Phone

    00852-6915 1330

LSM303DLHC Sensor: Block Diagram, Calibration and Datasheet

  • Contents

 

The LSM303DLHC is a system-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor.

 

Catalog

Product Overview

Product Pinout

Block Diagram

LSM303DLHC Calibration

Features

Applications

Functionality

Datasheet

Product Attributes

Magnetic Field Digital Interface

Using Warning

FAQ

 

Product Overview

The LSM303DLHC is a system-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor. The LSM303DLHC has linear acceleration full scales of ±2g / ±4g / ±8g / ±16g and a magnetic field full scale of ±1.3 / ±1.9 / ±2.5 / ±4.0 / ±4.7 / ±5.6 / ±8.1 gauss. The LSM303DLHC includes an I2C serial bus interface that supports standard and fast mode 100 kHz and 400 kHz.

 

The system can be configured to generate interrupt signals by inertial wake-up/free-fall events as well as by the position of the device itself. Thresholds and timing of interrupt generators are programmable by the end user. Magnetic and accelerometer blocks can be enabled or put into power-down mode separately. The LSM303DLHC is available in a plastic land grid array package (LGA) and is guaranteed to operate over an extended temperature range from -40 °C to +85 °C.

 

Product Pinout

Figure-LSM303DLHC-Pinout

 

LSM303DLHC-Pinout

 

Block Diagram

Figure-LSM303DLHC-Block-Diagram

 

LSM303DLHC-Block-Diagram

 

LSM303DLHC Calibration

The factory calibration of the LSM303 is accurate enough for most purposes.

Figure-LSM303DLHC-Calibration

 

LSM303DLHC-Calibration

Features

  • 3 magnetic field channels and 3 acceleration channels 
  • From ±1.3 to ±8.1 gauss magnetic field full scale 
  • ±2g/±4g/±8g/±16g linear acceleration full scale 
  • 16-bit data output 
  • I²C serial interface 
  • Analog supply voltage 2.16 V to 3.6 V 
  • Power-down mode / low-power mode 
  • 2 independent programmable interrupt generators for free-fall and motion detection 
  • Embedded temperature sensor 
  • Embedded FIFO 
  • 6D/4D-orientation detection 
  • ECOPACK® RoHS and “Green” compliant

 

Applications

  • Tilt-compensated compasses 
  • Map rotation 
  • Position detection 
  • Motion-activated functions 
  • Free-fall detection 
  • Click/double-click recognition 
  • Pedometers 
  • Intelligent power-saving for handheld devices
  • Display orientation 
  • Gaming and virtual reality input devices 
  • Impact recognition and logging 
  • Vibration monitoring and compensation

Figure-LSM303DLHC-Application-Hints

 

LSM303DLHC-Application-Hints

 

Functionality

The LSM303DLHC is a system-in-package featuring a 3D digital linear acceleration and 3D digital magnetic field detection sensor. The system includes specific sensing elements and an IC interface capable of measuring both the linear acceleration and magnetic field applied to it and providing a signal to the external world through an I²C serial interface with separated digital output. The sensing system is manufactured using specialized micromachining processes, while the IC interfaces are manufactured using CMOS technology that allows designing a dedicated circuit which is trimmed to better match the sensing element characteristics.

 

The LSM303DLHC features two data-ready signals (RDY) which indicate when a new set of measured acceleration data and magnetic data are available, therefore simplifying data synchronization in the digital system that uses the device. The LSM303DLHC may also be configured to generate a free-fall interrupt signal according to a programmed acceleration event along the enabled axes. Linear acceleration operating mode: The LSM303DLHC provides two different acceleration operating modes: “normal mode” and “low-power mode”. While normal mode guarantees high resolution, low-power mode further reduces current consumption. Table 8 summarizes how to select the operating mode.

 

Datasheet

LSM303DLHC-STMicroelectronics-Datasheet

Product Attributes

Type Description
Category Sensors, Transducers Motion Sensors - IMUs
Mfr STMicroelectronics
Series -
Package Tray
Part Status Obsolete
Sensor Type Accelerometer, Magnetometer, 6 Axis
Output Type I²C
Operating Temperature -40°C ~ 85°C (TA)
Package / Case 14-VFLGA
Supplier Device Package 14-LGA (3x5)
Mounting Type Surface Mount
Base Product Number LSM303

 

Magnetic Field Digital Interface

For magnetic sensors the default (factory) 7-bit slave address is 0011110xb. The slave address is completed with a Read/Write bit. If the bit is ‘1’ (read), a repeated START (SR) condition must be issued after the two sub-address bytes. If the bit is ‘0’ (write) the master transmits to the slave with the direction unchanged. Table 16 explains how the SAD is composed.

 

Magnetic signal interface reading/writing The interface uses an address pointer to indicate which register location is to be read from or written to. These pointer locations are sent from the master to this slave device and succeed the 7-bit address plus 1 bit Read/Write identifier. To minimize the communication between the master and magnetic digital interface of LSM303DLHC, the address pointer updates automatically without master intervention.

 

This automatic address pointer update has two additional features. First, when address 12 or higher is accessed, the pointer updates to address 00, and secondly, when address 08 is reached, the pointer rolls back to address 03.

 

Logically, the address pointer operation functions as shown below. If (address pointer = 08) then the address pointer = 03 Or else, if (address pointer >= 12) then the address pointer = 0 Or else, (address pointer) = (address pointer) + 1 The address pointer value itself cannot be read via the I2C bus. Any attempt to read an invalid address location returns 0, and any write to an invalid address location, or an undefined bit within a valid address location, is ignored by this device.

 

Using Warning

Please check their parameters and pin configuration before replacing them in your circuit.

 

FAQ

  • What is the standard and fast mode of the LSM303DLHC?

100 kHz and 400 kHz

 

  • What is the temperature range of the LSM303DLHC?

-40 °C to +85 °C

Kynix

Kynix was founded in 2008, specializing in the electronic components distribution business. We adhere to honesty and ethics as our business philosophy and have gradually established an excellent reputation and credibility in our international business. With the accurate quotation, excellent credit, reasonable price, reliable quality, fast delivery, and authentic service, we have won the praise of the majority of customers.

Join our mailing list!

Be the first to know about new products, special offers, and more.

Leave a Reply

We'd love to hear from you! Feel free to share your thoughts and comments below. Rest assured, your email address will remain private.

Name *
Email *
Captcha *
Rating:

Kynix

  • How to purchase

  • Order
  • Search & Inquiry
  • Shipping & Tracking
  • Payment Methods
  • Contact Us

  • Tel: 00852-6915 1330
  • Email: info@kynix.com
  • Follow Us

authentication

Kynix

© 2008-2026 kynix.com all rights reserve.