The Kynix Components

CatalogDescriptionCAD ModelsPin ConfigurationBlock DiagramFeaturesApplicationsDatasheetSpecificationsManufacturerUsing WarningFAQDescriptionThe TPS92692 and TPS92692-Q1 are high accuracy peak current mode based controllers designed to support step-up/down LED driver topologies. The device incorporates a rail-to-rail current amplifier to measure LED current and spread spectrum frequency modulation technique for improved EMI performance. This high performance LED controller can independently modulate LED current using either analog or PWM dimming techniques. Linear analog dimming response with over 15:1 range is obtained by varying the voltage across the high impedance analog adjust (IADJ) input. PWM dimming of LED current is achieved by directly modulating the DIM/PWM input pin with the desired duty cycle or by enabling the internal PWM generator circuit. The PWM generator translates the DC voltage at DIM/PWM pin to corresponding duty cycle by comparing it to the internal triangle wave generator.The optional PDRV gate driver output can be used to drive an external P-Channel series MOSFET. The TPS92692 and TPS92692-Q1 devices support continuous LED status check through the current monitor (IMON) output. The devices also include an open drain fault indicator output to indicate LED overcurrent, output overvoltage and output undervoltage conditions. CAD Models Figure: PCB Symbol  Figure: Footprint  Figure: 3D Model Pin Configuration Figure: Pin Configuration Block Diagram Figure: Block Diagram FeaturesWide Input Voltage: 4.5 V to 65 V • Better than ± 4% LED Current Accuracy over–40°C to 150°C Junction Temperature RangeSpread Spectrum Frequency Modulation forImproved EMIComprehensive Fault Protection Circuitry withCurrent Monitor output and Open Drain Fault FlagIndicatorInternal Analog Voltage to PWM Duty CycleGenerator for stand-alone Dimming OperationCompatible with Direct PWM Input with over1000:1 Dimming RangeAnalog LED Current Adjust Input (IADJ) with over15:1 Contrast RatioIntegrated P-Channel Driver to enable Series FETDimming and LED ProtectionTPS92692-Q1: Automotive Q100 Grade 1Qualified ApplicationsTPS92692-Q1: Automotive Exterior Lighting ApplicationsDriver Monitoring Systems (DMS)LED General Lighting ApplicationsExit Signs and Emergency Lighting DatasheetYou can download the datasheet from the link given below.TPS92692QPWPRQ1-Datasheet SpecificationsProduct AttributeAttribute ValueManufacturer:Texas InstrumentsProduct Category:LED Lighting DriversNumber of Channels:1 ChannelOutput Current:5 AInput Voltage:4.5 V to 65 VOperating Frequency:800 kHzSupply Current - Max:6.6 mAMinimum Operating Temperature:- 40 CMaximum Operating Temperature:+ 125 CMounting Style:SMD/SMTPackage / Case:HTSSOP-20Qualification:AEC-Q100Series:TPS92692-Q1Packaging:ReelPackaging:Cut TapePackaging:MouseReelBrand:Texas InstrumentsMoisture Sensitive:YesOperating Temperature Range:- 40 C to + 125 CProduct:LED DriversProduct Type:LED Lighting DriversFactory Pack Quantity:2000Subcategory:Driver ICsTopology:Boost, Buck, Buck-Boost, Cuk, Flyback, SepicType:LED ControllerWidth:4.5 mmUnit Weight:0.004522 oz ManufacturerTexas Instruments Incorporated (TI) is an American technology company headquartered in Dallas, Texas, that designs and manufactures semiconductors and various integrated circuits, which it sells to electronics designers and manufacturers globally. It is one of the top 10 semiconductor companies worldwide based on sales volume.The company's focus is on developing analog chips and embedded processors, which account for more than 80% of its revenue.TI also produces TI digital light processing technology and education technology products including calculators, microcontrollers and multi-core processors. Using WarningNote: Please check their parameters and pin configuration before replacing them in your circuit. FAQWhat does the LED controller do?The controller will control the driver circuit according to the program input in advance,so that LED lights can be normal and change regularly as we think. The LED controller can adjust the RGB tricolor intelligent light,and also can be used for remote dimming. Does any controller work for LED lights?RGB LED light strips can be controlled using different kinds of controllers. There is a wide variety of LED controllers available in the market from single-zone RF controllers to DMX controllers that can handle up to 500 zones at the same time. Can I use any LED remote for LED lights?Answer: Yes, One remote can control multiple receivers, you need to match code with each receiver firstly,following the steps: . Correct connection led strip light, make work normal. ... Correct connection led strip light, make work normal. 

Catalog Product Overview TPS5430DDAR Related Video Introduction TPS5430DDAR CAD Models TPS5430DDAR Pin Configuration TPS5430DDAR Block Diagram TPS5430DDAR Schematic TPS5430DDAR Features TPS5430DDAR Applications TPS5430DDAR Datasheet TPS5430DDAR Specifications TPS5430DDAR Manufacturer Using Warning TPS5430DDAR FAQ   Product Overview The TPS543x is a high-output-current PWM converter that integrates a low-resistance, high-side N-channel MOSFET. Included on the substrate with the listed features are a high-performance voltage error amplifier that provides tight voltage regulation accuracy under transient conditions; an undervoltagelockout circuit to prevent start-up until the input voltage reaches 5.5 V; an internally set slow-start circuit to limit inrush currents; and a voltage feedforward circuit to improve the transient response. Using the ENA pin, shutdown supply current is reduced to 18 μA typically. Other features include an active-high enable, overcurrent limiting, over-voltage protection and thermal shutdown. To reduce design complexity and external component count, the TPS543x feedback loop is internally compensated. The TPS5431 is intended to operate from power rails up to 23 V. The TPS5430 regulates a wide variety of power sources including 24 V bus.   The TPS543x device is available in a thermally enhanced, easy to use 8-pin SOIC PowerPAD™ package. TI provides evaluation modules and the Designer software tool to aid in quickly achieving high-performance power supply designs to meet aggressive equipment development cycles.   TPS5430DDAR Related Video Introduction Video Description: Get TPS5430DDAR Price and Buy TPS5430DDAR from RANTLE. Contact us at [email protected] for your TPS5430DDAR requirement Now. Rantle East Electronic - Reliable TPS5430DDAR Supplier and TPS5430DDAR Distributor in China.   TPS5430DDAR CAD Models Figure: TPS5430DDAR PCB Symbol       Figure: TPS5430DDAR Footprint       Figure: TPS5430DDAR 3D Models   TPS5430DDAR Pin Configuration Figure: TPS5430DDAR Pin Configuration   TPS5430DDAR Block Diagram Figure: TPS5430DDAR Block Diagram   TPS5430DDAR Schematic Figure: TPS5430DDAR Schematic   TPS5430DDAR Features Wide Input Voltage Range: – TPS5430: 5.5 V to 36 V – TPS5431: 5.5 V to 23 V Up to 3-A Continuous (4-A Peak) Output CurrentHigh Efficiency up to 95% Enabled by 110-mΩIntegrated MOSFET SwitchWide Output Voltage Range: Adjustable Down to1.22 V with 1.5% Initial AccuracyInternal Compensation Minimizes External PartsCountFixed 500 kHz Switching Frequency for SmallFilter SizeImproved Line Regulation and TransientResponse by Input Voltage Feed ForwardSystem Protected by Overcurrent Limiting,Overvoltage Protection and Thermal Shutdown–40°C to 125°C Operating Junction TemperatureRangeAvailable in Small Thermally Enhanced 8-Pin SOPowerPAD™ PackageCreate a Custom Design Using the TPS5430 WiththeWEBENCH® Power Designer   TPS5430DDAR Applications Consumer: Set-top Box, DVD, LCD DisplaysIndustrial and Car Audio Power SuppliesBattery Chargers, High Power LED Supply12-V/24-V Distributed Power Systems   TPS5430DDAR Datasheet You can download the datasheet from the link given below: TPS5430DDAR Datasheet   TPS5430DDAR Specifications TypeDescriptionCategoryIntegrated Circuits (ICs)PMIC - Voltage Regulators - DC DC Switching RegulatorsMfrTexas InstrumentsSeries-Part StatusActiveFunctionStep-DownOutput ConfigurationPositiveTopologyBuckOutput TypeAdjustableNumber of Outputs1Voltage - Input (Min)5.5VVoltage - Input (Max)36VVoltage - Output (Min/Fixed)1.221VVoltage - Output (Max)32.04VCurrent - Output3AFrequency - Switching500kHzSynchronous RectifierNoOperating Temperature-40°C ~ 125°C (TJ)Mounting TypeSurface MountPackage / Case8-PowerSOIC (0.154", 3.90mm Width)Supplier Device Package8-SO PowerPadBase Product NumberTPS5430   TPS5430DDAR Manufacturer Texas Instruments Incorporated (TI) is an American technology company headquartered in Dallas, Texas, that designs and manufactures semiconductors and various integrated circuits, which it sells to electronics designers and manufacturers globally. It is one of the top 10 semiconductor companies worldwide based on sales volume.The company's focus is on developing analog chips and embedded processors, which account for more than 80% of its revenue.TI also produces TI digital light processing technology and education technology products including calculators, microcontrollers and multi-core processors. The company holds 45,000 patents worldwide as of 2016.   Using Warning Note: Please check their parameters and pin configuration before replacing them in your circuit.   TPS5430DDAR FAQ What does a step-down converter do? A buck converter (step-down converter) is a DC-to-DC power converter which steps down voltage (while drawing less average current) from its input (supply) to its output (load).   How does a step up converter work? The boost converter is used to "step-up" an input voltage to some higher level, required by a load. This unique capability is achieved by storing energy in an inductor and releasing it to the load at a higher voltage.   Which is more efficient step up or step down transformer? Any differences in the efficiencies of step-up versus step-down conversion are apt to be minor compared with issues resulting from series or parallel battery connections. Step up and step down idealized converters are exactly the same thing.   What is difference between step down transformer and step up transformer? A transformer that increases the voltage from primary to secondary (more secondary winding turns than primary winding turns) is called a step-up transformer. Conversely, a transformer designed to do just the opposite is called a step-down transformer.   Where do we use step up and step down transformers? Step-up/down transformers are used to produce the voltage as well as reduce energy loss during the power transmission stage. Step-up transformers are used in central power stations. They allow the stations to increase the voltage to the necessary level to produce electricity.  

74LS74 is a Dual D Flip-Flop.The IC 74LS74 is a type of dual D-type positive edge triggered flip flop, with preset, clear, and complementary outputs. It features a large operating voltage range, wide operating conditions, and outputs directly interfaced to CMOS, NMOS, and TTL. The LOW logic level of the preset or clear inputs will set or reset outputs regardless of the logical level of the other inputs.This blog provides you with a basic overview of the 74LS74 Flip-Flop, including its pin descriptions, functions and specifications, alternative products, etc., to help you quickly understand what 74LS74 is.We will be glad to find that this blog can be useful for people loving electronic components :)Still do not have idea about D-type Flip-Flop? Watch this! Catalog74LS74 Flip-Flop Pinout74LS74 Flip-Flop Feature74LS74 Flip-Flop EquivalentsHow to use 74LS7474LS74 Flip-Flop Applications74LS74 Flip-Flop PackageComponent Datasheet74LS74 Flip-Flop PinoutPin NumberPin SymbolNameDescription5,91Q / 2QOutputOutput Pin of the Flip Flop6,81Q’(bar) / 2Q’(bar)Complementary OutputInverted output pin of Flip Flop3, 111CLK / 2CLKClock Input PinThese pins must be provided with clock pulse for the flip flop1,131CLR (bar) / 2CLR (bar)Clear DataResets the flip flop by clearing its memory2,121D /2DData Input PinInput pin of the Flip Flop4, 101PRE (bar) / 2PRE (bar)PRE InputAnother Input pin for Flip Flop. Also referred to as a set pin7VssGroundConnected to the ground of the system14Vdd/VccSupply VoltagePowers the IC typically with 5V74LS74 Flip-Flop FeatureDual D Flip Flop Package ICOperating Voltage: 2V to 15VPropagation Delay: 40nSMinimum High-Level Input Voltage: 2 VMaximum Low-Level Input Voltage: 0.8VOperating Temperature: 0 to 70°CHigh-Level Output Current: 8mAAvailable in 14-pin SO-14, SOT42 packagesNote: You can find complete technical details in the 74LS74 data sheet at the end of this page.74LS74 Flip-Flop Equivalents74LVC2G80, HEF40312BHow to use 74LS74Using a Flip-Flop is pretty straight ahead. Just use the Vcc and GND pin to power the IC. As stated earlier, each flip-flop operates independently, just connect the input signals 2 and 3 to the 1st flip-flop and you'll get the output at pins 5 and 6. The pin 3 should be provided with a clock source that normally uses a PWM signal from the MCU or 555 timers. You can use the pin to clear the data and reset the flip flop by making it high. The complete operation of the Flip Flop can be understood by taking a look at the function table below. The symbol "X" indicates that you don't care, and the up-arrow indicates the rising edge of the signal.INPUTSOUTPUTSPRE (bar)CLR (bar)CLKDQQ (bar)LHXXHLHLXXLHLLXXHHHH HHLHH LLHHHLXQ0Q0 (bar)You can also simulate an IC to check that it works as you wish. Here I used logic status and logic bits to see if the IC works as it should, but you can replace them with the actual circuitry of your application to check if it fits your needs. The gif file shown below can be checked with the above truth table to make sure the IC works as desired.74LS74 Flip-Flop ApplicationsUsed as Shift RegistersMemory/Control RegistersBuffer CircuitsSampling CircuitsLatching devices74LS74 Flip-Flop PackageThe dimensions for IC 74LS74 are given below. The dimensions are for the CDIP package. If you are using a different IC package, please refer to the 74LS74 data sheet.That’s all for our introduction to 74LS74. If you find this blog useful, please bookmark our website Apogeeweb, we will provide you with electronic component blogs, industry news, tools, etc. that you are interested in. Stay tuned for our next blog…Component Datasheet74LS74 DatasheetFAQWhat is the purpose of a 74LS74?74LS74A flip-flop IC utilizes the Schottky TTL circuitry to produce high-speed D-type flip-flops. Each flip-flop has individual clear and set inputs, and also complementary Q and Q`(bar) outputs. What is dynamic flip-flop?Dynamic flip-flop (FF) conversion is a method of time borrowing (TB) for improving the performance of digital systems prone to variations. This method was compared with soft edge FF and dynamic clock stretching through simulations on different ITC'99 benchmarks. What is toggle flip-flop?Toggle Flip-flops are sequential logic circuits frequently used as single bit bistable storage elements in counters, memory divices or as frequency dividers in response to a clock pulse. The Toggle Flip-flop is another type of bistable sequential logic circuit based around the previous clocked JK flip-flop circuit.

DescriptionThe 74HC595 is a high-speed CMOS 8-BIT SHIFT REGISTERS/OUTPUT LATCHES (3-STATE) fabricated with silicon gate C2MOS technology. This device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. The storage register has 8 3-STATE outputs. Separate clocks are provided for both the shift register and the storage register.  The shift register has direct-overriding clear, serial input, and serial output (standard) pins for cascading. Both the shift register and storage register use positive-edge triggered clocks. If both clocks are connected together, the shift register state will always be one clock pulse ahead of the storage register.  All inputs are equipped with protection circuits against static discharge and transient excess voltage.The Shift Register: Explained [74HC595]CatalogDescriptionFeaturesApplicationPinoutLogic DiagramParametersComponent DatasheetPackageProduct ManufacturerFAQOrdering & QuantityFeaturesLow quiescent current: 80μA maximumLow input current: 1μA maximum8-bit serial-in, parallel-out shift register  with storageWide operating voltage range: 2V～6VShift register has direct clearGuaranteed shift frequency: DC to 30 MHzPackage: SOP16ApplicationSerial-to-parallel data conversionRemote control holding registerPinoutPin No.SymbolName and Function1,2,3,4,5,6,7,15QA to QHData output8GNDGround (0V)9QHSerial data output10SCLRShift register clear input11SCKShift register clock input12RCKStorage register clock input13GOutput enable input14SISerial data input16VCCPositive supply voltageLogic DiagramParametersBrand NameDiodesLow-power consumptionWhen TA =25℃, Icc=4μA(MAX)Low quiescent currentMaximum 80 μALow input currentMaximum 1 μAWide operating voltage range2V-6VPackageDIP16/SOP16Component DatasheetDatasheet74HC595 DatasheetPackage　　Product ManufacturerDiodes Incorporated is a leading global manufacturer and supplier of high-quality application specific standard products within the broad discrete, logic, analog, and mixed-signal semiconductor markets. Diodes’ corporate headquarters and Americas’ sales office are located in Plano, Texas, and Milpitas, California. Diodes serve the consumer electronics, computing, communications, industrial, and automotive markets. Diodes’ products include diodes, rectifiers, transistors, MOSFETs, protection devices, function-specific arrays, single gate logic, amplifiers and comparators, Hall-effect and temperature sensors, power management devices, including LED drivers, AC-DC converters and controllers, DC-DC switching and linear voltage regulators, and voltage references along with special function devices, such as USB power switches, load switches, voltage supervisors, and motor controllers.FAQWhat is 74HC595?74HC595 is a shift register which works on Serial IN Parallel OUT protocol. It receives data serially from the microcontroller and then sends out this data through parallel pins. We can increase our output pins by 8 using the single chip.What is a 74hc595n?8-bit Shift Register 74HC595NA shift register is a chip you can use to control many outputs (8 here) at the same time while only using a few pins (3 here) of your Arduino.How does a shift register work?Shift registers hold the data in their memory which is moved or “shifted” to their required positions on each clock pulse. Each clock pulse shifts the contents of the register one bit position to either the left or the right.How 74HC595 Shift Regiester works?The 595 has two registers (which can be thought of as “memory containers”), each with just 8 bits of data. The first one is called the Shift Register. The Shift Register lies deep within the IC circuits, quietly accepting input.How does an 8 bit shift register work?The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be added to a microcontroller by converting data between parallel and serial formats. Your chosen microprocessor is able to communicate with the The SN74HC595N using serial information then gathers or outputs information in a parallel (multi-pin) format. Essentially it takes 8 bits from the serial input and then outputs them to 8 pins. 

The STM32F103RCT6 is a high density performance line, ARM Cortex-M3 32bit microcontroller in 64 pin LQFP package.CatalogProduct OverviewCAD ModelsProduct PinoutSTM32F103RCT6 FeaturesSTM32F103RCT6 BenefitsSTM32F103RCT6 Product AttributesSTM32F103RCT6 ApplicationsSimilar PartsUsing WarningsFAQProduct OverviewThe STM32F103RCT6 is a high density performance line, ARM Cortex-M3 32bit microcontroller in 64 pin LQFP package. It incorporates high performance RISC core with 72MHz operating frequency, high speed embedded memories, extensive range of enhanced I/Os and peripherals connected to two APB buses. The STM32F103RCT6 features 12bit ADC, timers, PWM timer, standard and advanced communication interfaces. A comprehensive set of power saving mode allows design of low power applications.CAD ModelsSTM32F103RCT6 Symbol STM32F103RCT6 Footprint STM32F103RCT6 3D ModelProduct PinoutLQFP144 Pinout LQFP100 Pinout LQFP64 PinoutSTM32F103RCT6 Features• Operating voltage range from 2V to 3.6V• 256Kbytes of flash memory• 48Kbytes of SRAM• CRC calculation unit, 96bit unique ID• Three 12bit, 1µs A/D converter (up to 16 channels) and two 12bit DAC 92 channel• Four general purpose, two advanced control and two basic timers• 51 fast I/O ports• Serial wire debug (SWD) and JTAG interfaces• Three SPI, two I2C, five USART, one USB, one SDIO and one CAN interfaces• Ambient operating temperature range from -40°C to 85°CSTM32F103RCT6 Benefits• Excellent real-time behaviour• Oustanding power efficiency• Superior and innovative peripherals• Maximum integration• Cross family pin-to-pin, peripheral and software compatibilitySTM32F103RCT6 Product AttributesCase/PackageLQFPNumber of Pins64Ambient Temperature Range High85 °CCore ArchitectureARMData Bus Width32 bDensity2 MbFlash Memory Size256 kBFrequency72 MHzInterfaceCAN, I2C, I2S, IrDA, LIN, SPI, USART, USBMax Frequency72 MHzMax Junction Temperature (Tj)125 °CMax Operating Temperature85 °CMax Power Dissipation444 mWMax Supply Voltage3.6 VMemory Size256 kBMemory TypeFLASHMin Operating Temperature-40 °CMin Supply Voltage2 VNominal Supply Current1.9 µANumber of A/D Converters3Number of ADC Channels16Number of Bits32Number of D/A Converters2Number of I2C Channels2Number of I/Os51Number of Programmable I/O51Number of PWM Channels16Number of SPI Channels3Number of Timers/Counters8Number of UART Channels2Number of USART Channels3Number of USB Channels1Oscillator TypeInternalPeripheralsDMA, I2C, POR, PWM, Temp Sensor, WDTRAM Size48 kBSchedule B8542310000TerminationSMD/SMTWatchdog TimerYesHeight1.45 mmLength10 mmWidth10.2 mmLead FreeLead FreeRadiation HardeningNoREACH SVHCNo SVHCRoHSCompliantSTM32F103RCT6 Applications• Embedded Design & Development• Motor Drive & Control• Medical, Industrial• Portable Devices• Wireless, Imaging, Video & Vision, • Consumer Electronics, AutomotiveSimilar PartsSTM32F107RCT6, STM32F105RCT6, STM32F105RCT7, MK20D256VLH7Using WarningsMarket demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.FAQWhat package does the STM32F103RCT6 come with?64 pin LQFP What is the temperature range of STM32F103RCT6?–40 to +105 °C What is the power supply of STM32F103RCT6?From 2.0 to 3.6 V.

MB10F is a Surface Mount Glass Passivated Bridge Rectifier 0.5A 1000V 4-SOIC.CatalogProduct OverviewMB10F CAD ModelsMB10F Package DimensionsMB10F Suggested Pad LayoutMB10F FeaturesMB10F Product AttributesMB10F ApplicationsMB10F Purchasing RiskUsing WarningsComponent DatasheetMCP602 ManufacturerProduct OverviewAs an ultra-thin SMD bridge rectifier, MB10F converts alternating current into direct current, based on the single-phase conductivity of the diode. Designed for smaller devices, and low energy-consuming application circuits, which is an ideal choice for the design of trendy electronic products. The soldering pins are the same as those of the MB6S, which can be directly replaced without changing the PCB board. So it is of great help to the development of the production industry of miniaturized high-current products, and is very suitable for portable applications that save circuit board space design.The Passivated Bridge Rectifier is ideal for automated placement and features reliable low-cost construction using a precise plastic moulding technique. In power supplies, bridge rectifiers are used to provide necessary DC voltages for electronic components or devices.MB10F CAD ModelsMB10F CAD ModelsMB10F Package DimensionsPackage DimensionsMB10F Suggested Pad LayoutMB10F Suggested Pad LayoutMB10F Features• Plastic material has U/L flammability classification 94V-O• High surge overload rating : 35A peak• Saves space on printed circuit boards• High temperature soldering guaranteed : 260° C/10sec/ at 5 lbs. (2.3kg) tension• Terminals: Plated leads solderable per MIL-STD-750, Method 2026• Case: Molded plastic body over passivated junctions• Polarity: Polarity symbols marked on body Dimensions in inches and (millimeters)• Mounting Position : Any• Weight : 0.0078 ounce, 0.22 gram• Package : MBS• Case Material: Molded Plastic. UL Flammability Classification Rating 94V-0• Moisture Sensitivity: Level 1 per J-STD-020• Terminals: Lead Free Plating (Matte Tin Finish). Solderable per MIL-STD-202, Method 208• Polarity: As Marked on Body• Weight: 0.08 grams (Approximate)MB10F Product AttributesSpecificationsValuesManufacturer:Diodes IncorporatedProduct Category:Bridge RectifiersRoHS:DetailsType:Single Phase BridgeMounting Style:SMD/SMTPackage/Case:MBF-4Package Body Material:Plastic/EpoxyPackage Style:Small OutlineIf - Forward Current:800 mAPeak Reverse Voltage:1000 VVf - Forward Voltage:0.94 VMax Surge Current:30 AMinimum Operating Temperature:- 55 CMaximum Operating Temperature:+ 150 CNumber of Elements:4Number of Phases1Length:4.95 mmWidth:4.1 mmHeight:1.6 mmSeries:MB10Packaging:ReelPackaging:Cut TapePackaging:MouseReelBrand:Diodes IncorporatedIr - Reverse Current:0.2 uAProduct Type:Bridge RectifiersFactory Pack Quantity:5000Subcategory:Diodes & RectifiersVr - Reverse Voltage:1000 VDiode Element Material:SiliconTerminal Form:Gull WingTerminal Position:DualMB10F ApplicationsMB10F is suitable for AC to DC bridge full wave rectification for SMPS, LED lighting, adapter, battery charger, home appliances, office equipment, and telecommunication applications.MB10F Purchasing RiskMB10F Purchasing RiskUsing WarningsPlease check their parameters and pin configuration before replacing them in your circuit.Component DatasheetMB10F PDFMCP602 ManufacturerDiodes Incorporated is a leading global manufacturer and supplier of high-quality application specific standard products within the broad discrete, logic, analog, and mixed-signal semiconductor markets. Diodes serves the consumer electronics, computing, communications, industrial, and automotive markets.FAQWhat is MB10F?MB10f is a surface Mount Glass passivated bridge rectifier with Maximum Peak reverse voltage of 1000 volts & average output current of 0.8 Ampere. What is an ideal choice for the design of trendy electronic products?Low energy-consuming application circuits What type of products is MB10F of great help to the development of?Miniaturized high-current products What is the use of MB10F?Suitable for AC to DC bridge full wave rectification for SMPS, LED lighting, adapter, battery charger, home appliances, office equipment, and telecommunication applications.