode is connected in series, and the capacitor is connected in parallel to the load.Figure 1. 1N4007 Bridge Rectifier Circuit Example1.2 Nomenclature: What does 1N4007 mean?"1": Represents the number of junctions. In JEDEC nomenclature, "1" stands for a component with one P-N junction (a diode)."N": Stands for semiconductor device, registered with the EIA (Electronic Industries Alliance) / JEDEC."4007": The specific registration number indicating the device's electrical characteristics within the 1N400x series.1.3 1N4007 Pins and SymbolPINDescription1 (Marked with Band)Cathode (-)2 (Unmarked)Anode (+)1.4 1N4007 Basic Parameters (at 25°C)Type: Standard Recovery Silicon RectifierMax Average Forward Rectified Current (Io): 1.0 APeak Forward Surge Current (Ifsm): 30 A (for 8.3ms single half-sine-wave)Max Repetitive Peak Reverse Voltage (Vrrm): 1000 VMax DC Blocking Voltage: 1000 VMax Forward Voltage Drop (Vf): 1.1 V (at 1.0A current)Max Reverse Leakage Current (Ir): 5 μA (at rated DC blocking voltage)Typical Junction Capacitance (Cj): 15 pF (measured at 4V, 1MHz)Typical Thermal Resistance: 65 °C/W (Junction to Ambient)Operating Temperature Range: -55°C to +150°CFigure 2. Forward Current Derating Curve1.5 1N4007 FeaturesLow reverse leakage currentHigh surge current capability (up to 30A non-repetitive)RoHS compliant and available in Pb-Free packagesHigh-temperature soldering guaranteed: 260°C/10 seconds.Mechanical Data:Case: DO-41 Molded PlasticTerminals: Plated axial leads, solderable per MIL-STD-202Polarity: Color band denotes cathode endⅡ 1N4001-1N4007 Series ComparisonThe 1N400x series contains diodes that are physically identical and rated for the same current (1A). The only difference is the Maximum Repetitive Reverse Voltage (Vrrm). Because the 1N4007 has the highest voltage rating (1000V), it can replace any other diode in the series (1N4001 through 1N4006).ModelCurrent (A)Max Peak Reverse Voltage (V)Max RMS Voltage (V)1N4001150351N40021100701N400312001401N400414002801N400516004201N400618005601N400711000700Ⅲ Alternative Models & EquivalentsThe 1N4007 can often be replaced by higher-spec diodes.Higher Current: 1N5399 (1.5A) and 1N5408 (3.0A). Note: The 1N5408 has thicker leads and a larger body (DO-201AD) and may not fit all PCB holes designed for the 1N4007.Fast Recovery: If high-frequency performance is required, FR107 (Fast Recovery) or UF4007 (Ultra Fast) are excellent replacements. They share the same voltage/current ratings but switch off much faster.Schottky Diodes (Caution): While Schottky diodes like 1N5819 or 1N5818 have a lower forward voltage drop (higher efficiency), they usually have much lower reverse voltage ratings (often 20V-40V). Do not replace a 1N4007 with a Schottky diode in high-voltage circuits (like 110V/220V mains) or the diode will fail instantly. However, for low voltage (e.g., 12V) DC inputs, a Schottky like the SB1100 (100V) can be a more efficient substitute.ModelMax Reverse Voltage (V)Avg Rectified Current (A)Max Surge Current (A)Max Reverse Leakage (μA)1N4007100013051N539910001.55051N5408100032005FR10710001305 (Fast Recovery)Ⅳ 1N4007 vs. M7 (SMD Versions)When moving from Through-Hole Technology (THT) to Surface Mount Technology (SMT), the electrical equivalents of the 1N4007 are identified by different package codes.1N4007: This specifically refers to the DO-41 axial lead package (through-hole).M7: This is the SMA (DO-214AC) surface mount version of the 1N4007. It is electrically identical (1A, 1000V).A7: This is the SOD-123 surface mount version. It is smaller than the SMA package but carries similar specs (usually slightly lower thermal dissipation).SM4007: This generally refers to the MELF (DO-213AB) cylindrical surface mount package, though "SM4007" is sometimes used generically for any SMD version.Figure 3. DO-41 Package (1N4007)Summary: If you see a diode marked "M7" on a circuit board, it is a surface-mount 1N4007.Ⅴ 1N4007 Application Examples5.1 Solving Auxiliary Winding OvervoltageThe slow recovery characteristics of the 1N4007 can sometimes be advantageous over faster diodes in specific power supply applications.In Flyback power supplies, multi-output transformers can suffer from poor cross-regulation. A common issue is the VCC auxiliary winding voltage rising too high, triggering the IC's Over-Voltage Protection (OVP). This often happens because a fast diode (like the HER107) rectifies the high-frequency leakage inductance spike (the "ringing") at the leading edge of the waveform, rather than just the plateau voltage.Figure 4. IC Control CircuitSolution: By replacing the fast HER107 with a standard speed 1N4007, the slower turn-on time ignores the initial high-frequency spike. This effectively filters the peak voltage, lowering the average VCC voltage seen by the IC and preventing false OVP triggering.5.2 RCD Snubber EMI SuppressionIn RCD (Resistor-Capacitor-Diode) snubber circuits used to protect MOSFETs in Flyback converters, using a slow diode like the 1N4007 can help improve Electro-Magnetic Interference (EMI).Figure 5. RCD Absorption CircuitHow it works: A "fast" diode snaps off very quickly, which can induce high-frequency ringing. The 1N4007 takes longer to recover (reverse recovery). During this brief recovery period, a small amount of reverse current flows back. This "soft recovery" acts as a dampener, absorbing some of the oscillation energy and reducing the voltage stress and EMI radiation on the MOSFET drain.Trade-off: The downside is that the 1N4007 will generate more heat due to reverse recovery losses. This technique is generally suitable for lower-power adapters (<20W) where EMI is a priority and thermal overhead is available.Ⅵ FAQ1. What is a 1N4007 diode used for?It is a general-purpose rectifier diode used to convert AC to DC, prevent reverse polarity, and protect circuits from voltage spikes (flyback protection).2. What is the difference between 1N4001 and 1N4007?The only difference is the Peak Repetitive Reverse Voltage. The 1N4001 is rated for 50V, while the 1N4007 is rated for 1000V. 1N4007 can replace a 1N4001, but a 1N4001 cannot replace a 1N4007 in high-voltage circuits.3. Can I replace 1N4148 with 1N4007?Generally, No. The 1N4148 is a high-speed signal diode (very fast switching, low current). The 1N4007 is a power rectifier (slow switching, high current). • If you put a 1N4007 in a high-speed data circuit, it will be too slow and fail to work.• If you put a 1N4148 in a power circuit, it will likely burn out due to its lower current limit (200mA vs 1A).4. How much current can a 1N4007 diode handle?It can handle 1 Ampere of continuous rectified current. It can handle a non-repetitive surge of 30 Amperes (for less than 8.3ms), which is useful for inrush current at startup.5. What is the voltage drop of 1N4007?While often cited as 0.6V or 0.7V, under a full 1A load, the voltage drop is typically 0.9V to 1.1V.6. What is M7 diode?M7 is the surface-mount (SMD) code for the 1N4007 diode in an SMA package. It has the same electrical specs: 1A, 1000V. body { font-family: Arial, sans-serif; line-height: 1.6; color: #333; } h2 { color: #2c3e50; border-bottom: 2px solid #3598db; padding-bottom: 10px; margin-top: 30px; } h3 { color: #34495e; margin-top: 20px; } table { width: 100%; border-collapse: collapse; margin: 20px 0; } table, th, td { border: 1px solid #ddd; } th, td { padding: 12px; text-align: left; } th { background-color: #f2f2f2; } img { max-width: 100%; height: auto; display: block; margin: 20px auto; } .note { background-color: #f9f9f9; border-left: 6px solid #2196F3; padding: 10px; font-style: italic; } .warning { background-color: #fff3cd; border-left: 6px solid #ffc107; padding: 10px; }
Kynix On 2021-11-11
IntroductionRelays are fundamental components in modern electronics, serving as switches that open and close circuits both electronically and mechanically. They regulate the flow of electricity by controlling circuit contacts. Even in 2025, with the rise of solid-state technology, electromechanical relays remain vital for high-current applications.Understanding the state of a relay is crucial:Normally Open (NO): The circuit is disconnected when the relay is inactive (not energized).Normally Closed (NC): The circuit is connected when the relay is inactive.When energy (electricity or an electrical charge) is supplied to the coil, these states change, allowing for precise control over high-power systems using low-power signals.Ⅰ What is a Relay and How Does it Work?A relay is an electrically operated switch. Traditional relays employ an electromagnet (coil) to mechanically operate a switching mechanism (contacts). When the coil is activated, it generates a magnetic field that moves the armature, changing the state of the contacts from open to closed (or vice versa).The relay diagrams below demonstrate the operational logic of standard relays.1.1 Sample Wiring Diagrams for a Normally Open RelayExample 1: A four-pin (normally open) relay with the switch placed on the positive side of the control circuit.Figure 1: Positive side switching configuration.Example 2: A four-pin (normally open) relay with the switch placed on the negative side of the control circuit.Figure 2: Negative side switching configuration.Ⅱ Relay Related Video Introduction Topic: Relay Terminal Numbering System, IEC Schematic Symbols, and Coil Voltage Explained.Video Description: In this tutorial, we explore how the Terminal Numbering system works (identifying relay pins), the IEC schematic symbol for 8-pin Ice Cube relays and Mini contactor relays, and critical information regarding Coil voltage. Specifically, we address why you cannot use DC voltage on a coil designed strictly for AC voltage.Ⅲ Why use a Relay?Relays allow a low-current circuit (like a microcontroller or dashboard switch) to control a high-current circuit (like a motor or headlight array). As of 2025, this isolation is critical for protecting sensitive digital electronics. Key advantages include:Safety & Protection: High-amperage power is kept away from the operator interface and sensitive control units.Cost & Space Efficiency: Thinner gauge wires connect the control switch to the relay, saving weight, space, and copper costs.Voltage Drop Reduction: Relays allow power to be routed directly from the source to the device over the shortest distance, minimizing voltage loss.Heavy Duty Compatibility: Heavy gauge cable is only required for the short run from the power source to the device (via the relay).3.1 Why does a Car Need a Relay?Automotive applications rely heavily on relays. Using a relay eliminates the need for high-current rated switches on the dashboard, which are bulky and expensive. Secondly, relays allow for decentralized power distribution; they can be placed closer to the load (e.g., headlights, electric motors, cooling fans) to ensure maximum efficiency. In modern Electric Vehicles (EVs), high-voltage relays are essential for battery management and safety disconnects.3.2 Why are Protection Devices used in a Relay?When an electromagnetic relay turns off, the magnetic field in the coil collapses rapidly, generating a significant voltage spike (Back EMF). This spike can damage sensitive components in the control circuit (like the ECU or transistors). To prevent this, Flyback Diodes or resistors are often installed across the relay coil. While resistors are more durable, diodes are generally more effective at clamping the voltage spike. The choice depends on the sensitivity of the driving circuit.Ⅳ How to Understand the Electrical Specifications of a Relay?Reading a relay's datasheet is vital for system longevity. Specifications are generally divided into two parts:Coil Ratings: Specifies the voltage (e.g., 12VDC, 24VDC, 120VAC) required to energize the electromagnet.Contact Ratings: Specifies the maximum voltage and amperage the internal switch can handle. Never exceed this rating.For Double Throw relays, you may see specifications formatted as "2 x switch"—one rating for the Normally Open (N/O) terminal and another for the Normally Closed (N/C) terminal (e.g., N/O: 35A at 14VDC, N/C: 20A at 14VDC).Ⅴ What’s the difference between 4 or 5 Pin Relays?The primary difference lies in the switching capability. A 4-pin relay typically controls a single circuit (on/off), whereas a 5-pin relay can switch power between two different circuits.4 Pin Relay (SPST - Single Pole Single Throw)4-pin relays typically feature two control pins (85 and 86) for the coil, and two power pins (30 and 87). They act as a simple on/off switch. When the coil is energized, the internal switch connects pin 30 to pin 87, powering the device.Figure 3: 4-Pin Relay (Open State)Figure 4: 4-Pin Relay (Closed/Energized State)5 Pin Relay (SPDT - Single Pole Double Throw)5-pin relays include two control pins (85 and 86), a common power pin (30), a Normally Open pin (87), and a Normally Closed pin (87A). This allows the relay to toggle power between two circuits. When at rest, power flows to 87A; when energized, power switches to 87.Figure 5: 5-Pin Relay SchematicNote: These diagrams are simplified to demonstrate functionality. If the relay coil is protected by a diode (internal or external), the coil terminal wired to the diode's anode must be connected to the negative ground to ensure proper polarity and protection.Ⅵ All Types of Relay SymbolsRelays vary by function, construction, and terminal configuration. Below is a list of common relay types and their schematic symbols.Electromagnetic RelayThe standard relay using a coil and magnetic field to move contacts mechanically.Figure 6: Electromagnetic Relay SymbolThermal Overload RelayThis relay uses a bimetallic strip instead of a magnetic coil. The strip bends as it heats up from current flow, opening auxiliary contacts to protect motors from overheating.Figure 7: Thermal Overload Relay SymbolSPST RelaySingle Pole Single Throw: Has four terminals total. It connects one input to one output.Figure 8: SPST Relay SymbolSPDT RelaySingle Pole Double Throw: Has five terminals. It features one common terminal that switches between a Normally Open (NO) and a Normally Closed (NC) terminal.Figure 9: SPDT Relay SymbolDouble Coil Latching RelayLatching relays maintain their contact position after the power is removed. A double coil version uses one coil to set the position and another to reset it.Figure 10: Latching Relay SymbolOvercurrent RelayDesigned to operate only when the current exceeds a specific threshold, protecting circuits from faults.Figure 11: Overcurrent Relay SymbolDifferential RelayActivates when there is a difference between two identical electrical quantities (e.g., input current vs. output current), commonly used in transformer protection.Figure 12: Differential Relay SymbolPulse RelayOperates based on pulse signals, toggling the contact state with each input pulse. Essential for lighting control systems.Figure 13: Pulse Relay SymbolOn/Off Time Delay RelayContains a timing mechanism that delays the closing or opening of contacts after the coil is energized or de-energized.Figure 14: Time Delay Relay SymbolRemanence RelayA specific type of latching relay that uses the magnetic remanence (residual magnetism) of the core to hold the position without continuous power.Figure 15: Remanence Relay SymbolNo Volt RelayAlso known as an Under-voltage Relay. It trips the circuit breaker when the voltage drops below a safe operational level.Figure 16: No Volt Relay SymbolAC and DC RelayWhile they perform similar switching functions, AC and DC relay coils are constructed differently regarding internal resistance and impedance.Figure 17: AC and DC Relay SymbolsPolarized RelayContains a permanent magnet in addition to the coil. The state of the contacts depends on the polarity of the input signal.Figure 18: Polarized Relay SymbolDistance Relay (Impedance Relay)Used primarily in high-voltage transmission lines. It detects faults by measuring the impedance on the line, which corresponds to the physical distance to the fault location.Figure 19: Distance or Impedance Relay SymbolⅦ FAQ1. What is the main purpose of a relay in a circuit?A relay acts as an electrically operated switch. It allows a low-power signal (like from a microcontroller) to control a high-power circuit (like a heater or motor), while keeping the two circuits electrically isolated.2. What is the circuit symbol for an amplifier vs. an aerial?While not relays, these are common components in related schematics:Amplifier: Represented by a triangle on its side. It increases signal strength.Aerial (Antenna): Often abbreviated as 'AE', it is the device used to transmit or receive signals.3. How is a relay connected to a transistor circuit?In a standard driver circuit, the relay coil is often connected to the Collector of a transistor. However, in an Emitter Follower configuration, the coil can be connected to the Emitter, where the input signal drives the Base and the output is taken from the Emitter load.4. How does a 12V automotive relay work?The relay is installed between the battery (power source) and the accessory (load). When the dashboard switch is flipped, it sends a small current to the relay coil. The coil energizes, closing the internal high-current contacts, allowing power to flow directly from the battery to the accessory.5. Why are symbols used in circuit diagrams?Schematic symbols provide a standardized, universal language for engineers. They show how components are electrically connected (logic), rather than their physical layout. This allows for easier troubleshooting and design verification.
Kynix On 2021-11-09
Ⅰ Introduction A capacitor is an electrical device that stores energy as an electric field. It consists of two metal plates separated by a dielectric or non-conducting material. Fixed capacitance and variable capacitance are the two broad categories of capacitors. The most common are fixed capacitance capacitors, but variable capacitance capacitors are also available. Rotary or trimmer capacitors are examples of these. Fixed capacitance capacitors are classified as film capacitors, ceramic capacitors, electrolytic capacitors, and superconductor capacitors. Follow the link to learn more about the various types of capacitors. This article goes into greater detail about the ceramic capacitor. Images of Capacitors Catalog Ⅰ Introduction Ⅱ Ceramic Capacitor Basics 2.1 What is a Ceramic Capacitor? 2.2 Ceramic Capacitor Polarity and Symbol 2.3 Types and Properties of Ceramic Capacitors 2.4 Ceramic Capacitor Classes Ⅲ Why Ceramic Capacitors Mostly Used in Electronic Circuit than Others? 3.1 Applications and Uses of Ceramic Capacitor 3.2 Properties or Advantages of Ceramic Capacitors Ⅳ How to Read Ceramic Capacitor? 4.1 Where to Use a Ceramic Capacitor? 4.2 How We Read Ceramic Capacitor Value? 4.3 Calculate Ceramic Capacitor Value 4.4 Some Examples Ⅴ FAQ Ⅱ Ceramic Capacitor Basics 2.1 What is a Ceramic Capacitor? The capacitor value is unchangeable. The working ceramic material acts as the dielectric, and it is a ceramic capacitor constructed of two or more alternating layers of ceramic and it has a metal layer acting as the electrodes, and the composition of the ceramic material defines the electrical behavior and thus applications. As per below video of ceramic capacitors: What is CERAMIC Capacitor _ Uses _ complete information in English 2.2 Ceramic Capacitor Polarity and Symbol Ceramic capacitors are the most common type of capacitor found in all electrical devices, and they use a ceramic material as the dielectric. Ceramic capacitors are non-polarity devices, which means they have no polarities. As a result, we can connect it to a circuit board in any direction. As a result, they are far safer than electrolytic capacitors. The symbol for a non-polarised capacitor is shown below. Many capacitors, such as tantalum beads, do not have polarity. Ceramic Capacitor Polarity and Symbol 2.3 Types and Properties of Ceramic Capacitors Ceramic capacitors come in three varieties, though other styles are available: Resin-coated leaded disc ceramic capacitors for through-hole mounting.Multi-Layer Ceramic Capacitors with Surface Mount (MLCC).Microwave bare lead-free disc ceramic capacitors that are designed to fit into a PCB slot. different types of ceramic capacitors Ceramic disc capacitors Ceramic disc capacitors are made by coating a ceramic disc on both sides with silver contacts. These devices can be made from multiple layers to achieve higher capacitances. Ceramic disc capacitors are typically through-hole components that are dwindling in popularity due to their size. If capacitance values allow, MLCCs are used instead. Ceramic disc capacitors have capacitance values ranging from 10pF to 100F and voltage ratings ranging from 16 volts to 15 kV and higher. Multi-layer ceramic capacitor (MLCC) MLCCs are fabricated by precisely combining finely ground granules of paraelectric and ferroelectric materials and then layering the mixture with metal contacts. Following the completion of the layering, the device is heated to a high temperature and the mixture is sintered, resulting in a ceramic material with the desired properties. The resulting capacitor is essentially made up of many smaller capacitors connected in parallel to increase the capacitance. MLCCs have 500 layers or more, with a minimum layer thickness of about 0.5 microns. As technology advances, layer thickness decreases, and higher capacitances for the same volume are achieved. 2.4 Ceramic Capacitor Classes Different ceramic capacitor classes are defined based on the working temperature range, temperature drift, and tolerance: Class 1 Ceramic Capacitors These are the most temperature-stable capacitors. They have nearly linear properties.The most commonly used dielectric compounds are.Magnesium Titanate is used to achieve a positive temperature coefficient.Calcium Titanate is used in capacitors that have a negative temperature coefficient. Class 2 Ceramic Capacitors Class 2 capacitors perform better at the price of volumetric efficiency, but at the expense of lower accuracy and stability. As a result, they are typically used for decoupling, coupling, and bypass applications where precision is not critical.Temperature range: -50 to +85 degrees CelsiusThe dissipation factor is 2.5 percent.Accuracy ranges from average to poor. Class 3 Ceramic Capacitors Class 3 ceramic capacitors have a high volumetric efficiency but a low dissipation factor. It is unable to withstand high voltages. Barium Titanate is a common dielectric.Temperature range of +10C to +55C will cause a -22% to +50% change in capacitance for a Class 3 capacitor.Dissipation factor: 3 to 5%.It will have a low level of accuracy (typically 20% or -20/+80%). Class 3 is typically used for decoupling or in other power supply applications where accuracy is not critical. Ⅲ Why Ceramic Capacitors Mostly Used in Electronic Circuit than Others? Many circuits, particularly electronic circuits, use ceramic capacitors, as you may have noticed. Ceramic capacitors are largely used over electrolytic or other capacitors. Ceramic capacitors 3.1 Applications and Uses of Ceramic Capacitor In electronic sensor circuits, ceramic capacitors are used.Ceramic capacitors are used in the transmission and reception of electronic signals.Ceramic capacitors are applied in circuits such as audio mixers, controllers, and equalizers.Ceramic capacitors are suitable for frequency-dependent circuits, such as electronic filter circuits, audio circuits, radio signal transmitters, and receiver circuits. Resonant circuits, like radio frequency communication system, needs ceramic capacitors, too.Ceramic capacitors are used in alternating current circuits for no polarity such as high voltage protection circuits, power circuit breakers, and so on.Ceramic capacitors are used in direct current motors to reduce radio frequency noise.Ceramic capacitors can also be used as Bypass Capacitors.Why Ceramic Capacitors mostly used in Electronic Circuit? 3.2 Properties or Advantages of Ceramic Capacitors Ceramic capacitors are available in extremely small sizes, which is a significant benefit. Because of the numerous electronic circuits, in fact, most modern electronic circuits necessitate the use of small size capacitors. Many critical electronic circuits necessitate the use of very small capacitors. Ceramic capacitors are available in a wide range of sizes. Ceramic capacitors can provide very high stability; in fact, they offer a wide range of stability. Ceramic capacitors have a low temperature coefficient and a higher voltage breakdown characteristic. 5. Ceramic capacitors are the best choice for high-frequency applications. Ⅳ How to Read Ceramic Capacitor? Two reference tables MarkingCapacitance (pF)Capacitance (ìF)101100 pF0.0001 ìF221220 pF0.00022 ìF471470 pF0.00047 ìF1021,000 pF0.001 ìF2222,200 pF0.0022 ìF4724,700 pF0.0047 ìF10310,000 pF0.01 ìF22322,000 pF0.022 ìF47347,000 pF0.047 ìF104100,000 pF0.1 ìF224220,000 pF0.22 ìF474470,000 pF0.47 ìF1051,000,000 pF1 ìF2252,200,000 pF2.2 ìF4754,700,000 pF4.7 ìF Letter printed capacitor indicate tolerance LetterToleranceA±0.05 pFB±0.1 pFC±0.25 pFD±0.5 pFE±0.5%F±1%G±2%H±3%J±5 %K±10%L±15%M±20%N±30%P–0%, + 100%S–20%, + 50%W–0%, + 200%X–20%, + 40%Z–20%, + 80% 4.1 Where to Use a Ceramic Capacitor? Ceramic capacitors are applied in a variety of applications. It is primarily used for filtration. It is used in a signal or frequency circuit to filter and purify the signal. It can convert a direct current to a direct current. The ceramic capacitor is a genre of energy storage device. It stores the DC while passing the AC. This is what the ceramic capacitor looks like. 4.2 How We Read Ceramic Capacitor Value? alphabetic code The first is an alphabetic code that indicates the component's tolerance. The second is a numeric code that tells us the actual capacitance of the capacitor. So let's take a look at our example right now. In our example, the value is 102 k. The first significant digit in the code is one, and the second significant digit is zero. As a result, these are the numbers in front of our multiplier. How to read the values of Ceramic Capacitors? 4.3 Calculate Ceramic Capacitor Value So, if we take your multiplier, which is two, and looks at the chart, that equals two zeros. As a result, we append two zeros to the end of the number. So, picofarad, it's 1000. Now, K represents our component tolerance, which in this case is plus or minus 10%. So that's how we figure out the capacitor's size and rating. Now I'm going to show you how to use a multimeter to measure the capacitance of a capacitor. In this example, I'm using a capacitor with the numerical value 103 written on it, which equals 10-nanofarads. nine ferrites When you look at the display of what is rated, you'll notice that its practical rating is it works, and it has nine ferrites. So tolerances are around 10%. When you connect it to your actual multimeter, In this one, make sure you have an appropriate terminal. As you can see, I have the capacitance symbol in the bottom right-hand corner. Then, make sure your multimeter is set to the appropriate range. Then double-check that you've selected the correct option. Ceramic disk capacitor codes table Picofarad pFNanofarad nFMicrofarad FCode100.010.00001100150.0150.000015150220.0220.000022220330.0330.000033330470.0470.0000474701000.10.00011011200.120.000121211300.130.000131311500.150.000151511800.180.000181812200.220.000222213300.330.000333314700.470.000474715600.560.000565616800.680.000686817500.750.000757518200.820.00082821100010.00110215001.50.0015152200020.00220222002.20.002222233003.30.003333247004.70.0047472500050.00550256005.60.005656210000100.110215000150.01515222000220.02222333000330.03333347000470.04747368000680.0686831000001000.11041500001500.151542000002000.22542200002200.222243300003300.333344700004700.474746800006800.68684100000010001105150000015001.5154200000020002205220000022002.2225330000033003.3335470000047004.7475 The final number written on a ceramic capacitor is the power of ten multiplied by the first two numbers. If a ceramic capacitor has the code 682, First, look at the last number. So, as we can see, the final number is 2. The multiplier is now 102. 4.4 Some Examples 204 = 20×104 = 200000 PF 472 = 47×102 = 4700 PF 502 = 50×102 = 5000 PF 330 = 33×100 = 33 PF [100 = 1] UNITS 1000 nanofarad(nF) = 1 microfarad(µF) 1 picofarad = 10-12farads. Nano= 10-9 Micro= 10-6 1 Nano Farad= 10-9 Farad 1 Microfarad (µF)= 10-6 Farad 1 nF = 1000 pF 1 pF = 0.001 nF Example: convert 15 nF to pF: 15 nF = 15 × 1000 pF = 15000 pF Capacitor voltage code 0G4VDC0L5.5VDC0J6.3VDC1A10VDC1C16VDC1E25VDC1H50VDC1J63VDC1K80VDC2A100VDC2Q110VDC2B125VDC2C160VDC2Z180VDC2D200VDC2P220VDC2E250VDC2F315VDC2V350VDC2G400VDC2W450VDC2H500VDC2J630VDC3A1000VDC Ⅴ FAQ 1. What is ceramic capacitor used for? Ceramic capacitors are used for all types of circuits in a number of applications. There are four main capacitor applications that are described in detail below: coupling, decoupling, smoothing, and filtering. 2. Do ceramic capacitors go bad? Like mica capacitors, ceramic capacitors also very rarely go bad. Do not replace ceramic disc capacitors unless you are sure one has gone bad. ... While replacing the capacitors, check the radio's resistors. Since you will be replacing the capacitors, you should snip one lead of each paper and electrolytic capacitor. 3. Why do ceramic capacitors fail? Ceramic capacitors can fail in a couple of ways. They can be mechanically damaged - too much physical stress (pressure on the part or the board is bent a little too much) can cause a crack. The capacitor will then develop short circuits between layers. It acts more like a resistor in that case. 4. When should you use a capacitor? Capacitors are widely used in electronic circuits for blocking direct current while allowing alternating current to pass. In analog filter networks, they smooth the output of power supplies. 5. What is the practical use of capacitor? The most common use for capacitors is energy storage. Additional uses include power conditioning, signal coupling or decoupling, electronic noise filtering, and remote sensing. Because of its varied applications, capacitors are used in a wide range of industries and have become a vital part of everyday life. 6. Why capacitor is not used as battery? Capacitors don't provide large amount of energy because they have less energy density than batteries. Capacitors are useful to provide short duration power requirements because they can be charged or discharged at a higher rate than the batteries.
kynix On 2021-11-02
Introduction The rectifier diode is a semiconductor device that converts AC into DC. Usually it contains a PN junction with two terminals, a positive electrode and a negative electrode. The most important characteristic is unidirectional conductivity. In electronic circuits, its breakdown voltage is high, the reverse leakage current is small, and the high temperature performance is good. Generally, it can be made of materials such as semiconductor germanium or silicon. In addition, high-voltage and high-power rectifier diodes are made of high-purity single crystal silicon (it is easy to reverse breakdown when there is more doping). This kind of device has a large junction area and can pass a large current (up to thousands of amperes), but the operating frequency is not high, generally below tens of KHz. Rectifier diodes are mainly used in various low-frequency half-wave rectifier circuits. If require full-wave rectification, several diodes need to be connected to form a rectifier bridge. What is a Rectifier? (AC to DC) Catalog Introduction Ⅰ Common Parameters Ⅱ Rectifier Diodes Selection Ⅲ Rectifier Common Failures Ⅳ Rectifier Diodes Detection Ⅴ Rectifier Diode Replacement 5.1 Replacing Rules 5.2 Commonly Used Rectifier Models List Ⅵ Rectifier Diode Circuit Types 6.1 Half-Wave Rectifier Circuit 6.2 Full-Wave Rectifier Circuit 6.3 Bridge Rectifier Circuit Ⅶ High-frequency Rectifier Diodes Ⅷ FAQ Ⅰ Common Parameters The rectifier diode uses the unidirectional conductivity of the PN junction to convert alternating current into pulsating direct current. Rectifier diodes have a large leakage current, and most of them are diodes packaged with surface mount materials. The parameters of the rectifier diode include the maximum rectifier current, which refers to the maximum current value allowed by the rectifier diode for long-term operation. It is the main parameter of the rectifier diode and the main basis for the option of the rectifier diode. Except it, other important parameters are introduced here.(1) Maximum average rectified current IF: It refers to the maximum forward average current allowed to pass through the diode during long-term operation. The current is determined by the PN junction area and the heat dissipation conditions. It should be noted that the average current passing through the diode cannot be greater than this value, and has heat dissipation.(2) Maximum reverse working voltage VR: It refers to the maximum reverse voltage allowed to be applied across the diode. If it is greater than this value, the reverse current (IR) will increase sharply, and the unidirectional conductivity of the diode will be destroyed, causing reverse breakdown. Usually take half of the reverse breakdown voltage VB as VR.(3) Maximum reverse current IR: It is the reverse current allowed to flow through the diode under the highest reverse working voltage. This parameter reflects the quality of the unidirectional conductivity of the diode. Therefore, the smaller the current value, the better the diode quality.(4) Breakdown voltage VB: It refers to the voltage value at the sharp bend point of the reverse volt-ampere characteristic curve of the diode. When the reverse is a soft characteristic, it refers to the voltage value under a given reverse leakage current condition.(5) The highest operating frequency fm: It is the highest operating frequency of the diode under normal conditions. It is mainly determined by the junction capacitance and diffusion capacitance of the PN junction. If the operating frequency exceeds fm, the unidirectional conductivity of the diode will not be well reflected.(6) Reverse recovery time trr: It refers to the reverse recovery time under the specified load, forward current and maximum reverse transient voltage.(7) Zero-bias capacitor CO: It refers to the sum of the capacitance of the diffusion capacitance and the junction capacitance when the voltage across the diode is zero. It is worth noting that, due to the limitation of the manufacturing process, even the same type of diode has a large dispersion of its parameters. The parameters given in the manual are often within a range. If the test conditions change, the corresponding parameters will also change. For example, the IR of the 1N5200 series silicon plastic rectifier diode measured at 25°C is less than 10uA, and at 100°C IR becomes less than 500uA. Ⅱ Rectifier Diodes Selection Rectifier diodes are generally planar silicon diodes, which are used in various power rectifier circuits. When selecting a rectifier diode, the parameters such as its maximum rectifier current, maximum reverse working current, cut-off frequency and reverse recovery time should be mainly considered.The rectifier diode used in the ordinary series stabilized power supply circuit does not require high reverse recovery time of the cut-off frequency. The rectifier diode with the maximum rectified current and maximum reverse working current should meet the requirements of the circuit.The rectifier diode used in the rectifier circuit of the switching regulated power supply and the pulse rectifier circuit should be a rectifier diode with a higher operating frequency and shorter reverse recovery time (such as RU series, EU series, V series, 1SR series, etc.) or select fast recovery diodes, or Schottky rectifier diode. Ⅲ Rectifier Common Failures (1) Inadequate lightning protection and poor overvoltage protection. The rectifier device is not equipped with lightning protection and overvoltage protection devices. Or insufficient routine maintenance of the equipment.(2) Poor operating conditions. In the indirect drive generator set, because the calculation of the speed ratio is incorrect or the ratio of the diameters of the two belt pulleys does not meet the requirements of the speed ratio, the generator runs at a high speed for a long time, so the rectifier is at a higher voltage for a long time. It accelerates the rectifier aging, and was damaged by premature breakdown.(3) Poor operation management. The load failure or diode breakdown doesn’t fixed in time.(4) Poor equipment installation or manufacturing process. The generator set has been operating under large vibration for a long time, which affects the rectifier tube operation. At the same time, because the generator set speed is unstable, the working voltage of the rectifier tube also fluctuates, which greatly accelerate the aging and damage of the rectifier tube.(5) The specifications and models of the rectifier tube do not match. When replacing a new rectifier tube, wrongly replace the tube whose working parameters do not meet the requirements or the wiring is wrong, causing the rectifier tube to breakdown and damage.(6) The safety margin of the rectifier tube is too small. The overvoltage and overcurrent safety margin of the rectifier tube is too small, so that the rectifier tube cannot withstand the overvoltage or the peak value of the overcurrent transient process that occurs in the generator excitation circuit and is damaged. Figure 1. Diode as Rectifier Symbol Ⅳ Rectifier Diodes Detection Here is a more general and simple method. Remove all the rectifier diodes in circuit, use the 100×R or 1000×R ohm range of a multimeter to measure the two lead wires of the rectifier diode (adjust and test twice). If the resistance values measured twice are very different, for example, the resistance value is as high as a few hundred kΩ to infinity, or the resistance value is only a few hundred Ω or less, indicating that the diode is good (except under special circumstances). If the resistance value measured twice is almost the same and the resistance value is very small, it means that the diode has been broken down and cannot be used. In addition, if the resistance values measured twice are both infinite, it means that the diode has been internally disconnected and cannot be used. Ⅴ Rectifier Diode Replacement 5.1 Replacing Rules After the rectifier diode is damaged, you should replace with the same model or another model with the same parameters.Generally, rectifier diodes with high withstand voltage (reverse voltage) can be substituted for rectifier diodes with low withstand voltage, while rectifier diodes with low withstand voltage cannot be replaced with rectifier diodes with high withstand voltage. A diode with a high rectification current value can be substituted for a diode with a low rectification current value, while a diode with a low rectification current value cannot be substituted for a diode with a high rectification current value. 5.2 Commonly Used Rectifier Models List Material Model Reverse Voltage Operation (peak) Average Rectified Current Silicon Rectifier Diode 1N4001 50V 1A (Ir=5uA,Vf=1V,Ifs=50A) 1N4002 100V 1A 1N4003 200V 1A 1N4004 400V 1A 1N4005 600V 1A 1N4006 800V 1A 1N4007 1000V 1A 1N4148 75V 4PF, Ir=25nA,Vf=1V 1N5391 50V 1.5A (Ir=10uA,Vf=1.4V,Ifs=50A) 1N5392 100V 1.5A 1N5393 200V 1.5A 1N5394 300V 1.5A 1N5395 400V 1.5A 1N5396 500V 1.5A 1N5397 600V 1.5A 1N5398 800V 1.5A 1N5399 1000V 1.5A 1N5400 50V 3A (Ir=5uA,Vf=1V,Ifs=150A) 1N5401 100V 3A 1N5402 200V 3A 1N5403 300V 3A 1N5404 400V 3A 1N5405 500V 3A 1N5406 600V 3A 1N5407 800V 1A (Ir=5uA,Vf=1V,Ifs=50A) 1N5408 1000V 1A Ⅵ Rectifier Diode Circuit Types The power grid supplies users with alternating current, and various electrical devices require direct current. Rectification is the process of converting AC into DC. Utilizing the device with unidirectional conductivity, the current of alternating direction and magnitude can be converted into direct current. The following introduces three main rectifier circuits composed of crystal diodes. 6.1 Half-Wave Rectifier Circuit Figure 2. Half-Wave Rectifier Circuit The figure shows the simplest rectifier circuit. It is composed of power transformer B, rectifier diode D and load resistor Rfz. The transformer transforms the voltage into the required alternating voltage e2, and then D transforms the AC into pulsating DC.The transformer threshold voltage e2 is a sine wave voltage whose direction and magnitude change with time, and its waveform is shown in Figure (a). In the 0~K time, e2 is a positive half cycle, that is, the upper end of the transformer is positive and the lower end is negative. At this time, the diode is in forward conductive conduction, and e2 is added to the load resistor Rfz through it. Within π~2π, e2 is in negative half cycle, the lower end of the transformer secondary is positive, and the upper end is negative. At this time, D bears the reverse voltage and does not conduct, and there is no voltage on Rfz. In the time of π~2π, the process of 0~π time is repeated, and in the time of 3π~4π, the process of π~2π time... half-cycle through Rfz, a single right direction voltage is obtained on Rfz (up positive and lower negative), as shown in Figure (b), which achieves the purpose of rectification. But the load voltage Usc, and the load current also changes with time, so it is usually called pulsating DC. Figure 3. Half-Wave Rectifier Wave This rectification method of removing the first half week and leaving half a week is called half wave rectification. It is not difficult to note that the half-wave rectification is at the expense of consuming half of the AC in circuit, and the current utilization rate is very low. According to it, half-wave rectifier diode is commonly used in high voltage and small current occasions, and is rarely used in general radio devices. 6.2 Full-Wave Rectifier Circuit Figure 4. Full-Wave Rectifier Circuit If some adjustments are made to the structure of the rectifier circuit, a full-wave rectifier circuit that can be obtained. The figure above is the electrical schematic diagram of the full-wave rectifier circuit.The full-wave rectifier circuit can be regarded as a combination of two half-wave rectifier circuits. A tap needs to be drawn in the middle of the secondary coil of the transformer to divide the secondary coil into two symmetrical windings, so as to get two voltages e2a and e2b of equal size but opposite polarity to form two energized circuits.The working principle of the full-wave rectifier circuit can be illustrated by the waveform diagram. Between 0 and π, e2a is a positive voltage to Dl, D1 is turned on, and a up positive and down negative voltage is obtained on Rfz. e2b is a reverse voltage to D2, and D2 is not conductive (see Figure(b) ). In the time of π-2π, e2b is a positive voltage to D2, D2 is turned on, and the voltage obtained on Rfz is still up positive and down negative voltage, therefore e2a is a reverse voltage to D1, and D1 is not conductive (see figure (c). Figure 5. Full-Wave Rectifier Circuit Wave Repeated this way, because the two rectifier elements D1 and D2 conduct electricity in turn, the result is that the load resistor Rfz has the same direction of current at the positive and negative half cycles, as shown in Figure(b). This is full-wave rectification, which not only uses the positive half-cycle, but also cleverly uses the negative half-cycle. Full-wave rectifier greatly improves the rectification efficiency. Figure 6. Full-Wave Rectifier Circuits This circuit requires the transformer to have a secondary center tap that makes the two ends symmetrical, which brings a lot of trouble to the production. In addition, in this circuit, the maximum reverse voltage that each rectifier diode can withstand is twice the maximum value of the transformer secondary voltage, so diodes should withstand higher voltages. 6.3 Bridge Rectifier Circuit Figure 7. Bridge Rectifier Circuit The bridge rectifier circuit is the most used rectification circuit. It has the advantages of a full-wave rectifier circuit as long as two diode ports are connected to form a bridge structure, so its shortcomings are overcome to a certain extent.The bridge rectifier circuit is as follows: Figure 8. Bridge Rectifier Circuit (a) When e2 is a positive half cycle, D1, D3 and the direction voltage, D1, D3 are turned on; D2, D4 are applied with reverse voltage, they are turned off. E2, Dl, Rfz, and D3 are energized a loop in the circuit. On Rfz, a positive and negative half-wave washing voltage is formed. When e2 is a negative half cycle, a positive voltage is applied to D2 and D4, and they are turned on; Apply reverse voltage to D1 and D3, they are cut off. E2, D2Rfz, and D4 are energized a loop in the circuit, and the other half-wave rectified voltage is also formed on Rfz. Figure 9. Bridge Rectifier Circuit (b) If repeated, a full-wave rectified voltage at Rfz is made. The waveform diagram is the same as the full-wave rectifier. It is not difficult to see from the figure that the reverse voltage of each diode in the bridge circuit is equal to the maximum value of the secondary voltage of the transformer, which is half smaller than the full-wave cleaning circuit. Ⅶ High-frequency Rectifier Diodes The rectifier diode in the switching power supply must have the characteristics of low forward voltage reduction and fast recovery, and should also have sufficient output power. The following three types of high-frequency diodes can be used: fast recovery rectifier, ultra-fast recovery rectifier, and Schottky diode rectifier.Fast recovery and ultra-fast recovery rectifier diodes have moderate and high forward voltage drop, and the range is from 0.8 to 1.2V. These two types of rectifier diodes also have higher cut-off voltage parameters. Therefore, they are particularly suitable for use in low-power auxiliary power circuits with output voltages around 12V.Compared with general rectifier diodes, the reverse recovery time difference between fast recovery rectifier diodes and ultra-fast recovery rectifier diodes is reduced to the nanosecond level, thus greatly improving the efficiency of the power supply. According to experience, when choosing a fast recovery rectifier diode, its reverse recovery time should be at least 1/3 of the rise time of the switching transistor. These two kinds of rectifier diodes also reduce the switching voltage spike, because it will affect the ripple of the output DC voltage.Whether fast recovery rectifier diodes and ultra-fast recovery rectifier diodes used in switching power supplies need a heat sink, which depends on the maximum power of the circuit. Under normal circumstances, the allowable junction temperature is 175°C during manufacture. The manufacturer has a technical parameters provided for the designer to calculate the maximum output operating current, voltage, and case temperature. Even under the action of a large forward current, the forward voltage drop of Schottky rectifier diodes is very low, only about 0.4V. Moreover, as the junction temperature increases, its forward voltage drop decreases. Therefore, Schottky rectifier diodes are particularly suitable for low-voltage output circuits around 5V. Its reverse recovery time is negligible, because this device is a semiconductor device with majority carrier. During the switching process of the device, there is no need to remove the stored charge of the minority carrier.Schottky rectifier diodes have two major shortcomings: First, the reverse cut-off voltage tolerance is low, about 100V; second, the reverse leakage current is large, making the device more susceptible to have heat breakdown than other types of rectifier devices. Of course, these shortcomings can also be overcome by adding a transient overvoltage protection circuit and appropriately controlling the junction temperature. Ⅷ FAQ 1. How does a rectifier diode work?A rectifier is a device that converts an Alternating Current (AC) into a Direct Current (DC) by using one or more contact diodes. ... In simple words, a diode allows current in just one direction. This unique property of the diode allows it to act sort of a rectifier by converting an alternating current to a DC source. 2. What is a function of rectifier diode?A rectifier diode is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC). 3. What is the function of diode in rectifier circuit?A characteristic of diodes is that current flows (forward direction) or current does not flow (reverse direction) depending on the direction of applied voltage. This works to convert alternating current (AC) voltage to direct current (DC). 4. Which is used as rectifier?We know that the core use of rectifier is to convert AC current into DC current. The rectifier consists of semiconductor diodes to do this function. 5. What is the limitation of a diode rectifier?Disadvantages of Full Wave Bridge RectifierIt needs four diodes. The circuit is not suitable when a small voltage is required to be rectified. It is because, in this case, the two diodes are connected in series and offer double voltage drop due to their internal resistance. 6. What is the ideal rectifier diode efficiency?It is the ratio of DC output power to the AC input power. The rectifier efficiency of a full-wave rectifier is 81.2%. 7. What is a fast recovery rectifier?Definition: Fast Recovery Diode is a semiconductor device which possesses short reverse recovery time for rectification purpose at high frequency. A quick recovery time is crucial for rectification of high-frequency AC signal. Diodes are mostly used in rectifiers because they possess ultra-high switching speed. 8. Which diode is fast recovery diode?FRD stands for fast recovery diodes. They offer high-speed support and generally have a trr of approximately 50 to 100 ns. With a VF of approximately 1.5V, it is rather large when compared to general rectifying diodes. Another generic term for the FRD type would be a “High-speed Diode.” 9. What is ultra fast recovery diode?A fast diode is a faster-than-standard current rectifier. ... A fast rectifier typically recovers ten times faster than a standard rectifier, and an ultrafast designation is usually applied to rectifiers designed to beat the standard rectifier recovery by being more than fifty times faster. 10. What is the difference between a Schottky diode and a rectifier diode?Schottky diode, also known as barrier diode is mainly used in low voltage circuits because the forward voltage drop of Schottky diode(Vf) is less than a rectifier diode. The forward voltage drop of a Schottky diode is typically in the range of . 25 to 0.5 V whereas the Vf of a rectifier diode is around 0.7 volts. 11. What is Schottky barrier rectifier?The Schottky diode or Schottky Barrier Rectifier is named after the German physicist Walter H. Schottky, is a semiconductor diode designed with a metal by the semiconductor junction. It has a low-forward voltage drop and a very rapid switching act. ... Actually, it is one of the oldest semiconductor devices in reality.
kynix On 2021-10-22
Ⅰ Introduction One type of primary capacitor is the variable capacitor. Capacitors are classified into two types based on their capacitance. These are known as 'Fixed Capacitors' and 'Variable Capacitors.' Capacitors with a fixed capacitance value are referred to as 'Fixed Capacitors.' Similarly, capacitors with varying capacitance are referred to as Variable Capacitors. What is a variable capacitor diode – how does it work? | Intermediate Electronics This type of capacitor has the competence to change the capacitance values "Electrically" or "Mechanically." Variable Capacitors, unlike Fixed Capacitors, provide specific ranges of values rather than deciding the values during manufacturing. These capacitors are chosen based on the required values. This type of capacitor is preferred in the majority of Tuning Circuits. Catalog Ⅰ Introduction Ⅱ What is a Variable Capacitor? Ⅲ Construction of Variable Capacitor 3.1 Summery Ⅳ Types of Variable Capacitors 4.1 Tuning Capacitors 4.2 Common problems in turning circuits 4.3 Trimmer Capacitors 4.4 Mechanical Capacitors 4.5 Electronic Capacitors Ⅴ Working principle of Variable Capacitors 5.1 Turning types 5.2 Ceramic trimmers 5.3 Plastic foil types Ⅵ Variable Capacitor Applications Ⅶ FAQ Ⅱ What is a Variable Capacitor? Figure1:Variable Capacitor Symbol Ⅲ Construction of Variable Capacitor The variable capacitor's construction is shown below. As their simple construction, these capacitors are commonly used in a variety of applications. These capacitors are typically constructed with two sets of hemispherical metal plates separated by air gaps. One set of metal plates is fixed, while the other is connected to a shaft, allowing the user to turn the assembly and change the capacitance as needed. As a result, the construction of each type of capacitor differs. Figure2: construction-of-variable-capacitor The working principle of a basic capacitor can be applied to design this capacitor. The conductive plates of this capacitor are arranged in parallel and separated by dielectric coatings made of various materials such as reinforced paper, mica, or certain types of ceramics. These capacitors, unlike traditional fixed capacitors, are designed to change capacitance levels. In most cases, we can gain variable capacitance by varying the distance between parallel plates within a capacitor. 3.1 Summery This capacitor is built by inserting metal plates into it.Some of them are 'Fixed Plates,' while the rest are 'Movable Plates.'The area between the Fixed and the movable plates changes as a consequence of the rotation of the movable plates.Each type of capacitor in this category is built uniquely. Ⅳ Types of Variable Capacitors In the market, there are two types of variable capacitors, which are as follows. The capacitance of the following capacitors can be changed manually with screwdrivers; otherwise, any device can be used. Tuning CapacitorsTrimmer CapacitorsMechanical CapacitorsElectronic Capacitors 4.1 Tuning Capacitors Tuning capacitors can be designed with the help of a frame. This frame has both a stator and a rotor. The frame of the capacitor can support both the mica material and the stator. When the stator is turned off, the rotors begin to rotate with the assistance of a shaft. When the movable rotor plates enter the immobile stator, the capacitance value is maximum; otherwise, it is minimum. These capacitors can provide capacitance values ranging from picofarads to tens of picofarads. Figure3:Tuning Capacitors These capacitors are used in radio receivers with LC circuits. Tuning condensers is another name for these capacitors. 4.2 Common problems in turning circuits Variable capacitors used in tuning circuits can cause several issues. The main issue with the older types is a bend in the plates, which causes the component to short and thus become inoperative. As shown in Figure 1, this short can be detected. Figure 4 - Testing a variable capacitor with a multimeter. There must be no indication of low resistances around the entire turn of the variable capacitor. In good condition, the meter's needle should remain on infinite to a variable. If a short is discovered between the plates, the first step should be to attempt to correct the alignment of these plates using the screw that exists in the mobile variable axis. It is possible to adjust the plates if they are bent by pressing and releasing this screw. If the plates are bent, the technician can attempt to correct the defect very carefully, always performing a continuity test to detect the moment when the component is recovered. The insulating sheets inside them may have a small variable short problem. By carefully dismantling the component, you can obtain the defective sheets and attempt to correct the defect, or with insulating use of other variables abandoned by the same problem, or even with the improvisation of insulating sheets. Figure 5 depicts how the metal plates are arranged, with an insulating foil sandwiched between them to prevent contact between the mobile and fixed assemblies. Figure 5 - Construction of a variable with plastic insulation. After reassembly, an isolation test should be carried out to ensure that the short between the plates was indeed removed. If the problem is moisture or dirt, the variable can be disassembled for cleaning, but be careful not to bend plates and remember to reassemble any insulating sheet. 4.3 Trimmer Capacitors Trimmer capacitors are used to provide basic calibration of equipment during manufacturing or servicing. These capacitors are frequently arranged on the printed circuit board in such a way that the user does not have access to change them. As a result, these capacitors are inexpensive. These capacitors are used in circuits to set the oscillator frequency, rise, latencies, and fall times. These capacitors enable servicemen to adjust devices as needed. These capacitors are classified into two types: air trimmer and ceramic trimmer. There are three leads in this capacitor. The first lead is connected to the immobile part, the second to the rotary, and the third to the common. The purpose of a semi-circle-shaped movable disc is to observe the movement of this capacitor. This capacitor has two plates that are separated by a dielectric material and are arranged in parallel to each other. Figure6:Trimmer Capacitors These capacitors can be classified based on the dielectric material used, such as air trimmer or ceramic trimmer. 4.4 Mechanical Capacitors These capacitors are made up of a series of curved plates that are connected to a knob. The main advantage of this is that the capacitance of the capacitor can be easily changed if necessary. Mechanically, these are dependable because they are not overly complicated. 4.5 Electronic Capacitors By applying a DC voltage to these capacitors, you can change their capacitance. These capacitors' main applications are multimeters, resistance, and amperage. The DC (direct current) here refers to the type of current supplied by a battery. Ⅴ Working principle of Variable Capacitors The capacitance can be varied between a minimum and a maximum value using an electrode system composed of one fixed and one movable part – stator and rotor. The temperature coefficient (TC) for the various dielectrics has a great difference from the corresponding values for fixed capacitors. Except for the best precision components, the variations are significantly larger, which has to do with the mechanical conditions as well as the entire construction. Trimmer capacitors are primarily used on printed circuit boards (PCBs), but surface mount designs are becoming increasingly popular. Trimmers frequently have friction, which increases the turning moment and, as a result, locks the capacitor in its adjusted position. 5.1 Turning types Air dielectric As shown in Figure 7, the classic variable capacitor is be composed of semicircular electrodes that can be turned into each other. The styles are designed for either PCB or panel mounting. They are mainly used for tuning resonance circuits. Figure7: A variable air-insulated capacitor schematic and an example of Tronser's design. Mechanical precision is required due to the air-insulated electrodes. The plate distance is usually between 0.2 and 1 mm. The cost is fairly high. 5.2 Ceramic trimmers We can make a ceramic trimmer capacitor by reducing the plates in Figure 7 to just one silver-plated ceramic rotor that is turned in over the stator electrode. Figure C5-2 depicts an example of this design. There are also multilayer designs. The capacitors are available in both hole mount and surface mount configurations.Because Type 1 ceramics are used, losses will be minimal. Figure 8: Explanatory sketch of a cross-cut using a ceramic trimmer. 5.3 Plastic foil types If we replace the air insulation in Figure 7 with some plastic foil, the electrode distance can be reduced while the r – and thus the capacitance – increases, albeit at the expense of a slightly lower Q value. Low loss plastics such as Teflon (PTFE), polypropylene (PP), and polycarbonate (PC) are common, but polyester (PETP) is also available. Ⅵ Variable Capacitor Applications Ⅶ FAQ 1). What is the main function of the variable capacitor? It is used to fix the resonant frequency in the LC circuit. 2). How these capacitors are made? These are made with two sets of curved metal plates and they are divided by air gaps 3). What is a ganged capacitor? The combination of two capacitors that are connected together is known as a ganged capacitor. 4). What are the two types of variable capacitors? They are tuning capacitors and trimming capacitors. 5). What is the capacitance values of a variable capacitor? Typically ranges from 100pF to 500pF Thus, this is all about variable capacitors and the characteristics of the variable capacitor mainly include accuracy, tolerance, polarity, voltage rating, and capacitance range. Here is a question for you, what are the advantages of a variable capacitor?
kynix On 2021-10-20
Join our mailing list!
Be the first to know about new products, special offers, and more.
Feature Posts
How Resistors Work: From Basic Principles to Advanced Applications2025-07-30
DC Switching Regulators: Principles, Selection, and Applications2025-05-30
FPGA vs CPLD: In-depth Analysis of Architecture, Performance and Application2025-05-07
MOSFET Technology: Essential Guide to Working Principles & Applications2025-05-04
SMD Resistor: Types, Applications, and Selection Guide2025-04-30