The Kynix Blog - Resistors

IntroductionThe transistor is one of the basic semiconductor components, which has the function of current amplification in electronic circuit. It is made of two PN junctions very close to each other on a semiconductor substrate. Two PN junctions divide the entire semiconductor into three parts: The middle part is the base area, and the two sides are the emitter and the collector. What is NPN Transistor? For BeginnerCatalogIntroductionⅠ NPN Transistor Arrangement and SymbolⅡ How Do NPN Transistors Work?Ⅲ NPN Transistor Uses: A Controllable ValveⅠ NPN Transistor Arrangement and SymbolBefore explaining the principle, let's first understand the basic structure and symbols of the NPN transistor. To identify the NPN transistor pins, it will be Collector (c), Base (b) and Emitter (e).Figure 1. NPN Transistor Structure and SymbolNPN transistor is composed of two N-type semiconductors and one P-type semiconductor. Generally, an NPN transistor has a piece of P-type silicon (the base) sandwiched between two pieces of N-type (the collector and emitter). The arrangement is shown in the Figure 1. Ⅱ How Do NPN Transistors Work?Here is the main description to illustrate the basic principle and function of NPN transistors.1) Current AmplificationThe following analysis is only for NPN silicon transistors. As shown in the figure above, we call the current flowing from the base B to the emitter E the base current Ib; the current flowing from the collector C to the emitter E is called the collector current Ic. The directions of these two currents are both flowing out of the emitter, so an arrow is used on the emitter E to indicate the current direction.The amplification function of the transistor is: the collector current is controlled by the base current (assuming that the power supply can provide a large enough current to the collector), and a small change in the base current will cause a large change in the collector current: the change in the collector current is β times the change in the base current, that is, the current change is amplified by β times, so we call β the magnification of the transistor (β is generally much larger than 1). If we add a changing small signal between the base and the emitter, it will cause a change in the base current Ib. After the change in Ib is amplified, it leads to a big change in Ic. If the collector current Ic flows through a resistor R, it can be calculated according to the Ohm's Law formula U=R*I, and the voltage on this resistor will change greatly. According to the voltage on this resistor, so we can get the amplified voltage signal. In short, the change satisfies a certain proportional relationship.2) Bias CircuitWhen the transistor is used in the actual amplifier circuit, it is also necessary to add a suitable bias circuit. There are several reasons for this. First of all, due to the non-linearity of the transistor's BE junction (equivalent to a diode), the base current must be generated after the input voltage reaches a certain level (for silicon tubes, 0.7V is often used). When the voltage between the base and the emitter is less than 0.7V, the base current can be considered as zero. However, in practice, the signal to be amplified is often much smaller than 0.7V. If no bias is applied, such a small signal is not enough to cause a change in the base current (because when it is less than 0.7V, the base current is all 0).Add a suitable current to the base of the transistor (called the bias current, and the resistor in the figure used to provide this current, is called the base bias resistor). When a small signal follows this bias current are superimposed together, a small signal will cause a change in the base current, and the change in the base current will be amplified and output on the collector. Another reason is meeting the requirement of the output signal range. If there is no bias, then only those increased signals will be amplified, but the decreased signals will be invalid (because the collector current is 0 when there is no bias, and it cannot be reduced). With bias, let the collector have a certain current in advance. When the input base current becomes smaller, the collector current can be reduced; when the input base current increases, the collector current increases. Both the reduced signal and the increased signal can be amplified.3) NPN Transistor SwitchLet's talk about the saturation mode of the transistor. As shown in the figure above, because of the limitation of resistance Rc (Rc is a fixed value, then the maximum current is U/Rc, where U is the power supply voltage), the collector current cannot increase indefinitely. When the base current increases and the collector current cannot continue to increase, the transistor enters a saturated state. The general criterion for judging whether the transistor is saturated is: Ib*β>Ic.In a saturation state, the voltage between the collector and the emitter of the transistor will be very small, which can be understood as a switch. In this way, when the base current is 0, the collector current is 0 (this is called the triode cut-off), which is equivalent to the switch off; when the base current is large, it is equivalent to the switch on. In cut-off and saturation state, a transistor is equal to a switch.4) Operational StateIf we replace the resistor Rc with a bulb in the above figure, then when the base current is 0, the collector current is 0, so the bulb is off. If the base current is relatively large (greater than the current flowing through the bulb divided by the magnification β), the transistor will saturate, and the bulb will light up. Since the control current only needs to be a little larger than β of the bulb current, a small current can be used to control the on and off of a large current. If the base current increases slowly, the brightness of the bulb will also increase (which is a saturation process).The figure below is a basic transistor switch circuit. The base should connect a base resistor (R2), and the collector connects with a load resistor (R1).Operational ModeNPNCut-offUne<UonUc>UbActiveUbe>UonUc>UbSaturationUbe>UonUc<UbNPN transistor uses the B-E current (IB) to control the C-E current (IC). The E pole has the lowest potential, and usually the C pole has the highest potential during normal amplification, that is, VC>VB>VE.NPN base extremely high voltage, the collector and emitter are short-circuit and low-voltage, and the collector and emitter are open-circuit.NPN is suitable for two situations:If the input is a high level and the output needs a low level, NPN is better.If the input is a low level and the output needs a high level, NPN is better.2N2222 NPN Transistor PinoutⅢ NPN Transistor Uses: A Controllable ValveNPN is a component that uses b (base) current Ib to drive the current Ic flowing through CE, and its working principle is much like a controllable valve.Figure 2. A Controllable ValveThe blue water flow in the thin pipe on the left impacts the lever to open the valve of the large water pipe, allowing the larger red water flow to pass through the valve. The larger the blue water flow, the greater the red water flow in the big pipe. If the magnification is 100, then when the blue water flow is 1 kg/hour, then 100 kg/hour of water is allowed to flow through the large pipe. The principle of the transistor is the same. When Ib (base current) is 1mA, a current of 100mA is allowed to pass through Ice.Figure 3. NPN Transistor DiagramLet's analyze this circuit. If its magnification is 100, and ignore the base voltage. The base current is 10V÷10K=1mA, so the collector current should be 100mA. According to Ohm's law, the voltage on Rc is 0.1A×50Ω=5V. Then the remaining 5V is on the C and E poles of the transistor. Now if we let Rb be 1K, then the base current is 10V÷1K=10mA, according to the magnification of 100, is Ic 1000mA? If it is really 1A, then the voltage on Rc is 1A×50Ω=50V. The power supply voltage has been exceeded, and the transistors have become generators? This is not the case. See below:Figure 4. NPN Transistor Compared to A ValveContinue the metaphor. When the control current is 10mA, the valve on the main water pipe is opened to allow 1A current to flow, but can 1A be realized? No, because there is a resistor on it, it is equivalent to a fixed valve. It is stringed on top of the main water pipe. When the opening of the lower controllable valve is greater than the opening of the upper fixed resistor, the water flow will not increase any more, but will be equal to the water flow passing through the fixed valve opening above. Therefore, it is useless to open the lower transistor to a large opening. Therefore, we can calculate the maximum current of the fixed resistor 10V÷50Ω=0.2A, which is 200mA. That is to say, in the circuit, the base current increases and the collector current also increases. When the base current Ib increases to 2mA, the collector current increases to 200mA. When the base current increases again, the collector current will no longer increase, and it will not move at 200mA. At this time, the upper resistor also acts as a current limiter.  Let us understand the status of the IO in the microcontroller.Figure 5. AT89S51/52 The circuits with 24 IO ports of P1-P3 in the single-chip microcomputer are as shown in the figure above. Usually the purpose of using electronic circuits is to allow devices to obtain a certain current to make them work. For example, to make light-emitting diodes bright, a current of more than 1mA is generally required. However, the single-chip microcomputer is a smart chip. It can make logical analysis and judgments by detecting the voltage value of each IO port, and outputs high or low voltage as the result signal. Therefore, it can be seen that the IO ports of the single-chip microcomputer focus on voltage, not the current flowing through R and the transistor. Here what is the relationship between the voltage and current of the IO port in the single-chip microcomputer?  Continue the water pipe example.Suppose we let the valve of R open larger and let the control valve below be fully closed. At this time, as shown in Figure 6, it can be seen that the pressure at point P is the same as the water tank. When we fully open the following control valve, as shown in Figure 7, the water will flow through the pipeline with a large flow, and the pressure at point P is 0 at this time. This principle is very similar to electronic circuits. The logic quantity measured at the output point P is 1 (power supply voltage) or 0 (0 potential) by transistor turning off or on. However, there is a problem with this process, that is, when the output of point P is required to be 0, the transistor will be turned on very large, and the current flowing through it will be very large. There are 32 IO ports on the single-chip microcomputer, which consumes a lot of power. Look at Figure 8. If we close the upper valve R very small and close the lower control valve fully, then the pressure at point P will still the same as the water tank, which is the same as in Figure 6 above. When we open the control valve greatly, as shown in Figure 9, although the pressure at point P is also 0, the flow of water passing through at this time is greatly reduced. In this way, we can either output 1 or 0. So very little water is consumed. The circuit in the single-chip microcomputer does exactly this. The resistance R on it is about 50K, and the maximum current is 5V÷50K=0.1mA. In other words, when P outputs 1, no current is consumed, and when P outputs 0, the current consumed is 0.1mA. Because of its large pull-up resistance R, for beginners, it is necessary to have certain methods to directly drive LEDs or other loads. Here to share the various situations when the IO port is connected to the load.Figure 10. AT89S51/52 & 74HC373Let's take a look at the situation of connecting TTL devices first. When P1.0 is connected to an input pin of 74HC373, and the input impedance of TTL is very high, about a few hundred K to M ohm level. We assume 500K resistor to P1.0 to ground. In this way, when the transistor is turned on, the P1.0 point is at a low level, and a current of 0.1mA flows through Rc and then through the transistor to the ground, and no current flows through Ri. When the transistor is cut off, the current flows through Rc and then flows to the ground through Ri. Due to the resistor voltage divider effect, there are partial voltages on Rc and Ri, and the voltage at point P1.0 is the divided voltage of Rc and Ri. Total current is 5V÷(50K＋500K)=0.009mA, then the voltage at point P1.0 is 0.009mA×500K=4.5V. TTL stipulates that output 2.4~5V is high level. So this connection is correct. Now let's take a look at the situation of using S51 to drive the LED.AT89S51 Correct ConnectionLet’s take a look at the situation in Figure 11. Obviously, only P1.0 is a high potential to light the luminous tube, so the transistor must be cut off. In this case, the current flows through Rc to the luminous tube and then to the ground. To make the luminous tube turn on, there must be a threshold voltage exceeding 2.1V at both ends of the luminous tube. Therefore, the current flowing through the luminous tube is (5V-2.1V)÷50K=0.058mA, which is too weak to conduct.Look at Figure 12. It can be seen from the figure that P1.0 must be at a low potential if the luminous tube turned on. The transistor of the P1.0 port must be turned on. At this time, the current flows all the way through Rc to the transistor and then to the ground. The other way consumes 2.1V on the luminous tube. Then current flows through with almost no resistance, but the maximum current of the triode of the IO port cannot exceed 15mA. If it exceeds, the triode will be burned out, so this connection method is incorrect. So how can these two connections be able to drive the light-emitting tube? See below: AT89S51 Incorrect ConnectionLooking at Figure 13, a resistor Ri is connected between P1.0 and Vcc. When the transistor is turned on, two currents will flow through its c, e pole, one is the 0.1mA current on the internal R, and the other is the current on Ri. In order to prevent the transistor from over-current and burn out, we must make sure the resistance value, Ri=5V÷15mA=0.333K, which is about 330 ohms. At this time, the current flowing through the transistor is about 15mA, and the light-emitting tube is not bright at this time. When the transistor is turned off, both currents will flow through the luminous tube. The current flowing through the internal resistance of S51 is (5V-2.1V)÷50K=0.06mA, which is so small that we can ignore it. The current flowing through Ri is (5V-2.1V)÷330Ω=0.0087A, which is 8.7mA. However, the current consumed when the luminous tube is off is greater than the current consumed when the luminous tube is on. If many IO ports are used to light up many LEDs, such a circuit is not economical.Look at Figure 14, after connecting a resistor in series with the luminous tube between Vcc and P1.0. When the transistor is turned on, the two currents will flow through the c, e after confluence. The current on the internal resistance is still 0.1mA. The current on the ce should be less 15mA. If exceeds 15mA, the resistance is determined as (5V-2.1V) ÷ 15mA = 0.193K, which is about 200 ohms. In this way, the current flowing through the luminous tube is about 15mA, and the luminous tube is on. When the transistor is cut off, it blocks the paths of these two currents, so no current is consumed. Low level P1.0 directly drives the light-emitting tube. It can be seen that this circuit consumes 15mA of current when the light-emitting tube is on, and does not consume current when it is off, so this circuit is effective. S51 direct drive digital tube generally also uses this principle. Frequently Asked Questions about NPN Transistor1. What is meant by NPN transistor?An NPN transistor is the most commonly used bipolar junction transistor, and is constructed by sandwiching a P-type semiconductor between two N-type semiconductors. An NPN transistor has three terminals– a collector, emitter and base. The NPN transistor behaves like two PN junctions diodes connected back to back. 2. How do NPN transistors work?The NPN transistor is designed to pass electrons from the emitter to the collector (so conventional current flows from collector to emitter). The emitter "emits" electrons into the base, which controls the number of electrons the emitter emits. ... The transistor is kind of like an electron valve. 3. What is a NPN transistor used for?NPN transistors are mainly used in switching applications. Used in amplifying circuit applications. Used in the Darlington pair circuits to amplify weak signals. NPN transistors are used in the applications where there is a need to sink a current. 4. Which is better PNP or NPN transistor?A NPN transistor has electrons as majority charge carriers whereas the PNP transistor has holes as majority charge carrier. ... mobility of electrons is more than hole,so as a result npn transistor are faster than pnp that's why they are preferred. 5. What does NPN mean?NPN stands for Negative, Positive, Negative. Also known as sinking.

IntroductionA three-phase circuit consists of a three-phase source, a three-phase load, and a three-phase transmission line. The most basic characteristic of this circuit is that it has one or more groups of power supplies. Each group consists of three sinusoidal power supplies with the same amplitude, the same frequency, 120° phase difference, and the power supply and the load are connected in a specific way. Three-phase circuits are widely used in power systems such as power generation, transmission, distribution, and high-power electrical equipment.What does 3 phase mean?CatalogIntroductionⅠ Three-phase Circuit Basics1.1 Three-phase Circuit Characterized1.2 Three-phase Circuit Terms1.3 Three-phase Voltage & Current1.4 Three-phase Circuit AdvantagesⅡ Symmetrical vs Asymmetrical2.1 Symmetrical Three-phase Circuit2.2 Three-phase AsymmetryⅢ Power in Three Phase Circuit FormulasⅣ Frequently Asked Questions about Three-phase CircuitⅠ Three-phase Circuit BasicsThe three phases could be supplied over six wires, with two wires reserved for the exclusive use of each phase. However, they are generally supplied over only three wires, and the phase or line voltages are the voltages between the three possible pairs of wires. The phase or line currents are the currents in each wire. Voltages and currents are usually expressed as rms or effective values, as in single-phase analysis.1.1 Three-phase Circuit CharacterizedSpecial power supplySpecial loadSpecial connectionSpecial solution1.2 Three-phase Circuit Terms1) End wire (fire wire)2) Neutral line3) Line current4) Line voltage5) Phase current6) Phase voltage7) Three-phase three-wire system and three-phase four-wire system1.3 Three-phase Voltage & CurrentStar ConnectionSummery: Line Voltage vs Phase Voltage1) The line current is equal to the corresponding phase current.2) If the phase voltage is symmetrical, the line voltage is also symmetrical.3) The line voltage is equal to √3 times the phase voltage.4) The phase of the line voltage leads the corresponding phase voltage by 30°. Delta ConnectionSummery: Line Current vs Phase Current1) The line voltage is equal to the corresponding phase voltage.2) If the phase currents are symmetrical, the line currents are also symmetrical.3) The line current is equal to √3 times the phase voltage.4) The phase of the line current lags behind the corresponding phase voltage by 30°.1.4 Three-phase Circuit AdvantagesPower generation: Three-phase power is increased by 50% compared to single-phase power.Transmission: 25% less material than single-phase circuit transmission. That is, under certain conditions, transmitting a certain amount of power by three-phase only requires 75% of the copper of single-phase transmission.Power distribution: More economical than single-phase transformers and easier to connect to the load.Transportation: simple structure, low cost, reliable operation, convenient maintenance.In addition, three wires are usually seen in high-voltage transmission lines, whether on towers or poles, with pin or suspension insulators. Some high-voltage lines are now DC, since solid state devices make it easier to convert to and from AC. The DC lines are free of the problems created by phase, as well as eliminating the skin effect that reduces the effective area of the conductors. It is not nearly as easy to manage long-distance electrical transmission as might be thought.Ⅱ Symmetrical vs Asymmetrical2.1 Symmetrical Three-phase CircuitA symmetrical three-phase power source is usually generated by a three-phase synchronous generator, as shown in Figure (a). Among them, the three-phase windings differ by 120° in space. When the rotor rotates at a uniform angular velocity ω, an induced voltage is generated in the three-phase winding, thereby forming a symmetrical three-phase power supply as shown in Figure (b). Among them, the three ends of A, B, and C are called the start end, and the three ends of X, Y, and Z are called the end. When you connect a load to the three wires, it should be done in such a way that it does not destroy the symmetry.Instantaneous Voltage Calculation of Three-phase PowerIn the formula, take the phase A voltage uA as the reference sine quantity. The three-phase voltage waveform diagram is shown in Figure (a).The key to understanding three-phase is to understand the phasor diagram for the voltages or currents. The phasor of the three-phase power supply can be represented by the Figure (b).The characteristics of the symmetrical three-phase power supply can be derived from the above formula:From the above formula, the sum of the instantaneous value of the three-phase power supply and the sum of the phasor are always zero.The sequence in which each phase of the three-phase power passes through the same value (such as the maximum value) is called the phase sequence of the three-phase power, and the phase sequence of the above-mentioned three-phase voltage is called the positive sequence. Conversely, if phase B exceeds 120° of phase A and phase C exceeds 120° of phase B, this phase sequence is called reverse sequence. If there is no special instructions, it will generally default to positive order.2.2 Three-phase Asymmetry1) In a three-phase circuit, as long as there is asymmetrical part, it is called a three-phase asymmetry.2) The complex power absorbed by the three-phase load is equal to the sum of various complex powers.3) The instantaneous power of a three-phase circuit is the sum of the instantaneous power of each phase load.4) In a three-phase three-wire circuit, whether symmetrical or not, two power meters can be used to measure three-phase power.When the power supply voltage in the three-phase circuit is asymmetrical or the parameters in the circuit are asymmetrical, the current in the circuit is generally asymmetrical. This kind of circuit is called three-phase asymmetry. There are a lot of asymmetry parts in three-phase circuits, and the causes are different. For example, there are many low-power single-phase loads in a three-phase circuit, it is difficult to make them into a completely symmetrical circuit. When a three-phase circuit is broken or short-circuited, it is also a three-phase asymmetry circuit. In addition, some electrical equipment and instruments formally use three-phase asymmetry to work.For example, the most common low-voltage three-phase four-wire system. Due to the large number of single-phase loads in the low-voltage system, the equivalent impedances ZA, ZB, and ZC of the three phases circuit are generally different from each other, and the power supply voltage can generally be considered symmetrical. In this way, a symmetrical three-phase power supply converts to an asymmetrical three-phase load.The circuit shown in the figure has two nodes, and the voltage between the two nodes can be directly calculated according to the node voltage method.Although the power supply voltage in the above formula is symmetrical, the voltage between the neutral point of the power supply and the neutral point of load is not zero due to the load asymmetry, that is, UNN≠0. According to Kirchhoff's voltage law, the phase voltage of the load can be obtained as:The phasor diagram of each voltage corresponding to the above formula is as follows:Ⅲ Power in Three Phase Circuit Formulas1. Average PowerSuppose the power absorbed by a phase load in a symmetrical three-phase circuit is equal to Pp=UpIpcosφ, where Up is the phase voltage and Ip is the phase current of the load. Then the total three-phase power is: P=3UpIpcosφPay Attention To1) φ in the above formula is the phase difference angle (impedance angle) of phase voltage and phase current.2) cosφ is the power factor of each phase, in a symmetrical three-phase system:cosφA=cosφB=cosφC=cosφ3) The formula calculates the circuit power (or the power absorbed by the load).When the load is in a star connection, the line voltage  and line current  at the load end are substituted into the above formula:When the load is in a delta connection, the line voltage  and line current  at the load end are substituted into the above formula:2. Reactive powerThe reactive power absorbed by the load in a symmetrical three-phase circuit is equal to the sum of the reactive power of each phase:3. Apparent Power4. Instantaneous PowerSuppose the voltage and current of phase A of the three-phase load are:Then the instantaneous power of each phase is:It can be proved that their sum isThe above formula shows that the instantaneous power of a symmetrical three-phase circuit is a constant, and is equal to the average power. This is one of the advantages of a symmetrical circuit. For example, on a three-phase motor, a balanced electromagnetic torque is obtained and mechanical vibration is avoided, which is not available in single-phase motors. Ⅳ Frequently Asked Questions about Three-phase Circuit1. What is a 3 phase circuit?Three-phase power is a three-wire ac power circuit with each phase ac signal 120 electrical degrees apart. ... three-phase is that a three-phase power supply better accommodates higher loads. Single-phase power supplies are most commonly used when typical loads are lighting or heating, rather than large electric motors. 2. How many wires are in a 3 phase?four wiresThe three-phase system has four wires. Three are conductors and one is neutral. 3. What is the 3 phase power formula?3-Phase Calculations. For 3-phase systems, we use the following equation: kW = (V × I × PF × 1.732) ÷ 1,000. 4. What is the advantage of three-phase system?A three-phase circuit provides greater power density than a one-phase circuit at the same amperage, keeping wiring size and costs lower. In addition, three-phase power makes it easier to balance loads, minimizing harmonic currents and the need for large neutral wires. 5. What is meant by 3 phase balanced load?A balanced three-phase voltage or current is one in which the size of each phase is the same, and the phase angles of the three phases differ from each other by 120 degrees. ... With such a balanced load, if a balanced three-phase supply is applied, the currents will also be balanced.

IntroductionA stable power supply is necessary for normal operation of the electrical system. Except for the use of solar cells or chemical batteries in certain special occasions, the direct current of most circuits is converted from the alternating current of the grid. The bridge rectifier is commonly used to convert AC into DC, which is the most commonly used circuit that uses the unidirectional conductivity of diodes for rectification. There are many types of bridge rectifiers: flat, round, square, bench-shaped (plug in and SMD), etc., having GPP and O/J structures. The maximum rectified current ranges from 0.5A to 100A, and the maximum reverse peak voltage ranges from 50V to 1600V.What is Bridge Rectifier?CatalogIntroductionⅠ Bridge Rectifier Diode CircuitⅡ Bridge Rectifier Circuit FeaturesⅢ Single Phase Rectification vs Three Phase Rectification3.1 Single Phase Bridge Rectifier Circuit3.2 Three Phase Bridge Rectifier CircuitⅣ Role of Bridge RectificationⅤ Bridge Rectifier Wiring DiagramⅥ Difference between Bridge Rectifier and Full-wave Rectifier CircuitⅠ Bridge Rectifier Diode CircuitThe bridge rectifier uses four semiconductor diodes to be connected in pairs. When the positive half of the input sine wave is turned on, the two tubes are turned on, and the positive output is obtained; on the contrary, when the negative half of the sine wave is input, the other two tubes are turned on. Since the two tubes are reversely connected, the output is still the positive part of the sine wave. In addition, the utilization efficiency of the input sine wave by the bridge rectifier is twice as high as that of the half-wave rectifier.The rectifier bridge stack is generally used in a full-wave rectifier circuit, and it is divided into a full bridge and a half bridge. The full bridge is composed of 4 rectifier diodes connected in the form of a bridge full-wave rectifier circuit and packaged as a whole. The half bridge is to seal the half of the two diode bridge rectifiers together. Two half bridges can form a bridge rectifier circuit, and a half bridge can also form a full wave rectifier circuit with a center tap of the transformer. When choosing a rectifier bridge, the rectifier circuit and operating voltage must be considered carefully.The forward current of the full bridge has various specifications such as 0.5A, 1A, 1.5A, 2A, 2.5A, 3A, 5A, 10A, 20A, 35A, 50A, etc. The withstand voltage (the highest reverse voltage) is 25V, 50V, 100V, 200V, 300V, 400V, 500V, 600V, 800V, 1000V, etc.In this chapter, the rectifier diode is regarded as an ideal component, that is, its forward conduction resistance is considered to be zero, and its reverse resistance is infinite, because of the convenience of analyzing the rectifier circuit. However, in practical applications, it should be considered that the diode has internal resistance, and the output amplitude of the waveform obtained after rectification will be reduced by 0.6~1V. When the input voltage of the rectifier circuit is large, this part of the voltage drop can be ignored. On the contrary, if the input voltage is small, for example, if the input is 3V, the output is only 2V, and the influence of the diode forward voltage drop needs to be considered.Current Direction of the Bridge Rectifier CircuitFigure 1.In the positive half cycle of u2, D1 and D3 are turned on, D2 and D4 are turned off, and the current returns from the upper end of the TR secondary to the lower end via D1→RL→D3, and a half-wave rectified voltage is obtained on the load RL.In the negative half cycle of u2, D1 and D3 are off, D2 and D4 are on, and the current returns from the lower end of Tr secondary to the upper end of Tr secondary via D2→RL→D4, and the other half-wave rectified voltage is obtained on the load RL. Ⅱ Bridge Rectifier Circuit Features(1) The rectification device used is twice that of full-wave rectification.(2) Rectified voltage pulse changing direction is the same as full-wave rectification.(3) The reverse voltage that each device bears is the peak value of the power supply voltage.(4) The utilization rate of the transformer is higher than that of the full-wave rectifier circuit. Ⅲ Single Phase Rectification vs Three Phase Rectification3.1 Single Phase Bridge Rectifier CircuitFigure 2.The single phase bridge rectifier circuit is composed of four diodes connected in the form of a bridge. Its disadvantage is that it only uses half a cycle of the power supply, and at the same time the rectification voltage has a large pulsation.The above Figure 2 (a) shows the direction of current in the single-phase bridge rectifier circuit. The solid arrow indicates the situation when the AC power supply is in the positive half cycle, and the dotted arrow indicates the situation when the AC power supply is in the negative half cycle.It can be seen that the four diodes are divided into two parts: positive half cycle and negative half cycle. However, the current direction on the load does not change. This is full-wave rectification. In addition, the single-phase bridge rectifier circuit can be implemented with an integrated device "bridge stack" in practice.In Figure 3. shows the waveform diagram of the single phase bridge rectifier circuit. According to the diagram, the average voltage is: Uo ≈ 0.9U2 (where U2 is the effective value of the output voltage of the transformer secondary side).Figure 3. Wave Form (single phase)3.2 Three Phase Bridge Rectifier CircuitFigure 4.The three phase bridge rectifier circuit is developed from a uncontrolled half-wave rectifier circuit, which is essentially a series connection of a set of common cathode and a set of common anode with three semiconductor diodes.In addition, the three phase bridge circuit must have two thyristors turned on at the same time, one in the common cathode area and the other in the common anode area to form a loop.Circuit Analysis LawThe diode with the highest anode potential in the common cathode group is turned on.The diode with the lowest cathode potential in the common anode group is turned on.Circuit Analysis ExamplesFigure 5. t1 ~ t2In the common cathode group, the potential at point U is the highest, and V1 is on.In the common anode group, the potential at point V is the lowest, and V4 is on.The voltage across the load is the line voltage Uuv. Figure 6. t2~t3In the common cathode group, the potential at point U is the highest, and V1 is on.In the common anode group, the potential at point W is the lowest, and V6 is turned on.The voltage across the load is the line voltage Uuw. Figure 7. t3~t4In the common cathode group, the potential at point V is the highest, and V3 is on.In the common anode group, the potential at point W is the lowest, and V6 is turned on.The voltage across the load is the line voltage Uvw.......SummeryIn a full-wave cycle, it can be divided into 6 intervals, each of which is powered by a pair of phase wires to the load.In a full-wave cycle, each diode is turned on for one-third of the time (the conduction angle is 120°).During the 6 periods in a cycle, the voltage of the load can be seen as a periodic change. Ⅳ Role of Bridge Rectification1. Convert the alternating current generated by the alternator into direct current to power the electrical equipment and charge the battery.2. Limit the battery current to flow back to the generator to protect the generator from being burnt out by the reverse current.Figure 8. Bridge Rectifier AC to DC Flow ChartⅤ Bridge Rectifier Wiring DiagramThe bridge rectifier circuit overcomes the shortcomings that the full-wave rectifier circuit requires the transformer secondary to have a center tap and the diode to withstand large reverse voltage, but two diodes are used. With the rapid development of semiconductor devices and low cost today, this shortcoming is not obvious, so bridge rectifier circuits are widely used in practice.It needs to be pointed out that the diode as a rectifier component should be selected according to different rectification methods and load values. If choose improperly, you may not be able to work safely, or even burn the pipe, causing waste.Figure 9. Schematic Diagram of Bridge Rectifier CircuitThe bridge rectifier circuit can also be considered as a kind of full-wave rectifier circuit. The transformer is connected to four diodes according to the method shown in Figure 9. D1～D4 are four identical rectifier diodes connected in the form of a bridge, so they are called bridge rectifier circuits. Using the guiding function of the diode, the secondary output can be directed to the load even in the negative half cycle. It can be seen from the figure that D1 and D2 lead the current through RL from top to bottom during the positive half cycle, and D3 and D4 lead the current through RL from top to bottom during the negative half cycle. In this structure, if the same DC voltage is output, the secondary winding of the transformer needs only half of the winding compared with the full-wave rectification. However, if the same amount of current is to be output, the diameter of the winding should be increased accordingly.Because the output voltage of the rectifier circuit contains larger pulsating components. In order to reduce the pulsation component as much as possible, on the other hand, it is necessary to keep the DC component as much as possible to make the output voltage close to the ideal DC. This measure is filtering. Filtering is usually achieved by using the energy storage effect of capacitors or inductors.Figure 10. Bridge Rectifier Circuit with CapacitorIn this experimental circuit, capacitor filtering is used, that is, a filter capacitor C is connected in parallel with the load resistance RL. The circuit is shown in Figure 11, and the filtered waveform is as shown in the figure below.Figure 11. Full-wave Rectification Filter WaveformThe DC component of the full-wave rectified output voltage (compared to the half-wave) is increased, and the pulsation is reduced, but the transformer needs a center tap, which is troublesome to manufacture, and the rectifier diode needs to withstand high reverse voltage, so it is generally suitable for the low output voltage.Figure 12. Half-wave Rectification Filter WaveformHalf-wave rectification is the most commonly used circuit that uses the unidirectional conductivity of a diode for rectification. Ⅵ Difference between Bridge Rectifier and Full-wave Rectifier Circuit1) Don't need a center tap on the secondary side of the bridge rectifier circuit transformer, but use 2 more rectifier diodes.2) The full-wave rectifier circuit uses less than 2 rectifier diodes, but the secondary side of the transformer should be center-tapped.3) The reverse withstand voltage of the rectifier diode used in the full-wave rectifier circuit is twice that of the bridge rectifier.4) Rectification and full-wave rectification have different requirements for the number of secondary transformers. The former requires only 1 set of coils, while the latter requires 2 sets.5) Rectification and full-wave rectification have different requirements for the secondary current of the transformer, the former is twice the latter. Frequently Asked Questions about Bridge Rectifier Circuit1. What does a bridge rectifier do?A bridge rectifier provides full-wave rectification from a two-wire AC input, resulting in lower cost and weight as compared to a rectifier with a 3-wire input from a transformer with a center-tapped secondary winding. ... Diodes are also used in bridge topologies along with capacitors as voltage multipliers. 2. How does a bridge rectifier convert AC to DC?Bridge rectifiers convert AC to DC using its system of diodes made of a semiconductor material in either a half wave method that rectifiers one direction of the AC signal or a full wave method that rectifies both directions of the input AC. 3. What happens when a bridge rectifier fails?Without capacitor smoothing, when 1 diode fails open in a bridge rectifier, both voltage and current reduce. With capacitor smoothing, when 1 diode fails open in a bridge rectifier, the voltage remains fairly constant but the current increases. 4. Why do we use 4 diodes in bridge rectifier?The bridge rectifier consisting of four diodes enables full wave rectification without the need for a centre tapped transformer. The bridge rectifier is an electronic component that is widely used to provide full wave rectification and it is possibly the most widely used circuit for this application. 5. Why is a bridge rectifier more preferable than a full wave rectifier?Bridge rectifier is driven by a single winding which carries current both cycles in load. ... Full wave is better than bridge in one more aspect i.e. the output DC voltage is slightly higher than bridge. This is because it has only 1 diode drop from AC to DC.

IntroductionUSB is very common, because it is indispensable for data transmission and charging. In modern life, we can see one or more USB ports on desktop computers, laptops, TVs, game devices, cars, media players, phones, and other electric devices, etc. USB devices are very important for our life. Look at your computer or smart phones, we probably know what it used for, however, fewer people know the full name of USB and what the real meanings of USB protocols and USB types.USB Ports, Cables, Types, & ConnectorsCatalogIntroductionⅠ Figure USB Ports and Standards OutⅡ USB Port Colors MeaningⅢ USB-C vs Type CⅣ USB 2.0 vs USB 3.0Ⅴ According to Labels Behind USB PortsHere are some easy steps to identify USB ports with different standards.Ⅰ Figure USB Ports and Standards OutUSB (universal serial bus) aims for input and output interfaces standard. It is widely used in information transformation products such as personal computers and mobile devices. The USB interface has hot-swappable, plug-and-play functions, and can be connected to a variety of external devices, such as a mouse and keyboard, etc. Our mobile phone charging uses the USB connector. These USB devices give us great convenience. USB chargers, USB connectors, USB hub, USB ports and USB cables, are all USB the same? What is USB 2.0 and USB 3.0? Low speed, full speed, and high speed mean what? What are Type-A, Type-B, and Type-C? Here you will get a full answer.Versions of USBThe USB 1.0/2.0/3.0 we often say refers to the technical specifications. The biggest difference among them is speed, that is, they indicate the speed of USB transfer files. The maximum transmission bandwidth of USB 3.0 is up to 5.0Gbps (640MB/s). Now many high-speed U disks or hard drives of portable electric devices use USB 3.0 or USB 3.1. USB also includes the old USB 1.1 standard and  USB 2.0 standard. The traditional maximum transfer rate of USB 1.1 is 12Mbps. Generally, manufacturers call its products that comply with the USB 1.1 standard as "full-speed USB." When the high-speed USB 2.0 was first introduced, the highest transmission rate was only 240Mbps. Later, the USB Promoter Group increased the rate to 480Mbps in October 1999, which is 40 times faster than the traditional USB 1.1. USB 2.0 is backward compatible with USB 1.1. Of course, USB 1.1 devices are "upward compatible" with USB 2.0, but they cannot reach the transmission speed of USB 2.0 and automatically stay at low speed. The maximum length of the USB 2.0 cable is 5 meters, but if five USB adapters are used, the maximum length can be up to 30 meters.Although you'll still be able to connect old-school devices with USB Type-A or USB Type-B connectors, but now you have more choices, that is USB4. USB4 is a USB system specified in the USB4 specification which was released in version 1.0 on 29 August 2019 by USB Implementers Forum. It leverages the Thunderbolt 3 protocol to deliver speeds up to twice as fast as the USB version it replaces. The USB4 architecture defines a method to dynamically share a single high-speed link with multiple end device types to best serve the transfer of data by type and application. USB-A, USB-B, and USB-C Port Types-Which is faster?Type-A/B/C determines the appearance of the USB ports. For example, the mouse, keyboard, USB flash drive and other interfaces we use are generally Type-A, which is also the most widely used interface. Type-B is more common in printers, monitors and other devices. In the past, Micro USB and Mini USB commonly used in mobile phones were portable versions of USB 2.0. The appearance of Type-C is very recognizable, slimmer. Its biggest feature is flippability, that is, USB-C connector has no up or down orientation, so you never have to flip it over to plug it in.1) Type-A: Standard USB PortType-A is the most common types of USB ports on computers. It has a notable feature: direction requirements. The connector (male port) must be inserted into the interface (female port) from a certain direction, in addition, because the appearance of the two sides of the USB male port is very close, this insertion process often makes mistakes.2) Type-B: Commonly used in printer equipmentType-B is the most common and popular data interface type on printers and displays, and some displays will also use it.3) Type Micro-B: USB standard for mobile devicesCurrently, most Android phones use the Micro USB interface (USB Micro-B), which is still widely used in various mobile portable devices.4) Type-C: It will become mainstreamAlthough Type-C has just appeared, it is foreseeable that as the USB Type-C technology matures, various notebooks, tablets and even smart phones in the future will begin to use the USB Type-C interface. Ⅱ USB Port Colors MeaningColorUSB ConnectorUSB Speed StandardNoteWhiteUSB-A or USB-B  Micro USB-AUSB 1.0 or USB 1.1*BlackUSB-A or USB-B Micro USB-BUSB 2.0 Hi-Speed*BlueUSB-A or USB-BUSB 3.0 Super Speed*RedSleep-and-Charge USB-AUSB 3.1 Gen 2 USB 3.2Usually denotes an "always on" portYellowSleep-and-Charge USB-AUSB 2.0 or USB 3.0Higher power or "always on" portⅢ USB-C vsType CThe Type-C is the same as the USB C, because the USB C is also called USB Type-C. However, there are slight differences between them. Let’s look at the following facts.Features of USB-C Connector:1. Ultra-thinThe old USB port size is 14mm * 6.5mm, while the USB-C is only 8.4mm * 2.6mm.2. No OrientationLike the Lightning, there will be no problem regardless of whether it is plugged in or reversed. It claims to be able to up to 10,000 times of repeated plugging and unplugging.3. Fast Transfer RateThe maximum transfer rate of the USB-C port is 10Gb per second, which is much faster than USB 3.0.4. Two-way TransmissionUnlike the old USB port, the power can only be transmitted in one direction. The USB-C port is bidirectional, so it can have two transmission power ways. Therefore, users can not only use laptops to charge mobile devices, but also use other devices or mobile power sources to charge laptops.5. Strong Power Supply CapabilityThe standard specification cable equipped with Type-C connector can pass 3A current, and it also has a super USB power supply capacity, which can up to 100W of power.6. Backward CompatibilityUSB-C can be compatible with the old USB protocol, but users need an additional adapter.USB-C refers to the Type C port that uses the USB 3.1 standard, but it should be noted that USB-C is not equal to Type C. Because there are many Type C devices that can only reach USB 2.0 or USB 3.0 transfer rate.With the improvement of technology, Type-C also supports the USB3.1 standard. Because the voltage and current increase, the coding consumption is reduced, from 20% of USB 3.0 to 3%. In other words, users can quickly transfer data and video through Type-C, or charge faster. Also users can charge other devices with their mobile phones. As for the display, when using Type-C for data transmission, there is no need to use another power cord to power the display, which solves the problem of messy desktop cables. Even the relatively high-end HDMI and DP ports cannot do it.The USB-C connector can be expanded into three: power supply/ USB transmission/ VGA or HDMI, which is the next-generation mainstream USB interface. The type-c cable is also of great help to the arrival of the 5G. Because the port of it becomes smaller, the flattening of electronic products is promoted. And in the transmission of audio and video, the tc data line has faster speed. At present, well-known technology manufacturers such as Sony and Apple have widely used type-c cables on their electrical devices because they can support multiple formats and reduce the limitations of USB. In short, the arrival of the 5G actually wants everyone to experience faster bandwidth, so the corresponding supporting facilities should also keep up. The type-c cable is undoubtedly one of them. Ⅳ USB 2.0 vs USB 3.0Although USB has developed to the USB3.1 protocol, we often see two types of USB 2.0 and USB 3.0 on devices. How do we distinguish these two interface types in daily use? Some people will say that USB 3.0 port is blue and USB2.0 port is black, which is easy to distinguish. In fact, it is not. Even though most USB3.0 ports use blue, there are many special cases. Here are some examples. The color of the USB ports on some models does not have any special treatment, and it looks no different from USB 2.0 type, and it is all black. However, it is often marked with "SS" in front of the logo. "SS" is the abbreviation of "SuperSpeed USB", which means connector or port that uses the USB 3.0 standard. The black USB type is also suitable for USB 3.0. The USB ports in Apple's new MacBook notebooks are all USB 3.0 standard, but in order to keep in harmony with the color of the computer cover, a white connector design is adopted. The USB ports on the Razer gaming notebooks are also USB 3.0, but in order to match the bright green keyboard backlight on the body and the Razer logo, the color of the USB port adopts "green". It improves the recognition of the machine and the brand, because no third-party manufacturer has adopted a green USB interface design. In addition, distinguish the metal pins of the USB ports. Generally, USB 2.0 uses a row of 4 pins, while USB 3.0 has a two-row pin design, with 5 pins in the front row and 4 pins in the back row. In addition, there is also a hybrid port of eSATA and USB 2.0, which can plug in both USB devices and eSATA interface devices. However, they are common in business models of previous years. Ⅴ According to Labels Behind USB Ports"+" sign - It represents the USB interface with high current output capability. The ordinary USB interface provides a maximum current of 500mA, but it may not be able to drive when encountering "high energy consumption" devices such as mobile hard disks and USB optical drives. Therefore, when it appeared, the output current on this interface can reach 1000mA (1A), which greatly enhances the drive capability."SS" - It is actually a symbol of USB 3.0. If the USB port has “SS” (or “SuperSpeed”) on its label, it’s a USB 3.0 port. If it’s“SS 10”, it’s a USB 3.1 port."Lightning Logo" -It generally appears on notebooks, and the USB port with it has a power-off charging function. That is, it can use its own battery or an external power supply to charge the mobile device when it is turned off. The lightning mark with an arrow indicates the Thunderbolt 3: two-way charging and two-way data transmission. Thunderbolt 3 supports for up to 40Gbps of throughput, alongside reduced power consumption and the ability to move as much as 100 watts of power over the interface. And it also means that a single cable is all you need to push power and transfer a large amount of information (up to and including video data for two 60Hz 4K displays) to and from even a complex device like a computer, something many laptop manufacturers have been quick to take advantage of.USB is an important interface on the computer. Almost 90% of the external devices are connected by it for mobile hard drives, such as U disks, printers, etc. Understanding the above information can analyze and solve the most common problems of unrecognized external devices of USB. At the same time, it is also very useful for us to choose USB products. Ⅵ Frequently Asked Questions about USB Types and USB Versions1. What are the different types of USB ports?Types of USB Ports and ConnectorsUSB-AUSB-BUSB-B MiniUSB-B MicroUSB-CLightning 2. How can I tell the difference between USB 2.0 and 3.0 ports?You can generally tell the difference between USB 1.0, 2.0, and 3.0 by color alone. While the size and shape may be identical, the key is to look at the color of the plastic inside the device. The USB 1.0 features a white plastic color, while USB 2.0 is black, and the USB 3.0 is blue. 3. What is the difference between USB Type A and C?The USB-A has a much larger physical connector than the Type C, Type C is around the same size as a micro-USB connector. ... The beauty of Type C is that it can be inserted any way up as the connector pins are the same on either side. 4. Are USB 2.0 and 3.0 ports the same?The A connectors still work properly so any 2.0 device with a 2.0 cable can be used with 3.0 ports or hubs. To sum up: USB 3.0 devices require 3.0 cables. ... USB 2.0 cables can be used with 3.0 ports but the transfer rate will fall back to 2.0. 5. Why is my USB 3.0 port not working?Update to the Latest BIOS, or Check USB 3.0 is Enabled in BIOS. In many cases, your motherboard will be responsible for software issues related to your USB 3.0 ports or any other ports on the motherboard. For this reason, updating to the latest BIOS may fix things.

This article is a collection of 5 frequently asked questions about blower motor resistor. Catalog I. What is a Blower Motor Resistor? II. How Does the Blower Motor Resistor Work? III. How Do I Know If My Blower Motor Resistor is Bad or Broke? IV. How to Test a Blower Motor Resistor? V. Can I Fix the Blower Motor Resistor by Myself? FAQ I. What is a Blower Motor Resistor? The blower motor resistor is the blower motor component that regulates the speed. When you raise the thermostat on the air conditioner, the resistor sends a signal to the blower motor to speed up and blow more air. When you turn it down, the opposite happens. It is an electronic component that sends electronic pulses corresponding to the information you send through the adjustment dial. The electrical signal increases or decreases, which affects the overall motor speed of the fan. As far as electrical systems are concerned, they are simple, but as you might see, if something interrupts the flow of power, problems can occur.   Behind these vents in the dashboard, there is a blower motor that starts when you need heating or air conditioning. Usually, it is located in the dashboard on the other side of the steering wheel. You can't see it because it is inside the vehicle, but there it is.   A digital speed controller controls a variable speed motor. The controller typically receives a digital input from the speed switch or HVAC control head. The control head then sends a command to the motor controller to adjust the speed to the driver's requirements.   The motor controller rapidly pulses the ground circuit on and off to achieve the desired speed. So a half-speed driver request will result in the blower motor controller pulsing the ground connection off twice as often as when the fan is running at full speed.   The blower motor resistor or control module is often positioned within one of the ducts in the HVAC system, close to the blower motor, in most modern vehicles. This is done so that the resistor or control module can be cooled by passing air. A blower motor resistor was fitted on the firewall of some older vehicles, with access from under the hood.  II. How Does the Blower Motor Resistor Work? This video will give a detailed explanation of blower motor circuit to help you better understand how eactly it works. III. How Do I Know If My Blower Motor Resistor is Bad or Broke? There are a few indications that your car's blower motor resistor has failed. Because the symptoms may overlap with difficulties in other systems in your vehicle, you may require the assistance of a specialist to help you diagnose them. These are some of the most typical warning signs. (1)  No air. As simple as it may sound, one of the most noticeable indicators to look for is a lack of air moving through the vents when trying to get the heater or air conditioner to function. If nothing comes out when you turn the knob or press the button and it's intended to start blowing air, it's a good clue that the blower motor resistor has failed. This can be a sign of a variety of different issues, so don't take it as a given if this is the only signal you're receiving.   (2)  High speeds only. As previously stated, a blower motor resistor is not required in two situations. When the fan is totally turned off or when it is running at high power. Because the current does not need to be modulated at high power, it bypasses the resistance. So, if you discover that your heat and air conditioning can only switch from being completely off to being on at high power, it's almost certain that you have a broken blower motor resistor.   (3)  Low speeds only. When your fan only works at low speed, this may be a signal of poor blower motor resistance as well. However, when there is a wiring problem between the blower motor resistor and the blower motor itself, it may only work at low speeds.   (4)  The fan will not turn off. If you can't turn off the fan no matter what you do, and no matter how you try to go up, down, or turn off the fan, the fan is constantly running, which means that the blower motor resistor cannot properly regulate the current.   (5)  The blower motor works under certain settings, but does not work under other settings. The blower motor should have a series of settings, from low to high, which can be set in a variety of intermediate ranges. If you find that some of these intermediate settings are working and some of them do nothing at all, it probably means that there is a problem with the switch, and how the switch sends a signal about your settings to the blower motor resistor blower motor.   (6)  Smoking vents. This is an unusual signal of a faulty blower motor resistor, though it is not unheard of. If there is a short around the blower motor resistor and wires begin to melt, the fan may spew smoke from those melting wires back into your car's cabin.   A solid rule of thumb is that if smoke starts flowing in via your car's vents, you should pull over immediately and figure out what's wrong. If it isn't the blower motor resistor, it could be something more serious, and you should get it checked out as soon as possible.   (7)  Burning Smell. Similarly to the smoking vent issue, it is not always as dangerous as actual smoke billowing into the car's cabin, but you will detect the distinct burning smell that indicates that some metal or plastic is overheated somewhere in the vehicle. This is frequently associated with one of the other signals we've already mentioned above. IV. How to Test a Blower Motor Resistor? Blower motor resistor test V. Can I Fix the Blower Motor Resistor by Myself? Whether you can repair the blower motor resistor yourself obviously depends on how much you know about blower motor resistors and general car maintenance. If you are reading a guide on blower motor resistance and its functions, you may not be familiar with them. Therefore, we recommend that you do not try to fix this problem yourself, as this is not a beginner-level fix.   This is not to say that you cannot replace the blower motor resistance yourself, but it will be a complicated task. But we provide you with some basic methods to diagnose and repair some simple blower motor problems, for reference only. For specific steps, please consult professionals or check related videos on youtube.   (1) The blower only works in high speed. This is a sure sign of a bad blower motor resistor, not a faulty speed switch. Change the resistor.   (2) The blower only works in low speed. Check for a blown fuse or a faulty high-speed relay. Replace the high-speed relay with a relay of the same part number. Check the fuse for the high speed relay's control side as well. Verify that the high speed relay's ground side is good.   (3) Repeated failures of the blower motor resistor Check for full airflow at the vents. If airflow appears to be restricted or lower than typical, a blocked cabin air filter is to blame. Examine the cabin air filter. If everything is ok, look for debris on the evaporator or heater. When the airflow is reduced, the blower motor resistor overheats and fails. Reduced airflow forces the blower motor to work harder and draw more current, which might result in repeated blower motor resistor failures. FAQ 1. What does a resistor do on a blower motor? Blower resistors are resistors which are used to control the fan speed of automotive blowers. The fan speed can be changed either by switching the blower resistor resistance mechanically, using a rotating lever, or electronically by the air conditioning system. 2. Can I bypass blower resistor? Blower resistors are resistors which are used to control the fan speed of automotive blowers. The fan speed can be changed either by switching the blower resistor resistance mechanically, using a rotating lever, or electronically by the air conditioning system. 3. What can cause a blower motor to stop working? In a situation where the motor doesn't work on any speed, the most likely causes are: a blown power supply fuse, a bad motor ground connection, bad motor speed control module or a failed motor. On all systems, a failed blower motor is least likely. ... Start by checking the blower fuse and HVAC controller fuse. 4. How do you test a blower motor resistor with a multimeter? Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications. 5. Is the blower motor resistor supposed to get hot? Yes that resistor will get very hot. Most people don`t know this but it is faster to defrost the windshield on low or medium fan speed due to that resistor putting off heat. Also that resistor needs to be cooled off with the air flow or it will burn up . 6. What is the function of a blower motor resistor? A blower motor resistor is an adjustable resistor. This electrical component is used to control the air conditioning system of a vehicle. It is the part that controls the fan speed of the fan motor according to settings that can be changed by turning the knob to the left or right, thereby increasing or decreasing the resistance of the electric current flowing to the rotating fan motor connected to the fan. 7. Where is the blower motor resister? A blower motor resistor, typically located beneath the passenger side dashboard, contains three resistors, or sets of terminals designed to generate voltage in proportion to electrical current. 8. How do you replace a blower motor resistor? Safety Tip: Always wear safety glasses when working on your motor. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or closed toe shoes. 1.Remove the negative battery terminal.2.Locate the blower motor resistor on the passenger side under the dash board. It is mounted to the the blower housing near the blower motor.3.Disconnect the electrical connector to the blower motor resistor.4.Remove the screws or bolts to the blower motor resistor and remove the resistor.5.Installation is the reverse of the removal. 9. Can you test a blower motor resistor? Yes. Set your multimeter to Diod or continuity and place leads on either side of the resistor. If no tone and infinite resistance it is bad. If tone but no resistance it is bad. If you have continuity to ground, something has shorted to ground look for heat damage. If you have tone and resistance it is good.  10. Why does a blower motor resistor keep going out? If you are constantly blowing that part. You ether have the motor pulling to much amps. If it is home unit it could also be a inline control board cap.

IntroductionAs everyone knows, Error correction code memory (ECC memory) is a type of computer data storage technique. It identifies and fixes the most common errors which could otherwise lead to data corruption or system crashes. In other words, it is one of the most important techs for this loss and system errors prevention. There will be people who have such a question: now the memory technology is improved greatly, it’s possible to use ECC server RAM inside of your regular desktop computer at home, but is it something you SHOULD do? This note will help you find clues step by step.ECC Memory ExplainedCatalogIntroductionⅠ What Causes Errors in RAM?Ⅱ Is ECC RAM Better?Ⅲ ECC Server RAM or Regular Home Desktop?Ⅰ What Causes Errors in RAM?The ram error is caused by electromagnetic interference inside the computer. This interference will cause the units of DRAM (Dynamic Random Access Memory) to spontaneously change to the opposite state. Unit errors may be hidden, that is, they will not have a serious impact on the data. However, the memory units are interrelated, so unit changes may affect the entire operating system, resulting in system errors, especially when the strict operation is required. To be specific, memory errors will cause security vulnerabilities, crashes, transcription errors, lost transactions and corrupted or lost data, and one of the most common types of memory error is a single-bit error.Ⅱ Is ECC RAM Better?In the face of these problems, if memory can fix the error itself, what will it look like? That is ECC RAM.Memory Chips DifferenceECC RAM is server memory. This type of memory module has an ECC error check storage chip (the number of storage chips is an odd number). The application of ECC can ensure that the server is safer and more stable during operation. However, the number of chips stored in ordinary memory sticks is even. In reality, ECC RAM has 9 memory chips instead of 8. Error Checking and CorrectingThe ECC memory is equipped with ECC error-checking technology. After error checking and correction, the stability and reliability of the server system can be effectively guaranteed. For ordinary ram, when the word detects an error, the error location cannot be determined, and the error cannot be corrected. Therefore, for a single task that takes a long time and cannot be suspended or error, ECC memory is an inevitable choice. However, ordinary PCs will not use because of high-cost price. Application DifferenceBecause ECC memory can effectively store and maintain data integrity and is equipped with check and correction technology, ECC memory further reduces data corruption. Therefore, it is mostly used in servers and graphics workstations such in financial and scientific industries. Non-ECC memory sticks are more suitable for the general public's use. Capacitor DifferenceAs server memory applications require higher capacity, ECC memory modules usually start at 4GB, while ordinary memory modules usually start at 2GB. The standard configuration on home computers is 4~8GB of memory. Price DifferenceDue to the higher-tech of ECC memory sticks, their capacity is also larger than ordinary memory. Therefore, ECC memory sticks are more expensive than ordinary memory.Ⅲ ECC Server RAM or Regular Home Desktop?ECC memory is usually used in servers or graphics workstations. Because of the check and correction function, when there are some read and write errors in the memory, the ECC RAM can correct these errors and reduce the probability of downtime/blue screen. Guaranteed data storage and accuracy of reading and writing.Server memory and ordinary PC memory are very similar, there is no obvious difference in appearance and structure, but its price is higher than ordinary memory. There are three main types of server memory: SDRAM, DDR, and DDR2. At present, server memory is mostly used by DDR and DDR2. As time goes by, the server uses some new technologies now, such as ECC, chip kill, register, hot-swap technology, FB-DIMM (full buffer memory module), etc. More server memory currently adopts ECC and REG ECC technologies. The chips on REG ECC memory are generally 2-3 more than ordinary motherboards, mainly PLL (phase-locked loop) and Register IC. ECC and ECC REG memory have been developed for a period, and the frequency mainly has 133, 266, 333, 400, 533, and 667 stages. What is RECC? The specific uses of RECC memory are as follows: phase-locked loop chip, the bottom of the memory stick are smaller than Register ICs. Generally, there is only one, which can adjust the clock signal and ensure signal synchronization between the memory modules. The smaller IC chip (2-3 pieces) at the bottom plays a role in improving the driving capability. Server products need to support large-capacity memory. The motherboard alone cannot drive such a large-capacity memory. Instead, the memory module with Register is used to improve the driving ability, so that the server can support up to 32GB of memory. Because of the PLL and Register chips, the server memory capacitor can be made very large, it can better meet the endless requirements of the ever-increasing software for memory. Therefore, it is recommended that the server whose requirement is over 16G use RECC RAM.RECC has one more register. We can understand the function of the memory as a book directory. When the memory receives a read and write command, it will retrieve this directory first, and then perform read and write operations, which will greatly improve the efficiency of the server memory. So some people mistakenly think that RECC RAM runs slower than ECC RAM. The Register memory that can be used at present also has an ECC function, and some motherboards require the memory to support Register. In fact, all registered memory is ECC memory. The use of ECC memory requires the support of other computer components, such as the motherboard and cpu, and may also need to be set in the BIOS before it can be used on most server CPUs and motherboards (some non-server CPUs and motherboards also support). In addition, when purchasing ecc memory, you need to pay attention to whether it is ecc udimm or ecc rdimm or ecc lrdimm or ecc 3ds rdimm or something else. Because your computer configuration may not support some types.What’s more, all of the modern, contemporary storage drives use ECC at some level internally. HDD, SSDs. The data densities of the HDD push the edge where need to keep up with track integrity. NAND in SSDs tend to loose data bits in usage over time. The SSD controller in the T2 isn't remarkable on the ECC dimension. All the ones that store the data encrypted 'at rest' basically have to if going to be competently implemented. In addition, ECC generally works on all Ryzen Chips minus the APUs (with the exception of the pro apus), they tend to not be on the QVL since it costs time and money to do that. Frequently Asked Questions about ECC Server Memory1. What is ECC memory?Error correction codeError correction code (ECC) memory is a type of RAM memory found in workstations and servers. It's valued by professionals and businesses with critical data for its ability to automatically detect and correct memory errors, thus fighting data corruption. 2. Which is better ECC or non-ECC memory?Non-ECC (also called non-parity) modules do not have this error-detecting feature. ... Using ECC decreases your computer's performance by about 2 percent. Current technology DRAM is very stable, and memory errors are rare, so unless you have a need for ECC, you are better served with non-parity (non-ECC) memory. 3. How does ECC memory work?ECC memory uses the extra bits to store an encrypted code when writing data to memory, and the ECC code is stored at the same time. ... As data is processed, ECC memory is constantly scanning code with a special algorithm to detect and correct single-bit memory errors. 4. What is the benefit of ECC memory?ECC memory protects your system from potential crashes and inadvertent changes in data by automatically correcting data errors. This is achieved with the addition of a ninth computer chip on the RAM board, which acts as an error check and correction for the other eight chips. 5. Who needs ECC RAM?Error-correcting code memory (ECC memory) is a type of computer data storage that can detect and correct the most common kinds of internal data corruption. ECC memory is used in most computers where data corruption cannot be tolerated under any circumstances, such as for scientific or financial computing.