The Kynix Blog

There is no doubt that the use of LCD headlamp is a succcessful further step towards digitalizing lighting. LCD headlamp which enables complex functions will also be relevant to autonomous driving. Let's talk something about the following research project about developing a headlamp basics on a LCD (  Full name is Liquid Crystal Display )which made by HELLA and seceral partners.This technology is an good example already known in the home entertainment field.  About The ProjectIn the context of the research project funded by the Federal Ministry of Education and Research (BMBF) regarding the fully adaptive light distribution for intelligent, efficient and safe vehicle lighting (VoLiFa2020), HELLA has developed a headlamp on the basis of a Liquid Crystal Display (LCD) in collaboration with project partners Merck, Institut für Großflächige Mikroelektronik IGM, Stuttgart University, Porsche, Elmos Semiconductor, Schweizer Electronic, and the University of Paderborn. Complex FunctionsIn general,the new LCD headlamp projects 30.000 pixels onto the road. This allows adjusting the light pattern in an intelligent and continuous manner to various driving situations in real time. The use of an LC display is a further step towards digitalizing lighting. This means: the adaptation of the light pattern will increasingly be determined by software. The driver will obtain the best possible view of the road. Individual segments with e.g. other traffic participants or strongly reflecting street signs can be omitted or dimmed in a targeted manner. Highly complex functions are also conceivable: navigation arrows or lines showing the ideal lane can be projected onto the road. LCD technology enables functions that will also be relevant to autonomous driving.  The LC display is the headlamp’s key component. It is situated between the LED light source and the projection lens. The display generates a matrix with 100 x 300 pixels that can be individually controlled and dimmed. A camera installed in the vehicle as well as a sensor optically reading distances and speeds (light detection and ranging sensor, LiDAR), will forward the ambient information to the headlamp control unit via a processor. This will then direct the individual display pixels up to 60 times per second. 25 high-power LED’s arranged in three rows will serve as light source. Each LED’s light intensity will be adjusted to the respective lighting situation. Due to increasing traffic volumes and safety requirements, intelligent lighting systems are of increasing importance. LCD technology enables completely new functionalities and opportunities here. And the use is not limited to passenger cars. Other vehicle categories, such as commercial vehicles or buses also provide meaningful application areas. ThanksgivingThanks to this project's great resolution and sharpness of detail, it opens up a diffirent new paths in automotive lighting technology. 

Have you heard of Silicon carbide power devices yet? Researchers are rolling out a new manufacturing process and chip design for silicon carbide (SiC) power devices, which can be used to more efficiently regulate power in technologies that use electronics. The process -- called PRESiCE -- was developed to make it easier for companies to enter the SiC marketplace and develop new products.(Silicon carbide power devices, like the one shown here, are more efficient than their silicon counterparts.)"PRESiCE will allow more companies to get into the SiC market, because they won't have to initially develop their own design and manufacturing process for power devices -- an expensive, time-consuming engineering effort," says Jay Baliga, Distinguished University Professor of Electrical and Computer Engineering at NC State and lead author of a paper on PRESiCE that will be presented later this month. "The companies can instead use the PRESiCE technology to develop their own products. That's good for the companies, good for consumers, and good for U.S. manufacturing." Power devices consist of a diode and transistor, and are used to regulate the flow of power in electrical devices. For decades, electronics have used silicon-based power devices. In recent years, however, some companies have begun using SiC power devices, which have two key advantages. First, SiC power devices are more efficient, because SiC transistors lose less power. Conventional silicon transistors lose 10 percent of their energy to waste heat. SiC transistors lose only 7 percent. This is not only more efficient, but means that product designers need to do less to address cooling for the devices. Second, SiC devices can also switch at a higher frequency. That means electronics incorporating SiC devices can have smaller capacitors and inductors -- allowing designers to create smaller, lighter electronic products. But there's a problem. Up to this point, companies that have developed manufacturing processes for creating SiC power devices have kept their processes proprietary -- making it difficult for other companies to get into the field. This has limited the participation of other companies and kept the cost of SiC devices high. The NC State researchers developed PRESiCE to address this bottleneck, with the goal of lowering the barrier of entry to the field for companies and increasing innovation. The PRESiCE team worked with a Texas-based foundry called X-Fab to implement the manufacturing process and have now qualified it -- showing that it has the high yield and tight statistical distribution of electrical properties for SiC power devices necessary to make them attractive to industry. "If more companies get involved in manufacturing SiC power devices, it will increase the volume of production at the foundry, significantly driving down costs," Baliga says. Right now, SiC devices cost about five times more than silicon power devices. "Our goal is to get it down to 1.5 times the cost of silicon devices," Baliga says. "Hopefully that will begin the 'virtuous cycle': lower cost will lead to higher use; higher use leads to greater production volume; greater production volume further reduces cost, and so on. And consumers are getting a better, more energy-efficient product." The researchers have already licensed the PRESiCE process and chip design to one company, and are in talks with several others. "I conceived the development of wide bandgap semiconductor (SiC) power devices in 1979 and have been promoting the technology for more than three decades," Baliga says. "Now, I feel privileged to have created PRESiCE as the nation's technology for manufacturing SiC power devices to generate high-paying jobs in the U.S. We're optimistic that our technology can expedite the commercialization of SiC devices and contribute to a competitive manufacturing sector here in the U.S.," Baliga says. The paper, "PRESiCE: PRocess Engineered for manufacturing SiC Electronic-devices," will be presented at the International Conference on Silicon Carbide and Related Materials, being held Sept. 17-22 in Washington, D.C. The paper is co-authored by W. Sung, now at State University of New York Polytechnic Institute; K. Han and J. Harmon, who are Ph.D. students at NC State; and A. Tucker and S. Syed, who are undergraduates at NC State. The work was supported by PowerAmerica, the Department of Energy-funded manufacturing innovation institute that focuses on boosting manufacturing of wide bandgap semiconductor-based power electronics. ref.KY56-PZTA06KY41-SL12T1G

A team of University of Wisconsin-Madison engineers has created the most functional flexible transistor in the world -- and with it, a fast, simple and inexpensive fabrication process that's easily scalable to the commercial level. It's an advance that could open the door to an increasingly interconnected world, enabling manufacturers to add "smart," wireless capabilities to any number of large or small products or objects -- like wearable sensors and computers for people and animals -- that curve, bend, stretch and move. Transistors are ubiquitous building blocks of modern electronics. The UW-Madison group's advance is a twist on a two-decade-old industry standard: a BiCMOS (bipolar complementary metal oxide semiconductor) thin-film transistor, which combines two very different technologies -- and speed, high current and low power dissipation in the form of heat and wasted energy -- all on one surface. As a result, these "mixed-signal" devices (with both analog and digital capabilities) deliver both brains and brawn and are the chip of choice for many of today's portable electronic devices, including cellphones. "The industry standard is very good," says Zhenqiang (Jack) Ma, the Lynn H. Matthias Professor and Vilas Distinguished Achievement Professor in electrical and computer engineering at UW-Madison. "Now we can do the same things with our transistor -- but it can bend." Ma is a world leader in high-frequency flexible electronics. He and his collaborators described their advance in the inaugural issue of the journal Flexible Electronics. Making traditional BiCMOS flexible electronics is difficult, in part because the process takes several months and requires a multitude of delicate, high-temperature steps. Even a minor variation in temperature at any point could ruin all of the previous steps. Ma and his collaborators fabricated their flexible electronics on a single-crystal silicon nanomembrane on a single bendable piece of plastic. The secret to their success is their unique process, which eliminates many steps and slashes both the time and cost of fabricating the transistors. "In industry, they need to finish these in three months," he says. "We finished it in a week." He says his group's much simpler high-temperature process can scale to industry-level production right away. "The key is that parameters are important," he says. "One high-temperature step fixes everything -- like glue. Now, we have more powerful mixed-signal tools. Basically, the idea is for flexible electronics to expand with this. The platform is getting bigger." Ref.KY56-2SA1860KY45-EKMC1601113

Today I want to share an LED strobe design project I found in electronic-lab, which you can do it by yourself. Strobe provides regular flashes of light. Usually Strobes are designed using Xenon Tubes. Here is LED based simple solution that can be used as strobe for entertainment and events and also as warning signals. Project is based on PIC16F1825 micro-controller with two digit frequency display. Project provides TTL output signal, frequency 1Hz-25Hz, Tact switches provided to set the frequency. This project works along with DC Output Solid State Relay Features 1.Supply 4.5 to 5V DC2.Frequency 1Hz To 25Hz3.Easy Interface with Relay Board4.Easy Interface with Solid State Relay5.On Board Power LEDOn Board Output LED6.Onboard Switch to set the frequency7.2X7 Segment 0.5 Inch Display Applications 1.Strobe for Entertainment2.Traffic Signal3.Warning Signal4.Ambulance Warning Signals Schematic   Parts List Connections Photos Working Diagram Ref.PIC16F1825 

A Tomsk Polytechnic University study reveals how topological vortices found in low-dimensional materials can be both displaced and erased and restored again by the electrical field within nanoparticles. This may open exciting opportunities for memory devices or quantum computers in which information will be encrypted in the characteristics of topological vortices.(Vortices in nanoparticles exposed by the electrical field. Credit: Tomsk Polytechnic University (TPU))Scientists from TPU and international collaborators have discovered unusual self-organization of atoms in the volume of nanoparticles and have learned to control it via an electric field. Such controlled nanoparticles can be used to generate capacious non-volatile random access memory (NRAM), quantum computers and other next-generation electronics. The main author is Dmitriy Karpov, engineer of the Department of General Physics, TPU, who explains that in modern materials science, the defects of matter are divided into two large groups. The first group includes classical, well-studied defects, when atoms in matter are mechanically disordered, i.e., atoms are either removed or inserted into the lattice. In the other group, the spatial organization of the lattice itself changes and such defects are called topological. Topological defects can strongly influence matter, making it superfluid or superconductive, and therefore, it is very important to study them. Topological defects can be found only in low-dimensional materials—two-dimensional nanorods and nanofilms (just several atoms thick) and one-dimensional nanodots or nanoparticles, which are spherical particles consisting of several tens or hundreds of identical atoms. "One of the important topological defects is a topological vortex which looks like a discernible twisting caused by a small displacement of all atoms. The vortex core is a nanostrand which can be both displaced by the field, and erased and restored again within nanoparticles," explains Edwin Fohtung, Professor of Los Alamos National Laboratory and New Mexico State University . The scientists studied barium titanate nanoparticles whose internal structure was visualized with the help of penetrating X-ray radiation from the synchrotron Advanced Photon Source (Chicago, USA). They obtained an image of the volume of nanoparticles with a resolution of 18 nanometers, which enabled them to analyze the slightest changes in the structure. As a result, the researchers showed that an external electric field can displace the core of the topological vortex inside the nanoparticle, and when the field is removed, it returns to its original position. Modern components of electronics are gradually becoming smaller. This can significantly influence the efficiency of devices, which will be significantly reduced due to quantum effects. One way to circumvent these limitations is to use topological vortices. Thus, they can be used to generate high density NRAM or quantum computers in which information will be encrypted in the characteristics of topological vortices. "All in all, the possibility to control and adjust topological vortices in nanoparticles is important for the creation of new electronics," concludes Dmitriy Karpov. Further reading>>>Topological defectA topological defect can be proven to exist[when?] because the boundary conditions entail the existence of homotopically distinct solutions. Typically, this occurs because the boundary on which the conditions are specified has a non-trivial homotopy group which is preserved in differential equations; the solutions to the differential equations are then topologically distinct, and are classified by their homotopy class. Topological defects are not only stable against small perturbations, but cannot decay or be undone or be de-tangled, precisely because there is no continuous transformation that will map them (homotopically) to a uniform or "trivial" solution. Reference>>>KY259-BB910KY259-CXA1512MKY32-K9T1G08U0M-YIBO 

Today I want to share a project of making a simple automatic street light controller using relay and LDR I found in circuitdigest with you.   You have seen street light which automatically gets turned on in the night and gets turned off in the morning or day time, there are sensors who senses the light and control the light accordingly. These Street lights are an important project in smart cities.   So here in this project, we are going to make a Simple Automatic Street Light Controller Using Relay and LDR. This circuit is very simple circuit and can be built with Transistors and LDR, you don’t need any op-amp or 555 IC to trigger the AC load. Here we have used an AC bulb as street light. Some applications of this circuit are street light controlling, home/office light controlling, day and night indicators, etc.   Components Required:   Transistor BC547 -2 LDR (Light Dependent Resistor) Relay Resistor 1k 100k Potentiometer Power Supply 12v -1 Connecting wires Jumper wires Screw terminal Block 2 pin or 3 pin Bread Board or Perf Board 1n4007 Diode AC supply AC Load or Bulb   Here you may want to know: what is LDR? LDRs are made from semiconductor materials to enable them to have their light sensitive properties. There are many types but one material is popular and it is cadmium sulphide (CdS). These LDRs or PHOTO REISTORS works on the principle of “Photo Conductivity”. Now what this principle says is, whenever light falls on the surface of the LDR (in this case) the conductance of the element increases or in other words the resistance of the LDR falls when the light falls on the surface of the LDR. This property of the decrease in resistance for the LDR is achieved because it is a property of semiconductor material used on the surface. LDR (Light Dependent Resistor)   Circuit Diagram and Explanation:   Below is the circuit diagram of this Light sensing Street Light:       In this project, we have used an LDR (Light Dependent Resistor) which is responsible for detecting light and darkness. The resistance of LDR increases in darkness and reduces in presence of light. This circuit is same as a Dark Detector or Light Detector Circuit, only here we have replaced simple LED with a AC load, using a Relay. Two BC547 NPN transistors are used to drive the relay. Automatic Street Light circuit using LDR and relay   Whenever light falls over LDR its resistance get decreased and transistor Q1 turns ON and collector of this transistor goes LOW, and this makes the second transistor turns OFF due to getting a LOW signal at its base, so relay also remain turned OFF due to second transistor.   Now whenever LDR senses Darkness, mean no light, then transistor Q1 turned ON due to increase in the resistance of LDR which is responsible for voltage drop at the base of Q1. Due to a LOW signal at the Q1 base, Q2 transistor gets a HIGH signal from the collector of Q1 and turns ON the relay. Relay turned ON the AC load that is connected to relay. A 10K pot is also used for setting up the sensitivity of the circuit.   So this is how automatic Street Lights turns on in the night and turn off in the day, and below is the effect pictures. >>>>>                                                       > >>>>   Ref. KY56-BC547A KY32-1N4007